| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Arnd Bergmann:
"This is a first set of bug fixes on top of what was merged for 4.7.
Two patches for lpc32xx address a harmless build warning that was just
introduced, one patch for the mediatek soc driver fixes a warning for
arm64, and the pxa changes are minor cleanups that should have been
part of the original pull requests but that I forgot to apply to the
cleanup-fixes branch earlier"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: lpc32xx: fix NR_IRQS confict
ARM: lpc32xx: remove legacy irq controller driver
soc: mtk-pmic-wrap: avoid integer overflow warning
ARM: pxa: Remove CLK_IS_ROOT
ARM: pxa: activate pinctrl for device-tree machines
|
|
Pull MTD updates from Brian Norris:
"First cycle with Boris as NAND maintainer! Many (most) bullets stolen
from him.
Generic:
- Migrated NAND LED trigger to be a generic MTD trigger
NAND:
- Introduction of the "ECC algorithm" concept, to avoid overloading
the ECC mode field too much more
- Replaced the nand_ecclayout infrastructure with something a little
more flexible (finally!) and future proof
- Rework of the OMAP GPMC and NAND drivers; the TI folks pulled some
of this into their own tree as well
- Prepare the sunxi NAND driver to receive DMA support
- Handle bitflips in erased pages on GPMI revisions that do not
support this in hardware.
SPI NOR:
- Start using the spi_flash_read() API for SPI drivers that support
it (i.e., SPI drivers with special memory-mapped flash modes)
And other small scattered improvments"
* tag 'for-linus-20160523' of git://git.infradead.org/linux-mtd: (155 commits)
mtd: spi-nor: support GigaDevice gd25lq64c
mtd: nand_bch: fix spelling of "probably"
mtd: brcmnand: respect ECC algorithm set by NAND subsystem
gpmi-nand: Handle ECC Errors in erased pages
Documentation: devicetree: deprecate "soft_bch" nand-ecc-mode value
mtd: nand: add support for "nand-ecc-algo" DT property
mtd: mtd: drop NAND_ECC_SOFT_BCH enum value
mtd: drop support for NAND_ECC_SOFT_BCH as "soft_bch" mapping
mtd: nand: read ECC algorithm from the new field
mtd: nand: fsmc: validate ECC setup by checking algorithm directly
mtd: nand: set ECC algorithm to Hamming on fallback
staging: mt29f_spinand: set ECC algorithm explicitly
CRIS v32: nand: set ECC algorithm explicitly
mtd: nand: atmel: set ECC algorithm explicitly
mtd: nand: davinci: set ECC algorithm explicitly
mtd: nand: bf5xx: set ECC algorithm explicitly
mtd: nand: omap2: Fix high memory dma prefetch transfer
mtd: nand: omap2: Start dma request before enabling prefetch
mtd: nandsim: add __init attribute
mtd: nand: move of_get_nand_xxx() helpers into nand_base.c
...
|
|
Merge "pxa changes for v4.7 cycle" from Robert Jarzmik:
This is a minor cycle with :
- cleanup fix from Stephen on clocks (CLK_ROOT deprecated)
- pin control activation for device-tree platforms
* tag 'pxa-for-4.7' of https://github.com/rjarzmik/linux:
ARM: pxa: Remove CLK_IS_ROOT
ARM: pxa: activate pinctrl for device-tree machines
These should have been part of the original pull request but got
accidentally dropped. Both changes in this branch can be considered
bugfixes, so I'm putting them in the fixes branch now.
|
|
|
|
Implementing the mtd_ooblayout_ops interface is the new way of exposing
ECC/OOB layout to MTD users.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
This flag is a no-op now (see commit 47b0eeb3dc8a "clk: Deprecate
CLK_IS_ROOT", 2016-02-02) so remove it.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
Pincontrol is not yet ready for all PXA platforms.
For example, a legacy platform, if PINCTRL was activated, will fail its
calls to gpio_request() or gpio_direction_output(), as the pinctrl
driver might not be available, such as for pxa25x and pxa3xx.
As a step forward, activate pincontrol for all device-tree available
machines, ie. pxa27x device-tree based and pxa3xx device-tree based.
If it appears later that pincontrol is also required for legacy
platforms and if the mfp->pinctrl conversion can be achieved, then
PINCTRL will be activated for the whole PXA architecture.
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Since device_add_property_set() now always takes a copy of
the property_set, and also since the fwnode type is always
hard coded to be FWNODE_PDATA, there is no need for the
drivers to deliver the entire struct property_set. The
function can just create the instance of it on its own and
bind the properties from the drivers to it on the spot.
This renames device_add_property_set() to
device_add_properties(). The function now takes struct
property_entry as its parameter instead of struct
property_set.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The number of requestor lines was clamped to 0 for all pxa architectures
in the requestor declaration. Fix this by using the value.
Fixes: 72b195cb7162 ("ARM: pxa: add the number of DMA requestor lines")
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates from Arnd Bergmann:
"Newly added support for additional SoCs:
- Axis Artpec-6 SoC family
- Allwinner A83T SoC
- Mediatek MT7623
- NXP i.MX6QP SoC
- ST Microelectronics stm32f469 microcontroller
New features:
- SMP support for Mediatek mt2701
- Big-endian support for NXP i.MX
- DaVinci now uses the new DMA engine dma_slave_map
- OMAP now uses the new DMA engine dma_slave_map
- earlyprintk support for palmchip uart on mach-tango
- delay timer support for orion
Other:
- Exynos PMU driver moved out to drivers/soc/
- Various smaller updates for Renesas, Xilinx, PXA, AT91, OMAP,
uniphier"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (83 commits)
ARM: uniphier: rework SMP code to support new System Bus binding
ARM: uniphier: add missing of_node_put()
ARM: at91: avoid defining CONFIG_* symbols in source code
ARM: DRA7: hwmod: Add data for eDMA tpcc, tptc0, tptc1
ARM: imx: Make reset_control_ops const
ARM: imx: Do L2 errata only if the L2 cache isn't enabled
ARM: imx: select ARM_CPU_SUSPEND only for imx6
dmaengine: pxa_dma: fix the maximum requestor line
ARM: alpine: select the Alpine MSI controller driver
ARM: pxa: add the number of DMA requestor lines
dmaengine: mmp-pdma: add number of requestors
dma: mmp_pdma: Add the #dma-requests DT property documentation
ARM: OMAP2+: Add rtc hwmod configuration for ti81xx
ARM: s3c24xx: Avoid warning for inb/outb
ARM: zynq: Move early printk virtual address to vmalloc area
ARM: DRA7: hwmod: Add custom reset handler for PCIeSS
ARM: SAMSUNG: Remove unused register offset definition
ARM: EXYNOS: Cleanup header files inclusion
drivers: soc: samsung: Enable COMPILE_TEST
MAINTAINERS: Add maintainers entry for drivers/soc/samsung
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input updates from Dmitry Torokhov:
"The most notable item is addition of support for Synaptics RMI4
protocol which is native protocol for all current Synaptics devices
(touchscreens, touchpads). In later releases we'll switch devices
using HID and PS/2 protocol emulation to RMI4.
You will also get:
- BYD PS/2 touchpad protocol support for psmouse
- MELFAS MIP4 Touchscreen driver
- rotary encoder was moved away from legacy platform data and to
generic device properties API, devm_* API, and can now handle
encoders using more than 2 GPIOs
- Cypress touchpad driver was switched to devm_* API and device
properties
- other assorted driver fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (40 commits)
ARM: pxa/raumfeld: use PROPERTY_ENTRY_INTEGER to define props
Input: synaptics-rmi4 - using logical instead of bitwise AND
Input: powermate - fix oops with malicious USB descriptors
Input: snvs_pwrkey - fix returned value check of syscon_regmap_lookup_by_phandle()
MAINTAINERS: add devicetree bindings to Input Drivers section
Input: synaptics-rmi4 - add device tree support to the SPI transport driver
Input: synaptics-rmi4 - add SPI transport driver
Input: synaptics-rmi4 - add support for F30
Input: synaptics-rmi4 - add support for F12
Input: synaptics-rmi4 - add device tree support for 2d sensors and F11
Input: synaptics-rmi4 - add support for 2D sensors and F11
Input: synaptics-rmi4 - add device tree support for RMI4 I2C devices
Input: synaptics-rmi4 - add I2C transport driver
Input: synaptics-rmi4 - add support for Synaptics RMI4 devices
Input: ad7879 - add device tree support
Input: ad7879 - fix default x/y axis assignment
Input: ad7879 - move header to platform_data directory
Input: ts4800 - add hardware dependency
Input: cyapa - fix for losing events during device power transitions
Input: sh_keysc - remove dependency on SUPERH
...
|
|
gcc-6.0 notices that the use of the property_entry in this file that
was recently introduced cannot work right, as we initialize the wrong
field:
raumfeld.c:387:3: error: the address of 'raumfeld_rotary_encoder_steps' will always evaluate as 'true' [-Werror=address]
DEV_PROP_U32, 1, &raumfeld_rotary_encoder_steps, },
^~~~~~~~~~~~
raumfeld.c:389:3: error: the address of 'raumfeld_rotary_encoder_axis' will always evaluate as 'true' [-Werror=address]
DEV_PROP_U32, 1, &raumfeld_rotary_encoder_axis, },
^~~~~~~~~~~~
raumfeld.c:391:3: error: the address of 'raumfeld_rotary_encoder_relative_axis' will always evaluate as 'true' [-Werror=address]
DEV_PROP_U32, 1, &raumfeld_rotary_encoder_relative_axis, },
^~~~~~~~~~~~
The problem appears to stem from relying on an old definition of
'struct property', but it has changed several times since the code
could have last been correct.
This changes the code to use the PROPERTY_ENTRY_INTEGER() macro instead,
which works fine for the current definition and is a safer way of doing
the initialization.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: a9e340dce3c3 ("Input: rotary_encoder - move away from platform data structure")
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Merge with Linux 4.5 to get PROPERTY_ENTRY_INTEGER() that is needed to
fix pxa/raumfeld rotary encoder properties.
|
|
ixp4xx and pxa25x both use this driver and provide a slightly
different set of register definitions for it. Aside from that,
the definition in the ixp4xx-regs.h header conflicts with the
on in the pxa27x device driver when compile-testing that:
In file included from ../drivers/usb/gadget/udc/pxa27x_udc.c:37:0:
../drivers/usb/gadget/udc/pxa27x_udc.h:26:0: warning: "UDCCR" redefined
#define UDCCR 0x0000 /* UDC Control Register */
^
In file included from ../arch/arm/mach-ixp4xx/include/mach/hardware.h:27:0,
from ../arch/arm/mach-ixp4xx/include/mach/io.h:18,
from ../arch/arm/include/asm/io.h:194,
from ../include/linux/io.h:25,
from ../include/linux/irq.h:24,
from ../drivers/usb/gadget/udc/pxa27x_udc.c:23:
../arch/arm/mach-ixp4xx/include/mach/ixp4xx-regs.h:415:0: note: this is the location of the previous definition
#define UDCCR IXP4XX_USB_REG(IXP4XX_USB_BASE_VIRT+0x0000)
This addresses both issues by moving all the definitions into the
pxa25x_udc driver itself. It turns out the only difference between
them was 'UDCCS_IO_ROF', and that could well be a mistake when it
was incorrectly copied from pxa25x to ixp4xx.
Acked-by: Krzysztof Halasa <khalasa@piap.pl>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
|
|
Drop support for platform data passed via a C-structure and switch to
device properties instead, which should make the driver compatible with all
platforms: OF, ACPI and static boards. Static boards should use property
sets to communicate device parameters to the driver.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Instead of using old GPIO API, let's switch to GPIOD API, which
automatically handles polarity.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Declare the number of DMA requestor lines per platform :
- for pxa25x: 40 requestor lines
- for pxa27x: 75 requestor lines
- for pxa3xx: 100 requestor lines
This information will be used to activate the DMA flow control or not.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
|
|
Clocks, timer and several other drivers have well defined and working
device-tree bindings. Clean-up the code to leave only the strict
minimum. The final goal will be to remove the lookup array.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
|
|
Bluetooth is only supported when network support is part of the kernel,
so it is a bit pointless to build the tosa-bt support without networking.
If we try anyway, we get a Kconfig warning:
warning: (TOSA_BT && H1940BT) selects RFKILL which has unmet direct dependencies (NET)
This adds a dependency on CONFIG_NET to avoid that case.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
|
|
When CONFIG_IWMMXT, the pxa3xx and pxa27x suspend/resume code
emits some xscale specific instructions, which are rejected
by the assembler, because gcc is built with -march=armv5
-mtune=xscale and passes that option to the assembler:
/tmp/cciHumzr.s:553: Error: selected processor does not support ARM mode `mra r2,r3,acc0'
/tmp/cciHumzr.s:605: Error: selected processor does not support ARM mode `mar acc0,r2,r3'
make[3]: *** [arch/arm/mach-pxa/pxa3xx.o] Error 1
/tmp/cci5MUNu.s:326: Error: selected processor does not support ARM mode `mra r2,r3,acc0'
/tmp/cci5MUNu.s:367: Error: selected processor does not support ARM mode `mar acc0,r2,r3'
make[3]: *** [arch/arm/mach-pxa/pxa27x.o] Error 1
Overriding with -Wa,-march=xscale no longer works, so instead
I'm adding an explict ".arch_extension" directive in all four inline
assembly statements, which should work even if they end up in a different
order in the assembly output.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
|
|
When CONFIG_IWMMXT is disabled, we get a warning in pxa3xx.c:
arch/arm/mach-pxa/pxa3xx.c: In function 'pxa3xx_cpu_pm_suspend':
arch/arm/mach-pxa/pxa3xx.c:109:2: error: ISO C90 forbids mixed declarations and code [-Werror=declaration-after-statement]
It turns out that there is an 'extern' declaration in the
middle of a function.
For consistency, this moves the declaration and two others from
the same file into pm.h.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
|
|
GPIO_SYSFS is a common kernel functionality, not something
that a board specific Kconfig should have to worry about.
In MIOA701, we get a warning about the select when CONFIG_SYSFS
is disabled:
warning: (MACH_MIOA701) selects GPIO_SYSFS which has unmet direct dependencies (GPIOLIB && SYSFS)
This just removes the select and instead enables the symbol in
the defconfig file.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
|
|
Two variables in eseries.c are used on multiple platforms,
but are not referenced when those are all disabled:
eseries.c:60:31: warning: 'e7xx_gpio_vbus' defined but not used [-Wunused-variable]
eseries.c:129:20: warning: 'eseries_register_clks' defined but not used [-Wunused-function]
Marking them __maybe_unused is the nicest way to ensure
that we never get the warning or end up with missing symbols
if we get it wrong.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
|
|
This function is only used when CONFIG_PCMCIA is enabled, otherwise
we get a harmless warning:
arch/arm/mach-pxa/spitz.c:204:13: warning: 'spitz_card_pwr_ctrl' defined but not used [-Wunused-function]
Marking it as __maybe_unused keeps the logic simple and avoids the
warning on randconfig builds.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
|
|
We should not dereference registers as pointers, so use readl/writel
instead for these registers.
The clock registers are accessed in multiple files, so we have to
change them all at once.
I stumbled over these registers while looking at something unrelated.
There are in fact other registers with the same problem, but I did
not try to address those at this point.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC multiplatform code updates from Arnd Bergmann:
"This branch is the culmination of 5 years of effort to bring the ARMv6
and ARMv7 platforms together such that they can all be enabled and
boot the same kernel. It has been a tremendous amount of cleanup and
refactoring by a huge number of people, and creation of several new
(and major) subsystems to better abstract out all the platform details
in an appropriate manner.
The bulk of this branch is a large patchset from Arnd that brings
several of the more minor and older platforms we have closer to
multiplatform support. Among these are MMP, S3C64xx, Orion5x, mv78xx0
and realview Much of this is moving around header files from old mach
directories, but there are also some cleanup patches of debug_ll
(lowlevel debug per-platform options) and other parts.
Linus Walleij also has some patchs to clean up the older ARM Realview
platforms by finally introducing DT support, and Rob Herring has some
for ARM Versatile which is now DT-only. Both of these platforms are
now multiplatform.
Finally, a couple of patches from Russell for Dove PMU, and a fix from
Valentin Rothberg for Exynos ADC, which were rebased on top of the
series to avoid conflicts"
* tag 'armsoc-multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (75 commits)
ARM: realview: don't select SMP_ON_UP for UP builds
ARM: s3c: simplify s3c_irqwake_{e,}intallow definition
ARM: s3c64xx: fix pm-debug compilation
iio: exynos-adc: fix irqf_oneshot.cocci warnings
ARM: realview: build realview-dt SMP support only when used
ARM: realview: select apropriate targets
ARM: realview: clean up header files
ARM: realview: make all header files local
ARM: no longer make CPU targets visible separately
ARM: integrator: use explicit core module options
ARM: realview: enable multiplatform
ARM: make default platform work for NOMMU
ARM: debug-ll: move DEBUG_LL_UART_EFM32 to correct Kconfig location
ARM: defconfig: use correct debug_ll settings
ARM: versatile: convert to multi-platform
ARM: versatile: merge mach code into a single file
ARM: versatile: switch to DT only booting and remove legacy code
ARM: versatile: add DT based PCI detection
ARM: pxa: mark ezx structures as __maybe_unused
ARM: pxa: mark raumfeld init functions as __maybe_unused
...
|
|
Pull MTD updates from Brian Norris:
"Generic MTD:
- populate the MTD device 'of_node' field (and get a proper 'of_node'
symlink in sysfs)
This yielded some new helper functions, and changes across a
variety of drivers
- partitioning cleanups, to prepare for better device-tree based
partitioning in the future
Eliminate a lot of boilerplate for drivers that want to use
OF-based partition parsing
The DT bindings for this didn't settle yet, so most non-cleanup
portions are deferred for a future release
NAND:
- embed a struct mtd_info inside struct nand_chip
This is really long overdue; too many drivers have to do the same
silly boilerplate to allocate and link up two "independent"
structs, when in fact, everyone is assuming there is an exact 1:1
relationship between a NAND chips struct and its underlying MTD.
This aids improved helpers and should make certain abstractions
easier in the future.
Also causes a lot of churn, helped along by some automated code
transformations
- add more core support for detecting (and "correcting") bitflips in
erased pages; requires opt-in by drivers, but at least we kill a
few bad implementations and hopefully stave off future ones
- pxa3xx_nand: cleanups, a few fixes, and PM improvements
- new JZ4780 NAND driver
SPI NOR:
- provide default erase function, for controllers that just want to
send the SECTOR_ERASE command directly
- fix some module auto-loading issues with device tree
("jedec,spi-nor")
- error handling fixes
- new Mediatek QSPI flash driver
Other:
- cfi: force valid geometry Kconfig (finally!)
This one used to trip up randconfigs occasionally, since bots
aren't deterred by big scary "advanced configuration" menus
More? Probably. See the commit logs"
* tag 'for-linus-20160112' of git://git.infradead.org/linux-mtd: (168 commits)
mtd: jz4780_nand: replace if/else blocks with switch/case
mtd: nand: jz4780: Update ecc correction error codes
mtd: nandsim: use nand_get_controller_data()
mtd: jz4780_nand: remove useless mtd->priv = chip assignment
staging: mt29f_spinand: make use of nand_set/get_controller_data() helpers
mtd: nand: make use of nand_set/get_controller_data() helpers
ARM: make use of nand_set/get_controller_data() helpers
mtd: nand: add helpers to access ->priv
mtd: nand: jz4780: driver for NAND devices on JZ4780 SoCs
mtd: nand: jz4740: remove custom 'erased check' implementation
mtd: nand: diskonchip: remove custom 'erased check' implementation
mtd: nand: davinci: remove custom 'erased check' implementation
mtd: nand: use nand_check_erased_ecc_chunk in default ECC read functions
mtd: nand: return consistent error codes in ecc.correct() implementations
doc: dt: mtd: new binding for jz4780-{nand,bch}
mtd: cfi_cmdset_0001: fixing memory leak and handling failed kmalloc
mtd: spi-nor: wait until lock/unlock operations are ready
mtd: tests: consolidate kmalloc/memset 0 call to kzalloc
jffs2: use to_delayed_work
mtd: nand: assign reasonable default name for NAND drivers
...
|
|
* patchwork: (204 commits)
[media] rc: sunxi-cir: Initialize the spinlock properly
[media] rtl2832: do not filter out slave TS null packets
[media] rtl2832: print reg number on error case
[media] rtl28xxu: return demod reg page from driver cache
[media] coda: enable MPEG-2 ES decoding
[media] coda: don't start streaming without queued buffers
[media] coda: hook up vidioc_prepare_buf
[media] coda: relax coda_jpeg_check_buffer for trailing bytes
[media] coda: make to_coda_video_device static
[media] s5p-mfc: remove volatile attribute from MFC register addresses
[media] s5p-mfc: merge together s5p_mfc_hw_call and s5p_mfc_hw_call_void
[media] s5p-mfc: use spinlock to protect MFC context
[media] s5p-mfc: remove unnecessary callbacks
[media] s5p-mfc: make queue cleanup code common
[media] s5p-mfc: use one implementation of s5p_mfc_get_new_ctx
[media] s5p-mfc: constify s5p_mfc_codec_ops structures
[media] au8522: Avoid memory leak for device config data
[media] ir-lirc-codec.c: don't leak lirc->drv-rbuf
[media] uvcvideo: small cleanup in uvc_video_clock_update()
[media] uvcvideo: Fix reading the current exposure value of UVC
...
|
|
The 'fixes' branch contains d5d4fdd86f57 ("irqchip/versatile-fpga:
Fix PCI IRQ mapping on Versatile PB") that is required for booting
the versatile platform prior to the rework in this branch, but
including both causes a build-time error.
I'm doing an evil merge here to pull in the fixes branch so we have
that commit included but at the same time revert the trivial change.
This gives us a bisectable history.
* fixes: (22 commits)
fsl-ifc: add missing include on ARM64
ls2080a/dts: Add little endian property for GPIO IP block
dt-bindings: define little-endian property for QorIQ GPIO
ARM64: dts: ls2080a: fix eSDHC endianness
ARM: dts: vf610: use reset values for L2 cache latencies
ARM: pxa: use PWM lookup table for all machines
ARM: dts: berlin: add 2nd clock for BG2Q sdhci0 and sdhci1
ARM: dts: berlin: correct BG2Q's sdhci2 2nd clock
ARM: dts: am4372: fix clock source for arm twd and global timers
ARM: at91: fix pinctrl driver selection
ARM: at91/dt: add always-on to 1.8V regulator
ARM: dts: vf610: fix clock definition for SAI2
ARM: imx: clk-vf610: fix SAI clock tree
ARM: ixp4xx: fix read{b,w,l} return types
irqchip/versatile-fpga: Fix PCI IRQ mapping on Versatile PB
ARM: OMAP2+: enable REGULATOR_FIXED_VOLTAGE
ARM: dts: add dm816x missing spi DT dma handles
ARM: dts: add dm816x missing #mbox-cells
cpufreq: s3c24xx: Do not mark s3c2410_plls_add as __init
bus: sunxi-rsb: unlock on error in sunxi_rsb_read()
...
|
|
The ezx platform contains multiple machine descriptors, but not all
of them use all of the data structures, and it's possible to disable
all of the machines, which produces some harmless warnings:
mach-pxa/ezx.c:53:26: warning: 'ezx_pwm_lookup' defined but not used [-Wunused-variable]
mach-pxa/ezx.c:86:31: warning: 'ezx_fb_info_1' defined but not used [-Wunused-variable]
mach-pxa/ezx.c:107:31: warning: 'ezx_fb_info_2' defined but not used [-Wunused-variable]
mach-pxa/ezx.c:113:32: warning: 'ezx_devices' defined but not used [-Wunused-variable]
mach-pxa/ezx.c:117:22: warning: 'ezx_pin_config' defined but not used [-Wunused-variable]
This marks all those structures as __maybe_unused to avoid the warnings.
Obviously a configuration that contains the ezx platform but no specific
model is a bit silly, but it should not cause compile-time warnings.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
|
|
The raumfeld.c file contains three similar machine definitions,
each with their own init function. If one or more of them are
disabled, we get compile-time warnings:
arm/mach-pxa/raumfeld.c:1070:123: warning: 'raumfeld_connector_init' defined but not used [-Wunused-function]
arm/mach-pxa/raumfeld.c:1082:123: warning: 'raumfeld_speaker_init' defined but not used [-Wunused-function]
This marks the functions as __maybe_unused to avoid the warnings.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Daniel Mack <daniel@zonque.org>
|
|
In an old commit, we worked around the duplicate definition of
GPIO24_SSP1_SFRM in cm-x2xx.c, which includes files for both
pxa25x and pxa27x. Apparently the problem has come back and we
now have four additional duplicate symbols that cause warnings:
In file included from /git/arm-soc/arch/arm/mach-pxa/pxa27x.h:7:0,
from /git/arm-soc/arch/arm/mach-pxa/cm-x2xx.c:27:
/git/arm-soc/arch/arm/mach-pxa/mfp-pxa27x.h:21:0: warning: "GPIO86_GPIO" redefined
#define GPIO86_GPIO MFP_CFG_IN(GPIO86, AF0)
This uses the same hack as before and undefines all symbols that
are defined more than once. Fortunately, cm-x2xx does not need
any of these.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
|
|
The recent change to use a pwm lookup table for the ezx machines
was incomplete and only changed the a780 model, but not the
other ones in the same file.
This adds the missing calls to pwm_add_table().
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: c3322022897c ("ARM: pxa: ezx: Use PWM lookup table")
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
|
|
mtd_to_nand() was recently introduced to avoid direct accesses to the
mtd->priv field. Update all ARM specific implementations to use this
helper.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
|
Lots of header files are never included outside of a mach-pxa
directory and do not need to be made visible in include/mach,
so let's just move them all down one level.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The patches that were applied to add PWM lookup tables for legacy boards
were from v1 of the series instead of the revised v2 where the resulting
build errors had already been fixed.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Now that media has its own subdirectory inside platform_data,
let's move the headers that are already there to such subdir.
After moving those files, the references were adjusted using this
script:
MAIN_DIR="linux/platform_data/"
PREV_DIR="linux/platform_data/"
DIRS="media/"
echo "Checking affected files" >&2
for i in $DIRS; do
for j in $(find include/$MAIN_DIR/$i -type f -name '*.h'); do
n=`basename $j`
git grep -l $n
done
done|sort|uniq >files && (
echo "Handling files..." >&2;
echo "for i in \$(cat files|grep -v Documentation); do cat \$i | \\";
(
cd include/$MAIN_DIR;
for j in $DIRS; do
for i in $(ls $j); do
echo "perl -ne 's,(include [\\\"\\<])$PREV_DIR($i)([\\\"\\>]),\1$MAIN_DIR$j\2\3,; print \$_' |\\";
done;
done;
echo "cat > a && mv a \$i; done";
);
echo "Handling documentation..." >&2;
echo "for i in MAINTAINERS \$(cat files); do cat \$i | \\";
(
cd include/$MAIN_DIR;
for j in $DIRS; do
for i in $(ls $j); do
echo " perl -ne 's,include/$PREV_DIR($i)\b,include/$MAIN_DIR$j\1,; print \$_' |\\";
done;
done;
echo "cat > a && mv a \$i; done"
);
) >script && . ./script
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Currently, include/media is messy, as it contains both the V4L2 core
headers and some driver-specific headers on the same place. That makes
harder to identify what core headers should be documented and what
headers belong to I2C drivers that are included only by bridge/main
drivers that would require the functions provided by them.
Let's move those i2c specific files to its own subdirectory.
The files to move were produced via the following script:
mkdir include/media/i2c
(cd include/media; for i in *.h; do n=`echo $i|sed s/.h$/.c/`; if [ -e ../../drivers/media/i2c/$n ]; then echo $i; git mv $i i2c/; fi; done)
(cd include/media; for i in *.h; do n=`echo $i|sed s/.h$/.c/`; if [ -e ../../drivers/media/*/i2c/$n ]; then echo $i; git mv $i i2c/; fi; done)
for i in include/media/*.h; do n=`basename $i`; (for j in $(git grep -l $n); do dirname $j; done)|sort|uniq|grep -ve '^.$' > list; num=$(wc -l list|cut -d' ' -f1); if [ $num == 1 ]; then if [ "`grep i2c list`" != "" ]; then git mv $i include/media/i2c; fi; fi; done
And the references corrected via this script:
MAIN_DIR="media/"
PREV_DIR="media/"
DIRS="i2c/"
echo "Checking affected files" >&2
for i in $DIRS; do
for j in $(find include/$MAIN_DIR/$i -type f -name '*.h'); do
n=`basename $j`
git grep -l $n
done
done|sort|uniq >files && (
echo "Handling files..." >&2;
echo "for i in \$(cat files|grep -v Documentation); do cat \$i | \\";
(
cd include/$MAIN_DIR;
for j in $DIRS; do
for i in $(ls $j); do
echo "perl -ne 's,(include [\\\"\\<])$PREV_DIR($i)([\\\"\\>]),\1$MAIN_DIR$j\2\3,; print \$_' |\\";
done;
done;
echo "cat > a && mv a \$i; done";
);
echo "Handling documentation..." >&2;
echo "for i in MAINTAINERS \$(cat files); do cat \$i | \\";
(
cd include/$MAIN_DIR;
for j in $DIRS; do
for i in $(ls $j); do
echo " perl -ne 's,include/$PREV_DIR($i)\b,include/$MAIN_DIR$j\1,; print \$_' |\\";
done;
done;
echo "cat > a && mv a \$i; done"
);
) >script && . ./script
Merged Sakari Ailus patch that moves smiapp.h to include/media/i2c.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Olof Johansson:
"Again we have a sizable (but not huge) cleanup branch with a net delta
of about -3k lines.
Main contents here is:
- A bunch of development/cleanup of a few PXA boards
- Removal of bockw platforms on shmobile, since the platform has now
gone completely multiplatform. Whee!
- move of the 32kHz timer on OMAP to a proper timesource
- Misc cleanup of older OMAP material (incl removal of one board
file)
- Switch over to new common PWM lookup support for several platforms
There's also a handful of other cleanups across the tree, but the
above are the major pieces"
* tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (103 commits)
ARM: OMAP3: hwmod data: Remove legacy mailbox data and addrs
ARM: DRA7: hwmod data: Remove spinlock hwmod addrs
ARM: OMAP4: hwmod data: Remove spinlock hwmod addrs
ARM: DRA7/AM335x/AM437x: hwmod: Remove gpmc address space from hwmod data
ARM: Remove __ref on hotplug cpu die path
ARM: Remove open-coded version of IRQCHIP_DECLARE
arm: omap2: board-generic: use omap4_local_timer_init for AM437x
ARM: DRA7/AM335x/AM437x: hwmod: Remove elm address space from hwmod data
ARM: OMAP: Remove duplicated operand in OR operation
clocksource: ti-32k: make it depend on GENERIC_CLOCKSOURCE
ARM: pxa: remove incorrect __init annotation on pxa27x_set_pwrmode
ARM: pxa: raumfeld: make some variables static
ARM: OMAP: Change all cpu_is_* occurences to soc_is_* for id.c
ARM: OMAP2+: Rename cpu_is macros to soc_is
arm: omap2: timer: limit hwmod usage to non-DT boots
arm: omap2+: select 32k clocksource driver
clocksource: add TI 32.768 Hz counter driver
arm: omap2: timer: rename omap_sync32k_timer_init()
arm: omap2: timer: always call clocksource_of_init() when DT
arm: omap2: timer: move realtime_counter_init() around
...
|
|
This is the pxa changes for v4.4 cycle.
This cycle is bigger than usual :
- magician was greatly enhanced (new IPs discovered, ...)
- almost all legacy board files have been updated to the
new PWM API (mostly for backlight control)
- some minor fixes in raumfeld, z2 and mioa701
* tag 'pxa-for-4.4' of https://github.com/rjarzmik/linux: (44 commits)
ARM: pxa: remove incorrect __init annotation on pxa27x_set_pwrmode
ARM: pxa: raumfeld: make some variables static
ARM: pxa: magician: Remove pdata for pasic3-leds
ARM: pxa: magician: Add support for PXA27x UDC
ARM: pxa: magician: Add support for MAX1587A Vcore regulator
ARM: pxa: magician: Change comments to be more informative
ARM: pxa: magician: Move platform_add_devices() to the end of magician_init()
ARM: pxa: magician: Add missing regulator for PWM backlight
ARM: pxa: magician: Add debug message for backlight brightness function
ARM: pxa: magician: Remove definition of the STUART port
ARM: pxa: magician: Fix wrongly enabled USB host ports
ARM: pxa: magician: Fix support for Intel Strata NOR Flash
ARM: pxa: magician: Fix redundant GPIO request for pxaficp_ir
ARM: pxa: magician: Fix platform data for both PXA27x I2C controllers
ARM: pxa: magician: Fix and add charging detection functions
ARM: pxa: magician: Optimize Samsung LCD refresh to 50Hz
ARM: pxa: magician: Rename charger cable detection EGPIOs
ARM: pxa: magician: Optimize powerup delays for Samsung LCD
ARM: pxa: magician: Rename abstract LCD GPIOs
ARM: pxa: magician: Add new discovered EGPIO pins
...
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
The z2 machine calls pxa27x_set_pwrmode() in order to power off
the machine, but this function gets discarded early at boot because
it is marked __init, as pointed out by kbuild:
WARNING: vmlinux.o(.text+0x145c4): Section mismatch in reference from the function z2_power_off() to the function .init.text:pxa27x_set_pwrmode()
The function z2_power_off() references
the function __init pxa27x_set_pwrmode().
This is often because z2_power_off lacks a __init
annotation or the annotation of pxa27x_set_pwrmode is wrong.
This removes the __init section modifier to fix rebooting and the
build error.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: ba4a90a6d86a ("ARM: pxa/z2: fix building error of pxa27x_cpu_suspend() no longer available")
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
|
|
This fixes the following sparse warnings:
arch/arm/mach-pxa/raumfeld.c:510:24: warning: symbol 'raumfeld_w1_gpio_device' was not declared. Should it be static?
arch/arm/mach-pxa/raumfeld.c:632:31: warning: symbol 'raumfeld_spi_platform_data' was not declared. Should it be static?
arch/arm/mach-pxa/raumfeld.c:851:28: warning: symbol 'audio_va_initdata' was not declared. Should it be static?
arch/arm/mach-pxa/raumfeld.c:883:28: warning: symbol 'audio_dummy_initdata' was not declared. Should it be static?
arch/arm/mach-pxa/raumfeld.c:931:28: warning: symbol 'max8660_v6_subdev_data' was not declared. Should it be static?
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
|
|
The pasic3-leds driver was never in vanilla kernel. Actual configuration
data for a hypothetical driver does not describe hardware completely, so
remove them.
This patch prepare HTC Magician machine code to pasic3-leds driver
addition.
Signed-off-by: Petr Cvek <petr.cvek@tul.cz>
Acked-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
|
|
A PXA27x SoC supports USB device mode, this patch adds support for that.
Signed-off-by: Petr Cvek <petr.cvek@tul.cz>
Acked-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
|
|
HTC Magician contains a MAX1587A voltage regulator for a Vcore supply.
The Vcore regulation is required for a CPU speed switching. This patch adds
declaration for the max1586 driver.
Notice:
- MAX1587A version does not support the V6 (USIM) output.
- A boost resistor was directly measured for a board_id 0x3a.
Signed-off-by: Petr Cvek <petr.cvek@tul.cz>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
|
|
This patch changes the comments in the HTC Magician machine source code
to better describe used devices and interfaces.
Signed-off-by: Petr Cvek <petr.cvek@tul.cz>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
|
|
This patch moves platform_add_devices() (standard declaration of devices)
outside of the platform specific device declarations. Moving to the end
of the magician_init() clarifies the source code (standard and specific
declaration are not mixed).
Signed-off-by: Petr Cvek <petr.cvek@tul.cz>
Acked-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
|
|
Add a fake regulator, which is required for the correct initialization
of the PWM backlight driver.
Signed-off-by: Petr Cvek <petr.cvek@tul.cz>
Acked-by: Philipp Zabel <philipp.zabel@gmail.com>
[ added a missing include for fixed regulator ]
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
|
|
Add a debug message for the backlight brightness function.
Signed-off-by: Petr Cvek <petr.cvek@tul.cz>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
|
|
Magician STUART port is connected to the infraport and used by the FICP
driver. The FICP driver uses its own definition.
Required for correct initialization of the pxaficp_ir driver after
planned dmaengine conversion.
Signed-off-by: Petr Cvek <petr.cvek@tul.cz>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
|
