| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The correct DT property for specifying a GPIO used for reset
is "reset-gpios", fix this here.
Fixes: 4341881d0562 ("ARM: dts: Add devicetree for Gumstix Pepper board")
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The at24 driver allows to register I2C EEPROM chips using different vendor
and devices, but the I2C subsystem does not take the vendor into account
when matching using the I2C table since it only has device entries.
But when matching using an OF table, both the vendor and device has to be
taken into account so the driver defines only a set of compatible strings
using the "atmel" vendor as a generic fallback for compatible I2C devices.
So add this generic fallback to the device node compatible string to make
the device to match the driver using the OF device ID table.
Signed-off-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This patch fixes the following DTC warnings:
"Node /memory has a reg or ranges property, but no unit name"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This patch fixes the following DTC warnings for many boards:
"Node /leds/led@1 has a unit name, but no reg property"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This patch fixes the following DTC warnings for many boards:
"Node /gpio_keys/button0@10 has a unit name, but no reg property"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This patch fixes the following DTC warnings for many boards:
"Node /fixedregulator@0 has a unit name, but no reg property"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This reverts commit 8e6ebfaa9b384088002baa10f7534efa73a0794e.
Without the patch reverted regulators will not work. This prevents
MMC to be working for example so the boards can not boot to
MMC rootfs.
Tested it on beaglebone white and bisect also points to the
reverted commit.
The issue can be also fixed by adding "regulator-compatible =" to all board
dts file for the regulators.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Though the keyboard driver for GPIO buttons(gpio-keys) will continue to
check for/support the legacy "gpio-key,wakeup" boolean property to
enable gpio buttons as wakeup source, "wakeup-source" is the new
standard binding.
This patch replaces the legacy "gpio-key,wakeup" with the unified
"wakeup-source" property in order to avoid any futher copy-paste
duplication.
Cc: "Benoît Cousson" <bcousson@baylibre.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: linux-omap@vger.kernel.org
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Switch to use the ti,edma3-tpcc and ti,edma3-tptc binding for the eDMA3 and
enable the DMA even crossbar with ti,am335x-edma-crossbar.
With the new bindings boards can customize and tweak the DMA channel
priority to match their needs. With the new binding the memcpy is safe
to be used since with the old binding it was not possible for a driver
to know which channel is allowed to be used as non HW triggered channel.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
remove tps65217.dtsi and adapt all boards, which
used it.
Signed-off-by: Heiko Schocher <hs@denx.de>
Tested-by: Keerthy <j-keerthy@ti.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Use the pinmux IOPAD macro to define the register absolute physical
address instead of the offset from the padconf base address. This
makes the DTS easier to read since matches the addresses listed in
the Technical Reference Manual.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Audio-in was incorrectly routed to Line In. It should be Mic3L as per
schematic.
Using mic-bias voltage at 2.0v (<0x1>) does not work for some reason. There
is no voltage seen on micbias (R127). Mic-bias voltage of 2.5v (<0x2>) works.
I see voltage of 2.475v across GND and micbias.
With these changes, I can record audio with a pair of proliferate TRRS earbuds.
Signed-off-by: Adam YH Lee <adam.yh.lee@gmail.com>
Acked-by: Ash Charles <ashcharles@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The device tree for Gumstix Pepper has DCDC2 and
DCDC3 correctly labelled but the upper limit values
are wrong. The confusion is due to the hardware
quirk where the DCDC2 and DCDC3 wires are flipped
in Pepper.
Signed-off-by: Arun Bharadwaj <arun@gumstix.com>
Tested-by: Ash Charles <ashcharles@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Boot process is halting in midway because some of the necessary voltage
regulators are deemed unused and subsequently powered off, leading to
a completely unresponsive system.
Most of the device nodes had correct voltage regulator attachments.
Yet these nodes had to set stricter enforcement on them through
'regulator-boot-on' and 'regulator-always-on' to function correctly.
The consumers of the regulators this commit affect are the followings:
DCDC1: vdd_1v8 system supply, USB-PHY, and ADC
DCDC2: Core domain
DCDC3: MPU core domain
LDO1: RTC
LDO2: 3v3 IO domain
LDO3: USB-PHY; not a boot-time requirement
LDO4: LCD [16:23]
All but LDO3 need to be always-on for the system to be functional.
Additionally regulator-name properties have been added for the kernel to
display the name from the schematic. This will improve diagnostics.
Signed-off-by: Adam YH Lee <adam.yh.lee@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This adds the Gumstix Pepper[1] single-board computer based on the
TI AM335x processor. Schematics are available [2].
[1] https://store.gumstix.com/index.php/products/344/
[2] https://pubs.gumstix.com/boards/PEPPER/
Signed-off-by: Ash Charles <ashcharles@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
