summaryrefslogtreecommitdiff
path: root/arch/arm/boot
AgeCommit message (Collapse)AuthorFilesLines
2022-10-26ARM: dts: axp803/axp81x: Drop GPIO LDO pinctrl nodesSamuel Holland1-14/+0
The "ldo-io0" and "ldo-io1" regulators are enabled/disabled by toggling the pinmux between two functions. This happens in the regulator driver. Setting the pinmux to "ldo" in the DT is inappropriate because it would enable the regulator before the driver has a chance to set the correct initial voltage. Signed-off-by: Samuel Holland <samuel@sholland.org> Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com> Link: https://lore.kernel.org/r/20220916042751.47906-2-samuel@sholland.org Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
2022-10-26ARM: dts: sunxi: correct indentationKrzysztof Kozlowski1-7/+7
Do not use spaces for indentation. Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com> Link: https://lore.kernel.org/r/20221002091959.68815-1-krzysztof.kozlowski@linaro.org Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
2022-10-26ARM: dts: omap: correct indentationKrzysztof Kozlowski9-101/+101
Do not use spaces for indentation. Link: https://lore.kernel.org/r/20221002092002.68880-1-krzysztof.kozlowski@linaro.org Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
2022-10-26ARM: dts: kirkwood: correct indentationKrzysztof Kozlowski29-113/+113
Do not use spaces for indentation. Link: https://lore.kernel.org/r/20221002092007.68955-1-krzysztof.kozlowski@linaro.org Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
2022-10-26ARM: dts: armada: correct indentationKrzysztof Kozlowski5-26/+26
Do not use spaces for indentation. Link: https://lore.kernel.org/r/20221002092008.69003-1-krzysztof.kozlowski@linaro.org Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
2022-10-26ARM: dts: ti: correct indentationKrzysztof Kozlowski4-20/+20
Do not use spaces for indentation. Link: https://lore.kernel.org/r/20221002092010.69030-1-krzysztof.kozlowski@linaro.org Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
2022-10-24ARM: dts: socfpga: arria10: Increase NAND boot partition sizeTeoh Ji Sheng1-2/+2
Content in NAND boot partition have exceeded 32MB defined in device tree node. Increase boot partition size to 37MB to support larger kernel Image and FPGA bitstream. Signed-off-by: Teoh Ji Sheng <ji.sheng.teoh@intel.com> Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
2022-10-24ARM: dts: lan966x: Add interrupt support for PHYs on pcb8290Horatiu Vultur1-0/+16
Add interrupt support for the PHYs found on pcb8290. They are all sharing the same interrupt line towards lan966x. Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com> Link: https://lore.kernel.org/r/20220915064112.1935051-1-horatiu.vultur@microchip.com
2022-10-24ARM: dts: at91: sama7g5: fix signal name of pin PB2Mihai Sain1-1/+1
The signal name of pin PB2 with function F is FLEXCOM11_IO1 as it is defined in the datasheet. Fixes: 7540629e2fc7 ("ARM: dts: at91: add sama7g5 SoC DT and sama7g5-ek") Signed-off-by: Mihai Sain <mihai.sain@microchip.com> Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com> Link: https://lore.kernel.org/r/20221017083119.1643-1-mihai.sain@microchip.com
2022-10-24ARM: dts: imx6qdl-sabre*: fix Egalax touchscreen propertiesDmitry Torokhov2-6/+6
This patch fixes interrupt trigger (should be level low as that is what the driver is always using), the GPIO that is the interrupt source that is also used to wake up chip by driving the line low. The proper polarity is be needed for converting the driver to gpiod API. Acked-by: Shawn Guo <shawnguo@kernel.org> Link: https://lore.kernel.org/r/20220920042608.1865560-1-dmitry.torokhov@gmail.com Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2022-10-24ARM: dts: stm32: enable USB OTG in dual role mode on stm32mp135f-dkFabrice Gasnier1-0/+34
The USB OTG controller provides the USB data available on stm32mp135f-dk, on the Type-C connector. Data role is determined by "usb-role-switch". A STM32G0 provides the USB Type-C and Power Delivery connectivity. It controls dual role power and dual role data through UCSI protocol over I2C. It's wired on I2C1, with an interrupt pin on PI2 GPIO. Its firmware maybe updated over I2C, so use the optional firmware-name to enable firmware update. Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com> Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com> Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
2022-10-24ARM: dts: stm32: add pins for stm32g0 typec controller on stm32mp13Fabrice Gasnier1-0/+7
Add gpio pin configuration to be used with stm32g0 typec controller. Define the PI2 to enable internal pull-up on stm32mp13, used as interrupt pin on stm32mp135f-dk board. Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com> Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
2022-10-24ARM: dts: stm32: enable USB Host EHCI on stm32mp135f-dkAmelie Delaunay1-0/+13
USBH Host EHCI controller manages the USB High-Speed hub controller IC offering Type-A CN5 & CN6 connectors available on stm32mp135f-dk. USB Host OHCI controller doesn't need to be enabled as Full-Speed and Low-Speed traffic will be managed by the hub. This USB2514B onboard hub is supplied by a 3v3 PMIC regulator. Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com> Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com> Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
2022-10-24ARM: dts: stm32: enable USB HS phys on stm32mp135f-dkAmelie Delaunay1-0/+32
USBPHYC manages the two USB High-Speed phys. port0 is used by USBH and port1 is used by USBOTG. Enable and tune both PHYs on stm32mp135f-dk. Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com> Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com> Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
2022-10-24ARM: dts: stm32: add fixed regulators to support usb on stm32mp135f-dkFabrice Gasnier1-0/+16
Add VDD_USB and 3V3_SW regulators on stm32mp135f-dk. Temporary add them as fixed regulators, waiting for full SCMI regulators support. This is a precursor patch to enable USB support on STM32MP13: - VDD_USB supplies the STM32MP13 USB internals - 3V3_SW supplies various peripherals, including the onboard HUB. Note: USB support requires these regulators to be enabled before entering the kernel. Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com> Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
2022-10-24ARM: dts: stm32: add USB OTG HS support on stm32mp131Amelie Delaunay1-0/+17
This patch adds USB OTG HS support on stm32mp131. Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com> Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com> Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
2022-10-24ARM: dts: stm32: add UBSH EHCI and OHCI support on stm32mp131Amelie Delaunay1-0/+19
This patch adds USB Host EHCI and OHCI support on stm32mp131. Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com> Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com> Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
2022-10-24ARM: dts: stm32: add USBPHYC and dual USB HS PHY support on stm32mp131Amelie Delaunay1-0/+23
This patch adds support for USBPHYC and its two USB HS PHY on stm32mp131. Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com> Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com> Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
2022-10-24ARM: dts: stm32: add PWR fixed regulators on stm32mp131Fabrice Gasnier1-0/+22
Add 1v1, 1v8 and 3v3 PWR regulators on stm32mp131. Temporary add them as fixed regulators, waiting for full SCMI regulators support. This is a precursor patch to enable USB support on STM32MP13. Note: USB support requires these regulators to be enabled before entering kernel. Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com> Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
2022-10-24ARM: dts: stm32: Fix AV96 WLAN regulator gpio propertyMarek Vasut1-1/+1
The WLAN regulator uses 'gpios' property instead of 'gpio' to specify regulator enable GPIO. While the former is also currently handled by the Linux kernel regulator-fixed driver, the later is the correct one per DT bindings. Update the DT to use the later. Fixes: 7dd5cbba42c93 ("ARM: dts: stm32: Enable WiFi on AV96") Signed-off-by: Marek Vasut <marex@denx.de> Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
2022-10-24ARM: dts: stm32: add adc support on stm32mp135f-dkOlivier Moysan1-0/+25
Configure ADC support on stm32mp135f-dk. ADC can be used for USB Type-C CC1 & CC2 pins wired to in6 & in12. Signed-off-by: Olivier Moysan <olivier.moysan@foss.st.com> Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
2022-10-24ARM: dts: stm32: add dummy vdd_adc regulator on stm32mp135f-dkOlivier Moysan1-0/+8
Add a dummy fixed regulator vdd-adc for STM32 ADC, on STM32MP135F-DK board, while SCMI regulators are not available. This patch will have to be removed when SCMI regulator support is added to STM32MP13. This patch intends to allow ADC enabling on STM32MP13. With this patch the ADC can probe but it cannot return valid conversion data, as it's regulator is not actually enabled. Signed-off-by: Olivier Moysan <olivier.moysan@foss.st.com> Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
2022-10-24ARM: dts: stm32: add adc pins muxing on stm32mp135f-dkOlivier Moysan1-0/+7
Define pins muxing that can be used for ADC on stm32mp135f-dk board (USB Type-C CC1 & CC2 pins). Signed-off-by: Olivier Moysan <olivier.moysan@foss.st.com> Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
2022-10-24ARM: dts: stm32: add adc support to stm32mp13Olivier Moysan2-0/+74
Add ADC1 and ADC2 support to STM32MP13 SoC family. The STM32MP131 provides only ADC2, while other STM32MP13 SoCs provide both ADC1 and ADC2. Internal channels support limitations: - VREFINT internal channel requires calibration data from OTP memory. The nvmem properties used to access OTP are not defined for time being, as OTP support is not yet enabled. - VBAT internal channel is not defined by default in SoC DT, and has be defined in board DT when needed, instead. This avoids unwanted current consumption on battery, when ADC conversions are performed on any other channels. Signed-off-by: Olivier Moysan <olivier.moysan@foss.st.com> Reviewed-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com> Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
2022-10-24ARM: dts: stm32: Drop MMCI interrupt-namesMarek Vasut3-7/+0
The pl18x MMCI driver does not use the interrupt-names property, the binding document has been updated to recommend this property be unused, remove it. Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Reviewed-by: Yann Gautier <yann.gautier@foss.st.com> Signed-off-by: Marek Vasut <marex@denx.de> Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
2022-10-24ARM: dts: stm32: update vbus-supply of usbphyc_port0 on stm32mp157c-ev1Amelie Delaunay1-0/+5
phy-stm32-usbphyc bindings uses a connector node with vbus-supply property. Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com> Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com> Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
2022-10-24ARM: dts: stm32: add support for USB2514B onboard hub on stm32mp157c-ev1Fabrice Gasnier1-0/+8
Add support for USB2514B onboard hub on stm32mp157c EV1 board. The HUB is supplied by a 3v3 PMIC regulator. Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com> Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
2022-10-24ARM: dts: ls1021: correct indentationKrzysztof Kozlowski1-5/+5
Do not use spaces for indentation. Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2022-10-24ARM: dts: vf610-zii-dev-rev-c: fix polarity of at86rf233 reset lineDmitry Torokhov1-1/+1
at86rf230 driver starts with having reset line high, and then drives it low and then high again, and even calls it "rstn" internally, therefore it needs to be annotated as "active low" in the DTS. This will make difference when at86rf230 driver will be converted to gpiod API that respects declared line polarity. Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2022-10-24ARM: dts: imx7-colibri: remove spurious debounce propertyMarcel Ziswiler1-1/+0
Remove spurious debounce property from linux,extcon-usb-gpio. Note that debouncing is hard-coded to 20 ms (USB_GPIO_DEBOUNCE_MS define). Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2022-10-24ARM: dts: colibri-imx6: specify usbh_pen gpio being active-lowMarcel Ziswiler1-1/+1
Specify USBH_PEN GPIO being active-low rather than active-high. Note that this should not have any functional impact as for fixed regulators the regular GPIO polarity is ignored and a true active-high enable GPIO would need an additional enable-active-high property which is/was not the case here. However, this may be rather confusing which this patch fixes. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2022-10-24ARM: dts: colibri-imx6: move vbus-supply to module level device treeMarcel Ziswiler4-5/+7
Move USB VBUS supply from single carrier board to module level device tree. This pin is as per Colibri module family standard. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2022-10-24ARM: dts: colibri-imx6: usb dual-role switchingPhilippe Schenker1-2/+11
Introduce USBC_DET GPIO based USB dual-role aka device/host switching. While at it re-work pinmux comment adding SODIMM number to the USBC_DET entry. Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com> Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2022-10-24ARM: dts: imx: Add devicetree for Kobo Aura 2Andreas Kemnade2-0/+556
This adds a devicetree for the Kobo Aura 2 Ebook reader. It is based on boards marked with "37NB-E60QL0+4B1". It is equipped with an i.MX6SL SoC. Expected to work: - Buttons - Wifi (with external module) - LED - uSD - USB - RTC - Fuel Gauge - Backlight (if the required regulator is probed before the backlight, specifying a supply is not supported by backlightdriver) Signed-off-by: Andreas Kemnade <andreas@kemnade.info> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2022-10-21ARM: dts: stm32: Add DHCOR based Testbench boardMarek Vasut3-0/+189
Add DT for DHCOR Testbench board, which is a testbench for testing of DHCOR SoM during manufacturing. This is effectively a trimmed down version of AV96 board with CSI-2 bridge, HDMI bridge, WiFi, Audio and LEDs removed and used as GPIOs instead. Furthermore, the PMIC Buck3 is always configured from PMIC NVM to cater for both 1V8 and 3V3 SoM variant. Signed-off-by: Marek Vasut <marex@denx.de> Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
2022-10-21ARM: dts: stm32: Replace SAI format with dai-format DT propertyMarek Vasut3-5/+5
The dai-format and format are handled equally by sound-core.c , the later is however the only documented property in audio-graph-port.yaml . Switch to the later. Signed-off-by: Marek Vasut <marex@denx.de> Reviewed-by: Olivier Moysan <olivier.moysan@foss.st.com> Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
2022-10-21ARM: dts: stm32: Drop linux,default-trigger = "none" from AV96Marek Vasut1-1/+0
The default-trigger setting set to none has no impact and triggers DT dtbs_check warning, remove it: " arch/arm/boot/dts/stm32mp157a-dhcor-avenger96.dtb: led: led4:linux,default-trigger: 'oneOf' conditional failed, one must be fixed: " Signed-off-by: Marek Vasut <marex@denx.de> Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
2022-10-21ARM: dts: stm32: Rename mdio0 to mdioMarek Vasut8-8/+8
Replace "mdio0" node with "mdio" to match mdio.yaml DT schema. Signed-off-by: Marek Vasut <marex@denx.de> Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
2022-10-21ARM: dts: stm32: Drop stm32mp15xc.dtsi from Avenger96Marek Vasut1-1/+0
The Avenger96 is populated with STM32MP157A DHCOR SoM, drop the stm32mp15xc.dtsi which should only be included in DTs of devices which are populated with STM32MP15xC/F SoC as the stm32mp15xc.dtsi enables CRYP block not present in the STM32MP15xA/D SoC . Fixes: 7e76f82acd9e1 ("ARM: dts: stm32: Split Avenger96 into DHCOR SoM and Avenger96 board") Signed-off-by: Marek Vasut <marex@denx.de> Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com> Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
2022-10-20ARM: dts: stm32: add sdmmc cd-gpios for STM32MP135F-DKYann Gautier1-1/+1
On STM32MP135F-DK, the SD card detect GPIO is GPIOH4. Signed-off-by: Yann Gautier <yann.gautier@foss.st.com> Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
2022-10-19ARM: dts: armada-375: Update network description to match schemaMarcin Wojtas1-4/+8
Update the PP2 ethernet ports subnodes' names to match schema enforced by the marvell,pp2.yaml contents. Add new required properties ('reg') which contains information about the port ID, keeping 'port-id' ones for backward compatibility. Signed-off-by: Marcin Wojtas <mw@semihalf.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2022-10-18ARM: dts: aspeed: align SPI node name with dtschemaKrzysztof Kozlowski5-5/+5
The node names should be generic and DT schema expects certain pattern. Link: https://lore.kernel.org/r/20220830180344.15657-1-krzysztof.kozlowski@linaro.org Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
2022-10-18ARM: dts: stm32: add fake interrupt propoerty for ASync notif - TEMP/TO REMOVEAlexandre Torgue1-0/+2
Current internal optee version enables ASYNc notif and in suche case interrupt is mandatory in optee node. Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
2022-10-18ARM: dts: qcom: apq8064: fix coresight compatibleLuca Weiss1-1/+1
There's a typo missing the arm, prefix of arm,coresight-etb10. Fix it to make devicetree validation happier. Signed-off-by: Luca Weiss <luca@z3ntu.xyz> Fixes: 7a5c275fd821 ("ARM: dts: qcom: Add apq8064 CoreSight components") Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org> Signed-off-by: Bjorn Andersson <andersson@kernel.org> Link: https://lore.kernel.org/r/20221013190657.48499-3-luca@z3ntu.xyz
2022-10-18ARM: dts: qcom: apq8084: fix compatible for l2-cacheLuca Weiss1-1/+1
The compatible "qcom,arch-cache" for l2-cache does not exist, and all other Qualcomm boards use just "cache" for it. Fix it. Signed-off-by: Luca Weiss <luca@z3ntu.xyz> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org> Signed-off-by: Bjorn Andersson <andersson@kernel.org> Link: https://lore.kernel.org/r/20221013190657.48499-2-luca@z3ntu.xyz
2022-10-18ARM: dts: qcom: ipq8064-rb3011: fix nand node validationLuca Weiss1-2/+1
The devicetree documentation for the nand node requires the subnode be called nand@ and no compatible is needed. Signed-off-by: Luca Weiss <luca@z3ntu.xyz> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org> Signed-off-by: Bjorn Andersson <andersson@kernel.org> Link: https://lore.kernel.org/r/20221013190657.48499-1-luca@z3ntu.xyz
2022-10-18ARM: dts: qcom: correct indentationKrzysztof Kozlowski1-1/+1
Do not use spaces for indentation. Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org> Signed-off-by: Bjorn Andersson <andersson@kernel.org> Link: https://lore.kernel.org/r/20221002092000.68844-1-krzysztof.kozlowski@linaro.org
2022-10-18ARM: dts: qcom: Add support for Samsung Galaxy Tab 4 10.1 (SM-T530)Matti Lehtimäki2-0/+454
Add a device tree for the Samsung Galaxy Tab 4 10.1 (SM-T530) wifi tablet based on the apq8026 platform. Currently supported are accelerometer sensor, hall sensor, internal storage, physical buttons (power & volume), screen (based on simple-framebuffer set up by the bootloader), sdcard, touchscreen and USB. Signed-off-by: Matti Lehtimäki <matti.lehtimaki@gmail.com> Signed-off-by: Bjorn Andersson <andersson@kernel.org> Link: https://lore.kernel.org/r/20220927214940.244480-4-matti.lehtimaki@gmail.com
2022-10-18ARM: dts: qcom: pm8226: Add node for the GPIOsMatti Lehtimäki1-0/+10
The PM8226 provides 8 GPIOs. Add a node to support them. Signed-off-by: Matti Lehtimäki <matti.lehtimaki@gmail.com> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org> Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by: Bjorn Andersson <andersson@kernel.org> Link: https://lore.kernel.org/r/20220927214940.244480-2-matti.lehtimaki@gmail.com
2022-10-18ARM: dts: qcom: pmx65: use node name "gpio" for spmi-gpioLuca Weiss1-1/+1
All other usages of qcom,spmi-gpio use the gpio@ node name, and this is also validated by the dt binding check. Fix it. Signed-off-by: Luca Weiss <luca@z3ntu.xyz> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org> Signed-off-by: Bjorn Andersson <andersson@kernel.org> Link: https://lore.kernel.org/r/20220925190622.111505-1-luca@z3ntu.xyz
generated by cgit v1.2.3 (git 2.39.0) at 2025-09-26 19:59:49 +0300