| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
PioD controller was not described in the device tree since we don't use
it. As pinctrl-at91 allows disabled gpio controllers in the device
tree, we can add it to complete the device description.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
Add an hdmi node, and also add hdmi endpoints to vopb and vopl
output port nodes.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Tested-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Add devicetree nodes for rk3288 VOP (Video Output Processors), and the
top level display-subsystem root node.
Later patches add endpoints (eDP, HDMI, LVDS, etc) that attach to the
VOPs' output ports.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Mark yao <mark.yao@rock-chips.com>
Reviewed-by: Stephane Marchesin <marcheu@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Adds a new id for the pclk supplying the watchdog on rk3288 socs.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Doug Anderson <dianders@chromium.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/galak/linux-qcom into next/dt
Merge "qcom DT changes for v3.20" from Kumar Gala:
Qualcomm ARM Based Device Tree Updates for v3.20
* Correct IPQ8064 tlmm interrupt
* Add Support for SD Card Detect for ifc6410 board
* tag 'qcom-dt-for-3.20' of git://git.kernel.org/pub/scm/linux/kernel/git/galak/linux-qcom:
ARM: dts: qcom: Correct IPQ8064 tlmm interrupt
ARM: dts: qcom: Add Support for SD Card Detect for ifc6410 board
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Merge "Second Round of Renesas ARM Based SoC DT Updates for v3.20" from Simon
Horman:
* Support Renesas memory controllers
* Add SRC interrupt number on r8a779~ and r8a7791 SoCs
* Fix MSTP8 input clocks on r8a7791 SoC
* Add PM domain support to r8a7740
* Add DT bindings for the R-Mobile System Controller
* Use Add sh73a0-specific FSI2 compatible property
* tag 'renesas-dt2-for-v3.20' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
PM / Domains: R-Mobile SYSC: Document SH-Mobile AG5 (sh73a0) binding
ARM: shmobile: sh73a0 dtsi: Add memory-controller nodes
ARM: shmobile: r8a7740 dtsi: Add memory-controller node
ARM: shmobile: r8a73a4 dtsi: Add memory-controller nodes
ARM: shmobile: Add DT bindings for Renesas memory controllers
ARM: shmobile: r8a7791: add SRC interrupt number on DTSI
ARM: shmobile: r8a7790: add SRC interrupt number on DTSI
ARM: shmobile: r8a7791: fix MSTP8 input clocks
ARM: shmobile: r8a7740 dtsi: Add PM domain support
PM / Domains: Add DT bindings for the R-Mobile System Controller
ARM: shmobile: sh73a0 dtsi: Add SoC-specific FSI2 compatible property
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Merge "omap device tree changes for v3.20" from Tony Lindgren:
Device tree changes for omaps. Mostly to add support for new
am437x-idk and update am437x-sk boards. Also enabling new
devices for multiple boards.
* tag 'omap-for-v3.20/dt-pt1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (21 commits)
ARM: dts: omap3-gta04: Add handling for tv output
ARM: dts: cm-t3x: add NAND support
ARM: dts: am57xx-beagle-x15: Add GPIO controlled fan node
ARM: dts: am437x-idk: add gpio-based power key
ARM: dts: N950/N9: add twl_power
ARM: dts: am437x-sk: add power button binding
ARM: dts: add support for AM437x IDK
ARM: dts: am437x-gp-evm: add VPFE device tree data
ARM: dts: am437x-sk-evm: add VPFE device tree data
ARM: dts: am43x-epos-evm: add VPFE device tree data
ARM: dts: am4372: add VPFE DT node entries
ARM: dts: DRA7X: drop id property in pcie_phy
ARM: dts: omap3-n900: cleanup english
ARM: dts: am57xx-beagle-x15: Add dual ethernet
ARM: dts: am437x-sk: remove DSS pulls
ARM: dts: am437x-sk: remove internal i2c pullups
ARM: dts: am437x-sk: add explicit pinmux for both USB instances
ARM: dts: am437x-sk: remove ethernet pulls
ARM: dts: am437x-sk: add explicit MMC0 pinmux
ARM: dts: am437x-sk: remove internal pulls from QSPI
...
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
The Kconfig symbol DEBUG_MVEBU_UART_ALTERNATE was renamed to
DEBUG_MVEBU_UART0_ALTERNATE. And the symbol DEBUG_MVEBU_UART1_ALTERNATE
was added to allow UART1 as a DEBUG_LL target. Make the comment at the
top of this DTS reflect those changes.
Since we're touching this DTS add comments to show which blocks describe
UART0 and UART1.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
|
|
Add the regulators to each SATA port.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
The pogoplug differs from the SheevaPlug only by a
few details, but especially in the led assignments.
This patch was tested under Gentoo Linux and is
based on dts files from Arch Linux ARM and OpenWrt.
Suggested-by: Felix Kaechele <heffer@fedoraproject.org>
Suggested-by: Oleg Rakhmanov <moonman.ca@gmail.com>
Signed-off-by: Christoph Junghans <ottxor@gentoo.org>
[Andrew Lunn <andrew@lunn.ch>: Fixed subject line]
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
|
|
git://git.stlinux.com/devel/kernel/linux-sti into next/dt
Merge "STi DT updates for v3.20, round 1" from Maxime Coquelin:
Highlights:
-----------
- Add USB support for STiH410 & STiH407
- Add DRM DT nodes for STiH410 & STiH407
- Add STiH418 SoC support
- Add DT nodes for MiPHY28lp PHY
* tag 'sti-dt-for-v3.20-1' of git://git.stlinux.com/devel/kernel/linux-sti:
ARM: DT: STi: STiH407: Add DT node for MiPHY28lp
ARM: dts: STiH418: Add B2199 board support
ARM: dts: Add STiH418 SoC support
ARM: DT: STiH410: Add DRM dt nodes
ARM: DT: STiH407: Add DRM dt nodes
ARM: STi: DT: STiH410: Add DT nodes for the ehci and ohci usb controllers.
ARM: STi: DT: STiH410: Add usb2 picophy dt nodes
ARM: STi: DT: STiH407: Add usb2 picophy dt nodes
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Add dts file for Hisilicon hip01 ca9x2 board
Signed-off-by: Wang Long <long.wanglong@huawei.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
[olof: Folded in smp enable-method from a different patch]
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
This patch add support for Marsboard A10 board.
The Marsboard A10 is a A10 based development board with 1G RAM, 1G NAND,
micro SD card slot, SATA 2.0 socket, 10/100 ethernet, mini HDMI port,
1 USB OTG port and 2 USB 2.0 ports. Board does not use the AXP209 pmic,
it does not have a pmic at all.
Board also have 2 expansion 70 pin headers.
Signed-off-by: Aleksei Mamlin <mamlinav@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The A80 Optimus Board has a 16GB eMMC connected to mmc2, with 8 bit
wide data bus.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
mmc2 is available on port C. Add a pinmux setting for 8 bit wide eMMC.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Enable the micro-sd slot on the A80 Optimus Board, which is connected to
mmc0. This adds the card-detect gpio and enables mmc0.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The preferred method of referencing nodes from the dtsi is to use
labels, instead of copying the complete tree.
This patch converts sun9i-a80-optimus.dts to use label references.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The A80 has 4 mmc controllers.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Add the device tree nodes for the mmc config clock nodes.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
This patch add missing mdio label for sun[457]i.
Signed-off-by: Aleksei Mamlin <mamlinav@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The mk802_a10s re-uses is the "classic" mk802 case and functionality, but has
an A10s SoC inside rather then the A10, it features 512M or 1G RAM, 4G nand,
a mini-hdmi female connector, USB-A receptacle, mini-usb receptacle (OTG)
and a sdio realtek wifi chip. Unlike the original mk802 it does have a pmic,
the axp152.
For more details see: http://linux-sunxi.org/Semitime_g2
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
[Maxime: Changed the compatible and node names labels]
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The mk802ii is a revised version of the mk802 A10 based hdmi tv-stick, it
features 1G RAM, 4G nand, a hdmi male connector, USB-A receptacle, 2 micro
usb receptacles (OTG & power) and USB-wifi, and does come with an axp209 pmic.
For more details see: http://linux-sunxi.org/Rikomagic_mk802ii
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The mk802 is the "classic" Allwinner A10 based hdmi tv-stick, it features
512M or 1G RAM, 4G nand, a mini-hdmi female connector, USB-A receptacle,
mini-usb receptacle (OTG) and USB-wifi. Somewhat unique the mk802 does not
use the AXP209 pmic, it does not have a pmic at all.
For more details see: http://linux-sunxi.org/Rikomagic_mk802
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The Chuwi V7 is an A10 (sun4i) based tablet with 1G of RAM, 16G of nand flash,
microsd slot, 7" 1024x768 lvds ips panel, mini hdmi out, headphones out,
stereo speakers, front & back camera and usb wifi.
It is clearly marked "CHUWI", "V7" and "Model: CW0825" on the back of the
tablet.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Add support for the new Bananapro A20 development board from lemaker.org.
This board features 1G RAM, 2 USB A receptacles, 1 micro USB receptacle for
OTG, 1 micro USB receptacle for power, HDMI, sata, Gbit ethernet, ir receiver,
3.5 mm jack for a/v out, on board microphone, 40 gpio pins and sdio wifi.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The A31 has non-initialized architected timers, without CNTFRQ or CNTVOFF set
by the Allwinner's bootloader.
Use the new DT property for such case, and enable the arch timers.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Using label references is preferred when override settings from the
included dtsi.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
mmc0 is only available on port F, and is always used with a 4 bit wide
bus for the onboard micro-sd slot.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Use the label to reference the pin controller node, so that we can use
sunxi-common-regulators with sunxi families that don't share the same
address space mappings, such as sun9i.
This patch is mostly space changes due to the reduction of node parents.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
of_clk_get_parent_name() uses the clock-indices property to resolve
clock phandle arguments in case that the argument index does not
match the clock-output-names sequence.
This is the case on sunxi, where we use the actual bit index as the
argument to the phandle. Add the clock-indices property so that
of_clk_get_parent_name() resolves the names correctly.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The mmc module clocks are A80 specific module 0 (storage) type clocks.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The current GPL only licensing on the DTSI makes it very impractical for other
software components licensed under another license.
In order to make it easier for them to reuse our device trees, relicense our
device trees under a GPL/X11 dual-license.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Alexander Bersenev <bay@hackerdom.ru>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Carlo Caione <carlo@caione.org>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Olliver Schinagl <oliver@schinagl.nl>
|
|
The current GPL only licensing on the DTSI makes it very impractical for other
software components licensed under another license.
In order to make it easier for them to reuse our device trees, relicense our
device trees under a GPL/X11 dual-license.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Alexander Bersenev <bay@hackerdom.ru>
Acked-by: Carlo Caione <carlo@caione.org>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Roman Byshko <rbyshko@gmail.com>
|
|
The Ippo Q8H v1.2 is almost identical to the v5, still it needs a separate
dtb file since some gpio-s surrounding the wlan/bluetooth are different,
it uses different camera sensors, and different DRAM timings.
Note that atm neither the wlan/bluetooth nor the camera are supported, so
atm their is no difference between the dts files, but because of the different
DRAM timings there are already separate u-boot configs for the 2 different
versions, and the 1.2 config refers to sun8i-a23-ippo-q8h-v1.2.dtb to be
future proof, so we need to provide a sun8i-a23-ippo-q8h-v1.2.dtb file.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The a23-ippo-q8h tablets have volume up/down buttons using the lradc. This
has been tested on both a v5 and a v1.2 tablet.
Tested-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The A23 has the same lradc controller as previous Allwinner SoCs.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
This patch adds the regulator nodes for the axp209 by including
the axp209 dtsi. As the inputs of these regulators are from the
axp209's PS output, which is basically just a mux over the 2
inputs, it is considered to be unregulated. Thus we do not provide
input supply properties for them.
The regulator names and constraints are based on the board
schematics and the SoC datasheet.
DCDC2 is used as the cpu power supply. This patch also references
it from the cpu node.
Also get rid of axp209 properties already set in axp209.dtsi.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
This patch adds the regulator nodes for the axp209 by including
the axp209 dtsi. As the inputs of these regulators are from the
axp209's PS output, which is basically just a mux over the 2
inputs, it is considered to be unregulated. Thus we do not provide
input supply properties for them.
The regulator names and constraints are based on the board
schematics and the SoC datasheet.
DCDC2 is used as the cpu power supply. This patch also references
it from the cpu node.
LDO3 powers the USB WiFi module. This patch also references it
from the usb-phy node.
Also get rid of axp209 properties already set in axp209.dtsi.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
This patch adds the regulator nodes for the axp209 by including
the axp209 dtsi. As the inputs of these regulators are from the
axp209's PS output, which is basically just a mux over the 2
inputs, it is considered to be unregulated. Thus we do not provide
input supply properties for them.
The regulator names and constraints are based on the board
schematics and the SoC datasheet.
DCDC2 is used as the cpu power supply. This patch also references
it from the cpu node.
Also get rid of axp209 properties already set in axp209.dtsi.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
This patch adds the regulator nodes for the axp209 by including
the axp209 dtsi. As the inputs of these regulators are from the
axp209's PS output, which is basically just a mux over the 2
inputs, it is considered to be unregulated. Thus we do not provide
input supply properties for them.
The regulator names and constraints are based on the board
schematics and the SoC datasheet.
DCDC2 is used as the cpu power supply. This patch also references
it from the cpu node.
Also get rid of axp209 properties already set in axp209.dtsi.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The core temperature sensor now supports thermal zones. Add a thermal
zone mapping for the cpus with passive cooling (cpufreq throttling).
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The core temperature sensor now supports thermal zones. Add a thermal
zone mapping for the cpus with passive cooling (cpufreq throttling).
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The core temperature sensor now supports thermal zones. Add a thermal
zone mapping for the cpus with passive cooling (cpufreq throttling).
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The AXP209 PMIC is used with some Allwinner SoCs. This patch adds
a dtsi file listing all the regulator nodes. The regulators are
initialized based on their device node names.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The pcDuino board has LEDs connected to PH15/PH16, and back/home/menu
buttons to PH17/18/19 respectively. Enable these via gpio-leds and
gpio-keys. This is shared across the v1 and v2 versions of the board.
Tested on a v2 and verified against the schematics of a v1.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Acked-by: Hans de Goede <hdegoede@redhat.com>
[Maxime: Added some newlines between the button nodes]
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Add simplefb nodes for "[de_fe0-]de_be0-lcd0" and "[de_fe0-]de_be0-lcd0-tve0"
display pipelines for when u-boot has set up a pipeline to drive a LCD panel /
VGA output rather then the HDMI output.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The cpu core is clocked from the "cpu" clock. Add a reference to it
in the first cpu node. Also add "cpu0" label to the node.
The operating points were taken from the A10 FEX files in the
sunxi-boards repository. All FEX files have the same settings.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The cpu core is clocked from the "cpu" clock. Add a reference to it
in the first cpu node. Also add "cpu0" label to the node.
The operating points were taken from the A13 FEX files in the
sunxi-boards repository. All FEX files have the same settings.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The cpu core is clocked from the "cpu" clock. Add a reference to it
in the first cpu node. Also add "cpu0" label to the node.
The operating points were taken from the A20 FEX files in the
sunxi-boards repository. Not all boards have the same settings. The
settings in this patch are the most generic ones.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Now that the resistive touchpanel driver supports thermal sensors,
add the "#thermal-sensor-cells" property as required by the thermal
framework.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
