| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The binding of R_INTC was updated to allow specifying interrupts other
than the external NMI, since routing those interrupts through the R_INTC
driver allows using them for wakeup.
Update the device trees to use the new binding.
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
|
|
The R_INTC block controls more than just the NMI, and it is a different
hardware block than the NMI INTC found in some other Allwinner SoCs, so
the label "nmi_intc" is inaccurate. Name it "r_intc" to match the
compatible and to match the few references in the vendor documentation.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210118055040.21910-6-samuel@sholland.org
|
|
According to the LED bindings, the LED node names are supposed to be led
plus an optional suffix. Let's fix our users to use that new scheme.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Jernej Skrabec <jernej.skrabec@siol.net>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20210114113538.1233933-6-maxime@cerno.tech
|
|
This patch adds the Bluetooth node, and the underlying UART node if it's
missing, to the board device tree file for several boards. The LPO clock
is also added to the WiFi side's power sequencing node if it's missing,
to correctly represent the shared connections. There is also a PCM
connection for Bluetooth, but this is not covered in this patch.
These boards all have a WiFi+BT module from AMPAK, which contains one or
two Broadcom chips, depending on the model. The older AP6210 contains
two, while the newer AP6212 and AP6330 contain just one, as they use
two-in-one combo chips.
The Bluetooth side of the module is always connected to a UART on the
same pingroup as the SDIO pins for the WiFi side, in a 4 wire
configuration. Power to the VBAT and VDDIO pins are provided either by
the PMIC, using one or several of its regulator outputs, or other fixed
regulators on the board. The VBAT and VDDIO pins are shared with the
WiFi side, which would correspond to vmmc-supply and vqmmc-supply in the
mmc host node. A clock output from the SoC or the external X-Powers RTC
provides the LPO low power clock at 32.768 kHz.
All the boards covered in this patch are ones that do not require extra
changes to the SoC's dtsi file. For the remaining boards that I have
worked on, properties or device nodes for the LPO clock's source are
missing.
For the Cubietruck, the LPO clock is fed from CLK_OUT_A, which needs to
be muxed on pin PI12. This can be represented in multiple ways. This
patch puts the pinctrl property in the pin controller node. This is due
to limitations in Linux, where pinmux settings, even the same one, can
not be shared by multiple devices. Thus we cannot put it in both the
WiFi and Bluetooth device nodes. Putting it the CCU node is another
option, but Linux's CCU driver does not handle pinctrl. Also the pin
controller is guaranteed to be initialized after the CCU, when clocks
are available. And any other devices that use muxed pins are guaranteed
to be initialized after the pin controller. Thus having the CLK_OUT_A
pinmux reference be in the pin controller node is a good choice without
having to deal with implementation issues.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
|
|
The i2c nodes were pre-populated to ease the use of overlays. However, now
that we provide default muxing options for those nodes, the one in the DTS
don't provide any content at all.
Remove them.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
The I2C's and MMC0 controllers have only one muxing option in the SoC. In
such a case, we can just move the muxing into the DTSI, and remove it from
the DTS.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
All our pinctrl nodes were using a node name convention with a unit-address
to differentiate the different muxing options. However, since those nodes
didn't have a reg property, they were generating warnings in DTC.
In order to accomodate for this, convert the old nodes to the syntax we've
been using for the new SoCs, including removing the letter suffix of the
node labels to the bank of those pins to make things more readable.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
DTC will emit a warning on our OPPs nodes for the common DTSI between the
A23 and A33 since those nodes use the frequency as unit addresses, but
don't have a matching reg property.
Fix this by moving the frequency to the node name instead.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
Using the cd-inverted property is not useful when GPIOs are used as card
detects since the polarity can be specified with the usual
GPIO_ACTIVE_(HIGH|LOW) GPIO flags. It has also caused confusion for
U-Boot developers, so migrate all sunxi boards away from cd-inverted.
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
The Bananapi M2-Magic is a board with an A33, a USB host and USB OTG
connectors, and 8GB eMMC, an AP6212 WiFi/Bluetooth chip and connectors for
DSI, CSI and GPIOs.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
[wens@csie.org: Correct subject prefix case]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
|
