| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
dm365 have only single McBSP, so the device name is without .0
Fixes: 0c750e1fe481d ("ARM: davinci: dm365: Add dma_slave_map to edma")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"This contains driver changes that are tightly connected to SoC
specific code. Aside from smaller cleanups and bug fixes, here is a
list of the notable changes.
New device drivers:
- The Turris Mox router has a new "moxtet" bus driver for its
on-board pluggable extension bus. The same platform also gains a
firmware driver.
- The Samsung Exynos family gains a new Chipid driver exporting using
the soc device sysfs interface
- A similar socinfo driver for Qualcomm Snapdragon chips.
- A firmware driver for the NXP i.MX DSP IPC protocol using shared
memory and a mailbox
Other changes:
- The i.MX reset controller driver now supports the NXP i.MX8MM chip
- Amlogic SoC specific drivers gain support for the S905X3 and A311D
chips
- A rework of the TI Davinci framebuffer driver to allow important
cleanups in the platform code
- A couple of device drivers for removed ARM SoC platforms are
removed. Most of the removals were picked up by other maintainers,
this contains whatever was left"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (123 commits)
bus: uniphier-system-bus: use devm_platform_ioremap_resource()
soc: ti: ti_sci_pm_domains: Add support for exclusive and shared access
dt-bindings: ti_sci_pm_domains: Add support for exclusive and shared access
firmware: ti_sci: Allow for device shared and exclusive requests
bus: imx-weim: remove incorrect __init annotations
fbdev: remove w90x900/nuc900 platform drivers
spi: remove w90x900 driver
net: remove w90p910-ether driver
net: remove ks8695 driver
firmware: turris-mox-rwtm: Add sysfs documentation
firmware: Add Turris Mox rWTM firmware driver
dt-bindings: firmware: Document cznic,turris-mox-rwtm binding
bus: moxtet: fix unsigned comparison to less than zero
bus: moxtet: remove set but not used variable 'dummy'
ARM: scoop: Use the right include
dt-bindings: power: add Amlogic Everything-Else power domains bindings
soc: amlogic: Add support for Everything-Else power domains controller
fbdev: da8xx: use resource management for dma
fbdev: da8xx-fb: drop a redundant if
fbdev: da8xx-fb: use devm_platform_ioremap_resource()
...
|
|
Add modifications necessary to make davinci part of the ARM v5
multiplatform build.
Move the arch-specific configuration out of arch/arm/Kconfig and
into mach-davinci/Kconfig. Remove the sub-menu for DaVinci
implementations (they'll be visible directly under the system type.
Select all necessary options not already selected by ARCH_MULTI_V5.
Update davinci_all_defconfig. Explicitly include the mach-specific
headers in mach-davinci/Makefile.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into arm/soc
This converts all DaVinci SoCs except DM365 to use new clocksource
driver. DM365 conversion is still under debug and will be part of a
future pull request.
* tag 'davinci-for-v5.4/soc' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: davinci: dm646x: Fix a typo in the comment
ARM: davinci: dm646x: switch to using the clocksource driver
ARM: davinci: dm644x: switch to using the clocksource driver
ARM: davinci: dm355: switch to using the clocksource driver
ARM: davinci: move timer definitions to davinci.h
ARM: davinci: da830: switch to using the clocksource driver
ARM: davinci: da850: switch to using the clocksource driver
ARM: davinci: WARN_ON() if clk_get() fails
ARM: davinci: enable the clocksource driver for DT mode
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Now that the da8xx fbdev driver supports power control with an actual
regulator, switch to using a fixed power supply for da850-evm.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
Instead of enabling the panel backlight in a callback defined in board
file using deprecated legacy GPIO API calls, model the line as a GPIO
backlight device.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
The driver is dedicated to DM646x. So update the description in the top
most comment accordingly.
It must have been derived from dm644x.c, but looks DM646 speecific now.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
We now have a proper clocksource driver for davinci. Switch the dm646x
platform to using it.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: David Lechner <david@lechnology.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
We now have a proper clocksource driver for davinci. Switch the dm644x
platform to using it.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: David Lechner <david@lechnology.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
We now have a proper clocksource driver for davinci. Switch the dm355
platform to using it.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: David Lechner <david@lechnology.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
Boards from the dm* family rely on register offset definitions from
arch/arm/mach-davinci/include/mach/time.h. We'll be removing this file
soon, so move the required defines to davinci.h where the rest of such
constants live.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: David Lechner <david@lechnology.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
We now have a proper clocksource driver for davinci. Switch the da830
platform to using it.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: David Lechner <david@lechnology.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
We now have a proper clocksource driver for davinci. Switch the da850
platform to using it.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: David Lechner <david@lechnology.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
Currently the timer code checks if the clock pointer passed to it is
good (!IS_ERR(clk)). The new clocksource driver expects the clock to
be functional and doesn't perform any checks so emit a warning if
clk_get() fails. Apply this to all davinci platforms.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: David Lechner <david@lechnology.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
Switch all davinci boards supporting device tree to using the new
clocksource driver: remove the previous OF_TIMER_DECLARE() from
mach-davinci and select davinci-timer for ARCH_DAVINCI.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: David Lechner <david@lechnology.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
When building a multiplatform kernel that includes armv4 support,
the default target CPU does not support the blx instruction,
which leads to a build failure:
arch/arm/mach-davinci/sleep.S: Assembler messages:
arch/arm/mach-davinci/sleep.S:56: Error: selected processor does not support `blx ip' in ARM mode
Add a .arch statement in the sources to make this file build.
Link: https://lore.kernel.org/r/20190722145211.1154785-1-arnd@arndb.de
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Pull ARM SoC platform updates from Olof Johansson:
"SoC platform changes. Main theme this merge window:
- The Netx platform (Netx 100/500) platform is removed by Linus
Walleij-- the SoC doesn't have active maintainers with hardware,
and in discussions with the vendor the agreement was that it's OK
to remove.
- Russell King has a series of patches that cleans up and refactors
SA1101 and RiscPC support"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (47 commits)
ARM: stm32: use "depends on" instead of "if" after prompt
ARM: sa1100: convert to common clock framework
ARM: exynos: Cleanup cppcheck shifting warning
ARM: pxa/lubbock: remove lubbock_set_misc_wr() from global view
ARM: exynos: Only build MCPM support if used
arm: add missing include platform-data/atmel.h
ARM: davinci: Use GPIO lookup table for DA850 LEDs
ARM: OMAP2: drop explicit assembler architecture
ARM: use arch_extension directive instead of arch argument
ARM: imx: Switch imx7d to imx-cpufreq-dt for speed-grading
ARM: bcm: Enable PINCTRL for ARCH_BRCMSTB
ARM: bcm: Enable ARCH_HAS_RESET_CONTROLLER for ARCH_BRCMSTB
ARM: riscpc: enable chained scatterlist support
ARM: riscpc: reduce IRQ handling code
ARM: riscpc: move RiscPC assembly files from arch/arm/lib to mach-rpc
ARM: riscpc: parse video information from tagged list
ARM: riscpc: add ecard quirk for Atomwide 3port serial card
MAINTAINERS: mvebu: Add git entry
soc: ti: pm33xx: Add a print while entering RTC only mode with DDR in self-refresh
ARM: OMAP2+: Make some variables static
...
|
|
The fixed regulator driver doesn't specify any con_id for gpio lookup
so it must be NULL in the table entry.
Fixes: 274e4c336192 ("ARM: davinci: da830-evm: add a fixed regulator for ohci-da8xx")
Cc: stable@vger.kernel.org
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
We need to enable status changes for the fixed power supply for the USB
controller.
Fixes: 1d272894ec4f ("ARM: davinci: omapl138-hawk: add a fixed regulator for ohci-da8xx")
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
We need to enable status changes for the fixed power supply for the USB
controller.
Fixes: 274e4c336192 ("ARM: davinci: da830-evm: add a fixed regulator for ohci-da8xx")
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into arm/soc
This pull request has a patch to switch DA850 EVM GPIO LED support to use
GPIO lookup table
* tag 'davinci-for-v5.3/soc' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: davinci: Use GPIO lookup table for DA850 LEDs
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx
Pull still more SPDX updates from Greg KH:
"Another round of SPDX updates for 5.2-rc6
Here is what I am guessing is going to be the last "big" SPDX update
for 5.2. It contains all of the remaining GPLv2 and GPLv2+ updates
that were "easy" to determine by pattern matching. The ones after this
are going to be a bit more difficult and the people on the spdx list
will be discussing them on a case-by-case basis now.
Another 5000+ files are fixed up, so our overall totals are:
Files checked: 64545
Files with SPDX: 45529
Compared to the 5.1 kernel which was:
Files checked: 63848
Files with SPDX: 22576
This is a huge improvement.
Also, we deleted another 20000 lines of boilerplate license crud,
always nice to see in a diffstat"
* tag 'spdx-5.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx: (65 commits)
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 507
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 506
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 505
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 504
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 503
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 502
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 501
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 500
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 499
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 498
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 497
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 496
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 495
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 491
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 490
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 489
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 488
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 487
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 486
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 485
...
|
|
This switches the DA850 board to use a GPIO lookup table to
look up the GPIO LEDs. Thanks to the offset handling when
we define GPIOs as an offset into the chip, we can drop
some complex code.
Tested-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into fixes
DaVinci fixes for v5.2 kernel.
This addresses an issue with probe of IO expander on DA850 EVM. There is
also a WARN_ON() fix on DA850 and DA830 devices.
* tag 'davinci-fixes-for-v5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: davinci: da8xx: specify dma_coherent_mask for lcdc
ARM: davinci: da850-evm: call regulator_has_full_constraints()
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
The lcdc device is missing the dma_coherent_mask definition causing the
following warning on da850-evm:
da8xx_lcdc da8xx_lcdc.0: found Sharp_LK043T1DG01 panel
------------[ cut here ]------------
WARNING: CPU: 0 PID: 1 at kernel/dma/mapping.c:247 dma_alloc_attrs+0xc8/0x110
Modules linked in:
CPU: 0 PID: 1 Comm: swapper Not tainted 5.2.0-rc3-00077-g16d72dd4891f #18
Hardware name: DaVinci DA850/OMAP-L138/AM18x EVM
[<c000fce8>] (unwind_backtrace) from [<c000d900>] (show_stack+0x10/0x14)
[<c000d900>] (show_stack) from [<c001a4f8>] (__warn+0xec/0x114)
[<c001a4f8>] (__warn) from [<c001a634>] (warn_slowpath_null+0x3c/0x48)
[<c001a634>] (warn_slowpath_null) from [<c0065860>] (dma_alloc_attrs+0xc8/0x110)
[<c0065860>] (dma_alloc_attrs) from [<c02820f8>] (fb_probe+0x228/0x5a8)
[<c02820f8>] (fb_probe) from [<c02d3e9c>] (platform_drv_probe+0x48/0x9c)
[<c02d3e9c>] (platform_drv_probe) from [<c02d221c>] (really_probe+0x1d8/0x2d4)
[<c02d221c>] (really_probe) from [<c02d2474>] (driver_probe_device+0x5c/0x168)
[<c02d2474>] (driver_probe_device) from [<c02d2728>] (device_driver_attach+0x58/0x60)
[<c02d2728>] (device_driver_attach) from [<c02d27b0>] (__driver_attach+0x80/0xbc)
[<c02d27b0>] (__driver_attach) from [<c02d047c>] (bus_for_each_dev+0x64/0xb4)
[<c02d047c>] (bus_for_each_dev) from [<c02d1590>] (bus_add_driver+0xe4/0x1d8)
[<c02d1590>] (bus_add_driver) from [<c02d301c>] (driver_register+0x78/0x10c)
[<c02d301c>] (driver_register) from [<c000a5c0>] (do_one_initcall+0x48/0x1bc)
[<c000a5c0>] (do_one_initcall) from [<c05cae6c>] (kernel_init_freeable+0x10c/0x1d8)
[<c05cae6c>] (kernel_init_freeable) from [<c048a000>] (kernel_init+0x8/0xf4)
[<c048a000>] (kernel_init) from [<c00090e0>] (ret_from_fork+0x14/0x34)
Exception stack(0xc6837fb0 to 0xc6837ff8)
7fa0: 00000000 00000000 00000000 00000000
7fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
7fe0: 00000000 00000000 00000000 00000000 00000013 00000000
---[ end trace 8a8073511be81dd2 ]---
Add a 32-bit mask to the platform device's definition.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
The BB expander at 0x21 i2c bus 1 fails to probe on da850-evm because
the board doesn't set has_full_constraints to true in the regulator
API.
Call regulator_has_full_constraints() at the end of board registration
just like we do in da850-lcdk and da830-evm.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not write to the free
software foundation inc 59 temple place suite 330 boston ma 02111
1307 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 136 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190530000436.384967451@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program if not write to the free software foundation inc
675 mass ave cambridge ma 02139 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 441 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc)
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190520071858.739733335@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull more clk framework updates from Stephen Boyd:
"One more patch to remove io.h from clk-provider.h.
We used to need this include when we had clk_readl() and clk_writel(),
but those are gone now so this patch pushes the dependency out to the
users of clk-provider.h"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: Remove io.h from clk-provider.h
|
|
Now that we've gotten rid of clk_readl() we can remove io.h from the
clk-provider header and push out the io.h include to any code that isn't
already including the io.h header but using things like readl/writel,
etc.
Found with this grep:
git grep -l clk-provider.h | grep '.c$' | xargs git grep -L 'linux/io.h' | \
xargs git grep -l \
-e '\<__iowrite32_copy\>' --or \
-e '\<__ioread32_copy\>' --or \
-e '\<__iowrite64_copy\>' --or \
-e '\<ioremap_page_range\>' --or \
-e '\<ioremap_huge_init\>' --or \
-e '\<arch_ioremap_pud_supported\>' --or \
-e '\<arch_ioremap_pmd_supported\>' --or \
-e '\<devm_ioport_map\>' --or \
-e '\<devm_ioport_unmap\>' --or \
-e '\<IOMEM_ERR_PTR\>' --or \
-e '\<devm_ioremap\>' --or \
-e '\<devm_ioremap_nocache\>' --or \
-e '\<devm_ioremap_wc\>' --or \
-e '\<devm_iounmap\>' --or \
-e '\<devm_ioremap_release\>' --or \
-e '\<devm_memremap\>' --or \
-e '\<devm_memunmap\>' --or \
-e '\<__devm_memremap_pages\>' --or \
-e '\<pci_remap_cfgspace\>' --or \
-e '\<arch_has_dev_port\>' --or \
-e '\<arch_phys_wc_add\>' --or \
-e '\<arch_phys_wc_del\>' --or \
-e '\<memremap\>' --or \
-e '\<memunmap\>' --or \
-e '\<arch_io_reserve_memtype_wc\>' --or \
-e '\<arch_io_free_memtype_wc\>' --or \
-e '\<__io_aw\>' --or \
-e '\<__io_pbw\>' --or \
-e '\<__io_paw\>' --or \
-e '\<__io_pbr\>' --or \
-e '\<__io_par\>' --or \
-e '\<__raw_readb\>' --or \
-e '\<__raw_readw\>' --or \
-e '\<__raw_readl\>' --or \
-e '\<__raw_readq\>' --or \
-e '\<__raw_writeb\>' --or \
-e '\<__raw_writew\>' --or \
-e '\<__raw_writel\>' --or \
-e '\<__raw_writeq\>' --or \
-e '\<readb\>' --or \
-e '\<readw\>' --or \
-e '\<readl\>' --or \
-e '\<readq\>' --or \
-e '\<writeb\>' --or \
-e '\<writew\>' --or \
-e '\<writel\>' --or \
-e '\<writeq\>' --or \
-e '\<readb_relaxed\>' --or \
-e '\<readw_relaxed\>' --or \
-e '\<readl_relaxed\>' --or \
-e '\<readq_relaxed\>' --or \
-e '\<writeb_relaxed\>' --or \
-e '\<writew_relaxed\>' --or \
-e '\<writel_relaxed\>' --or \
-e '\<writeq_relaxed\>' --or \
-e '\<readsb\>' --or \
-e '\<readsw\>' --or \
-e '\<readsl\>' --or \
-e '\<readsq\>' --or \
-e '\<writesb\>' --or \
-e '\<writesw\>' --or \
-e '\<writesl\>' --or \
-e '\<writesq\>' --or \
-e '\<inb\>' --or \
-e '\<inw\>' --or \
-e '\<inl\>' --or \
-e '\<outb\>' --or \
-e '\<outw\>' --or \
-e '\<outl\>' --or \
-e '\<inb_p\>' --or \
-e '\<inw_p\>' --or \
-e '\<inl_p\>' --or \
-e '\<outb_p\>' --or \
-e '\<outw_p\>' --or \
-e '\<outl_p\>' --or \
-e '\<insb\>' --or \
-e '\<insw\>' --or \
-e '\<insl\>' --or \
-e '\<outsb\>' --or \
-e '\<outsw\>' --or \
-e '\<outsl\>' --or \
-e '\<insb_p\>' --or \
-e '\<insw_p\>' --or \
-e '\<insl_p\>' --or \
-e '\<outsb_p\>' --or \
-e '\<outsw_p\>' --or \
-e '\<outsl_p\>' --or \
-e '\<ioread8\>' --or \
-e '\<ioread16\>' --or \
-e '\<ioread32\>' --or \
-e '\<ioread64\>' --or \
-e '\<iowrite8\>' --or \
-e '\<iowrite16\>' --or \
-e '\<iowrite32\>' --or \
-e '\<iowrite64\>' --or \
-e '\<ioread16be\>' --or \
-e '\<ioread32be\>' --or \
-e '\<ioread64be\>' --or \
-e '\<iowrite16be\>' --or \
-e '\<iowrite32be\>' --or \
-e '\<iowrite64be\>' --or \
-e '\<ioread8_rep\>' --or \
-e '\<ioread16_rep\>' --or \
-e '\<ioread32_rep\>' --or \
-e '\<ioread64_rep\>' --or \
-e '\<iowrite8_rep\>' --or \
-e '\<iowrite16_rep\>' --or \
-e '\<iowrite32_rep\>' --or \
-e '\<iowrite64_rep\>' --or \
-e '\<__io_virt\>' --or \
-e '\<pci_iounmap\>' --or \
-e '\<virt_to_phys\>' --or \
-e '\<phys_to_virt\>' --or \
-e '\<ioremap_uc\>' --or \
-e '\<ioremap\>' --or \
-e '\<__ioremap\>' --or \
-e '\<iounmap\>' --or \
-e '\<ioremap\>' --or \
-e '\<ioremap_nocache\>' --or \
-e '\<ioremap_uc\>' --or \
-e '\<ioremap_wc\>' --or \
-e '\<ioremap_wc\>' --or \
-e '\<ioremap_wt\>' --or \
-e '\<ioport_map\>' --or \
-e '\<ioport_unmap\>' --or \
-e '\<ioport_map\>' --or \
-e '\<ioport_unmap\>' --or \
-e '\<xlate_dev_kmem_ptr\>' --or \
-e '\<xlate_dev_mem_ptr\>' --or \
-e '\<unxlate_dev_mem_ptr\>' --or \
-e '\<virt_to_bus\>' --or \
-e '\<bus_to_virt\>' --or \
-e '\<memset_io\>' --or \
-e '\<memcpy_fromio\>' --or \
-e '\<memcpy_toio\>'
I also reordered a couple includes when they weren't alphabetical and
removed clk.h from kona, replacing it with clk-provider.h because
that driver doesn't use clk consumer APIs.
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Mark Brown <broonie@kernel.org>
Cc: Chris Zankel <chris@zankel.net>
Acked-by: Max Filippov <jcmvbkbc@gmail.com>
Acked-by: John Crispin <john@phrozen.org>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Instead of directly using the vbus GPIO we should model it as a fixed
regulator. Add all necessary fix-ups for the regulator to be registered
and configure the vbus GPIO as its enable pin.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
Instead of directly using the vbus GPIO we should model it as a fixed
regulator. Add all necessary fix-ups for the regulator to be registered
and configure the vbus GPIO as its enable pin.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
Some GPIO lookup tables defined in davinci board files are missing
array sentinels. If an entry for given device cannot be found, this
will cause a kernel panic.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"These are PM-runtime framework changes to use ktime instead of jiffies
for accounting, new PM core flag to mark devices that don't need any
form of power management, cpuidle updates including driver API
documentation and a new governor, cpufreq updates including a new
driver for Armada 8K, thermal cleanups and more, some energy-aware
scheduling (EAS) enabling changes, new chips support in the intel_idle
and RAPL drivers and assorted cleanups in some other places.
Specifics:
- Update the PM-runtime framework to use ktime instead of jiffies for
accounting (Thara Gopinath, Vincent Guittot)
- Optimize the autosuspend code in the PM-runtime framework somewhat
(Ladislav Michl)
- Add a PM core flag to mark devices that don't need any form of
power management (Sudeep Holla)
- Introduce driver API documentation for cpuidle and add a new
cpuidle governor for tickless systems (Rafael Wysocki)
- Add Jacobsville support to the intel_idle driver (Zhang Rui)
- Clean up a cpuidle core header file and the cpuidle-dt and ACPI
processor-idle drivers (Yangtao Li, Joseph Lo, Yazen Ghannam)
- Add new cpufreq driver for Armada 8K (Gregory Clement)
- Fix and clean up cpufreq core (Rafael Wysocki, Viresh Kumar, Amit
Kucheria)
- Add support for light-weight tear-down and bring-up of CPUs to the
cpufreq core and use it in the cpufreq-dt driver (Viresh Kumar)
- Fix cpu_cooling Kconfig dependencies, add support for CPU cooling
auto-registration to the cpufreq core and use it in multiple
cpufreq drivers (Amit Kucheria)
- Fix some minor issues and do some cleanups in the davinci,
e_powersaver, ap806, s5pv210, qcom and kryo cpufreq drivers
(Bartosz Golaszewski, Gustavo Silva, Julia Lawall, Paweł Chmiel,
Taniya Das, Viresh Kumar)
- Add a Hisilicon CPPC quirk to the cppc_cpufreq driver (Xiongfeng
Wang)
- Clean up the intel_pstate and acpi-cpufreq drivers (Erwan Velu,
Rafael Wysocki)
- Clean up multiple cpufreq drivers (Yangtao Li)
- Update cpufreq-related MAINTAINERS entries (Baruch Siach, Lukas
Bulwahn)
- Add support for exposing the Energy Model via debugfs and make
multiple cpufreq drivers register an Energy Model to support
energy-aware scheduling (Quentin Perret, Dietmar Eggemann, Matthias
Kaehlcke)
- Add Ice Lake mobile and Jacobsville support to the Intel RAPL
power-capping driver (Gayatri Kammela, Zhang Rui)
- Add a power estimation helper to the operating performance points
(OPP) framework and clean up a core function in it (Quentin Perret,
Viresh Kumar)
- Make minor improvements in the generic power domains (genpd), OPP
and system suspend frameworks and in the PM core (Aditya Pakki,
Douglas Anderson, Greg Kroah-Hartman, Rafael Wysocki, Yangtao Li)"
* tag 'pm-5.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (80 commits)
cpufreq: kryo: Release OPP tables on module removal
cpufreq: ap806: add missing of_node_put after of_device_is_available
cpufreq: acpi-cpufreq: Report if CPU doesn't support boost technologies
cpufreq: Pass updated policy to driver ->setpolicy() callback
cpufreq: Fix two debug messages in cpufreq_set_policy()
cpufreq: Reorder and simplify cpufreq_update_policy()
cpufreq: Add kerneldoc comments for two core functions
PM / core: Add support to skip power management in device/driver model
cpufreq: intel_pstate: Rework iowait boosting to be less aggressive
cpufreq: intel_pstate: Eliminate intel_pstate_get_base_pstate()
cpufreq: intel_pstate: Avoid redundant initialization of local vars
powercap/intel_rapl: add Ice Lake mobile
ACPI / processor: Set P_LVL{2,3} idle state descriptions
cpufreq / cppc: Work around for Hisilicon CPPC cpufreq
ACPI / CPPC: Add a helper to get desired performance
cpufreq: davinci: move configuration to include/linux/platform_data
cpufreq: speedstep: convert BUG() to BUG_ON()
cpufreq: powernv: fix missing check of return value in init_powernv_pstates()
cpufreq: longhaul: remove unneeded semicolon
cpufreq: pcc-cpufreq: remove unneeded semicolon
..
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into arm/late
DaVinci SoC updates for v5.1 (part 3)
-------------------------------------
This pull request gets rid of mach-davinci private interrupt controller
implmentations (aintc and cp_initc) and moves them to drivers/irqchip.
mach/irqs.h usage outside of mach-davinci has been rid of.
The driver changes (input and irqchip) have been acked by respective
maintainers.
* tag 'davinci-for-v5.1/soc-part3' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci: (57 commits)
ARM: davinci: remove intc related fields from davinci_soc_info
irqchip: davinci-cp-intc: move the driver to drivers/irqchip
ARM: davinci: cp-intc: remove redundant comments
ARM: davinci: cp-intc: drop GPL license boilerplate
ARM: davinci: cp-intc: use readl/writel_relaxed()
ARM: davinci: cp-intc: unify error handling
ARM: davinci: cp-intc: improve coding style
ARM: davinci: cp-intc: request the memory region before remapping it
ARM: davinci: cp-intc: use the new-style config structure
ARM: davinci: cp-intc: convert all hex numbers to lowercase
ARM: davinci: cp-intc: use a common prefix for all symbols
ARM: davinci: cp-intc: add the new config structures for da8xx SoCs
irqchip: davinci-cp-intc: add a new config structure
ARM: davinci: cp-intc: add a wrapper around cp_intc_init()
ARM: davinci: cp-intc: remove cp_intc.h
irqchip: davinci-aintc: move the driver to drivers/irqchip
ARM: davinci: aintc: remove unnecessary includes
ARM: davinci: aintc: remove the timer-specific irq_set_handler()
ARM: davinci: aintc: request memory region before remapping it
ARM: davinci: aintc: unify error handling
...
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The fields related to the two davinci interrupt controllers are no
longer used. Remove them.
Reviewed-by: David Lechner <david@lechnology.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
The cp-intc driver has now been cleaned up. Move it to drivers/irqchip
where it belongs.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: David Lechner <david@lechnology.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
We don't need comments explaining what functions with obvious names do.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: David Lechner <david@lechnology.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
Replace the GPLv2 license boilerplate with an SPDX identifier and add
myself as a second author.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
Replace all calls to __raw_readl() & __raw_writel() with readl_relaxed()
and writel_relaxed() respectively. It's safe to do as there's no
endianness conversion being done in the code.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
Instead of dumping stack traces, just print a specific error message
in aintc driver.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
Drop tabs from variable initialization. Arrange variables in reverse
christmas-tree order. Add a newline before a return.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
Add a missing call to request_mem_region() before calling ioremap() to
make sure it's not been requested by another user.
Reviewed-by: David Lechner <david@lechnology.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
Modify the cp-intc driver to take all its configuration from the new
config structure. Stop referencing davinci_soc_info in any way.
Move the declaration for davinci_cp_intc_init() to
irq-davinci-cp-intc.h and make it take the new config structure as
parameter. Convert all users to the new version.
Also: since the two da8xx SoCs default all irq priorities to 7, just
drop the priority configuration at all and hardcode the channels to 7.
It will simplify the driver code and make our lives easier when it
comes to device-tree support.
Reviewed-by: David Lechner <david@lechnology.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
Use lowercase letters in hexadecimal numbers in the cp-intc driver as
is done in most of the kernel code base.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: David Lechner <david@lechnology.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
In preparation for moving the driver to drivers/irqchip do some
cleanup: use a common prefix for all symbols.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: David Lechner <david@lechnology.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
Add the new-style config structures for da8xx SoCs. They will be used
once we make the cp-intc driver stop using davinci_soc_info.
Reviewed-by: David Lechner <david@lechnology.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
We're going to extend the cp_intc_init() function with a config
structure so we can drop the intc-related fields from davinci_soc_info.
Once we do it, we won't be able to use this routine directly as the
init_irq callback. Wrap the calls in additional helpers that don't
take parameters and can be assigned to init_irq.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: David Lechner <david@lechnology.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
