summaryrefslogtreecommitdiff
AgeCommit message (Collapse)AuthorFilesLines
2015-10-20ARM: dts: am335x-igep0033: Use IOPAD pinmux macroJavier Martinez Canillas1-20/+20
Use the AM33xx pinmux IOPAD macro to define the physical address instead of the offset from the padconf address. It makes the DTS easier to read since matches the addresses listed in the Technical Reference Manual. Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2015-10-20ARM: dts: omap3-igep0020: Use IOPAD pinmux macroJavier Martinez Canillas1-29/+29
Use the OMAP3 pinmux IOPAD macro to define the physical address instead of the offset from the padconf address. It makes the DTS easier to read since matches the addresses listed in the Technical Reference Manual. Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2015-10-20ARM: dts: am437x-gp-evm: Add wakeup interrupt source for pixcir_i2c_tsVignesh R1-0/+9
On am437x-gp-evm, pixcir_i2c_ts can wakeup the system from low power state via pinctrl and IO daisy chain using generic wakeirq framework. With commit 3fffd1283927 ("i2c: allow specifying separate wakeup interrupt in device tree") i2c core allows optional wakeirq to be specified via device tree. Add wakeup irq entry to enable pixcir_i2c_ts to wake the system from low power state. Signed-off-by: Vignesh R <vigneshr@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2015-10-20ARM: dts: Update Javier Martinez Canillas's emailJavier Martinez Canillas7-7/+7
I see that people are still sending emails to my old address (that no longer exists) since is the one mentioned in the IGEP DTS. Replace it with my current email address to avoid this. Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2015-10-20ARM: dts: dra72-evm: remove cpsw gpio hogging and add mode-gpiosMugunthan V N1-6/+1
With the current implementation of GPIO hogging and with gpio-pcf857x is built as module, ethernet doesn't work on boot and doesn't throw any error/warning to user. Ethernet becomes operational when inserting gpio-pcf857x module, even this time there is no error/warning logs to user that ethernet is operational. When using with NFS rootfs and gpio-pcf857x as module, board doesn't boot as it doesn't get any ip address and doesn't throw any error/warning. To over come this, now cpsw driver tries to get mode-gpios. When gpio-pcf857x is built as module it will throw error, so that user can decide either to built in gpio-pcf857x to continue with nfs boot or choose alternate rootfs filesystem like sd/ramdisk. When using mmc/ramdisk as root fs, cpsw will probe defer and re-probes again when gpio-pcf857x module is inserted and ethernet becomes operational. Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2015-10-20ARM: tegra: Use consistent indentation for SATA nodeThierry Reding1-12/+6
The indentation for properties in the SATA device tree node on Tegra124 deviates from the rest of the device tree file. Restore consistency and get rid of a couple of gratuitous blank lines while at it. Signed-off-by: Thierry Reding <treding@nvidia.com>
2015-10-19ARM: at91/dt: sama5d2: add missing devicesLudovic Desroches1-2/+150
Big update of the sama5d2.dtsi file since many patches have reached te mainline: - add generated clocks - enable crypto devices - add flexcom devices - add tdes device - add sdmmc devices Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2015-10-19ARM: at91/dt: sama5d4: add the macb1 nodeGregory CLEMENT1-0/+30
The second macb is present on all the sama5d4 SoCs. Let's add a node reflecting it in the device tree. Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2015-10-19ARM: at91/dt: add pullup on mmc2 data signalsSylvain Rochet1-3/+3
MMC data lines may be left floating if nothing is currently driving the data lines, which is the case when mmc is in idle state, thus consuming a useless extra amount of power. Add pullup on mmc2 data signals in the same way it was previously done for mmc0 and mmc1. Signed-off-by: Sylvain Rochet <sylvain.rochet@finsecur.com> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2015-10-19ARM: at91/dt: sama5d2_xplained: add regulator nodesWenyou Yang1-0/+57
Add regulator nodes of PMIC ACT8945A chip on the board. Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2015-10-19ARM: at91/dt: fix "disabled" property on at91rm9200Michael Opdenacker1-3/+3
Fix instances of "disable" instead of "disabled" in the at91rm9200 dtsi. Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2015-10-19ARM: at91/dt: use syscon for PMCAlexandre Belloni11-11/+11
The PMC is not only used to drive the clocks but also has some registers related to other functions. One of those is for example the USB gadget bias. Using a syscon allows to properly separate those functions. Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2015-10-19ARM: dts: ls1021a: Add quirk for Erratum A009116Rajesh Bhagat1-0/+1
Add "snps,quirk-frame-length-adjustment" property to USB3 node for erratum A009116. This property provides value of GFLADJ_30MHZ for post silicon frame length adjustment. Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com> Signed-off-by: Rajesh Bhagat <rajesh.bhagat@freescale.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2015-10-19ARM: imx6sx-sdb: Fix typo in regulator enable GPIO propertyLaurent Pinchart1-1/+1
The property name should be "gpio", not "gpios". Fix it. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2015-10-19ARM: dts: imx6: phyFLEX: fix typo in "pinctrl-names"Michael Opdenacker1-2/+2
Fix a typo, replacing "pinctrl-name" by "pinctrl-names" in the Phytec phyFLEX-i.MX6 Quad dtsi. Also fix a typo in the board name Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2015-10-19ARM: dts: imx6: change the core clock of spdifShengjiu Wang3-7/+23
The correct core clock of spdif is SPDIF_GCLK, which is added to clock tree. So the dts also need to be updated. Signed-off-by: Shengjiu Wang <shengjiu.wang@freescale.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2015-10-19ARM: dts: vf-colibri: enable NAND flash controllerStefan Agner1-0/+39
Enable NAND access by adding pinmux and NAND flash controller node to device tree. The NAND chips currently used on the Colibri VF61 requires 8-bit ECC per 512 byte page, hence specify 32-bit ECC strength per 2k page size. Reviewed-by: Brian Norris <computersforpeace@gmail.com> Signed-off-by: Stefan Agner <stefan@agner.ch> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2015-10-19ARM: dts: vf610twr: add NAND flash controller peripherialStefan Agner2-0/+58
This adds the NAND flash controller (NFC) peripherial. The driver supports the SLC NAND chips found on Freescale's Vybrid Tower System Module. The Micron NAND chip on the module needs 4-bit ECC per 512 byte page. Use 24-bit ECC per 2k page, which is supported by the driver. Signed-off-by: Bill Pringlemeir <bpringlemeir@nbsps.com> Reviewed-by: Brian Norris <computersforpeace@gmail.com> Signed-off-by: Stefan Agner <stefan@agner.ch> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2015-10-19ARM: dts: imx: add Boundary Devices Nitrogen6_Lite boardGary Bisson3-0/+680
Based on an i.MX6 Solo with 512MB DDR3. http://boundarydevices.com/product/nitrogen6_lite/ Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2015-10-19ARM: dts: imx: add Boundary Devices Nitrogen6_Max boardGary Bisson3-0/+927
Based on i.MX6 Quad with 4GB of DDR3. http://boundarydevices.com/product/nitrogen6max/ Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2015-10-19ARM: dts: imx6dl-nitrogen6x: change manufacturer to Boundary DevicesGary Bisson1-2/+2
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2015-10-19ARM: dts: imx6q-nitrogen6x: change manufacturer to Boundary DevicesGary Bisson1-2/+2
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2015-10-19of: Add Boundary Devices Inc. vendor prefixGary Bisson1-0/+1
This patch adds the vendor prefix for Boundary Devices Inc. which is a supplier of ARM-based single board computers and System-on-Modules for the general embedded market. Website: http://boundarydevices.com/ Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2015-10-19ARM: dts: imx6qdl-sabrelite: relicense under GPLv2/X11Gary Bisson3-15/+105
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2015-10-19ARM: dts: imx6qdl-nitrogen6x: relicense under GPLv2/X11Gary Bisson3-15/+105
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2015-10-19ARM: dts: imx6qdl-nitrogen6x: add wifi wl1271 supportGary Bisson1-0/+55
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2015-10-19ARM: dts: imx6dql-nitrogen6x: add touchscreen supportGary Bisson1-0/+16
This patch adds the different touchscreens that can be connected using the displays available for this board. http://boundarydevices.com/product-category/displays/ Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2015-10-19ARM: dts: imx6qdl-sabrelite: add Okaya LCD panelGary Bisson1-1/+75
This patch adds support for the 7" LCD display available for Sabrelite: http://boundarydevices.com/product/7-800x480-display/ Also add label to backlight_lcd and connect it to the panel. Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2015-10-19ARM: dts: imx6qdl-nitrogen6x: add Okaya LCD panelGary Bisson1-1/+75
This patch adds support for the 7" LCD display available for Nitrogen6x: http://boundarydevices.com/product/7-800x480-display/ Also add label to backlight_lcd and connect it to the panel. Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2015-10-19ARM: dts: vf500-colibri: Add device tree node for touchscreen supportSanchayan Maity2-0/+52
Add device tree node for touchscreen support on Colibri VF50. The touchscreen functionality on VF50 uses the ADC channels of Vybrid and some GPIOs. Also add pinctrl nodes for proper pinmux. Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2015-10-19ARM: dts: i.MX35: fix cpu compatible valueVladimir Zapolskiy1-1/+1
The change corrects cpu compatible property to a defined one, see Documentation/devicetree/bindings/arm/cpus.txt Signed-off-by: Vladimir Zapolskiy <vz@mleia.com> Cc: Sascha Hauer <kernel@pengutronix.de> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2015-10-19ARM: dts: i.MX31: fix cpu compatible valueVladimir Zapolskiy1-1/+1
The change corrects cpu compatible property to a defined one, see Documentation/devicetree/bindings/arm/cpus.txt Signed-off-by: Vladimir Zapolskiy <vz@mleia.com> Cc: Sascha Hauer <kernel@pengutronix.de> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2015-10-19ARM: dts: imx: imx7d add iomuxc lpsr device nodeAdrian Alonso1-0/+6
Add device tree node to support iomuxc-lpsr controller, fsl,input-sel phandle allows to get input select register base address which is shared from main iomuxc controller. Signed-off-by: Adrian Alonso <aalonso@freescale.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2015-10-19ARM: dts: imx7d-sdb: add fec1 and fec2 supportFugang Duan1-1/+75
Enable fec1 and fec2 for i.MX7d-sdb board. Signed-off-by: Fugang Duan <B38611@freescale.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2015-10-19ARM: dts: imx7d-pinfunc: add gpio1 pad iomux settingsAdrian Alonso1-3/+119
- Add imx7 SoC GPIO1 pad iomuxc settings <mux_reg conf_reg input_reg mux_mode input_val> - Fix UART input select daisy chain setting values Signed-off-by: Adrian Alonso <aalonso@freescale.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2015-10-19ARM: dts: Add node for ina220 on LS1021ATWRYuan Yao1-0/+13
The INA220 monitors both shunt drop and supply voltage. Signed-off-by: Yuan Yao <yao.yuan@freescale.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2015-10-19ARM: ls1021a: Add dma-coherent property for eTSEC nodesAlison Wang1-0/+3
This patch adds dma-coherent property for eTSEC nodes, so coherent DMA operations are supported. Signed-off-by: Alison Wang <alison.wang@freescale.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2015-10-19ARM: dts: imx7d-sdb: Add USB supportFabio Estevam1-0/+11
Add support for USBOTG1 and USBOTG2. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2015-10-19ARM: dts: imx7d: Add USB supportFabio Estevam1-0/+71
Add USB OTG and Host support. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2015-10-19ARM: dts: imx7d: add fec1 and fec2 support for i.MX7d socFugang Duan1-0/+36
Add fec1 and fec2 nodes for i.MX7d soc. Signed-off-by: Fugang Duan <B38611@freescale.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2015-10-19ARM: dts: ls1021a: add crypto nodeHoria Geantă1-0/+40
Signed-off-by: Horia Geantă <horia.geanta@freescale.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2015-10-19ARM: dts: imx6ul-14x14-evk.dts: add tsc supportHaibo Chen1-0/+18
Add touch screen surpport for i.MX6UL-EVK board. Signed-off-by: Haibo Chen <haibo.chen@freescale.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2015-10-19ARM: dts: imx6ul.dtsi: add TSC supportHaibo Chen1-0/+11
Add imx6ul touchscreen controller support. TSC module need ADC2 module to measure the touchscreen coordinate value. This patch put TSC and ADC2 together, make ADC2 module only be used for TSC, can't be used as a normal ADC. Signed-off-by: Haibo Chen <haibo.chen@freescale.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2015-10-19ARM: dts: imx7d: Add PWM supportFabio Estevam1-0/+52
Add the PWM1-4 nodes. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2015-10-19ARM: dts: imx6sl: Complete the dcp nodeFabio Estevam1-1/+4
The DCP block present on MX6SL is compatible with the one on MX28, so add the compatible string and also complete the interrupt entries. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2015-10-19ARM: dts: imx: add "jedec,spi-nor" flash compatible bindingRafał Miłecki19-21/+21
Starting with commit 8947e396a829 ("Documentation: dt: mtd: replace "nor-jedec" binding with "jedec, spi-nor"") we have "jedec,spi-nor" binding indicating support for JEDEC identification. Use it for all flashes that are supposed to support READ ID op according to the datasheets. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2015-10-19ARM: mxs: enable ocotp for i.MX23 and i.MX28Stefan Wahren2-4/+8
This patch enables On Chip OTP support for i.MX23 and i.MX28 SoCs, but keeps the old compatible string. Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com> Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2015-10-19ARM: dts: imx7d-sdb: add eMMC5.0 supportHaibo Chen1-0/+13
imx7d-sdb board has a eMMC5.0 on usdhc3. This eMMC support HS400. This patch add usdhc3 support for HS400 Signed-off-by: Haibo Chen <haibo.chen@freescale.com> Acked-by: Dong Aisheng <aisheng.dong@freescale.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2015-10-19ARM: dts: imx6ul: add pm_power_off supportAnson Huang2-0/+12
i.MX6UL can be powered off by programming SNVS. When long press ON/OFF button(5 seconds), PMIC_ON_REQ pin will be set to low and external PMIC will be powered off. And system can be powered on by long press ON/OFF button again. Signed-off-by: Anson Huang <b20788@freescale.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2015-10-19ARM: dts: imx6ul: add mmdc support for i.mx6ulAnson Huang1-0/+5
Add MMDC support for i.MX6UL. Signed-off-by: Anson Huang <b20788@freescale.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
generated by cgit v1.2.3 (git 2.39.0) at 2025-09-30 21:34:53 +0300