| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
defs
The TI J7200 EVM base board has TI DP83867 PHY connected to external CPSW
NUSS Port 1 in rgmii-rxid mode.
Hence, add pinmux and Ethernet PHY configuration for TI J7200 SoC MCU
Gigabit Ethernet two ports Switch subsystem (CPSW NUSS).
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Suman Anna <s-anna@ti.com>
Link: https://lore.kernel.org/r/20200923220938.30788-5-grygorii.strashko@ti.com
|
|
Add DT node for The TI J7200 MCU SoC Gigabit Ethernet two ports Switch
subsystem (MCU CPSW NUSS).
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Suman Anna <s-anna@ti.com>
Link: https://lore.kernel.org/r/20200923220938.30788-4-grygorii.strashko@ti.com
|
|
Add DT node for Main NAVSS CPTS module.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Suman Anna <s-anna@ti.com>
Link: https://lore.kernel.org/r/20200923220938.30788-3-grygorii.strashko@ti.com
|
|
Add the ringacc and udmap nodes for Main and MCU NAVSS.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Suman Anna <s-anna@ti.com>
Link: https://lore.kernel.org/r/20200923220938.30788-2-grygorii.strashko@ti.com
|
|
Espressobin boards have 3 ethernet ports and some of them got assigned more
then one MAC address. MAC addresses are stored in U-Boot environment.
Since commit a2c7023f7075c ("net: dsa: read mac address from DT for slave
device") kernel can use MAC addresses from DT for particular DSA port.
Currently Espressobin DTS file contains alias just for ethernet0.
This patch defines additional ethernet aliases in Espressobin DTS files, so
bootloader can fill correct MAC address for DSA switch ports if more MAC
addresses were specified.
DT alias ethernet1 is used for wan port, DT aliases ethernet2 and ethernet3
are used for lan ports for both Espressobin revisions (V5 and V7).
Fixes: 5253cb8c00a6f ("arm64: dts: marvell: espressobin: add ethernet alias")
Cc: <stable@vger.kernel.org> # a2c7023f7075c: dsa: read mac address
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Andre Heider <a.heider@gmail.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
sm8250 has 24 thermal sensors split across two tsens controllers. Add
the thermal zones to expose them and wireup the cpus to throttle on
crossing passive temperature thresholds.
Signed-off-by: Amit Kucheria <amitk@kernel.org>
Link: https://lore.kernel.org/r/89b83b3caa4e32db08fe402cfa510feb25232aa0.1599732068.git.amitk@kernel.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Enable CONFIG_SND_SOC_QCOM and several platform drivers to be built as modules.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20200917203913.3250205-3-dmitry.baryshkov@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Enable GPU Clock Controller for SM8150 and SM8250 to allow using
Adreon GPU on these SoCs.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20200917203913.3250205-2-dmitry.baryshkov@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Enable CONFIG_INTERCONNECT and interconnect drivers for several Qualcomm
chipsets to enable bus bandwidth control on these SoCs.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20200917203913.3250205-1-dmitry.baryshkov@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Add support for J7200 Common Processor Board.
The EVM architecture is very similar to J721E as follows:
+------------------------------------------------------+
| +-------------------------------------------+ |
| | | |
| | Add-on Card 1 Options | |
| | | |
| +-------------------------------------------+ |
| |
| |
| +-------------------+ |
| | | |
| | SOM | |
| +--------------+ | | |
| | | | | |
| | Add-on | +-------------------+ |
| | Card 2 | | Power Supply
| | Options | | |
| | | | |
| +--------------+ | <---
+------------------------------------------------------+
Common Processor Board
Common Processor board is the baseboard that has most of the actual
connectors, power supply etc. A SOM (System on Module) is plugged on
to the common processor board and this contains the SoC, PMIC, DDR and
basic high speed components necessary for functionality.
Note:
* The minimum configuration required to boot up the board is System On
Module(SOM) + Common Processor Board.
* Since there is just a single SOM and Common Processor Board, we are
maintaining common processor board as the base dts and SOM as the dtsi
that we include. In the future as more SOM's appear, we should move
common processor board as a dtsi and include configurations as dts.
* All daughter cards beyond the basic boards shall be maintained as
overlays.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Suman Anna <s-anna@ti.com>
Link: https://lore.kernel.org/r/20200914162231.2535-6-lokeshvutla@ti.com
|
|
The J7200 SoC is a part of the K3 Multicore SoC architecture platform.
It is targeted for automotive gateway, vehicle compute systems,
Vehicle-to-Vehicle (V2V) and Vehicle-to-Everything (V2X) applications.
The SoC aims to meet the complex processing needs of modern embedded
products.
Some highlights of this SoC are:
* Dual Cortex-A72s in a single cluster, two clusters of lockstep
capable dual Cortex-R5F MCUs and a Centralized Device Management and
Security Controller (DMSC).
* Configurable L3 Cache and IO-coherent architecture with high data
throughput capable distributed DMA architecture under NAVSS.
* Integrated Ethernet switch supporting up to a total of 4 external ports
in addition to legacy Ethernet switch of up to 2 ports.
* Upto 1 PCIe-GEN3 controller, 1 USB3.0 Dual-role device subsystems,
20 MCANs, 3 McASP, eMMC and SD, OSPI/HyperBus memory controller, I3C
and I2C, eCAP/eQEP, eHRPWM among other peripherals.
* One hardware accelerator block containing AES/DES/SHA/MD5 called SA2UL
management.
See J7200 Technical Reference Manual (SPRUIU1, June 2020)
for further details: https://www.ti.com/lit/pdf/spruiu1
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Kishon Vijay Abraham I <kishon@ti.com>
Link: https://lore.kernel.org/r/20200914162231.2535-5-lokeshvutla@ti.com
|
|
To allow lesser dependency and better maintainability use CONFIG_ARCH_K3
for building dtbs for all K3 based devices. This is as per the
discussion in [0].
[0] https://lore.kernel.org/linux-arm-kernel/20200908112534.t5bgrjf7y3a6l2ss@akan/
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Suman Anna <s-anna@ti.com>
Link: https://lore.kernel.org/r/20200914162231.2535-2-lokeshvutla@ti.com
|
|
add missed ir-receiver and ir_rx pinctl nodes to rk3399-khadas-edge
Khadas Edge board uses gpio-ir-receiver on RK_PB6 gpio
Signed-off-by: Artem Lapkin <art@khadas.com>
Link: https://lore.kernel.org/r/20200923130823.1612533-3-art@khadas.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
The Khadas Edge Boards uses winbond - w25q128 spi flash with 104Mhz
Signed-off-by: Artem Lapkin <art@khadas.com>
Link: https://lore.kernel.org/r/20200923130823.1612533-2-art@khadas.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Enable support for the Toshiba Visconti SoCs.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
Reviewed-by: Punit Agrawal <punit1.agrawal@toshiba.co.jp>
|
|
Add basic support for the Visconti TMPV7708 SoC peripherals -
- CPU
- CA53 x 4 and 2 cluster.
- not support PSCI, currently only spin-table is supported.
- Interrupt controller (ARM Generic Interrupt Controller)
- Timer (ARM architected timer)
- UART (ARM PL011 UART controller)
- SPI (ARM PL022 SPI controller)
- I2C (Synopsys DesignWare APB I2C Controller)
- Pin control (Visconti specific)
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
Reviewed-by: Punit Agrawal <punit1.agrawal@toshiba.co.jp>
|
|
Add the initial device tree files for Toshiba Visconti platform.
For starters, the only SoC supported will be Visconti5 TMPV7708.
https://toshiba.semicon-storage.com/ap-en/semiconductor/product/image-recognition-processors-visconti.html
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
Reviewed-by: Punit Agrawal <punit1.agrawal@toshiba.co.jp>
|
|
compat_sys_mount is identical to the regular sys_mount now, so remove it
and use the native version everywhere.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Two minor conflicts:
1) net/ipv4/route.c, adding a new local variable while
moving another local variable and removing it's
initial assignment.
2) drivers/net/dsa/microchip/ksz9477.c, overlapping changes.
One pretty prints the port mode differently, whilst another
changes the driver to try and obtain the port mode from
the port node rather than the switch node.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This adds support for the NanoPi R2S from FriendlyARM.
Rockchip RK3328 SoC
1GB DDR4 RAM
Gigabit Ethernet (WAN)
Gigabit Ethernet (USB3) (LAN)
USB 2.0 Host Port
MicroSD slot
Reset button
WAN - LAN - SYS LED
Signed-off-by: David Bauer <mail@david-bauer.net>
Link: https://lore.kernel.org/r/20200920154528.88185-2-mail@david-bauer.net
[adapted from sdmmc0m1_gpio to renamed sdmmc0m1_pin]
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
J721E Common Processor Board has PCIe connectors for the 1st three PCIe
instances. Configure the three PCIe instances in RC mode and disable the
4th PCIe instance.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20200914152115.1788-3-kishon@ti.com
|
|
Add PCIe device tree nodes (both RC and EP) for the four
PCIe instances here.
Also add the missing translations required in the "ranges"
DT property of cbass_main to access all the four PCIe
instances.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20200914152115.1788-2-kishon@ti.com
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/tip/tip into HEAD
|
|
Correct the name of property for GPIO specifier in GPIO hog.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The RTC on Symphony board does not have its interrupt pin connected to
the SoC, therefore it is not capable of waking up.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
GPIO_ACTIVE_x flags are not correct in the context of interrupt flags.
These are simple defines so they could be used in DTS but they will not
have the same meaning:
1. GPIO_ACTIVE_HIGH = 0 = IRQ_TYPE_NONE
2. GPIO_ACTIVE_LOW = 1 = IRQ_TYPE_EDGE_RISING
Correct the interrupt flags, assuming the author of the code wanted same
logical behavior behind the name "ACTIVE_xxx", this is:
ACTIVE_LOW => IRQ_TYPE_LEVEL_LOW
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-By: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
GPIO_ACTIVE_x flags are not correct in the context of interrupt flags.
These are simple defines so they could be used in DTS but they will not
have the same meaning:
1. GPIO_ACTIVE_HIGH = 0 = IRQ_TYPE_NONE
2. GPIO_ACTIVE_LOW = 1 = IRQ_TYPE_EDGE_RISING
Correct the interrupt flags, assuming the author of the code wanted same
logical behavior behind the name "ACTIVE_xxx", this is:
ACTIVE_LOW => IRQ_TYPE_LEVEL_LOW
For level low interrupts, enable also internal pull up. It is
required at least on imx8mm-evk, according to schematics.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-By: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
GPIO_ACTIVE_x flags are not correct in the context of interrupt flags.
These are simple defines so they could be used in DTS but they will not
have the same meaning:
1. GPIO_ACTIVE_HIGH = 0 = IRQ_TYPE_NONE
2. GPIO_ACTIVE_LOW = 1 = IRQ_TYPE_EDGE_RISING
Correct the interrupt flags, assuming the author of the code wanted same
logical behavior behind the name "ACTIVE_xxx", this is:
ACTIVE_LOW => IRQ_TYPE_LEVEL_LOW
ACTIVE_HIGH => IRQ_TYPE_LEVEL_HIGH
In case of level low interrupts, enable also internal pull up. It is
required at least on imx8mm-evk, according to schematics.
The schematics for Variscite imx8mm-var-som are not available and
I was unable to get proper configuration from Variscite.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-By: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Conversion of int-gpios into interrupts property requires also
interrupt-parent and uses different flags.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
On LS1088A, watchdog clk are divided by 16, correct it in dts.
Signed-off-by: Zhao Qiang <qiang.zhao@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add a pwm-fan mapped to the PWM channel 0 which is connected to the
fan connector of the carrier.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Now that we have support for GPIO lines of the SMARC connector, enable
LED support on the KBox A-230-LS. There are two LEDs without fixed
functions, one is yellow and one is green. Unfortunately, it is just one
multi-color LED, thus while it is possible to enable both at the same
time it is hard to tell the difference between "yellow only" and "yellow
and green".
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Now that we have support for GPIO lines of the SMARC connector, map the
sleep, power and lid switch signals to the corresponding keys using the
gpio-keys and gpio-keys-polled drivers. The power and sleep signals have
dedicated interrupts, thus we use these ones. The lid switch is just
mapped to a GPIO input and needs polling.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add the board management controller node.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
imx8mq-evk has a MIPI DSI port that can be used to connect a Raydium
RM67191 panel.
Add support for it.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add label to pcie nodes so that they are easy to
refer.
Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
VAR-SOM-MX8MN
Add a basic DTS for Variscite Symphony evaluation kit with VAR-SOM-MX8MN
(i.MX 8M Nano) System on Module. This brings up the board with basic
functionalities although still few issues remain (e.g. I2C3 and USB OTG
port, although it might not be the problem of DTS).
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add DTSI of Variscite VAR-SOM-MX8MN (Nano) System on Module in a basic
version, delivered with Variscite Symphony Evaluation kit. This version
comes with:
- 1 GB of RAM,
- 16 GB eMMC,
- Gigabit Ethernet PHY,
- 802.11 ac/a/b/g/n WiFi with 4.2 Bluetooth,
- CAN bus,
- Audio codec (not yet configured in DTSI).
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This commit adds DMA controller present on Actions S700, it differs from
S900 in terms of number of dma channels and requests.
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
After commit 7cdf8446ed1d ("arm64: dts: actions: Add pinctrl node for
Actions Semi S700") following error has been observed while booting
Linux on Cubieboard7-lite(based on S700 SoC).
[ 0.257415] pinctrl-s700 e01b0000.pinctrl: can't request region for
resource [mem 0xe01b0000-0xe01b0fff]
[ 0.266902] pinctrl-s700: probe of e01b0000.pinctrl failed with error -16
This is due to the fact that memory range for "sps" power domain controller
clashes with pinctrl.
One way to fix it, is to limit pinctrl address range which is safe
to do as current pinctrl driver uses address range only up to 0x100.
This commit limits the pinctrl address range to 0x100 so that it doesn't
conflict with sps range.
Fixes: 7cdf8446ed1d ("arm64: dts: actions: Add pinctrl node for Actions
Semi S700")
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Suggested-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
Enable the kernel modules for the board management controller "sl28cpld"
which is used on the SMARC-sAL28 board.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Select the eLCDIF display controller and Raydium RM67191 panel drivers,
so that MIPI DSI can be functional by default on a imx8mq-evk board.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The pin configuration for PMIC interrupt is already set by
imx8mn-evk.dtsi with exactly the same values.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The Symphony board uses GPIO from expander as Ethernet PHY reset pin,
not the GPIO1_IO9.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The i2c3 clock frequency and pin configuration are already set by
imx8mm-var-som.dtsi.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The @node passed to cpumask_of_node() can be NUMA_NO_NODE, in that
case it will trigger the following WARN_ON(node >= nr_node_ids) due to
mismatched data types of @node and @nr_node_ids. Actually we should
return cpu_all_mask just like most other architectures do if passed
NUMA_NO_NODE.
Also add a similar check to the inline cpumask_of_node() in numa.h.
Signed-off-by: Zhengyuan Liu <liuzhengyuan@tj.kylinos.cn>
Reviewed-by: Gavin Shan <gshan@redhat.com>
Link: https://lore.kernel.org/r/20200921023936.21846-1-liuzhengyuan@tj.kylinos.cn
Signed-off-by: Will Deacon <will@kernel.org>
|
|
Currently the code for displaying a stack trace on the console is located
in traps.c rather than stacktrace.c, using the unwinding code that is in
stacktrace.c. This can be confusing and make the code hard to find since
such output is often referred to as a stack trace which might mislead the
unwary. Due to this and since traps.c doesn't interact with this code
except for via the public interfaces move the code to stacktrace.c to
make it easier to find.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20200921122341.11280-1-broonie@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
|
|
Commit 73f381660959 ("arm64: Advertise mitigation of Spectre-v2, or lack
thereof") changed the way we deal with ARCH_WORKAROUND_1, by moving most
of the enabling code to the .matches() callback.
This has the unfortunate effect that the workaround gets only enabled on
the first affected CPU, and no other.
In order to address this, forcefully call the .matches() callback from a
.cpu_enable() callback, which brings us back to the original behaviour.
Fixes: 73f381660959 ("arm64: Advertise mitigation of Spectre-v2, or lack thereof")
Cc: <stable@vger.kernel.org>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Will Deacon <will@kernel.org>
|
|
We seem to be pretending that we don't have any firmware mitigation
when KVM is not compiled in, which is not quite expected.
Bring back the mitigation in this case.
Fixes: 4db61fef16a1 ("arm64: kvm: Modernize __smccc_workaround_1_smc_start annotations")
Cc: <stable@vger.kernel.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Will Deacon <will@kernel.org>
|
|
In a follow-up patch, we may save the FPSIMD rather than the full SVE
state when the state has to be zeroed on return to userspace (e.g
during a syscall).
Introduce an helper to load SVE vectors from FPSIMD state and zero the rest
of SVE registers.
Signed-off-by: Julien Grall <julien.grall@arm.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Dave Martin <Dave.Martin@arm.com>
Link: https://lore.kernel.org/r/20200828181155.17745-7-broonie@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
|
