| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Commit 56550d94cbaeaa19 ("Drivers: gpu: remove __dev* attributes.")
forgot to realign the continuation of the parameter section of
shmob_drm_setup_clocks().
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/b1c5c9b33b74fef1f4250847398a98f93c4dc1be.1694767209.git.geert+renesas@glider.be
|
|
The SH-Mobile LCD Controller is part of a PM Domain on all relevant SoCs
(clock domain on all, power domain on some). Hence it may not be
sufficient to manage the LCDC module clock explicitly (e.g. if the
selected clock source differs from SHMOB_DRM_CLK_BUS).
Fix this by using Runtime PM for all clock handling. Add an explicit
dependency on CONFIG_PM, which should already be met on all affected
platforms.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/e7359a64963bd9a4f1531c2beae850774ce140bc.1694767209.git.geert+renesas@glider.be
|
|
The first encoder output on the SH-Mobile LCD Controller is a DPI
parallel bus. However, at the time of introduction of the driver, no
encoder or connector types were defined yet for the DPI parallel bus,
hence the driver used the ones for LVDS instead.
Adjust the types accordingly.
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/db500dd8356955d3471a1ccd68d90db9f9750ef9.1694767209.git.geert+renesas@glider.be
|
|
When configuring a CHn Source Image Format Register (LDBBSIFR), one
should use the corresponding LDBBSIFR_RPKF_* definition for overlay
planes, not the DDFR_PKF_* definition for the primary plane.
Fortunately both definitions resolve to the same value, so this bug did
not cause any harm.
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/34f8d51539c048e264699ca869ad9d7a952cd69f.1694767209.git.geert+renesas@glider.be
|
|
Merely writing zero to the CHn Source Image Format Register is not
sufficient to disable a plane, as the programmed register value is not
propagated immediately to the current side. This can be seen when using
the -P option of modetest: the extra plane is displayed correctly, but
does not disappear after exit.
Fix this by doing the full update dance using the Blend Control
Register, like is done when enabling the plane.
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/54e2556e18b5524ce153a7ac79faf2c7b0a55260.1694767209.git.geert+renesas@glider.be
|
|
Add the RGB666 9:9 format MEDIA_BUS_FMT_RGB666_2X9_BE, which is
supported by the SH-Mobile LCD Controller.
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/8b421cc391ac511c07cb1e243c1ba18bb95f7f98.1694767209.git.geert+renesas@glider.be
|
|
Add device tree bindings for the LCD Controller (LCDC) found in Renesas
SuperH SH-Mobile and ARM SH/R-Mobile SOCs.
Based on a plain text prototype by Laurent Pinchart.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/6d0a053502abd6555e9a6cbe055e1bdc3329999d.1694767208.git.geert+renesas@glider.be
|
|
Split off DRM drivers for Renesas SH-Mobile into its own entry, and add
Geert Uytterhoeven as a maintainer.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/7cbcec72214886b67afa8d724a9245661d8cd675.1694767208.git.geert+renesas@glider.be
|
|
If DSI host attachment fails, the LT9611UXC driver will remove the
bridge without ensuring that there is no outstanding HPD work being
done. In rare cases this can result in the warnings regarding the mutex
being incorrect. Fix this by forcebly freing IRQ and flushing the work.
DEBUG_LOCKS_WARN_ON(lock->magic != lock)
WARNING: CPU: 0 PID: 10 at kernel/locking/mutex.c:582 __mutex_lock+0x468/0x77c
Modules linked in:
CPU: 0 PID: 10 Comm: kworker/0:1 Tainted: G U 6.6.0-rc5-next-20231011-gd81f81c2b682-dirty #1206
Hardware name: Qualcomm Technologies, Inc. Robotics RB5 (DT)
Workqueue: events lt9611uxc_hpd_work
pstate: 60400005 (nZCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : __mutex_lock+0x468/0x77c
lr : __mutex_lock+0x468/0x77c
sp : ffff8000800a3c70
x29: ffff8000800a3c70 x28: 0000000000000000 x27: ffffd595fe333000
x26: ffff7c2f0002c005 x25: ffffd595ff1b3000 x24: ffffd595fccda5a0
x23: 0000000000000000 x22: 0000000000000002 x21: ffff7c2f056d91c8
x20: 0000000000000000 x19: ffff7c2f056d91c8 x18: fffffffffffe8db0
x17: 000000040044ffff x16: 005000f2b5503510 x15: 0000000000000000
x14: 000000000006efb8 x13: 0000000000000000 x12: 0000000000000037
x11: 0000000000000001 x10: 0000000000001470 x9 : ffff8000800a3ae0
x8 : ffff7c2f0027f8d0 x7 : ffff7c2f0027e400 x6 : ffffd595fc702b54
x5 : 0000000000000000 x4 : ffff8000800a0000 x3 : 0000000000000000
x2 : 0000000000000000 x1 : 0000000000000000 x0 : ffff7c2f0027e400
Call trace:
__mutex_lock+0x468/0x77c
mutex_lock_nested+0x24/0x30
drm_bridge_hpd_notify+0x2c/0x5c
lt9611uxc_hpd_work+0x6c/0x80
process_one_work+0x1ec/0x51c
worker_thread+0x1ec/0x3e4
kthread+0x120/0x124
ret_from_fork+0x10/0x20
irq event stamp: 15799
hardirqs last enabled at (15799): [<ffffd595fc702ba4>] finish_task_switch.isra.0+0xa8/0x278
hardirqs last disabled at (15798): [<ffffd595fd5a1580>] __schedule+0x7b8/0xbd8
softirqs last enabled at (15794): [<ffffd595fc690698>] __do_softirq+0x498/0x4e0
softirqs last disabled at (15771): [<ffffd595fc69615c>] ____do_softirq+0x10/0x1c
Fixes: bc6fa8676ebb ("drm/bridge/lontium-lt9611uxc: move HPD notification out of IRQ handler")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20231011220002.382422-1-dmitry.baryshkov@linaro.org
|
|
Freescale i.MX93 SoC embeds a Synopsys Designware MIPI DSI host
controller and a Synopsys Designware MIPI DPHY. Some configurations
and extensions to them are controlled by i.MX93 media blk-ctrl.
Add a DRM bridge for i.MX93 MIPI DSI by using existing DW MIPI DSI
bridge helpers and implementing i.MX93 MIPI DSI specific extensions.
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230821034008.3876938-10-victor.liu@nxp.com
|
|
Freescale i.MX93 SoC embeds a Synopsys Designware MIPI DSI host
controller and a Synopsys Designware MIPI DPHY. Some configurations
and extensions to them are controlled by i.MX93 media blk-ctrl.
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230821034008.3876938-9-victor.liu@nxp.com
|
|
According to Synopsys DW MIPI DSI host databook, HSTX and LPRX timeout
contention detections are measured in TO_CLK_DIVISION cycles. However,
the current driver programs magic values to TO_CLK_DIVISION, HSTX_TO_CNT
and LPRX_TO_CNT register fields, which makes timeout error event wrongly
happen for some video modes, at least for the typical 1920x1080p@60 video
mode read from a HDMI monitor driven by ADV7535 DSI to HDMI bridge.
While at it, the current driver doesn't enable interrupt to handle or
complain about the error status, so true error just happens silently
except for display distortions by visual check.
Disable the timeout check by setting those timeout register fields to
zero for now until someone comes along with better computations for the
timeout values. Although the databook doesn't mention what happens when
they are set to zero, it turns out the false error doesn't happen for
the 1920x1080p@60 video mode at least.
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230821034008.3876938-8-victor.liu@nxp.com
|
|
HSA and HBP
According to Synopsys support channel, each region of HSA, HBP and HFP must
have minimum number of 10 bytes where constant 4 bytes are for HSS or HSE
and 6 bytes are for blanking packet(header + CRC). Hence, the below table
comes in.
+------------+----------+-------+
| data lanes | min lbcc | bytes |
+------------+----------+-------+
| 1 | 10 | 1*10 |
+------------+----------+-------+
| 2 | 5 | 2*5 |
+------------+----------+-------+
| 3 | 4 | 3*4 |
+------------+----------+-------+
| 4 | 3 | 4*3 |
+------------+----------+-------+
Implement the minimum lbcc numbers to make sure that the values programmed
into DSI_VID_HSA_TIME and DSI_VID_HBP_TIME registers meet the minimum
number requirement. For DSI_VID_HLINE_TIME register, it seems that the
value programmed should be based on mode->htotal as-is, instead of sum up
HSA, HBP, HFP and HDISPLAY.
This helps the case where Raydium RM67191 DSI panel is connected, since
it's video timing for hsync length is only 2 pixels and without this patch
the programmed value for DSI_VID_HSA_TIME is only 2 with 4 data lanes.
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230821034008.3876938-7-victor.liu@nxp.com
|
|
To get better accuration, use pixel clock rate to calculate lbcc instead of
lane_mbps since the pixel clock rate is in KHz while lane_mbps is in MHz.
Without this, distorted image can be seen on a HDMI monitor connected with
i.MX93 11x11 EVK through ADV7535 DSI to HDMI bridge in 1920x1080p@60 video
mode.
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230821034008.3876938-6-victor.liu@nxp.com
|
|
Vendor drivers may need to fixup mode due to pixel clock tree limitation,
so introduce the ->mode_fixup() callcack to struct dw_mipi_dsi_plat_data
and call it at atomic check stage if available.
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230821034008.3876938-5-victor.liu@nxp.com
|
|
The DATAEN_ACTIVE_LOW bit in DSI_DPI_CFG_POL register is set to zero,
so set the DRM_BUS_FLAG_DE_HIGH flag in input_bus_cfg.flags. It appears
that the DRM_BUS_FLAG_PIXDATA_SAMPLE_NEGEDGE flag also makes sense, so
set it in input_bus_cfg.flags too. With this patch, the flags set by
drm_atomic_bridge_propagate_bus_flags() are overridden (see comment in
that function) in case any downstream bridges propagates invalid flags
to this bridge. A real problematic case is to connect a RM67191 MIPI
DSI panel whose driver sets DRM_BUS_FLAG_DE_LOW and
DRM_BUS_FLAG_PIXDATA_SAMPLE_POSEDGE bus flags.
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230821034008.3876938-4-victor.liu@nxp.com
|
|
Introduce ->get_input_bus_fmts() callback to struct dw_mipi_dsi_plat_data
so that vendor drivers can implement specific methods to get input bus
formats for Synopsys DW MIPI DSI.
While at it, implement a generic callback for ->atomic_get_input_bus_fmts(),
where we try to get the input bus formats through pdata->get_input_bus_fmts()
first. If it's unavailable, fall back to the only format - MEDIA_BUS_FMT_FIXED,
which matches the default behavior if ->atomic_get_input_bus_fmts() is not
implemented as ->atomic_get_input_bus_fmts()'s kerneldoc indicates.
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230821034008.3876938-3-victor.liu@nxp.com
|
|
Add dw_mipi_dsi_get_bridge() helper so that it can be used by vendor
drivers which implement vendor specific extensions to Synopsys DW MIPI DSI.
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230821034008.3876938-2-victor.liu@nxp.com
|
|
As per spec, it is allowed to pulse the HPD signal to indicate that the
EDID information has changed. Some monitors do this when they wake up
from standby or are enabled. When the HPD goes low the adv7511 is
reset and the outputs are disabled which might cause the monitor to
go to standby again. To avoid this we ignore the HPD pin for the
first few seconds after enabling the output. On the other hand,
adv7535 require to enable HPD Override bit for proper HPD.
Add hpd_override_enable variable to struct adv7511_chip_info to handle
this scenario.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230830142358.275459-9-biju.das.jz@bp.renesas.com
|
|
The ADV7511 needs link configuration whereas ADV75{33,35} does not need
it. Add a variable link_config to struct adv7511_chip_info to handle
this difference.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230830142358.275459-8-biju.das.jz@bp.renesas.com
|
|
The ADV7533 and ADV7535 have DSI support. Add a variable has_dsi to
struct adv7511_chip_info for handling configuration related to DSI.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230830142358.275459-7-biju.das.jz@bp.renesas.com
|
|
The ADV7533 and ADV7535 have an offset(0x70) for the CEC register map
compared to ADV7511. Add the reg_cec_offset variable to struct
adv7511_chip_info to handle this difference and drop the reg_cec_offset
variable from struct adv7511.
This will avoid assigning reg_cec_offset based on chip type and also
testing for multiple chip types by calling adv7533_patch_cec_registers().
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230830142358.275459-6-biju.das.jz@bp.renesas.com
|
|
adv7511_chip_info
The ADV7511 has 5 power supplies compared to 7 that of ADV75{33,35}. Add
supply_names and num_supplies variables to struct adv7511_chip_info to
handle this difference.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230830142358.275459-5-biju.das.jz@bp.renesas.com
|
|
The ADV7533 supports a maximum lane clock of 800MHz whereas it is 891MHz
for ADV7535. Add max_lane_freq_khz variable to struct adv7511_chip_info to
handle this difference.
While at it, drop the unused local variable max_lane_freq.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230830142358.275459-4-biju.das.jz@bp.renesas.com
|
|
The ADV7533 supports a maximum pixel clock of 80MHz whereas it is 148.5MHz
for ADV7535. Add max_mode_clock_khz variable to struct adv7511_chip_info to
handle this difference.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Adam Ford <aford173@gmail.com>
Tested-by: Adam Ford <aford173@gmail.com> #imx8mm-beacon
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230830142358.275459-3-biju.das.jz@bp.renesas.com
|
|
Add struct adv7511_chip_info to handle hw differences between various
chips rather checking against the 'type' variable in various places.
Replace 'adv->type'->'info->type' by moving variable 'type' from
struct adv7511 to struct adv7511_chip_info and add adv7511_chip_info as
device data for both OF and ID tables instead of the device type.
Simplify the probe() by replacing of_device_get_match_data() and ID lookup
for retrieving match data with i2c_get_match_data().
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Tested-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230830142358.275459-2-biju.das.jz@bp.renesas.com
|
|
Both the JEDEC and ONFI specification say that read cache sequential
support is an optional command. This means that we not only need to
check whether the individual controller supports the command, we also
need to check the parameter pages for both ONFI and JEDEC NAND flashes
before enabling sequential cache reads.
This fixes support for NAND flashes which don't support enabling cache
reads, i.e. Samsung K9F4G08U0F or Toshiba TC58NVG0S3HTA00.
Sequential cache reads are now only available for ONFI and JEDEC
devices, if individual vendors implement this, it needs to be enabled
per vendor.
Tested on i.MX6Q with a Samsung NAND flash chip that doesn't support
sequential reads.
Fixes: 003fe4b9545b ("mtd: rawnand: Support for sequential cache reads")
Cc: stable@vger.kernel.org
Signed-off-by: Rouven Czerwinski <r.czerwinski@pengutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230922141717.35977-1-r.czerwinski@pengutronix.de
|
|
Update the USB serial option driver support for the Fibocom
FM101R-GL LTE modules as there are actually several different variants.
- VID:PID 413C:8213, FM101R-GL are laptop M.2 cards (with
MBIM interfaces for Linux)
- VID:PID 413C:8215, FM101R-GL ESIM are laptop M.2 cards (with
MBIM interface for Linux)
0x8213: mbim, tty
0x8215: mbim, tty
T: Bus=04 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 2 Spd=5000 MxCh= 0
D: Ver= 3.20 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 9 #Cfgs= 1
P: Vendor=413c ProdID=8213 Rev= 5.04
S: Manufacturer=Fibocom Wireless Inc.
S: Product=Fibocom FM101-GL Module
S: SerialNumber=a3b7cbf0
C:* #Ifs= 3 Cfg#= 1 Atr=a0 MxPwr=896mA
A: FirstIf#= 0 IfCount= 2 Cls=02(comm.) Sub=0e Prot=00
I:* If#= 0 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=0e Prot=00 Driver=cdc_mbim
E: Ad=81(I) Atr=03(Int.) MxPS= 64 Ivl=32ms
I: If#= 1 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
I:* If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
E: Ad=8e(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=0f(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=40 Driver=(none)
E: Ad=83(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=82(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
T: Bus=04 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 3 Spd=5000 MxCh= 0
D: Ver= 3.20 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 9 #Cfgs= 1
P: Vendor=413c ProdID=8215 Rev= 5.04
S: Manufacturer=Fibocom Wireless Inc.
S: Product=Fibocom FM101-GL Module
S: SerialNumber=a3b7cbf0
C:* #Ifs= 3 Cfg#= 1 Atr=a0 MxPwr=896mA
A: FirstIf#= 0 IfCount= 2 Cls=02(comm.) Sub=0e Prot=00
I:* If#= 0 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=0e Prot=00 Driver=cdc_mbim
E: Ad=81(I) Atr=03(Int.) MxPS= 64 Ivl=32ms
I: If#= 1 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
I:* If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
E: Ad=8e(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=0f(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=40 Driver=(none)
E: Ad=83(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=82(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
Signed-off-by: Puliang Lu <puliang.lu@fibocom.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
git://anongit.freedesktop.org/drm/drm-intel into drm-next
drm/i915 feature pull #2 for v6.7:
Features and functionality:
- Preparation for i915 display code reuse in upcoming Xe driver (Jani)
- Drop the fastboot module parameter and use the platform defaults (Arun)
- Enable new LNL FBC features (Vinod)
- Add LNL display feature capability reads (Vinod)
Refactoring and cleanups:
- Locally enable W=1 warnings by default in i915 (Jani)
- Move HDCP GSC message code to a separate file (Suraj)
- GVT include cleanups (Jani)
- Move more display init under display/ (Jani)
- DPLL ID refactoring (Ville)
- Better abstraction of GT0 (Jani)
- Move VGA decode function to GMCH code (Uma)
- Use local64_try_cmpxchg() to optimize PMU event read (Uros Bizjak)
- Clean up FBC checks (Ville)
- Constify and unify state checker calling conventions (Ville)
- Add display step name helper (Chaitanya)
Documentation:
- Update CCS and GSC CS documentation (Rodrigo)
- Fix a number of documentation typos (Randy Dunlap)
Fixes:
- VLV DSI fixes and quirks (Hans)
- Fix crtc state memory leaks (Suraj)
- Increase LSPCON mode settle timeout (Niko Tsirakis)
- Stop clobbering old crtc state during state check (Ville)
- Fix VLV color state readout (Ville)
- Fix cx0 PHY pipe reset to allow S0iX (Khaled)
- Ensure DP MST pbn_div is up-to-date after sink reconnect (Imre)
- Drop an unnecessary NULL check to fix static analyzer warning (Suraj)
- Use an explicit rather than implicit include for frontbuffer tracking (Jouni)
Merges:
- Backmerge drm-next to fix a conflict (Jani)
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/87r0m00xew.fsf@intel.com
|
|
git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for v6.7-rc1:
Contains the previous pull request drm-misc-next-2023-10-06 + following:
Cross-subsystem Changes:
- Rename fb_pgprot to pgprot_framebuffer and remove file argument/
- Update iosys-map documentation typos.
Core Changes:
- Assorted fixes to drm/panel.
- Add HPD state to drm_connector_oob_hotplug_event(), and implement
oob hotplug events in bridge connector.
- Replace drm_framebuffer_plane_width/height with calls to
drm_format_info_plane_width/height.
Driver Changes:
- Clock and debug fixes for bridge/samsung-dsim.
- More btree -> maple tree conversions.
- Assorted bugfixes in rockchip, panel-tpo-tpg110,
- Add LTK050H3148W-CTA6 panel support.
- Assorted small fixes in host1x, tegra, simpledrm.
- Suspend fixes for host1x.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/3812345e-b086-4d72-8504-f58d84e8feab@linux.intel.com
|
|
Use drm_color_lut_extract() to avoid open-coding the bits reduction
calculations for each color channel and use a struct drm_color_lut
to temporarily store the information instead of an array of u32.
Also, slightly improve the precision of the HW LUT calculation in the
LUT DIFF case by performing the subtractions on the 16-bits values and
doing the 10 bits conversion later.
Reviewed-by: Jason-JH.Lin <jason-jh.lin@mediatek.com>
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://patchwork.kernel.org/project/dri-devel/patch/20231012095736.100784-5-angelogioacchino.delregno@collabora.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
|
|
Newer SoCs support a bigger Gamma LUT table: wire up a callback
to retrieve the correct LUT size for each different Gamma IP.
Co-developed-by: Jason-JH.Lin <jason-jh.lin@mediatek.com>
Signed-off-by: Jason-JH.Lin <jason-jh.lin@mediatek.com>
[Angelo: Rewritten commit message/description + porting]
Reviewed-by: Jason-JH.Lin <jason-jh.lin@mediatek.com>
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://patchwork.kernel.org/project/dri-devel/patch/20231012095736.100784-4-angelogioacchino.delregno@collabora.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
|
|
Invert the check for state->gamma_lut and move it at the beginning
of the function to reduce indentation: this prepares the code for
keeping readability on later additions.
This commit brings no functional changes.
Reviewed-by: Jason-JH.Lin <jason-jh.lin@mediatek.com>
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://patchwork.kernel.org/project/dri-devel/patch/20231012095736.100784-3-angelogioacchino.delregno@collabora.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
|
|
Adjust the parameters in mtk_drm_gamma_set_common()
- add (struct device *dev) to get lut_diff from gamma's driver data
- remove (bool lut_diff) and use false as default value in the function
Signed-off-by: Jason-JH.Lin <jason-jh.lin@mediatek.com>
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://patchwork.kernel.org/project/dri-devel/patch/20231012095736.100784-2-angelogioacchino.delregno@collabora.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
|
|
|
|
From: Aaron Conole <aconole@redhat.com>
To: netdev@vger.kernel.org
Cc: dev@openvswitch.org, linux-kselftest@vger.kernel.org,
linux-kernel@vger.kernel.org, Pravin B Shelar <pshelar@ovn.org>,
"David S. Miller" <davem@davemloft.net>,
Eric Dumazet <edumazet@google.com>,
Jakub Kicinski <kuba@kernel.org>, Paolo Abeni <pabeni@redhat.com>,
Adrian Moreno <amorenoz@redhat.com>,
Eelco Chaudron <echaudro@redhat.com>,
shuah@kernel.org
Subject: [PATCH net v2 0/4] selftests: openvswitch: Minor fixes for some systems
Date: Wed, 11 Oct 2023 15:49:35 -0400 [thread overview]
Message-ID: <20231011194939.704565-1-aconole@redhat.com> (raw)
A number of corner cases were caught when trying to run the selftests on
older systems. Missed skip conditions, some error cases, and outdated
python setups would all report failures but the issue would actually be
related to some other condition rather than the selftest suite.
Address these individual cases.
====================
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ct_tuple v4 data structure decode / encode routines were using
the v6 IP address decode and relying on default encode. This could
cause exceptions during encode / decode depending on how a ct4
tuple would appear in a netlink message.
Caught during code review.
Fixes: e52b07aa1a54 ("selftests: openvswitch: add flow dump support")
Signed-off-by: Aaron Conole <aconole@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Kernels that don't have support for openvswitch drop reasons also
won't have the drop counter reasons, so we should skip the test
completely. It previously wasn't possible to build a test case
for this without polluting the datapath, so we introduce a mechanism
to clear all the flows from a datapath allowing us to test for
explicit drop actions, and then clear the flows to build the
original test case.
Fixes: 4242029164d6 ("selftests: openvswitch: add explicit drop testcase")
Signed-off-by: Aaron Conole <aconole@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In case of fatal signal, or early abort at least cleanup the current
test case.
Fixes: 25f16c873fb1 ("selftests: add openvswitch selftest suite")
Signed-off-by: Aaron Conole <aconole@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Paolo Abeni reports that on some systems the pyroute2 version isn't
new enough to run the test suite. Ensure that we support a minimum
version of 0.6 for all cases (which does include the existing ones).
The 0.6.1 version was released in May of 2021, so should be
propagated to most installations at this point.
The alternative that Paolo proposed was to only skip when the
add-flow is being run. This would be okay for most cases, except
if a future test case is added that needs to do flow dump without
an associated add (just guessing). In that case, it could also be
broken and we would need additional skip logic anyway. Just draw
a line in the sand now.
Fixes: 25f16c873fb1 ("selftests: add openvswitch selftest suite")
Reported-by: Paolo Abeni <pabeni@redhat.com>
Closes: https://lore.kernel.org/lkml/8470c431e0930d2ea204a9363a60937289b7fdbe.camel@redhat.com/
Signed-off-by: Aaron Conole <aconole@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit 45e34c8af58f23db4474e2bfe79183efec09a18b, and the
two subsequent fixes to it:
3f874c9b2aae ("x86/smp: Don't send INIT to non-present and non-booted CPUs")
b1472a60a584 ("x86/smp: Don't send INIT to boot CPU")
because it seems to result in hung machines at shutdown. Particularly
some Dell machines, but Thomas says
"The rest seems to be Lenovo and Sony with Alderlake/Raptorlake CPUs -
at least that's what I could figure out from the various bug reports.
I don't know which CPUs the DELL machines have, so I can't say it's a
pattern.
I agree with the revert for now"
Ashok Raj chimes in:
"There was a report (probably this same one), and it turns out it was a
bug in the BIOS SMI handler.
The client BIOS's were waiting for the lowest APICID to be the SMI
rendevous master. If this is MeteorLake, the BSP wasn't the one with
the lowest APIC and it triped here.
The BIOS change is also being pushed to others for assimilation :)
Server BIOS's had this correctly for a while now"
and it does look likely to be some bad interaction between SMI and the
non-BSP cores having put into INIT (and thus unresponsive until reset).
Link: https://bbs.archlinux.org/viewtopic.php?pid=2124429
Link: https://www.reddit.com/r/openSUSE/comments/16qq99b/tumbleweed_shutdown_did_not_finish_completely/
Link: https://forum.artixlinux.org/index.php/topic,5997.0.html
Link: https://bugzilla.redhat.com/show_bug.cgi?id=2241279
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Syzbot reported two new paths to hit an internal WARNING using the
new virtio gso type VIRTIO_NET_HDR_GSO_UDP_L4.
RIP: 0010:skb_checksum_help+0x4a2/0x600 net/core/dev.c:3260
skb len=64521 gso_size=344
and
RIP: 0010:skb_warn_bad_offload+0x118/0x240 net/core/dev.c:3262
Older virtio types have historically had loose restrictions, leading
to many entirely impractical fuzzer generated packets causing
problems deep in the kernel stack. Ideally, we would have had strict
validation for all types from the start.
New virtio types can have tighter validation. Limit UDP GSO packets
inserted via virtio to the same limits imposed by the UDP_SEGMENT
socket interface:
1. must use checksum offload
2. checksum offload matches UDP header
3. no more segments than UDP_MAX_SEGMENTS
4. UDP GSO does not take modifier flags, notably SKB_GSO_TCP_ECN
Fixes: 860b7f27b8f7 ("linux/virtio_net.h: Support USO offload in vnet header.")
Reported-by: syzbot+01cdbc31e9c0ae9b33ac@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/netdev/0000000000005039270605eb0b7f@google.com/
Reported-by: syzbot+c99d835ff081ca30f986@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/netdev/0000000000005426680605eb0b9f@google.com/
Signed-off-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 295525e29a5b ("virtio_net: merge dma operations when filling
mergeable buffers") unmaps the buffer with DMA_ATTR_SKIP_CPU_SYNC when
the dma->ref is zero. We do that with DMA_ATTR_SKIP_CPU_SYNC, because we
do not want to do the sync for the entire page_frag. But that misses the
sync for the current area.
This patch does cpu sync regardless of whether the ref is zero or not.
Fixes: 295525e29a5b ("virtio_net: merge dma operations when filling mergeable buffers")
Reported-by: Michael Roth <michael.roth@amd.com>
Closes: http://lore.kernel.org/all/20230926130451.axgodaa6tvwqs3ut@amd.com
Signed-off-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Commit f6fca3917b4d "btrfs: store chunk size in space-info struct"
broke data chunk allocations on non-zoned multi-device filesystems when
using default chunk_size. Commit 5da431b71d4b "btrfs: fix the max chunk
size and stripe length calculation" partially fixed that, and this patch
completes the fix for that case.
After commit f6fca3917b4d and 5da431b71d4b, the sequence of events for
a data chunk allocation on a non-zoned filesystem is:
1. btrfs_create_chunk calls init_alloc_chunk_ctl, which copies
space_info->chunk_size (default 10 GiB) to ctl->max_stripe_len
unmodified. Before f6fca3917b4d, ctl->max_stripe_len value was
1 GiB for non-zoned data chunks and not configurable.
2. btrfs_create_chunk calls gather_device_info which consumes
and produces more fields of chunk_ctl.
3. gather_device_info multiplies ctl->max_stripe_len by
ctl->dev_stripes (which is 1 in all cases except dup)
and calls find_free_dev_extent with that number as num_bytes.
4. find_free_dev_extent locates the first dev_extent hole on
a device which is at least as large as num_bytes. With default
max_chunk_size from f6fca3917b4d, it finds the first hole which is
longer than 10 GiB, or the largest hole if that hole is shorter
than 10 GiB. This is different from the pre-f6fca3917b4d
behavior, where num_bytes is 1 GiB, and find_free_dev_extent
may choose a different hole.
5. gather_device_info repeats step 4 with all devices to find
the first or largest dev_extent hole that can be allocated on
each device.
6. gather_device_info sorts the device list by the hole size
on each device, using total unallocated space on each device to
break ties, then returns to btrfs_create_chunk with the list.
7. btrfs_create_chunk calls decide_stripe_size_regular.
8. decide_stripe_size_regular finds the largest stripe_len that
fits across the first nr_devs device dev_extent holes that were
found by gather_device_info (and satisfies other constraints
on stripe_len that are not relevant here).
9. decide_stripe_size_regular caps the length of the stripe it
computed at 1 GiB. This cap appeared in 5da431b71d4b to correct
one of the other regressions introduced in f6fca3917b4d.
10. btrfs_create_chunk creates a new chunk with the above
computed size and number of devices.
At step 4, gather_device_info() has found a location where stripe up to
10 GiB in length could be allocated on several devices, and selected
which devices should have a dev_extent allocated on them, but at step
9, only 1 GiB of the space that was found on each device can be used.
This mismatch causes new suboptimal chunk allocation cases that did not
occur in pre-f6fca3917b4d kernels.
Consider a filesystem using raid1 profile with 3 devices. After some
balances, device 1 has 10x 1 GiB unallocated space, while devices 2
and 3 have 1x 10 GiB unallocated space, i.e. the same total amount of
space, but distributed across different numbers of dev_extent holes.
For visualization, let's ignore all the chunks that were allocated before
this point, and focus on the remaining holes:
Device 1: [_] [_] [_] [_] [_] [_] [_] [_] [_] [_] (10x 1 GiB unallocated)
Device 2: [__________] (10 GiB contig unallocated)
Device 3: [__________] (10 GiB contig unallocated)
Before f6fca3917b4d, the allocator would fill these optimally by
allocating chunks with dev_extents on devices 1 and 2 ([12]), 1 and 3
([13]), or 2 and 3 ([23]):
[after 0 chunk allocations]
Device 1: [_] [_] [_] [_] [_] [_] [_] [_] [_] [_] (10 GiB)
Device 2: [__________] (10 GiB)
Device 3: [__________] (10 GiB)
[after 1 chunk allocation]
Device 1: [12] [_] [_] [_] [_] [_] [_] [_] [_] [_]
Device 2: [12] [_________] (9 GiB)
Device 3: [__________] (10 GiB)
[after 2 chunk allocations]
Device 1: [12] [13] [_] [_] [_] [_] [_] [_] [_] [_] (8 GiB)
Device 2: [12] [_________] (9 GiB)
Device 3: [13] [_________] (9 GiB)
[after 3 chunk allocations]
Device 1: [12] [13] [12] [_] [_] [_] [_] [_] [_] [_] (7 GiB)
Device 2: [12] [12] [________] (8 GiB)
Device 3: [13] [_________] (9 GiB)
[...]
[after 12 chunk allocations]
Device 1: [12] [13] [12] [13] [12] [13] [12] [13] [_] [_] (2 GiB)
Device 2: [12] [12] [23] [23] [12] [12] [23] [23] [__] (2 GiB)
Device 3: [13] [13] [23] [23] [13] [23] [13] [23] [__] (2 GiB)
[after 13 chunk allocations]
Device 1: [12] [13] [12] [13] [12] [13] [12] [13] [12] [_] (1 GiB)
Device 2: [12] [12] [23] [23] [12] [12] [23] [23] [12] [_] (1 GiB)
Device 3: [13] [13] [23] [23] [13] [23] [13] [23] [__] (2 GiB)
[after 14 chunk allocations]
Device 1: [12] [13] [12] [13] [12] [13] [12] [13] [12] [13] (full)
Device 2: [12] [12] [23] [23] [12] [12] [23] [23] [12] [_] (1 GiB)
Device 3: [13] [13] [23] [23] [13] [23] [13] [23] [13] [_] (1 GiB)
[after 15 chunk allocations]
Device 1: [12] [13] [12] [13] [12] [13] [12] [13] [12] [13] (full)
Device 2: [12] [12] [23] [23] [12] [12] [23] [23] [12] [23] (full)
Device 3: [13] [13] [23] [23] [13] [23] [13] [23] [13] [23] (full)
This allocates all of the space with no waste. The sorting function used
by gather_device_info considers free space holes above 1 GiB in length
to be equal to 1 GiB, so once find_free_dev_extent locates a sufficiently
long hole on each device, all the holes appear equal in the sort, and the
comparison falls back to sorting devices by total free space. This keeps
usable space on each device equal so they can all be filled completely.
After f6fca3917b4d, the allocator prefers the devices with larger holes
over the devices with more free space, so it makes bad allocation choices:
[after 1 chunk allocation]
Device 1: [_] [_] [_] [_] [_] [_] [_] [_] [_] [_] (10 GiB)
Device 2: [23] [_________] (9 GiB)
Device 3: [23] [_________] (9 GiB)
[after 2 chunk allocations]
Device 1: [_] [_] [_] [_] [_] [_] [_] [_] [_] [_] (10 GiB)
Device 2: [23] [23] [________] (8 GiB)
Device 3: [23] [23] [________] (8 GiB)
[after 3 chunk allocations]
Device 1: [_] [_] [_] [_] [_] [_] [_] [_] [_] [_] (10 GiB)
Device 2: [23] [23] [23] [_______] (7 GiB)
Device 3: [23] [23] [23] [_______] (7 GiB)
[...]
[after 9 chunk allocations]
Device 1: [_] [_] [_] [_] [_] [_] [_] [_] [_] [_] (10 GiB)
Device 2: [23] [23] [23] [23] [23] [23] [23] [23] [23] [_] (1 GiB)
Device 3: [23] [23] [23] [23] [23] [23] [23] [23] [23] [_] (1 GiB)
[after 10 chunk allocations]
Device 1: [12] [_] [_] [_] [_] [_] [_] [_] [_] [_] (9 GiB)
Device 2: [23] [23] [23] [23] [23] [23] [23] [23] [12] (full)
Device 3: [23] [23] [23] [23] [23] [23] [23] [23] [_] (1 GiB)
[after 11 chunk allocations]
Device 1: [12] [13] [_] [_] [_] [_] [_] [_] [_] [_] (8 GiB)
Device 2: [23] [23] [23] [23] [23] [23] [23] [23] [12] (full)
Device 3: [23] [23] [23] [23] [23] [23] [23] [23] [13] (full)
No further allocations are possible, with 8 GiB wasted (4 GiB of data
space). The sort in gather_device_info now considers free space in
holes longer than 1 GiB to be distinct, so it will prefer devices 2 and
3 over device 1 until all but 1 GiB is allocated on devices 2 and 3.
At that point, with only 1 GiB unallocated on every device, the largest
hole length on each device is equal at 1 GiB, so the sort finally moves
to ordering the devices with the most free space, but by this time it
is too late to make use of the free space on device 1.
Note that it's possible to contrive a case where the pre-f6fca3917b4d
allocator fails the same way, but these cases generally have extensive
dev_extent fragmentation as a precondition (e.g. many holes of 768M
in length on one device, and few holes 1 GiB in length on the others).
With the regression in f6fca3917b4d, bad chunk allocation can occur even
under optimal conditions, when all dev_extent holes are exact multiples
of stripe_len in length, as in the example above.
Also note that post-f6fca3917b4d kernels do treat dev_extent holes
larger than 10 GiB as equal, so the bad behavior won't show up on a
freshly formatted filesystem; however, as the filesystem ages and fills
up, and holes ranging from 1 GiB to 10 GiB in size appear, the problem
can show up as a failure to balance after adding or removing devices,
or an unexpected shortfall in available space due to unequal allocation.
To fix the regression and make data chunk allocation work
again, set ctl->max_stripe_len back to the original SZ_1G, or
space_info->chunk_size if that's smaller (the latter can happen if the
user set space_info->chunk_size to less than 1 GiB via sysfs, or it's
a 32 MiB system chunk with a hardcoded chunk_size and stripe_len).
While researching the background of the earlier commits, I found that an
identical fix was already proposed at:
https://lore.kernel.org/linux-btrfs/de83ac46-a4a3-88d3-85ce-255b7abc5249@gmx.com/
The previous review missed one detail: ctl->max_stripe_len is used
before decide_stripe_size_regular() is called, when it is too late for
the changes in that function to have any effect. ctl->max_stripe_len is
not used directly by decide_stripe_size_regular(), but the parameter
does heavily influence the per-device free space data presented to
the function.
Fixes: f6fca3917b4d ("btrfs: store chunk size in space-info struct")
CC: stable@vger.kernel.org # 6.1+
Link: https://lore.kernel.org/linux-btrfs/20231007051421.19657-1-ce3g8jdj@umail.furryterror.org/
Reviewed-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: Zygo Blaxell <ce3g8jdj@umail.furryterror.org>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / Thunderbolt fixes from Greg KH:
"Here are some USB and Thunderbolt driver fixes for 6.6-rc6 to resolve
a number of small reported issues. Included in here are:
- thunderbolt driver fixes
- xhci driver fixes
- cdns3 driver fixes
- musb driver fixes
- a number of typec driver fixes
- a few other small driver fixes
All of these have been in linux-next with no reported issues"
* tag 'usb-6.6-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (22 commits)
usb: typec: ucsi: Use GET_CAPABILITY attributes data to set power supply scope
usb: typec: ucsi: Fix missing link removal
usb: typec: altmodes/displayport: Signal hpd low when exiting mode
xhci: Preserve RsvdP bits in ERSTBA register correctly
xhci: Clear EHB bit only at end of interrupt handler
xhci: track port suspend state correctly in unsuccessful resume cases
usb: xhci: xhci-ring: Use sysdev for mapping bounce buffer
usb: typec: ucsi: Clear EVENT_PENDING bit if ucsi_send_command fails
usb: misc: onboard_hub: add support for Microchip USB2412 USB 2.0 hub
usb: gadget: udc-xilinx: replace memcpy with memcpy_toio
usb: cdns3: Modify the return value of cdns_set_active () to void when CONFIG_PM_SLEEP is disabled
usb: dwc3: Soft reset phy on probe for host
usb: hub: Guard against accesses to uninitialized BOS descriptors
usb: typec: qcom: Update the logic of regulator enable and disable
usb: gadget: ncm: Handle decoding of multiple NTB's in unwrap call
usb: musb: Get the musb_qh poniter after musb_giveback
usb: musb: Modify the "HWVers" register address
usb: cdnsp: Fixes issue with dequeuing not queued requests
thunderbolt: Restart XDomain discovery handshake after failure
thunderbolt: Correct TMU mode initialization from hardware
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver fixes from Greg KH:
"Here are some small tty/serial driver fixes for 6.6-rc6 that resolve
some reported issues. Included in here are:
- serial core pm runtime fix for issue reported by many
- 8250_omap driver fix
- rs485 spinlock fix for reported problem
- ams-delta bugfix for previous tty api changes in -rc1 that missed
this driver that never seems to get built in any test systems
All of these have been in linux-next for over a week with no reported
problems"
* tag 'tty-6.6-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
ASoC: ti: ams-delta: Fix cx81801_receive() argument types
serial: core: Fix checks for tx runtime PM state
serial: 8250_omap: Fix errors with no_console_suspend
serial: Reduce spinlocked portion of uart_rs485_config()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here is a small set of char/misc and other smaller driver subsystem
fixes for 6.6-rc6. Included in here are:
- lots of iio driver fixes
- binder memory leak fix
- mcb driver fixes
- counter driver fixes
- firmware loader documentation fix
- documentation update for embargoed hardware issues
All of these have been in linux-next for over a week with no reported
issues"
* tag 'char-misc-6.6-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (22 commits)
iio: pressure: ms5611: ms5611_prom_is_valid false negative bug
dt-bindings: iio: adc: adi,ad7292: Fix additionalProperties on channel nodes
iio: adc: ad7192: Correct reference voltage
iio: light: vcnl4000: Don't power on/off chip in config
iio: addac: Kconfig: update ad74413r selections
iio: pressure: dps310: Adjust Timeout Settings
iio: imu: bno055: Fix missing Kconfig dependencies
iio: adc: imx8qxp: Fix address for command buffer registers
iio: cros_ec: fix an use-after-free in cros_ec_sensors_push_data()
iio: irsd200: fix -Warray-bounds bug in irsd200_trigger_handler
dt-bindings: iio: rohm,bu27010: add missing vdd-supply to example
binder: fix memory leaks of spam and pending work
firmware_loader: Update contact emails for ABI docs
Documentation: embargoed-hardware-issues.rst: Clarify prenotifaction
mcb: remove is_added flag from mcb_device struct
coresight: tmc-etr: Disable warnings for allocation failures
coresight: Fix run time warnings while reusing ETR buffer
iio: admv1013: add mixer_vgate corner cases
iio: pressure: bmp280: Fix NULL pointer exception
iio: dac: ad3552r: Correct device IDs
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/overlayfs/vfs
Pull overlayfs fixes from Amir Goldstein:
- Various fixes for regressions due to conversion to new mount
api in v6.5
- Disable a new mount option syntax (append lowerdir) that was
added in v6.5 because we plan to add a different lowerdir
append syntax in v6.7
* tag 'ovl-fixes-6.6-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/overlayfs/vfs:
ovl: temporarily disable appending lowedirs
ovl: fix regression in showing lowerdir mount option
ovl: fix regression in parsing of mount options with escaped comma
fs: factor out vfs_parse_monolithic_sep() helper
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
- Fix softlockup/crash when using hcall tracing
- Fix pte_access_permitted() for PAGE_NONE on 8xx
- Fix inverted pte_young() test in __ptep_test_and_clear_young()
on 64-bit BookE
- Fix unhandled math emulation exception on 85xx
- Fix kernel crash on syscall return on 476
Thanks to Athira Rajeev, Christophe Leroy, Eddie James, and Naveen N
Rao.
* tag 'powerpc-6.6-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/47x: Fix 47x syscall return crash
powerpc/85xx: Fix math emulation exception
powerpc/64e: Fix wrong test in __ptep_test_and_clear_young()
powerpc/8xx: Fix pte_access_permitted() for PAGE_NONE
powerpc/pseries: Remove unused r0 in the hcall tracing code
powerpc/pseries: Fix STK_PARAM access in the hcall tracing code
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull CPU hotplug fix from Ingo Molnar:
"Fix a Longsoon build warning by harmonizing the
arch_[un]register_cpu() prototypes between architectures"
* tag 'smp-urgent-2023-10-15' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
cpu-hotplug: Provide prototypes for arch CPU registration
|
