| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Although the schematics of Pine A64-LTS and SoPine Baseboard shows both
the RX and TX internal delay are enabled, they're using the same broken
RTL8211E chip batch with Pine A64+, so they should use TXID instead, not
ID.
In addition, by checking the real components soldered on both a SoPine
Baseboard and a Pine A64-LTS, RX delay is not enabled (GR69 soldered and
GR70 NC) despite the schematics says it's enabled. It's a common
situation for Pine64 boards that the NC information on schematics is not
the same with the board.
So the RGMII delay mode should be TXID on these boards.
Fixes: c2b111e59a7b ("arm64: dts: allwinner: A64 Sopine: phy-mode rgmii-id")
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210609083843.463750-1-icenowy@aosc.io
|
|
- Fixup MMC node names
- Fixup led node names
- Introduce new devicetree file for Raspberry Pi 400
- Introduce devicetree bindings for Raspberry Pi 400
- Fix issue with dwc2's FIFO's size
- Add VEC compatible for bcm2711
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
Add a basic GPU node for mt8183, as well as OPP table.
Note that with the current panfrost driver, devfreq is not
actually functional, as the we do not have platform-specific
support for >1 supplies. Also, we are missing code to handle
frequency change, as the GPU frequency needs to be switched
away to a stable 26Mhz clock during the transition.
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Link: https://lore.kernel.org/r/20210521200038.v14.1.I9f45f5c1f975422d58b5904d11546349e9ccdc94@changeid
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
|
|
The SCPI YAML schema expects standard node names for clocks and
power domain controllers. Fix those as per the schema for Juno
platforms.
Link: https://lore.kernel.org/r/20210608145133.2088631-1-sudeep.holla@arm.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
|
|
Add tboard thermal zones.
The tboard thermal sensors are a kind of NTC sensors which are located
on PCB board to correlate the temperature of the case (Tskin).
pull-up voltage: 1800 mv
pull-up resistor: 75K
Vsense = pull-up voltage * Rntc / ( pull-up resistor + Rntc )
AuxIn = Vsense * 4096 / 1500
Signed-off-by: Michael Kao <michael.kao@mediatek.com>
Signed-off-by: Ben Tseng <ben.tseng@mediatek.com>
Tested-by: Hsin-Yi Wang <hsinyi@chromium.org>
Link: https://lore.kernel.org/r/20210604093755.13288-1-ben.tseng@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
|
|
Add a 'cbas' device node for supporting tablet mode switch in
kukui devices.
Kukui platforms with detacheable base have an additional input
device under cros-ec, which reports SW_TABLET_MODE regarding
its base state (e.g. base flipped or detached).
Signed-off-by: Ikjoon Jang <ikjn@chromium.org>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20210609032554.2443675-1-ikjn@chromium.org
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
|
|
This adds a reference to the dts of the Raspberry Pi 400,
so we don't need to maintain the content in arm64.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Nicolas Saenz Julienne <nsaenz@kernel.org>
Link: https://lore.kernel.org/r/1622981777-5023-8-git-send-email-stefan.wahren@i2se.com
Signed-off-by: Nicolas Saenz Julienne <nsaenz@kernel.org>
|
|
It would be helpful if mem_abort_decode() could decode the DFSC/IFSC, as
this can make it easier to identify common bugs (e.g. accesses which
trigger alignment faults) without having to manually decode the xFSC
value.
Decode the xFSC in mem_abort_decode().
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Robin Murphy <robin.murphy@arm.com>
Cc: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20210608123742.11921-1-mark.rutland@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
|
|
AM642-SK has no PCIe slot. Disable it here.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20210603142251.14563-6-kishon@ti.com
|
|
Enable USB Super-Speed HOST port.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Reviewed-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20210603142251.14563-5-kishon@ti.com
|
|
AM642 EVM has a x4 lane PCIe connector. Enable PCIe in RC mode here.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20210603142251.14563-4-kishon@ti.com
|
|
AM64 has one PCIe instance which can be configured in either
host mode (RC) or device mode (EP). Add PCIe DT node for host
mode and device mode here.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20210603142251.14563-3-kishon@ti.com
|
|
AM64 has one SERDES 10G instance. Add SERDES DT node for it.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20210603142251.14563-2-kishon@ti.com
|
|
Commit 66db854b1f62d ("arm64: dts: ti: k3-j721e-common-proc-board:
Configure the PCIe instances") and
commit 02c35dca2b488 ("arm64: dts: ti: k3-j721e: Enable Super-Speed
support for USB0") added PHY DT nodes with node name as "link"
However nodes with #phy-cells should be named 'phy' as discussed in [1].
Re-name subnodes of serdes in J721E to 'phy'.
[1] -> http://lore.kernel.org/r/20200909203631.GA3026331@bogus
Fixes: 66db854b1f62d ("arm64: dts: ti: k3-j721e-common-proc-board: Configure the PCIe instances")
Fixes: 02c35dca2b488 ("arm64: dts: ti: k3-j721e: Enable Super-Speed support for USB0")
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20210603143427.28735-5-kishon@ti.com
|
|
Use external clock for all the SERDES used by PCIe controller. This will
make the same clock used by the local SERDES as well as the clock
provided to the PCIe connector.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20210603143427.28735-4-kishon@ti.com
|
|
Add #clock-cells property to serdes DT node since the serdes is also now
modeled as a clock provider and include the input clocks "pll0_refclk"
and "pll1_refclk" which are parents to the clocks modeled by serdes.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20210603143427.28735-3-kishon@ti.com
|
|
Rename the external refclk inputs to the SERDES from
dummy_cmn_refclk/dummy_cmn_refclk1 to cmn_refclk/cmn_refclk1
respectively. Also move the external refclk DT nodes outside the
cbass_main DT node. Since in j721e common processor board, only the
cmn_refclk1 is connected to 100MHz clock, fix the clock frequency.
Fixes: afd094ebe69f ("arm64: dts: ti: k3-j721e-main: Add WIZ and SERDES PHY nodes")
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20210603143427.28735-2-kishon@ti.com
|
|
SMCCC v1.2 requires that all SVE state be preserved over SMC calls which
introduces substantial overhead in the common case where there is no SVE
state in the registers. To avoid this SMCCC v1.3 introduces a flag which
allows the caller to say that there is no state that needs to be preserved
in the registers. Make use of this flag, setting it if the SMCCC version
indicates support for it and the TIF_ flags indicate that there is no live
SVE state in the registers, this avoids placing any constraints on when
SMCCC calls can be done or triggering extra saving and reloading of SVE
register state in the kernel.
This would be straightforward enough except for the rather entertaining
inline assembly we use to do SMCCC v1.1 calls to allow us to take advantage
of the limited number of registers it clobbers. Deal with this by having a
function which we call immediately before issuing the SMCCC call to make
our checks and set the flag. Using alternatives the overhead if SVE is
supported but not detected at runtime can be reduced to a single NOP.
Signed-off-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210603184118.15090-1-broonie@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
|
|
Enable support for audio-graph based sound card on Jetson Xavier NX.
Following I/O interfaces are enabled.
- I2S3 and I2S5
- DMIC1, DMIC2 and DMIC4
- DSPK1 and DSPK2
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
This enables the adreno-specific SMMU path that sets HUPCF so
(user-managed) page faults don't wedge the GPU.
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210326231303.3071950-2-eric@anholt.net
Signed-off-by: Will Deacon <will@kernel.org>
|
|
The ICSSGs on K3 J721E SoCs contain an MDIO controller that can
be used to control external PHYs associated with the Industrial
Ethernet peripherals within each ICSSG instance. The MDIO module
used within the ICSSG is similar to the MDIO Controller used
in TI Davinci SoCs. A bus frequency of 1 MHz is chosen for the
MDIO operations.
The nodes are added and enabled in the common k3-j721e-main.dtsi
file by default, and disabled in the existing J721E board dts
file. These nodes need pinctrl lines, and so should be enabled
only on boards where they are actually wired and pinned out for
ICSSG Ethernet. Any new board dts file should disable these if
they are not sure.
Signed-off-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20210601150032.11432-3-s-anna@ti.com
|
|
The ICSSGs on K3 AM65x SoCs contain an MDIO controller that can
be used to control external PHYs associated with the Industrial
Ethernet peripherals within each ICSSG instance. The MDIO module
used within the ICSSG is similar to the MDIO Controller used
in TI Davinci SoCs. A bus frequency of 1 MHz is chosen for the
MDIO operations.
The nodes are added and enabled in the common k3-am65-main.dtsi
file by default, and disabled in the existing AM65 board dts
files. These nodes need pinctrl lines, and so should be enabled
only on boards where they are actually wired and pinned out for
ICSSG Ethernet. Any new board dts file should disable these if
they are not sure.
Signed-off-by: Roger Quadros <rogerq@ti.com>
[s-anna@ti.com: move the disabled status to board dts files]
Signed-off-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20210601150032.11432-2-s-anna@ti.com
|
|
UHS-I speed modes are supported in AM65 S.R. 2.0 SoC[1].
Add support by removing the no-1-8-v tag and including the voltage
regulator device tree nodes for power cycling.
However, the 4 bit interface of AM65 SR 1.0 cannot be supported at 3.3 V or
1.8 V because of erratas i2025 and i2026 [2]. As the SD card is the primary
boot mode for development usecases, continue to enable SD card and disable
UHS-I modes in it to minimize any ageing issues happening because of
erratas.
k3-am6528-iot2050-basic and k3-am6548-iot2050-advanced boards use S.R. 1.0
version of AM65 SoC. Therefore, add no-1-8-v in sdhci1 device tree node of
the common iot2050 device tree file.
[1] - https://www.ti.com/lit/ug/spruid7e/spruid7e.pdf, section 12.3.6.1.1
[2] - https://www.ti.com/lit/er/sprz452e/sprz452e.pdf
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Acked-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20210529033749.6250-1-a-govindraju@ti.com
|
|
The low-level idle code in arch_cpu_idle() and its callees runs at a
time where where portions of the kernel environment aren't available.
For example, RCU may not be watching, and lockdep state may be
out-of-sync with the hardware. Due to this, it is not sound to
instrument this code.
We generally avoid instrumentation by marking the entry functions as
`noinstr`, but currently this doesn't inhibit KCOV instrumentation.
Prevent this by factoring these functions into a new idle.c so that we
can disable KCOV for the entire compilation unit, as is done for the
core idle code in kernel/sched/idle.c.
We'd like to keep instrumentation of the rest of process.c, and for the
existing code in cpuidle.c, so a new compilation unit is preferable. The
arch_cpu_idle_dead() function in process.c is a cpu hotplug function
that is safe to instrument, so it is left as-is in process.c.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Cc: James Morse <james.morse@arm.com>
Cc: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20210607094624.34689-21-mark.rutland@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
|
|
The code in entry-common.c runs at exception entry and return
boundaries, where portions of the kernel environment aren't available.
For example, RCU may not be watching, and lockdep state may be
out-of-sync with the hardware. Due to this, it is not sound to
instrument this code.
We generally avoid instrumentation by marking the entry functions as
`noinstr`, but currently this doesn't inhibit KCOV instrumentation.
Prevent this by disabling KCOV for the entire compilation unit.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Cc: James Morse <james.morse@arm.com>
Cc: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20210607094624.34689-20-mark.rutland@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
|
|
Now that we only call arm64_enter_nmi() and arm64_exit_nmi() from within
entry-common.c, let's make these static to ensure this remains the case.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Joey Gouly <joey.gouly@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20210607094624.34689-19-mark.rutland@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
|
|
We'd like to keep all the entry sequencing in entry-common.c, as this
will allow us to ensure this is consistent, and free from any unsound
instrumentation.
Currently __sdei_handler() performs the NMI entry/exit sequences in
sdei.c. Let's split the low-level entry sequence from the event
handling, moving the former to entry-common.c and keeping the latter in
sdei.c. The event handling function is renamed to do_sdei_event(),
matching the do_${FOO}() pattern used for other exception handlers.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Joey Gouly <joey.gouly@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20210607094624.34689-18-mark.rutland@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
|
|
We'd like to keep all the entry sequencing in entry-common.c, as this
will allow us to ensure this is consistent, and free from any unsound
instrumentation.
Currently handle_bad_stack() performs the NMI entry sequence in traps.c.
Let's split the low-level entry sequence from the reporting, moving the
former to entry-common.c and keeping the latter in traps.c. To make it
clear that reporting function never returns, it is renamed to
panic_bad_stack().
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Joey Gouly <joey.gouly@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20210607094624.34689-17-mark.rutland@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
|
|
An unexpected synchronous exception from EL1h could happen at any time,
and for robustness we should treat this as an NMI, making minimal
assumptions about the context the exception was taken from.
Currently el1_inv() assumes we can use enter_from_kernel_mode(), and
also assumes that we should inherit the original DAIF value. Neither of
these are desireable when we take an unexpected exception. Further,
after el1_inv() calls __panic_unhandled(), the remainder of the function
is unreachable, and therefore superfluous.
Let's address this and simplify things by having el1h_64_sync_handler()
call __panic_unhandled() directly, without any of the redundant logic.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Reported-by: Joey Gouly <joey.gouly@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20210607094624.34689-16-mark.rutland@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
|
|
We have 16 architectural exception vectors, and depending on kernel
configuration we handle 8 or 12 of these with C code, with the remaining
8 or 4 of these handled as special cases in the entry assembly.
It would be nicer if the entry assembly were uniform for all exceptions,
and we deferred any specific handling of the exceptions to C code. This
way the entry assembly can be more easily templated without ifdeffery or
special cases, and it's easier to modify the handling of these cases in
future (e.g. to dump additional registers other context).
This patch reworks the entry code so that we always have a C handler for
every architectural exception vector, with the entry assembly being
completely uniform. We now have to handle exceptions from EL1t and EL1h,
and also have to handle exceptions from AArch32 even when the kernel is
built without CONFIG_COMPAT. To make this clear and to simplify
templating, we rename the top-level exception handlers with a consistent
naming scheme:
asm: <el+sp>_<regsize>_<type>
c: <el+sp>_<regsize>_<type>_handler
.. where:
<el+sp> is `el1t`, `el1h`, or `el0t`
<regsize> is `64` or `32`
<type> is `sync`, `irq`, `fiq`, or `error`
... e.g.
asm: el1h_64_sync
c: el1h_64_sync_handler
... with lower-level handlers simply using "el1" and "compat" as today.
For unexpected exceptions, this information is passed to
__panic_unhandled(), so it can report the specific vector an unexpected
exception was taken from, e.g.
| Unhandled 64-bit el1t sync exception
For vectors we never expect to enter legitimately, the C code is
generated using a macro to avoid code duplication. The exceptions are
handled via __panic_unhandled(), replacing bad_mode() (which is
removed).
The `kernel_ventry` and `entry_handler` assembly macros are updated to
handle the new naming scheme. In theory it should be possible to
generate the entry functions at the same time as the vectors using a
single table, but this will require reworking the linker script to split
the two into separate sections, so for now we have separate tables.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Joey Gouly <joey.gouly@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20210607094624.34689-15-mark.rutland@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
|
|
Now that the majority of the exception triage logic has been converted
to C, the entry assembly functions all have a uniform structure.
Let's generate them all with an assembly macro to reduce the amount of
code and to ensure they all remain in sync if we make changes in future.
There should be no functional change as a result of this patch.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Joey Gouly <joey.gouly@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20210607094624.34689-14-mark.rutland@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
|
|
Our use of bad_mode() has a few rough edges:
* AArch64 doesn't use the term "mode", and refers to "Execution
states", "Exception levels", and "Selected stack pointer".
* We log the exception type (SYNC/IRQ/FIQ/SError), but not the actual
"mode" (though this can be decoded from the SPSR value).
* We use bad_mode() as a second-level handler for unexpected synchronous
exceptions, where the "mode" is legitimate, but the specific exception
is not.
* We dump the ESR value, but call this "code", and so it's not clear to
all readers that this is the ESR.
... and all of this can be somewhat opaque to those who aren't extremely
familiar with the code.
Let's make this a bit clearer by having bad_mode() log "Unhandled
${TYPE} exception" rather than "Bad mode in ${TYPE} handler", using
"ESR" rather than "code", and having the final panic() log "Unhandled
exception" rather than "Bad mode".
In future we'd like to log the specific architectural vector rather than
just the type of exception, so we also split the core of bad_mode() out
into a helper called __panic_unhandled(), which takes the vector as a
string argument.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Joey Gouly <joey.gouly@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20210607094624.34689-13-mark.rutland@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
|
|
In subsequent patches we'll rework the way bad_mode() is called by
exception entry code. In preparation for this, let's move bad_mode()
itself into entry-common.c.
Let's also mark it as noinstr (e.g. to prevent it being kprobed), and
let's also make the `handler` array a local variable, as this is only
use by bad_mode(), and will be removed entirely in a subsequent patch.
There should be no functional change as a result of this patch.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Joey Gouly <joey.gouly@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20210607094624.34689-12-mark.rutland@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
|
|
Following the example of ret_to_user, let's consolidate all the EL1
return paths with a ret_to_kernel helper, rather than each entry point
having its own copy of the return code.
There should be no functional change as a result of this patch.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Joey Gouly <joey.gouly@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20210607094624.34689-11-mark.rutland@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
|
|
In subsequent patches we'll rename the entry handlers based on their
original EL, register width, and exception class. To do so, we need to
make all 3 mandatory arguments to the `kernel_ventry` macro, and
distinguish EL1h from EL1t.
In preparation for this, let's make the current set of arguments
mandatory, and move the `regsize` column before the branch label suffix,
making the vectors easier to read column-wise.
There should be no functional change as a result of this patch.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Joey Gouly <joey.gouly@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20210607094624.34689-10-mark.rutland@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
|
|
In entry.S we have two comments which distinguish EL0 and EL1 exception
handlers, but the code isn't actually laid out to match, and there are a
few other inconsistencies that would be good to clear up.
This patch organizes the entry handers consistently:
* The handlers are laid out in order of the vectors, to make them easier
to navigate.
* The inconsistently-applied alignment is removed
* The handlers are consistently marked with SYM_CODE_START_LOCAL()
rather than SYM_CODE_START_LOCAL_NOALIGN(), giving them the same
default alignment as other assembly code snippets.
There should be no functional change as a result of this patch.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Joey Gouly <joey.gouly@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20210607094624.34689-9-mark.rutland@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
|
|
For various reasons we'd like to convert the bulk of arm64's exception
triage logic to C. As a step towards that, this patch converts the EL1
and EL0 IRQ+FIQ triage logic to C.
Separate C functions are added for the native and compat cases so that
in subsequent patches we can handle native/compat differences in C.
Since the triage functions can now call arm64_apply_bp_hardening()
directly, the do_el0_irq_bp_hardening() wrapper function is removed.
Since the user_exit_irqoff macro is now unused, it is removed. The
user_enter_irqoff macro is still used by the ret_to_user code, and
cannot be removed at this time.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Joey Gouly <joey.gouly@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20210607094624.34689-8-mark.rutland@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
|
|
When handling IRQ/FIQ exceptions the entry assembly may transition from
a task's stack to a CPU's IRQ stack (and IRQ shadow call stack).
In subsequent patches we want to migrate the IRQ/FIQ triage logic to C,
and as we want to perform some actions on the task stack (e.g. EL1
preemption), we need to switch stacks within the C handler. So that we
can do so, this patch adds a helper to call a function on a CPU's IRQ
stack (and shadow stack as appropriate).
Subsequent patches will make use of the new helper function.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Cc: James Morse <james.morse@arm.com>
Cc: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20210607094624.34689-7-mark.rutland@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
|
|
Currently portions of our preempt logic are written in C while other
parts are written in assembly. Let's clean this up a little bit by
moving the NMI preempt checks to C. For now, the preempt count (and
need_resched) checking is left in assembly, and will be converted
with the body of the IRQ handler in subsequent patches.
Other than the increased lockdep coverage there should be no functional
change as a result of this patch.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Joey Gouly <joey.gouly@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20210607094624.34689-6-mark.rutland@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
|
|
Subsequent patches will pull more of the IRQ entry handling into C. To
keep this in one place, let's move arm64_preempt_schedule_irq() into
entry-common.c along with the other entry management functions.
We no longer need to include <linux/lockdep.h> in process.c, so the
include directive is removed.
There should be no functional change as a result of this patch.
Reviewed-by Joey Gouly <joey.gouly@arm.com>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Cc: James Morse <james.morse@arm.com>
Cc: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20210607094624.34689-5-mark.rutland@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
|
|
For various reasons we'd like to convert the bulk of arm64's exception
triage logic to C. As a step towards that, this patch converts the EL1
and EL0 SError triage logic to C.
Separate C functions are added for the native and compat cases so that
in subsequent patches we can handle native/compat differences in C.
There should be no functional change as a result of this patch.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Joey Gouly <joey.gouly@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20210607094624.34689-4-mark.rutland@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
|
|
For non-fatal exceptions taken from EL0, we expect that at some point
during exception handling it is possible to return to a regular process
context with all exceptions unmasked (e.g. as we do in
do_notify_resume()), and we generally aim to unmask exceptions wherever
possible.
While handling SError and debug exceptions from EL0, we need to leave
some exceptions masked during handling. Handling SError requires us to
mask SError (which also requires masking IRQ+FIQ), and handing debug
exceptions requires us to mask debug (which also requires masking
SError+IRQ+FIQ).
Once do_serror() or do_debug_exception() has returned, we no longer need
to mask exceptions, and can unmask them all, which is what we did prior
to commit:
9034f6251572a474 ("arm64: Do not enable IRQs for ct_user_exit")
... where we had to mask IRQs as for context_tracking_user_exit()
expected IRQs to be masked.
Since then, we realised that our context tracking wasn't entirely
correct, and reworked the entry code to fix this. As of commit:
23529049c6842382 ("arm64: entry: fix non-NMI user<->kernel transitions")
... we replaced the call to context_tracking_user_exit() with a call to
user_exit_irqoff() as part of enter_from_user_mode(), which occurs
earlier, before we run the body of the handler and unmask exceptions in
DAIF.
When we return to userspace, we go via ret_to_user(), which masks
exceptions in DAIF prior to calling user_enter_irqoff() as part of
exit_to_user_mode().
Thus, there's no longer a reason to leave IRQs or FIQs masked at the end
of the EL0 debug or error handlers, as neither the user exit context
tracking nor the user entry context tracking requires this. Let's bring
these into line with other EL0 exception handlers and ensure that IRQ
and FIQ are unmasked in DAIF at some point during the handler.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Joey Gouly <joey.gouly@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20210607094624.34689-3-mark.rutland@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
|
|
Upon taking an exception, the CPU sets all the DAIF bits. We never
clear any of these bits prior to calling bad_mode(), and bad_mode()
itself never clears any of these bits, so there's no need to call
local_daif_mask().
This patch removes the redundant call.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Joey Gouly <joey.gouly@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20210607094624.34689-2-mark.rutland@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
|
|
Wire up the quotactl_fd syscall.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
"make dtbs_check":
arm64/boot/dts/renesas/r8a779a0-falcon.dt.yaml: interrupt-controller@f1000000: 'power-domains' does not match any of the regexes: '^(msi-controller|gic-its|interrupt-controller)@[0-9a-f]+$', '^gic-its@', '^interrupt-controller@[0-9a-f]+$', 'pinctrl-[0-9]+'
From schema: Documentation/devicetree/bindings/interrupt-controller/arm,gic-v3.yaml
Remove the "power-domains" property, as the GIC on R-Car V3U is
always-on, and not part of a clock domain.
Fixes: 834c310f541839b6 ("arm64: dts: renesas: Add Renesas R8A779A0 SoC support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/a9ae5cbc7c586bf2c6b18ddc665ad7051bd1d206.1622560236.git.geert+renesas@glider.be
|
|
Populate the device node for the Interrupt Controller for External
Devices (INTC-EX) on R-Car M3-W+, which serves external IRQ pins
IRQ[0-5].
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/6f3cc1a1b6d777e743a7a9e66a80aaf9d5232a4f.1622547125.git.geert+renesas@glider.be
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Olof Johansson:
"A set of fixes that have been coming in over the last few weeks, the
usual mix of fixes:
- DT fixups for TI K3
- SATA drive detection fix for TI DRA7
- Power management fixes and a few build warning removals for OMAP
- OP-TEE fix to use standard API for UUID exporting
- DT fixes for a handful of i.MX boards
And a few other smaller items"
* tag 'arm-soc-fixes-v5.13-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (29 commits)
arm64: meson: select COMMON_CLK
soc: amlogic: meson-clk-measure: remove redundant dev_err call in meson_msr_probe()
ARM: OMAP1: ams-delta: remove unused function ams_delta_camera_power
bus: ti-sysc: Fix flakey idling of uarts and stop using swsup_sidle_act
ARM: dts: imx: emcon-avari: Fix nxp,pca8574 #gpio-cells
ARM: dts: imx7d-pico: Fix the 'tuning-step' property
ARM: dts: imx7d-meerkat96: Fix the 'tuning-step' property
arm64: dts: freescale: sl28: var1: fix RGMII clock and voltage
arm64: dts: freescale: sl28: var4: fix RGMII clock and voltage
ARM: imx: pm-imx27: Include "common.h"
arm64: dts: zii-ultra: fix 12V_MAIN voltage
arm64: dts: zii-ultra: remove second GEN_3V3 regulator instance
arm64: dts: ls1028a: fix memory node
bus: ti-sysc: Fix am335x resume hang for usb otg module
ARM: OMAP2+: Fix build warning when mmc_omap is not built
ARM: OMAP1: isp1301-omap: Add missing gpiod_add_lookup_table function
ARM: OMAP1: Fix use of possibly uninitialized irq variable
optee: use export_uuid() to copy client UUID
arm64: dts: ti: k3*: Introduce reg definition for interrupt routers
arm64: dts: ti: k3-am65|j721e|am64: Map the dma / navigator subsystem via explicit ranges
...
|
|
MMIO block mapping support from Keqian Zhu, allowing larger
(and lazy) mappings for devices assigned to guests.
* kvm-arm64/mmu/MMIO-block-mapping:
KVM: arm64: Try stage2 block mapping for host device MMIO
KVM: arm64: Remove the creation time's mapping of MMIO regions
|
|
Microsoft Surface Duo is based on SM8150 chipset. This new Device Tree
is a copy of sm8150-mtp with a the addition of the volume up key and
relevant i2c nodes.
Signed-off-by: Felipe Balbi <felipe.balbi@microsoft.com>
Link: https://lore.kernel.org/r/20210603122923.1919624-1-balbi@kernel.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Enable IPA on the SDM845 MTP.
Signed-off-by: Alex Elder <elder@linaro.org>
Link: https://lore.kernel.org/r/20200519123258.29228-1-elder@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
