| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
This patch fixes the following DTC warning (requires W=1):
Node /soc/local_intc simple-bus unit address format error, expected "40000000"
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
Jon attempted to fix the amount of RAM on the BCM958625HR in commit
c53beb47f621 ("ARM: dts: NSP: Correct RAM amount for BCM958625HR board")
but it seems like we tripped over some poorly documented schematics.
The top-level page of the schematics says the board has 2GB, but when
you end-up scrolling to page 6, you see two chips of 4GBit (512MB) but
what the bootloader really initializes only 512MB, any attempt to use
more than that results in data aborts. Fix this again back to 512MB.
Fixes: c53beb47f621 ("ARM: dts: NSP: Correct RAM amount for BCM958625HR board")
Acked-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
It seems that the proper value to return in this particular case is the
one contained into variable new_index instead of ret.
Addresses-Coverity-ID: 1465148 ("Copy-paste error")
Fixes: e46c7287b1c2 ("nbd: add a basic netlink interface")
Reviewed-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security
Pull seccomp fix from James Morris:
"This disables the seccomp samples when cross compiling.
We've seen too many build issues here, so it's best to just disable
it, especially since they're just the samples"
* 'fixes-v4.16-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
samples/seccomp: do not compile when cross compiled
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/kees/linux into fixes-v4.16-rc4
- do not build samples when cross compiling (Michal Hocko)
From Kees: "This disables the seccomp samples when cross compiling. We're seen too many build issues here, so
it's best to just disable it, especially since they're just the samples."
|
|
Kernel crashed when run fio in a RAID5 backend bcache device, the call
trace is bellow:
[ 440.012034] kernel BUG at block/blk-ioc.c:146!
[ 440.012696] invalid opcode: 0000 [#1] SMP NOPTI
[ 440.026537] CPU: 2 PID: 2205 Comm: md127_raid5 Not tainted 4.15.0 #8
[ 440.027441] Hardware name: HP ProLiant MicroServer Gen8, BIOS J06 07/16
/2015
[ 440.028615] RIP: 0010:put_io_context+0x8b/0x90
[ 440.029246] RSP: 0018:ffffa8c882b43af8 EFLAGS: 00010246
[ 440.029990] RAX: 0000000000000000 RBX: ffffa8c88294fca0 RCX: 0000000000
0f4240
[ 440.031006] RDX: 0000000000000004 RSI: 0000000000000286 RDI: ffffa8c882
94fca0
[ 440.032030] RBP: ffffa8c882b43b10 R08: 0000000000000003 R09: ffff949cb8
0c1700
[ 440.033206] R10: 0000000000000104 R11: 000000000000b71c R12: 00000000000
01000
[ 440.034222] R13: 0000000000000000 R14: ffff949cad84db70 R15: ffff949cb11
bd1e0
[ 440.035239] FS: 0000000000000000(0000) GS:ffff949cba280000(0000) knlGS:
0000000000000000
[ 440.060190] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 440.084967] CR2: 00007ff0493ef000 CR3: 00000002f1e0a002 CR4: 00000000001
606e0
[ 440.110498] Call Trace:
[ 440.135443] bio_disassociate_task+0x1b/0x60
[ 440.160355] bio_free+0x1b/0x60
[ 440.184666] bio_put+0x23/0x30
[ 440.208272] search_free+0x23/0x40 [bcache]
[ 440.231448] cached_dev_write_complete+0x31/0x70 [bcache]
[ 440.254468] closure_put+0xb6/0xd0 [bcache]
[ 440.277087] request_endio+0x30/0x40 [bcache]
[ 440.298703] bio_endio+0xa1/0x120
[ 440.319644] handle_stripe+0x418/0x2270 [raid456]
[ 440.340614] ? load_balance+0x17b/0x9c0
[ 440.360506] handle_active_stripes.isra.58+0x387/0x5a0 [raid456]
[ 440.380675] ? __release_stripe+0x15/0x20 [raid456]
[ 440.400132] raid5d+0x3ed/0x5d0 [raid456]
[ 440.419193] ? schedule+0x36/0x80
[ 440.437932] ? schedule_timeout+0x1d2/0x2f0
[ 440.456136] md_thread+0x122/0x150
[ 440.473687] ? wait_woken+0x80/0x80
[ 440.491411] kthread+0x102/0x140
[ 440.508636] ? find_pers+0x70/0x70
[ 440.524927] ? kthread_associate_blkcg+0xa0/0xa0
[ 440.541791] ret_from_fork+0x35/0x40
[ 440.558020] Code: c2 48 00 5b 41 5c 41 5d 5d c3 48 89 c6 4c 89 e7 e8 bb c2
48 00 48 8b 3d bc 36 4b 01 48 89 de e8 7c f7 e0 ff 5b 41 5c 41 5d 5d c3 <0f> 0b
0f 1f 00 0f 1f 44 00 00 55 48 8d 47 b8 48 89 e5 41 57 41
[ 440.610020] RIP: put_io_context+0x8b/0x90 RSP: ffffa8c882b43af8
[ 440.628575] ---[ end trace a1fd79d85643a73e ]--
All the crash issue happened when a bypass IO coming, in such scenario
s->iop.bio is pointed to the s->orig_bio. In search_free(), it finishes the
s->orig_bio by calling bio_complete(), and after that, s->iop.bio became
invalid, then kernel would crash when calling bio_put(). Maybe its upper
layer's faulty, since bio should not be freed before we calling bio_put(),
but we'd better calling bio_put() first before calling bio_complete() to
notify upper layer ending this bio.
This patch moves bio_complete() under bio_put() to avoid kernel crash.
[mlyle: fixed commit subject for character limits]
Reported-by: Matthias Ferdinand <bcache@mfedv.net>
Tested-by: Matthias Ferdinand <bcache@mfedv.net>
Signed-off-by: Tang Junhui <tang.junhui@zte.com.cn>
Reviewed-by: Michael Lyle <mlyle@lyle.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Commit 2831231d4c3f ("bcache: reduce cache_set devices iteration by
devices_max_used") adds c->devices_max_used to reduce iteration of
c->uuids elements, this value is updated in bcache_device_attach().
But for flash only volume, when calling flash_devs_run(), the function
bcache_device_attach() is not called yet and c->devices_max_used is not
updated. The unexpected result is, the flash only volume won't be run
by flash_devs_run().
This patch fixes the issue by iterate all c->uuids elements in
flash_devs_run(). c->devices_max_used will be updated properly when
bcache_device_attach() gets called.
[mlyle: commit subject edited for character limit]
Fixes: 2831231d4c3f ("bcache: reduce cache_set devices iteration by devices_max_used")
Reported-by: Tang Junhui <tang.junhui@zte.com.cn>
Signed-off-by: Coly Li <colyli@suse.de>
Reviewed-by: Michael Lyle <mlyle@lyle.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security
Pull tpm fixes from James Morris:
"Bugfixes for TPM, from Jeremy Boone, via Jarkko Sakkinen"
* 'fixes-v4.16-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
tpm: fix potential buffer overruns caused by bit glitches on the bus
tpm: st33zp24: fix potential buffer overruns caused by bit glitches on the bus
tpm_i2c_infineon: fix potential buffer overruns caused by bit glitches on the bus
tpm_i2c_nuvoton: fix potential buffer overruns caused by bit glitches on the bus
tpm_tis: fix potential buffer overruns caused by bit glitches on the bus
|
|
We can never idle the l3_main hwmod so mark the omap_l3_noc node
with ti,no-idle.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
We can never idle the emif hwmod from within the HLOS so mark the emif
node with ti,no-idle.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
We can never idle the emif hwmod from within the HLOS so mark the emif
node with ti,no-idle.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add soc node for am4372 with pm-sram phandle to both pm-sram-code and
pm-sram-data regions.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add a phandle to point to both the pm-sram-code and pm-sram-data nodes
so that the pm code can locate the sram regions needed to copy low level
PM code.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Now that we will use ti-emif-sram driver for am4372 PM, update the
emif DT node with the required sram property.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Now that we will use ti-emif-sram driver for am335x PM, update the
emif DT node with the required sram property.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add a 'pm_sram_code' reserved region to the ocmcram node to be exposed
by the mmio-sram driver as a pool but also mark it protect-exec so that
it can run code copied to it using sram_exec_copy.
Add another 'pm_sram_data' reserved region to the ocmcram node to act as
the data space for any code running from the 'pm_sram_code' region that
is exposed as a regular pool.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add a 'pm_sram_code' reserved region to the ocmcram node to be exposed
by the mmio-sram driver as a pool but also mark it protect-exec so that
it can run code copied to it using sram_exec_copy.
Add another 'pm_sram_data' reserved region to the ocmcram node to act as
the data space for any code running from the 'pm_sram_code' region that
is exposed as a regular pool.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Use the new bindings of the reworked Marvell NAND controller driver.
Also adapt the nand controller node organization to distinguish which
property is relevant for the controller, and which one is NAND chip
specific. Expose the partitions as a subnode of the NAND chip.
Remove the 'marvell,nand-enable-arbiter' property, not needed anymore as
the driver activates the arbiter by default for all boards (either
needed or harmless).
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
Use the new bindings of the reworked Marvell NAND controller driver.
Also adapt the nand controller node organization to distinguish which
property is relevant for the controller, and which one is NAND chip
specific. Expose the partitions as a subnode of the NAND chip.
Remove the 'marvell,nand-enable-arbiter' property, not needed anymore as
the driver activates the arbiter by default for all boards (either
needed or harmless).
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
This extra clock is needed to access the registers of the AHCI SATA
controller used on the Armada 7K/8K SoCs.
The ahci drivers was already designed to support up to 5 clocks so there
is only need to update the device tree to use it. It was not noticed
until now because of wrong assumption in the clock drivers, but as this
IP really needs 2 clocks, we had to declare both of them.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
commit a307a1e6bc0d "cpufreq: s3c: use cpufreq_generic_init()"
accidentally broke cpufreq on s3c2410 and s3c2412.
These two platforms don't have a CPU frequency table and used to skip
calling cpufreq_table_validate_and_show() for them. But with the
above commit, we started calling it unconditionally and that will
eventually fail as the frequency table pointer is NULL.
Fix this by calling cpufreq_table_validate_and_show() conditionally
again.
Fixes: a307a1e6bc0d "cpufreq: s3c: use cpufreq_generic_init()"
Cc: 3.13+ <stable@vger.kernel.org> # v3.13+
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
This patch enables RTC on stm32h743i-eval.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
This patch adds support for RTC on STM32H743 SoC.
It also adds dt-bindings/interrupt-controller/irq.h include and uses it to
configure RTC alarm interrupt.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
This patch enables USB HS on stm32h743i-eval in OTG (DRD) mode.
The USB connector used will determine the role of USB OTG controller.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
This patch adds support for USB OTG HS and FS on STM32H743 SoC:
-USB OTG HS controller is the same than the one used on STM32F7 SoCs.
-USB OTG FS controller is the same than the one used on STM32F4 SoCs.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
This patch enables RTC on stm32f769-disco.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
This patch enables USB HS on stm32f749-disco in OTG (DRD) mode.
The USB connector used will determine the role of USB OTG controller.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
Configure USB OTG HS in OTG (DRD) mode on STM32746G_eval.
The USB connector used will determine the role of USB OTG controller.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
USB OTG HS on STM32F746 can also be used as Peripheral (gadget), so
this patch adds DWC2 gadget mode fifo sizes bindings.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
As the block layer, since the conversion to blkmq, claims the host using a
context, a following nested call to mmc_claim_host(), which isn't using a
context, may hang.
Calling mmc_interrupt_hpi() and mmc_read_bkops_status() via the mmc block
layer, may suffer from this problem, as these functions are calling
mmc_claim|release_host().
Let's fix the problem by removing the calls to mmc_claim|release_host()
from the above mentioned functions and instead make the callers responsible
of claiming/releasing the host. As a matter of fact, the existing callers
already deals with it.
Fixes: 81196976ed94 ("mmc: block: Add blk-mq support")
Reported-by: Dmitry Osipenko <digetx@gmail.com>
Suggested-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
|
|
cat /sys/kernel/debug/mmc0/regs will hang up the system since
it's in runtime suspended state, so the genpd and biu_clk is
off. This patch fixes this problem by calling pm_runtime_get_sync
to wake it up before reading the registers.
Fixes: e9ed8835e990 ("mmc: dw_mmc: add runtime PM callback")
Cc: <stable@vger.kernel.org>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Add num_caps field for dw_mci_drv_data to validate the controller
id from DT alias and non-DT ways.
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Fixes: 800d78bfccb3 ("mmc: dw_mmc: add support for implementation specific callbacks")
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Factor out dw_mci_init_slot_caps to consolidate parsing
all differents types of capabilities from host contrllers.
No functional change intended.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Fixes: 800d78bfccb3 ("mmc: dw_mmc: add support for implementation specific callbacks")
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The hs_timing_cfg[] array is indexed using a value derived from the
"mshcN" alias in DT, which may lead to an out-of-bounds access.
Fix this by adding a range check.
Fixes: 361c7fe9b02eee7e ("mmc: dw_mmc-k3: add sd support for hi3660")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Add node for user push button.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
Add node for user push button.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
Add nodes for the two user leds.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
Add nodes for the four user leds.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
The HSE oscillator frequency was wrongly set to 125MHz instead of 25MHz.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
This patch adds STM32MP157 SoC bindings.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
This patch adds SDIO related DT nodes for stm32429i-eval board.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
This patch adds SDIO-related DT nodes required by stm32f469 board
There is a hardware issue on these boards, it misses a pullup on
the GPIO line used as card detect to allow correct SD card
detection. To allow correct card detection "broken-cd" property
is used.
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
wake_klogd is a local variable in console_unlock(). The information
is lost when the console_lock owner using the busy wait added by
the commit dbdda842fe96f8932 ("printk: Add console owner and waiter
logic to load balance console writes"). The following race is
possible:
CPU0 CPU1
console_unlock()
for (;;)
/* calling console for last message */
printk()
log_store()
log_next_seq++;
/* see new message */
if (seen_seq != log_next_seq) {
wake_klogd = true;
seen_seq = log_next_seq;
}
console_lock_spinning_enable();
if (console_trylock_spinning())
/* spinning */
if (console_lock_spinning_disable_and_check()) {
printk_safe_exit_irqrestore(flags);
return;
console_unlock()
if (seen_seq != log_next_seq) {
/* already seen */
/* nothing to do */
Result: Nobody would wakeup klogd.
One solution would be to make a global variable from wake_klogd.
But then we would need to manipulate it under a lock or so.
This patch wakes klogd also when console_lock is passed to the
spinning waiter. It looks like the right way to go. Also userspace
should have a chance to see and store any "flood" of messages.
Note that the very late klogd wake up was a historic solution.
It made sense on single CPU systems or when sys_syslog() operations
were synchronized using the big kernel lock like in v2.1.113.
But it is questionable these days.
Fixes: dbdda842fe96f8932 ("printk: Add console owner and waiter logic to load balance console writes")
Link: http://lkml.kernel.org/r/20180226155734.dzwg3aovqnwtvkoy@pathway.suse.cz
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: linux-kernel@vger.kernel.org
Cc: Tejun Heo <tj@kernel.org>
Suggested-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Reviewed-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Signed-off-by: Petr Mladek <pmladek@suse.com>
|
|
This patch adds the pin configuration for SDIO controller on
stm32f4.
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
stm32f429 embeds ARM_PL180 sdi IP, adds SDIO controller
node to allow MMC support.
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
stm32f746 embeds ARM_PL180 sdio IP, adds SDIO controller
nodes to allow MMC support.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
Tuning can leave the IP in an active state (Buffer Read Enable bit set)
which prevents the entry to low power states (i.e. S0i3). Data reset will
clear it.
Generally tuning is followed by a data transfer which will anyway sort out
the state, so it is rare that S0i3 is actually prevented.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
of_get_named_gpiod_flags() used directly in of_find_gpio() or indirectly
through of_find_spi_gpio() or of_find_regulator_gpio() can return
-EPROBE_DEFER. This gets overwritten by the subsequent of_find_*_gpio()
calls.
This patch fixes this by trying of_find_spi_gpio() or
of_find_regulator_gpio() only if deferred probing was not requested by
the previous of_get_named_gpiod_flags() call.
Fixes: 6a537d48461d ("gpio: of: Support regulator nonstandard GPIO properties")
Fixes: c85823390215 ("gpio: of: Support SPI nonstandard GPIO properties")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
[Augmented to fit with Maxime's patch]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Commits c85823390215 ("gpio: of: Support SPI nonstandard GPIO properties")
and 6a537d48461d ("gpio: of: Support regulator nonstandard GPIO
properties") have introduced a regression in the way error codes from
of_get_named_gpiod_flags are handled.
Previously, those errors codes were returned immediately, but the two
commits mentioned above are now overwriting the error pointer, meaning that
whatever value has been returned will be dropped in favor of whatever the
two new functions will return.
This might not be a big deal except for EPROBE_DEFER, on which GPIOlib
customers will depend on, and that will now be returned as an hard error
which means that they will not probe anymore, instead of gently deferring
their probe.
Since EPROBE_DEFER basically means that we have found a valid property but
there was no GPIO controller registered to handle it, fix this issues by
returning it as soon as we encounter it.
Fixes: c85823390215 ("gpio: of: Support SPI nonstandard GPIO properties")
Fixes: 6a537d48461d ("gpio: of: Support regulator nonstandard GPIO properties")
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
[Fold in fix to the fix]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This exposes to mesa that it can use the fixed ioctl for querying
later cap sets, cap set 1 is forever frozen in time.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20180221015003.22884-1-airlied@gmail.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
|
