| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
apq8016-sbc is one of the compaitibles for this board, but is not
documented, so drop it. This fixes these two warns:
arch/arm64/boot/dts/qcom/apq8016-sbc.dt.yaml: /: compatible: ['qcom,apq8016-sbc', 'qcom,apq8016', 'qcom,sbc']
is not valid under any of the given schemas (Possible causes of the failure):
arch/arm64/boot/dts/qcom/apq8016-sbc.dt.yaml: /: compatible: ['qcom,apq8016-sbc', 'qcom,apq8016', 'qcom,sbc'] is too long
arch/arm64/boot/dts/qcom/apq8016-sbc.dt.yaml: /: compatible:0: 'qcom,apq8016-sbc'
is not one of ['qcom,apq8064-cm-qs600', 'qcom,apq8064-ifc6410']
arch/arm64/boot/dts/qcom/apq8016-sbc.dt.yaml: /: compatible:0: 'qcom,apq8016-sbc'
is not one of ['qcom,apq8074-dragonboard']
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20210308060826.3074234-2-vkoul@kernel.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
At boot time the following happens:
1. Device core gets ready to probe our SPI driver.
2. Device core applies SPI controller's "default" pinctrl.
3. Device core calls the SPI driver's probe() function which will
eventually setup the chip select GPIO as "unasserted".
Thinking about the above, we can find:
a) For SPI devices that the BIOS inits (Cr50 and EC), the BIOS would
have had them configured as "GENI" pins and not as "GPIO" pins.
b) It turns out that our BIOS also happens to init these pins as
"output" (even though it doesn't need to since they're not muxed as
GPIO) but leaves them at the default state of "low".
c) As soon as we apply the "default" chip select it'll switch the
function to GPIO and stop driving the chip select high (which is
how "GENI" was driving it) and start driving it low.
d) As of commit 9378f46040be ("UPSTREAM: spi: spi-geni-qcom: Use the
new method of gpio CS control"), when the SPI core inits things it
inits the GPIO to be "deasserted". Prior to that commit the GPIO
was left untouched until first use.
e) When the first transaction happens we'll assert the chip select and
then deassert it after done.
So before the commit to change us to use gpio descriptors we used to
have a _really long_ assertion of chip select before our first
transaction (because it got pulled down and then the first "assert"
was a no-op). That wasn't great but (apparently) didn't cause any
real harm.
After the commit to change us to use gpio descriptors we end up
glitching the chip select line during probe. It would go low and then
high with no data transferred. The other side ought to be robust
against this, but it certainly could cause some confusion. It's known
to at least cause an error message on the EC console and it's believed
that, under certain timing conditions, it could be getting the EC into
a confused state causing the EC driver to fail to probe.
Let's fix things to avoid the glitch. We'll add an extra pinctrl
entry that sets the value of the pin to output high (CS deasserted)
before doing anything else. We'll do this in its own pinctrl node
that comes before the normal pinctrl entries to ensure that the order
is correct and that this gets applied before the mux change.
This change is in the trogdor board file rather than in the SoC dtsi
file because chip select polarity can be different depending on what's
hooked up and it doesn't feel worth it to spam the SoC dtsi file with
both options. The board file would need to pick the right one anyway.
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Fixes: cfbb97fde694 ("arm64: dts: qcom: Switch sc7180-trogdor to control SPI CS via GPIO")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20210218145456.1.I1da01a075dd86e005152f993b2d5d82dd9686238@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Using pdc interrupts for USB instead of GIC interrupts to
support wake up in case xo shutdown.
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Sandeep Maheswaram <sanm@codeaurora.org>
Link: https://lore.kernel.org/r/1594235417-23066-4-git-send-email-sanm@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
This is a trogdor variant. This is mostly a grab from the downstream
tree with notable exceptions:
- I skip -rev0. This was a super early build and there's no advantage
of long term support.
- I remove sound node since sound hasn't landed upstream yet.
Cc: Gwendal Grignou <gwendal@chromium.org>
Cc: Matthias Kaehlcke <mka@chromium.org>
Cc: Stephen Boyd <swboyd@chromium.org>
Cc: Tzung-Bi Shih <tzungbi@chromium.org>
Cc: Judy Hsiao <judyhsiao@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20210301133318.v2.13.I3d1f5f8a3bf31e8014229df0d4cfdff20e9cc90f@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
This is a trogdor variant. This is mostly a grab from the downstream
tree with notable exceptions:
- I skip -rev0. This was a super early build and there's no advantage
of long term support.
- In -rev1 I translate the handling of the USB hub like is done for
similar boards. See the difference between the downstream and
upstream 'sc7180-trogdor-lazor-r0.dts' for an example. This will
need to be resolved when proper support for the USB hub is figured
out upstream.
- I remove sound node since sound hasn't landed upstream yet.
- In incorporate the pending <https://crrev.com/c/2719075> for the
keyboard.
Cc: Philip Chen <philipchen@google.com>
Cc: Matthias Kaehlcke <mka@chromium.org>
Cc: Stephen Boyd <swboyd@chromium.org>
Cc: Tzung-Bi Shih <tzungbi@chromium.org>
Cc: Judy Hsiao <judyhsiao@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20210301133318.v2.12.If93a01b30d20dccacbad4be8ddc519dc20a51a1e@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
This is a SKU variant of lazor. Add it. This squashes the downstream
patches to support this hardware.
NOTES:
- The non-touch SKU actually has "innolux,n116bca-ea1" but that driver
is still pending in simple-panel. The bindings have been Acked
though [1]. Things work well enough with the "innolux,n116bge"
timings for now, though.
- The wonky special dts just for "-rev4" arguably doesn't need to go
upstream since they weren't widely distributed, but since a few
people have them we might as well. If it ever causes problems we
can delete it.
[1] https://lore.kernel.org/r/20210115144345.v2.4.I6889e21811df6adaff5c5b8a8c80fda0669ab3a5@changeid
Cc: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20210301133318.v2.11.I556326b24441e22c8c429ce383cc157c7aaef44b@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Lazor rev3 and later use the 'lite' version of the SC7180 SoC.
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Cc: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
[dianders: Adjust commit message which referred to downstream history]
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20210301133318.v2.10.Ia3795e192f5bbe17e6714e45fcb0bf5acdbd4c17@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
For trogdor, in the latest board-2.bin file, new BDF with variant
name GO_LAZOR has been introduced, so we need this property set, for
GO_LAZOR BDF to be picked.
Cc: Philip Chen <philipchen@chromium.org>
Signed-off-by: Abhishek Kumar <kuabhs@chromium.org>
[dianders: adjusted subject line and sort order]
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20210301133318.v2.9.I4a38fe64dd79c54af80d7e4ef5940f8cf4f86e75@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Removed voting for RPMH_RF_CLK2 which is not required as it is
getting managed by BT SoC through SW_CTRL line.
Cc: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Venkata Lakshmi Narayana Gubba <gubbaven@codeaurora.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20210301133318.v2.8.I80c268f163e6d49a70af1238be442b5de400c579@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Removed the pinctrl and pin{mux,conf} for the control pins because:
1. The only need for them is for userspace control via flash_fp_mcu
2. cros-ec doesn't know what to do with them, and even if it did,
it would interfere with flash_fp_mcu at the most inopportune times
Since we're not using hogs, we rely on AP firmware to set all the
control pins correctly.
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Cc: Stephen Boyd <swboyd@chromium.org>
Cc: Craig Hesling <hesling@chromium.org>
Signed-off-by: Alexandru M Stan <amstan@chromium.org>
[dianders: adjusted since coachz isn't upstream yet]
Reviewed-by; Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20210301133318.v2.7.Ifd7b86f826b18410eada75758a7bca1eebfa336d@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
We only want to use this clk driver on CoachZ devices. Disable it for
all other Trogdor boards. NOTE: CoachZ devices aren't yet supported
upstream so until it is this is just disabled for all trogdor.
Cc: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
[dianders:adjusted since no coachz upstream yet]
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/20210301133318.v2.6.I22522b0c9db505ee43ed08e8d5d9e8fe632e7447@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Configure the pen to be a wakeup source only when the pen is ejected
instead of both when the pen is ejected and inserted. This corresponds
to wake source requirements.
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/20210301133318.v2.5.Ib9672bfbe639c96c85408d6f0217a2609eb0b70f@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Let's avoid a bit of duplication by pushing this up to the trogdor.dtsi
file.
Suggested-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20210301133318.v2.4.I1483fac4c5ae4b2d7660290ff85d69945292618f@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
The trackpad interrupt got renamed and also moved to a new GPIO on
newer boards. Let's do the move in the "trogdor.dtsi" file and then
undo it in the two old boards.
NOTE: since none of the new boards have device trees yet, this change
looks silly on its own but it will make sense after more boards are
supported.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20210301133318.v2.3.Iddf6dc8102aa4fbc3847936226fc7bf2e2cd315c@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
In general pinconf belongs in board files, not SoC files. Move it to
the only current user (trogdor). Also adjust the drive strengths and
pulls.
Cc: V Sujith Kumar Reddy <vsujithk@codeaurora.org>
Cc: Srinivasa Rao Mandadapu <srivasam@codeaurora.org>
Cc: Tzung-Bi Shih <tzungbi@chromium.org>
Cc: Judy Hsiao <judyhsiao@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20210301133318.v2.2.Id27e7e6f90c29bf623fa4880e18a14ba1dffd2d2@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Drop the old node and add the new one in its place.
Cc: Stephen Boyd <swboyd@chromium.org>
Cc: Jeykumar Sankaran <jsanka@codeaurora.org>
Cc: Chandan Uddaraju <chandanu@codeaurora.org>
Cc: Vara Reddy <varar@codeaurora.org>
Cc: Tanmay Shah <tanmay@codeaurora.org>
Cc: Rob Clark <robdclark@chromium.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
[dianders: Adjusted due to DP not itself not in upstream dts yet]
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20210301133318.v2.1.Iad06142ceb8426ce5492737bf3d9162ed0dd2b55@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Add cpufreq node and reference it for the CPUs.
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20210216111703.1838663-1-vkoul@kernel.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Now that we have GCC define, use the enums instead of numbers in the DTS
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20210212115532.1339942-8-vkoul@kernel.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
This enabled the four remoteprocs found in SM8350, audio, compute, modem
and sensor for MTP platform and adds firmware for them.
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20210212115532.1339942-7-vkoul@kernel.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Add remoteproc nodes for the audio, compute and sensor cores, define
glink for each one.
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20210212115532.1339942-6-vkoul@kernel.org
[bjorn: Replaced rpmhpd defines with constants, for now]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
SMP2P is used for interrupting and being interrupted about remoteproc
state changes related to the audio, compute, modem and sensor subsystems.
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20210212115532.1339942-5-vkoul@kernel.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Add the rmtfs as a reserved memory node.
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20210212115532.1339942-4-vkoul@kernel.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
This adds RPMH power domain found in SM8350 SoC
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20210212115532.1339942-3-vkoul@kernel.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Fix the typo s/Limaited/Limited
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20210212115532.1339942-2-vkoul@kernel.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Add the property "regulator-names" to the regulators as given in
schematics so that it is easier to understand the regulators being used
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20210204170907.63545-7-vkoul@kernel.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Enabled the UFS node found in SM8350-MTP platform, also add the
regulators associated with UFS HC and UFS phy to these nodes.
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20210204170907.63545-6-vkoul@kernel.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
This adds UFS HC and UFS phy nodes to the SM8350 DTS
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20210204170907.63545-5-vkoul@kernel.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Enable both USB controllers and associated hsphy and qmp phy nodes
on sm8350 MTP. Designate the usb_1 instance as peripheral-mode only
until proper PMIC based Type-C dual-role handling is supported.
TODO: the second USB controller is exposed to a microAB port. Dual-
role can be supported for this by adding the "usb-role-switch"
property as well as defining a USB connector node with a
"gpio-usb-b-connector" compatible. However, this requires GPIO
support from PM8350 which is still missing.
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Link: https://lore.kernel.org/r/20210116013802.1609-3-jackp@codeaurora.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20210204170907.63545-4-vkoul@kernel.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Add device nodes for the two instances each of USB3 controllers,
QMP SS PHYs and SNPS HS PHYs.
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Link: https://lore.kernel.org/r/20210116013802.1609-2-jackp@codeaurora.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20210204170907.63545-3-vkoul@kernel.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
This adds apss_smmu node to SM8350 DTS
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20210204170907.63545-2-vkoul@kernel.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
ARM architected timer interrupts DT property specifies EL2/HYP
physical interrupt and not EL2/HYP virtual interrupt for the 4th
interrupt property. As per interrupt documentation for SM8250 SoC,
the EL2/HYP physical timer interrupt is 10 and EL2/HYP virtual timer
interrupt is 12, so fix the 4th timer interrupt to be EL2 physical
timer interrupt (10 in this case).
Fixes: 60378f1a171e ("arm64: dts: qcom: sm8250: Add sm8250 dts file")
Signed-off-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Link: https://lore.kernel.org/r/744e58f725d279eb2b049a7da42b0f09189f4054.1613468366.git.saiprakash.ranjan@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
As per interrupt documentation for SM8350 SoC, the polarity
for level triggered PMU interrupt is low, fix this.
Fixes: b7e8f433a673 ("arm64: dts: qcom: Add basic devicetree support for SM8350 SoC")
Signed-off-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Link: https://lore.kernel.org/r/ca57409198477f7815e32a6a7467dcdc9b93dc4f.1613468366.git.saiprakash.ranjan@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
As per interrupt documentation for SM8250 SoC, the polarity
for level triggered PMU interrupt is low, fix this.
Fixes: 60378f1a171e ("arm64: dts: qcom: sm8250: Add sm8250 dts file")
Signed-off-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Link: https://lore.kernel.org/r/96680a1c6488955c9eef7973c28026462b2a4ec0.1613468366.git.saiprakash.ranjan@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Use the generic DT node name "power-controller" for AOSS message ram
instead of the protocol name QMP(Qualcomm Messaging Protocol) since
it is used for power management requests.
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Suggested-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Link: https://lore.kernel.org/r/15005f1441594670adcd60a300c88e41d79cad27.1614669585.git.saiprakash.ranjan@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Use the generic DT node name "power-controller" for AOSS message ram
instead of the protocol name QMP(Qualcomm Messaging Protocol) since
it is used for power management requests.
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Suggested-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Link: https://lore.kernel.org/r/044fe2e590e166060de65f074df6874ec3a79531.1614669585.git.saiprakash.ranjan@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Use the generic DT node name "power-controller" for AOSS message ram
instead of the protocol name QMP(Qualcomm Messaging Protocol) since
it is used for power management requests.
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Suggested-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Link: https://lore.kernel.org/r/55416e116dda4aad977bb050451d328b1f6b00d3.1614669585.git.saiprakash.ranjan@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Use the generic DT node name "power-controller" for AOSS message ram
instead of the protocol name QMP(Qualcomm Messaging Protocol) since
it is used for power management requests.
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Suggested-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Link: https://lore.kernel.org/r/e96d665d1e98b46a189a57e39575ae0debf37172.1614669585.git.saiprakash.ranjan@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
charger temperature
On trogdor the ADC thermal monitor is used for monitoring certain
device temperatures. All trogdor boards have at least a thermistor
for the charger temperature, optionally they may have others.
Currently the ADC thermal monitor is configured to use channel 1
for the charger temperature. Given that all trogdor boards have
the charger thermistor it makes more sense to use channel 0,
and then let boards with other thermistors use channels 1, 2, 3,
rather than 0, 2, 3.
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/20210225103330.v2.4.I67e29f2854bad22e3581d6a6e1879b9fc8abbdea@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
The trip point configuration of the charger thermal zone for trogdor
is missing a node for the critical trip point. Add the missing node.
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Fixes: bb06eb3607e9 ("arm64: qcom: sc7180: trogdor: Add ADC nodes and thermal zone for charger thermistor")
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/20210225103330.v2.3.Ife7768b6b4765026c9d233ad4982da0e365ddbca@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Lazor is stuffed with a 47k NTC as thermistor for the charger
temperature which currently isn't supported by the PM6150 ADC
driver. Disable the charger thermal zone to avoid the use of
bogus temperature values.
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/20210225103330.v2.2.Ia4c1022191d09fe8c56a16486b77796b83ffcae4@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Some revisions of trogdor boards use a thermistor for the charger
temperature which currently isn't supported by the PM6150 ADC
driver. This results in bogus temperature readings. Add a label
to the charger thermal zone to facilitate disabling of the thermal
zone on affected boards.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20210225103330.v2.1.I6a426324db3d98d6cfae8adf2598831bb30bba74@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Add support for two Siemens SIMATIC IOT2050 variants, Basic and
Advanced. They are based on the TI AM6528 GP and AM6548 SOCs HS, thus
differ in their number of cores and availability of security features.
Furthermore the Advanced version comes with more RAM, an eMMC and a few
internal differences.
Based on original version by Le Jin.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://new.siemens.com/global/en/products/automation/pc-based/iot-gateways/simatic-iot2050.html
Link: https://github.com/siemens/meta-iot2050
Link: https://lore.kernel.org/r/4fb05969102d14d230e03ca4312ef9706efa61e6.1615473223.git.jan.kiszka@siemens.com
|
|
These boards are based on AM6528 GP and AM6548 HS SOCs.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/173ce7d928ed9f352af7673dd44c6c76a1466eb5.1615473223.git.jan.kiszka@siemens.com
|
|
Add prefix for Siemens AG.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/4750c25ded8d1d5791c14b0e7b450a2a918eea36.1615473223.git.jan.kiszka@siemens.com
|
|
Add pinmux details and device tree node for the EEPROM attached to SPI0
module in main domain.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20210309162315.22743-1-a-govindraju@ti.com
|
|
TI J7200 has the Cadence OSPI controller for interfacing with OSPI
flashes. Add its node to allow using SPI flashes.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20210305153926.3479-4-p.yadav@ti.com
|
|
Set the Tx bus width to 8 so 8D-8D-8D mode can be selected. Change the
frequency to 25 MHz. This is the frequency that the flash has been
successfully tested with in Octal DTR mode. The total performance should
still increase since 8D-8D-8D mode should be at least twice as fast as
1S-1S-8S mode.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20210305153926.3479-3-p.yadav@ti.com
|
|
Set the Tx bus width to 8 so 8D-8D-8D mode can be selected. Change the
frequency to 25 MHz. This is the frequency that the flash has been
successfully tested with in Octal DTR mode. The total performance should
still increase since 8D-8D-8D mode should be at least twice as fast as
1S-1S-8S mode.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20210305153926.3479-2-p.yadav@ti.com
|
|
itap delay values for MMCSD subsystems
According to latest errata of J721e [1], HS400 mode is not supported
in MMCSD0 subsystem (i2024) and SDR104 mode is not supported in MMCSD1/2
subsystems (i2090). Therefore, replace mmc-hs400-1_8v with mmc-hs200-1_8v
in MMCSD0 subsystem and add a sdhci mask to disable SDR104 speed mode.
Also, update the itap delay values for all the MMCSD subsystems according
the latest J721e data sheet[2]
[1] - https://www.ti.com/lit/er/sprz455/sprz455.pdf
[2] - https://www.ti.com/lit/ds/symlink/tda4vm.pdf
Fixes: cd48ce86a4d0 ("arm64: dts: ti: k3-j721e-common-proc-board: Add support for SD card UHS modes")
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Kishon Vijay Abraham I <kishon@ti.com>
Link: https://lore.kernel.org/r/20210305054104.10153-1-a-govindraju@ti.com
|
|
Add the DT entry for a watchdog based on RTI1.
On SR1.0 silicon, it requires additional firmware on the MCU R5F cores
to handle the expiry, e.g. https://github.com/siemens/k3-rti-wdt. As
this firmware will also lock the power domain to protect it against
premature shutdown, mark it shared.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Praneeth Bajjuri <praneeth@ti.com>
Link: https://lore.kernel.org/r/279c20fa-6e5e-4f88-9cd1-f76297a28a19@web.de
|
