| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The S5M8767 PMIC does not require anymore a safe DVS voltage, if the DVS
GPIO is not enabled. Although previously bindings required providing
this safe DVS voltage, but since commit 04f9f068a619 ("regulator:
s5m8767: Modify parsing method of the voltage table of buck2/3/4") this
was ignored.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20210928084949.27939-12-krzysztof.kozlowski@canonical.com
|
|
There are couple of revisions of SOMs (k26) and associated carrier cards
(kv260).
SOM itself has two major versions:
sm-k26 - SOM with EMMC
smk-k26 - SOM without EMMC used on starter kit with preprogrammed firmware
in QSPI.
SOMs are describing only devices available on the SOM or connections which
are described in specification (for example UART, fwuen).
When SOM boots out of QSPI it uses limited number of peripherals defined by
the specification and present in sm(k)-k26 dtses.
Then a carrier card (CC) detection is happening and DT overlay is applied
to brings new functionality. That's why DT overlays are used. The name is
composed together with SOM name and CC name that's why DT overlays with
these names are generated to make sure they can be used together.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/1ba32590670434b650bacf6410a65579dd30b38b.1632294439.git.michal.simek@xilinx.com
|
|
29.5V (29p5) is obviously wrong for regulator l4 and l5. Correct them
to be 2.95V (2p95). No functional change.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210926072215.27517-1-shawn.guo@linaro.org
|
|
Some multiline properties (spread out over multiple lines to keep length
in check) were not indented properly, leading to misalignment with the
items above. The DT file is still small enough to address this early in
the process.
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Martin Botka <martin.botka@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210925141841.407257-1-marijn.suijten@somainline.org
|
|
At the moment, longcheer-l8150 is using a dummy extcon-usb-gpio device
that permanently enables USB gadget mode. This workaround allows USB
to work but is actually wrong and confusing. The "vbus-gpio" used there
refers to an unused (floating) GPIO that is pulled up to make
extcon-usb-gpio report USB gadget mode permanently.
Replace this with the new &pm8916_usbin extcon device that actually
reports if an USB cable is attached or not. This allows the USB PHY
to be turned off when there is no USB cable attached and is much
cleaner overall.
Fixes: 16e8e8072108 ("arm64: dts: qcom: Add device tree for Longcheer L8150")
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210928112945.25310-3-stephan@gerhold.net
|
|
At the moment, USB gadget mode on MSM8916 works only with an extcon
device that reports the correct USB mode. This might be because the
USB PHY needs to be configured appropriately.
Unfortunately there is currently no simple approach to get such an
extcon device during early bring-up. The extcon device for USB VBUS
(i.e. gadget/peripheral mode) is typically provided by the charging
driver which is almost always very complex to port.
On pretty much all devices with PM8916, the USB VBUS is also connected
to the PM8916 "USB_IN" pad, no matter if they use the linear charger
integrated into PM8916 or not. The state of this pad can be checked
with the "USBIN_VALID" interrupt of PM8916.
The "qcom,pm8941-misc" binding exists to expose an "usb_vbus" and/or
"usb_id" interrupt from the PMIC as an extcon device.
Add a &pm8916_usbin node to pm8916.dtsi which can be used as simple
extcon device for devices that are currently lacking a proper charger
driver.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210928112945.25310-2-stephan@gerhold.net
|
|
While removing the size from the "reg" properties in pm8916.dtsi,
commit bd6429e81010 ("ARM64: dts: qcom: Remove size elements from
pmic reg properties") mistakenly also removed the second register
address for the rtc@6000 device. That one did not represent the size
of the register region but actually the address of the second "alarm"
register region of the rtc@6000 device.
Now there are "reg-names" for two "reg" elements, but there is actually
only one "reg" listed.
Since the DT schema for "qcom,pm8941-rtc" only expects one "reg"
element anyway, just drop the "reg-names" entirely to fix this.
Fixes: bd6429e81010 ("ARM64: dts: qcom: Remove size elements from pmic reg properties")
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210928112945.25310-1-stephan@gerhold.net
|
|
Describe all Ethernet PHY reset GPIOs on R-Car Gen3 boards, to avoid
relying solely on boot loaders to bring PHYs out of reset.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/3e6fd765850e8ef0980d8e98bc5f2126538d626f.1631177442.git.geert+renesas@glider.be
|
|
Describe all Ethernet PHY reset GPIOs on RZ/G1 boards, to avoid relying
solely on boot loaders to bring PHYs out of reset.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/e20b3643b4dc5f6c2a9e19d9544495c06075d9ff.1631177442.git.geert+renesas@glider.be
|
|
Describe all Ethernet PHY reset GPIOs on R-Mobile boards, to avoid
relying solely on boot loaders to bring PHYs out of reset.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/b41bf0098ff193fbff9fad04d00075ce1bea1986.1631177442.git.geert+renesas@glider.be
|
|
Add compatible values to Ethernet PHY subnodes representing Realtek
RTL8211E PHYs on RZ/G2 boards. This allows software to identify the PHY
model at any time, regardless of the state of the PHY reset line.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/3b366e3dddd4d3cd7e89b92d3a8f78f6dc18e244.1631174218.git.geert+renesas@glider.be
|
|
Add compatible values to Ethernet PHY subnodes representing Micrel
KSZ9031 PHYs on R-Car Gen3 boards. This allows software to identify the
PHY model at any time, regardless of the state of the PHY reset line.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/07bd7e04dda9e84cde0664980f0b1a6d69e03109.1631174218.git.geert+renesas@glider.be
|
|
Add compatible values to Ethernet PHY subnodes representing Atheros
AR8031 PHYs on RZ/G2 boards. This allows software to identify the PHY
model at any time, regardless of the state of the PHY reset line.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Adam Ford <aford173@gmail.com>
Link: https://lore.kernel.org/r/3f1b58756f149f0c634c66abaecc88e699f4c3cc.1631174218.git.geert+renesas@glider.be
|
|
Add compatible values to Ethernet PHY subnodes representing Renesas
uPD60610 or uPD60611 PHYs on RZ/A1 boards. This allows software to
identify the PHY model at any time, regardless of the state of the PHY
reset line.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/335a1dfea905369da683e122e41e08ca1c5f90f7.1631174218.git.geert+renesas@glider.be
|
|
Add compatible values to Ethernet PHY subnodes representing Realtek
RTL8201FL PHYs on RZ/A2 boards. This allows software to identify the
PHY model at any time, regardless of the state of the PHY reset line.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/a23eca16869457684b0300379233e335b4e2047e.1631174218.git.geert+renesas@glider.be
|
|
Add compatible values to Ethernet PHY subnodes representing SMSC
LAN8710A PHYs on RZ/A1 and R-Mobile A1 boards. This allows software to
identify the PHY model at any time, regardless of the state of the PHY
reset line.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/247dc2074dae149af07b6d014985ad30eb362eda.1631174218.git.geert+renesas@glider.be
|
|
Add compatible values to Ethernet PHY subnodes representing Micrel
KSZ9031 PHYs on RZ/G1 boards. This allows software to identify the PHY
model at any time, regardless of the state of the PHY reset line.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/ce8ae6b199fa244315a008ae31891a808ca1948d.1631174218.git.geert+renesas@glider.be
|
|
Add compatible values to Ethernet PHY subnodes representing Micrel
KSZ8081 PHYs on RZ/G1 boards. This allows software to identify the PHY
model at any time, regardless of the state of the PHY reset line.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/ec5c7dadf3c0fe5e47dfbae72fb435047203ad06.1631174218.git.geert+renesas@glider.be
|
|
Add compatible values to Ethernet PHY subnodes representing Micrel
KSZ8041 PHYs on RZ/G1 and R-Car Gen2 boards. This allows software to
identify the PHY model at any time, regardless of the state of the PHY
reset line.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/f9e26625924f90eff34fe6f6f02b15fa272c5d80.1631174218.git.geert+renesas@glider.be
|
|
While networking works fine in RGMII mode when using the Linux generic
PHY driver, it fails when using the Atheros PHY driver.
Fix this by correcting the Ethernet PHY mode to RGMII-RXID, which works
fine with both drivers.
Fixes: a5200e63af57d05e ("arm64: dts: renesas: rzg2: Convert EtherAVB to explicit delay handling")
Reported-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/2a4c15b2df23bb63f15abf9dfb88860477f4f523.1632465965.git.geert+renesas@glider.be
|
|
According to schematics, and confirmed by ID_REV register contents, the
Ethernet controllers on various development board are not SMSC LAN9220,
but different variants:
- KZM-A9-Dual and KZM-A9-GT: LAN9221,
- Bock-W and Marzen: LAN89218AQ.
Update the compatible values accordingly.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/59c142176f795b3541c935df43ab11cecd77cc61.1631173813.git.geert+renesas@glider.be
|
|
Update MSS node to support MSA based modem boot on SC7280 SoCs.
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/1631886935-14691-11-git-send-email-sibis@codeaurora.org
|
|
This patch adds Q6V5 MSS PAS remoteproc node for SC7280 SoCs.
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/1631886935-14691-10-git-send-email-sibis@codeaurora.org
|
|
Add miscellaneous nodes to boot the modem and support post-mortem debug
on SC7280 SoCs.
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/1631886935-14691-9-git-send-email-sibis@codeaurora.org
|
|
Add, delete and update platform specific reserved memory nodes.
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/1631886935-14691-8-git-send-email-sibis@codeaurora.org
|
|
Add missing reserved regions as described in v1 of SC7280 memory map.
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/1631886935-14691-7-git-send-email-sibis@codeaurora.org
|
|
This device has a physical matrix keyboard, connected to a GPIO
expander, for which there's still no support yet.
Though, some of the keys are connected to the MSM8998 GPIOs and not
as a matrix, so these can be added.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210909123823.368199-4-angelogioacchino.delregno@somainline.org
|
|
This smartphone has a Goodix GT8296 touch IC, reachable at address
0x14 on blsp2 i2c-1.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210909123823.368199-3-angelogioacchino.delregno@somainline.org
|
|
Add configuration for the physical keyboard LEDs, including the
caps lock indicator and keyboard backlight.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210909123823.368199-2-angelogioacchino.delregno@somainline.org
|
|
Add device tree support for the F(x)tec Pro 1 (QX1000) smartphone;
this is a minimal configuration to boot to serial console.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210909123823.368199-1-angelogioacchino.delregno@somainline.org
|
|
At the moment, playing audio on Secondary MI2S will just end up getting
stuck, without actually playing any audio. This happens because the wrong
bit clock is configured when playing audio on Secondary MI2S.
The PRI_I2S_CLK (better name: SPKR_I2S_CLK) is used by the SPKR audio mux
block that provides both Primary and Secondary MI2S.
The SEC_I2S_CLK (better name: MIC_I2S_CLK) is used by the MIC audio mux
block that provides Tertiary MI2S. Quaternary MI2S is also part of the
MIC audio mux but has its own clock (AUX_I2S_CLK).
This means that (quite confusingly) the SEC_I2S_CLK is not actually
used for Secondary MI2S as the name would suggest. Secondary MI2S
needs to have the same clock as Primary MI2S configured.
Fix the clock list for the lpass node in the device tree and add
a comment to clarify this confusing naming. With these changes,
audio can be played correctly on Secondary MI2S.
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Fixes: 3761a3618f55 ("arm64: dts: qcom: add lpass node")
Tested-by: Vincent Knecht <vincent.knecht@mailoo.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210816181810.2242-1-stephan@gerhold.net
|
|
So far there were no interrupts set up for the BMC150 accelerometer
+ magnetometer combo because they were broken for some reason.
It turns out Longcheer L8150 actually has a BMC156 which is very similar
to BMC150, but only has an INT2 pin for the accelerometer part.
This requires some minor changes in the bmc150-accel driver which is now
supported by using the more correct bosch,bmc156_accel compatible.
Unfortunately it looks like even INT2 is not functional on most boards
because the interrupt line is not actually connected to the BMC156.
However, there are two pads next to the chip that can be shorted
to make it work if needed.
While at it, add the missing interrupts for the magnetometer part
and extra BMG160 gyroscope, those seem to work without any problems.
Also correct the magnetometer compatible to bosch,bmc156_magn for clarity
(no functional difference for the magnetometer part).
Tested-by: Nikita Travkin <nikita@trvn.ru>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210816123544.14027-1-stephan@gerhold.net
|
|
Add IMEM and pil info DT nodes for SC7180 SoC which will help in the
post-mortem debug.
Signed-off-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
[bjorn: Dropped dload-mode subnode, as no agreement was reached on this binding]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/39064a2db95ccc2cb5eef003569bef2de651c8ed.1628757036.git.saiprakash.ranjan@codeaurora.org
|
|
Add missing include to make it compile.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210923162204.21752-17-konrad.dybcio@somainline.org
|
|
Add initial SM6350 SoC and Sony Xperia 10 III (PDX213, Lena platform) device
trees. There is no sign of another Lena devices on the horizon, so a common
DTSI is not created for now. 10 III features a Full HD OLED display and 5G
support, among other nice things like USB3.
The bootloader is VERY unpleasant, to get a bootable setup you have to run:
mkbootimg --kernel arch/arm64/boot/Image.gz --ramdisk [some initrd] \
--dtb arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dtb \
--cmdline "[some cmdline]" --base 0 --kernel_offset 0x8000 \
--ramdisk_offset 0x1000000 --dtb_offset 0x1f00000 --os_version 11 \
--os_patch_level "2021-08" --tags_offset 0x100 --pagesize 4096 \
--header_version 2 -o mainline.img
adb reboot bootloader
// You have to either pull vbmeta{"","_system"} from
// /dev/block/bootdevice/by-name/ or build one as a part of AOSP build process
fastboot --disable-verity --disable-verification flash vbmeta vbmeta.img
fastboot --disable-verity --disable-verification flash vbmeta_system \
vbmeta_system.img
fastboot flash boot mainline.img
fastboot erase dtbo // This will take approx 70s...
fastboot reboot
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210923162204.21752-16-konrad.dybcio@somainline.org
|
|
Add a node for the APPS SMMU to allow for managing memory access to peripherals
such as the USB controller.
While at it, add iommus property to the USB1 node to make sure its registers can
be accessed, as they seem to be gated by default.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210923162204.21752-15-konrad.dybcio@somainline.org
|
|
Add SDHCI1/2 nodes for eMMC and uSD card respectively.
Do note that most SM6350 devices seem to come with UFS.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
[bjorn: Replaced SM6350_CX with its constant value]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210923162204.21752-14-konrad.dybcio@somainline.org
|
|
Add RPMHPD node, its OPP table and BCM voter to prepare for performance level
voting.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210923162204.21752-13-konrad.dybcio@somainline.org
|
|
Add a node for the PRNG to enable hw-accelerated pseudo-random number
generation.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210923162204.21752-12-konrad.dybcio@somainline.org
|
|
Add a node for SPMI to allow for communication with on-board PMICs.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210923162204.21752-11-konrad.dybcio@somainline.org
|
|
Add a node for AOSS_QMP in preparation for remote processor enablement.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210923162204.21752-10-konrad.dybcio@somainline.org
|
|
Add nodes required for TSENS block using the common qcom,tsens-v2 binding.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210923162204.21752-9-konrad.dybcio@somainline.org
|
|
Add cpufreq-hw node and assign qcom,freq-domain properties to CPUs to enable
CPU clock scaling.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210923162204.21752-8-konrad.dybcio@somainline.org
|
|
Add nodes required for USB1 to function. SM6350 (thankfully) resuses SDM845 and
SC7180 IP, so no additional code porting is required.
Acked-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
[bjorn: Renamed dwc3 node "usb"]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210923162204.21752-7-konrad.dybcio@somainline.org
|
|
Add TLMM pinctrl node to enable referencing the SoC pins in other nodes.
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210923162204.21752-6-konrad.dybcio@somainline.org
|
|
Add and configure GCC node to allow for referencing GCC-controlled clocks
in other nodes.
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210923162204.21752-5-konrad.dybcio@somainline.org
|
|
Add RPMHCC node to allow for referencing RPMH-controlled clocks in other
nodes.
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210923162204.21752-4-konrad.dybcio@somainline.org
|
|
Add a node for LLCC with SM6350-specific compatible.
Acked-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210923162204.21752-3-konrad.dybcio@somainline.org
|
|
Add a base DT for SM6350 SoC
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210923162204.21752-2-konrad.dybcio@somainline.org
|
|
Document Kryo 560 CPUs found in Qualcomm Snapdragon 690 (SM6350).
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210923162204.21752-1-konrad.dybcio@somainline.org
|
