| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Describe OSPI and QSPI flash partition information through device tree,
this helps to remove passing partition information through the mtdparts
commandline parameter which requires maintaining the partition information
in a string format. J721E SoM has a MT35 64 MiB OSPI flash and MT25 64 MiB
QSPI flash both with sector size of 128 KiB thus the size of the smallest
partition is chosen as 128KiB, the partition names and offsets are chosen
according to the corresponding name and offsets in bootloader.
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Link: https://lore.kernel.org/r/20230513141712.27346-2-vaishnav.a@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
J784S4 has S28HS512T OSPI flash connected to OSPI0 and MT25QU512A QSPI
flash connected to OSPI1, enable support for the same. Also describe
the partition information according to the offsets in the bootloader.
Co-developed-by: Vaishnav Achath <vaishnav.a@ti.com>
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Signed-off-by: Apurva Nandan <a-nandan@ti.com>
Link: https://lore.kernel.org/r/20230504080305.38986-3-a-nandan@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
TI K3 J784S4 has the Cadence OSPI controllers OSPI0 and OSPI1 on FSS
bus for interfacing with OSPI flashes. Add the nodes to allow using
SPI flashes.
Signed-off-by: Apurva Nandan <a-nandan@ti.com>
Link: https://lore.kernel.org/r/20230504080305.38986-2-a-nandan@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
With commit 9f6ffd0da650 ("dt-bindings: leds: Convert PCA9532 to dtschema"),
we can now add the LED controller without introducing new dtbs_check warnings.
Add missing I2C LED controller.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Link: https://lore.kernel.org/r/20230505131012.2027309-1-w.egorov@phytec.de
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
J721E common processor board has an onboard mux for selecting whether
the OSPI signals are externally routed to OSPI flash or Hyperflash. The
mux state signal input is tied to WKUP_GPIO0_8 and is used by bootloader
for enabling the corresponding node accordingly. Add pinmux for the same.
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Link: https://lore.kernel.org/r/20230513123313.11462-5-vaishnav.a@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
J7200 common processor board has an onboard mux for selecting whether
the OSPI signals are externally routed to OSPI flash or Hyperflash. The
mux state signal input is tied to WKUP_GPIO0_6 and is used by bootloader
for enabling the corresponding node accordingly. Add pinmux for the same.
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Link: https://lore.kernel.org/r/20230513123313.11462-4-vaishnav.a@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
J721E SoM has a HyperFlash and HyperRam connected to HyperBus memory
controller, add corresponding node, pinmux and partitions for the same.
HyperBus is muxed with OSPI and only one controller can be active at a
time, therefore keep HyperBus node disabled. Bootloader will detect the
external mux state through a wkup gpio and enable the node as required.
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Link: https://lore.kernel.org/r/20230513123313.11462-3-vaishnav.a@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
J721E has a Flash SubSystem that has one OSPI and one HyperBus with
muxed datapath and another independent OSPI. Add DT nodes for HyperBus
controller and keep it disabled and model the data path selection mux as a
reg-mux.
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Link: https://lore.kernel.org/r/20230513123313.11462-2-vaishnav.a@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
MDIO nodes defined in the top-level J721e SoC dtsi files are incomplete
and will not be functional unless they are extended with a pinmux.
As the attached PHY is only known about at the board integration level,
these nodes should only be enabled when provided with this information.
Disable the MDIO nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20230515172137.474626-5-afd@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Mailbox nodes defined in the top-level AM64x SoC dtsi files are incomplete
and may not be functional unless they are extended with a chosen interrupt
and connection to a remote processor.
As the remote processors depend on memory nodes which are only known at
the board integration level, these nodes should only be enabled when
provided with the above information.
Disable the Mailbox nodes in the dtsi files and only enable the ones that
are actually used on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20230515172137.474626-4-afd@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
PCIe nodes defined in the top-level J721e SoC dtsi files are incomplete
and will not be functional unless they are extended with a SerDes PHY.
And usually only one of the two modes can be used at a time as they
share a SerDes link.
As the PHY and mode is only known at the board integration level, these
nodes should only be enabled when provided with this information.
Disable the PCIe nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20230515172137.474626-3-afd@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
These nodes are example nodes for the PCIe controller in "endpoint" mode.
By default the controller is in "root complex" mode and there is already a
DT node for the same.
Examples should go in the bindings or other documentation.
Remove this node.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20230515172137.474626-2-afd@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Mailbox nodes are now disabled by default. The BeagleBoard AI64 DT
addition went in at around the same time and must have missed that
change so the mailboxes are not re-enabled. Do that here.
Fixes: fae14a1cb8dd ("arm64: dts: ti: Add k3-j721e-beagleboneai64")
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20230515172137.474626-1-afd@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
eMMC tuning was incomplete earlier, so support for high speed modes was
kept disabled. Remove no-1-8-v property to enable support for high
speed modes for eMMC in J784S4 SoC.
Signed-off-by: Bhavya Kapoor <b-kapoor@ti.com>
Link: https://lore.kernel.org/r/20230502090814.144791-1-b-kapoor@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
J784S4 has two instances of 8 channel ADCs in MCU domain. Add pinmux
information for both ADC nodes.
Signed-off-by: Bhavya Kapoor <b-kapoor@ti.com>
Link: https://lore.kernel.org/r/20230502081117.21431-3-b-kapoor@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
J784S4 has two instances of 8 channel ADCs in MCU domain. Add support
for both ADC nodes.
Signed-off-by: Bhavya Kapoor <b-kapoor@ti.com>
Link: https://lore.kernel.org/r/20230502081117.21431-2-b-kapoor@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
The OLDI-LCD1EVM add on board has Rocktech RK101II01D-CT panel[1] with
integrated touch screen. The integrated touch screen is Goodix GT928.
This panel connects with AM65 GP-EVM[2].
Add DT nodes for these and connect the endpoint nodes with DSS.
[1]: Panel link
https://www.digimax.it/en/tft-lcd/20881-RK101II01D-CT
[2]: AM654 LCD EVM:
https://www.ti.com/tool/TMDSLCD1EVM
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Nikhil Devshatwar <nikhil.nd@ti.com>
[abhatia1@ti.com: Make cosmetic and 6.4 kernel DTSO syntax changes]
Signed-off-by: Aradhya Bhatia <a-bhatia1@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20230509102354.10116-2-a-bhatia1@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Update the delay values for various speed modes supported, based on
the revised august 2021 J721E Datasheet.
[1] - Table 7-77. MMC0 DLL Delay Mapping for All Timing Modes and
Table 7-86. MMC1/2 DLL Delay Mapping for All Timing Modes, in
https://www.ti.com/lit/ds/symlink/tda4vm.pdf,
(SPRSP36J – FEBRUARY 2019 – REVISED AUGUST 2021)
Signed-off-by: Bhavya Kapoor <b-kapoor@ti.com>
Link: https://lore.kernel.org/r/20230424093827.1378602-1-b-kapoor@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Include documentation of the AMC package pin name as well to keep it
consistent with the rest of the pinctrl documentation.
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20230418213740.153519-5-nm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Add board EEPROM support to device tree
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20230418213740.153519-4-nm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
wkup_uart and main_uart1 on this platform is used by tifs and DM
firmwares. Describe them for completeness including the pinmux.
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20230418213740.153519-3-nm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Drop an extra EoL
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20230418213740.153519-2-nm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Looks like a couple of http:// links crept in. Use https instead.
While at it, drop unicode encoded character.
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20230417225450.1182047-1-nm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
VTM stands for Voltage Thermal Management. Add the thermal zones.
Six sensors mapping to six thermal zones. Main0, Main1, Main2, Main3,
WKUP1 & WKUP2 domains respectively.
Signed-off-by: Keerthy <j-keerthy@ti.com>
[bb@ti.com: rebased on v6.3-rc1]
Signed-off-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20230405215328.3755561-8-bb@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
VTM stands for Voltage Thermal Management. Add the thermal zones.
Three sensors mapping to 3 thermal zones. MCU, MPU & Main domains
respectively.
Signed-off-by: Keerthy <j-keerthy@ti.com>
[bb@ti.com: rebased on v6.3-rc1]
Signed-off-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20230405215328.3755561-7-bb@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
VTM stands for Voltage Thermal Management. Add the thermal zones.
Five sensors mapping ton 5 thermal zones. WKUP, MPU, C7x, GPU & R5F
respectively.
Signed-off-by: Keerthy <j-keerthy@ti.com>
[bb@ti.com: rebased on v6.3-rc1]
Signed-off-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20230405215328.3755561-6-bb@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
VTM stands for Voltage Thermal Management. Add the thermal zones.
Seven sensors mapping to seven thermal zones. Main0, Main1, Main2, Main3,
Main4, WKUP1 & WKUP2 domains respectively.
Signed-off-by: Keerthy <j-keerthy@ti.com>
[bb@ti.com: rebased on v6.3-rc1]
Signed-off-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20230405215328.3755561-5-bb@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
The am62ax supports a single Voltage and Thermal Management (VTM) device
located in the wakeup domain with three associated temperature monitors
located in various hot spots of the die.
Signed-off-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20230405215328.3755561-4-bb@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
The am62x supports a single Voltage and Thermal Management (VTM) module
located in the wakeup domain with two associated temperature monitors
located in hot spots of the die.
Signed-off-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20230405215328.3755561-3-bb@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
The am64x supports a single VTM module which is located in the main
domain with two associated temperature monitors located at different hot
spots on the die.
Tested-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20230405215328.3755561-2-bb@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
x1 lane PCIe slot in the common processor board is enabled and connected to
J721S2 SOM. Add PCIe DT node in common processor board to reflect the
same.
Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Matt Ranostay <mranostay@ti.com>
Signed-off-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20230331090028.8373-9-r-gunasekaran@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Add PCIe1 RC device tree node for the single PCIe instance present on
the J721S2.
Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Matt Ranostay <mranostay@ti.com>
Signed-off-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20230331090028.8373-8-r-gunasekaran@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
J721S2 has an OSPI NOR flash on its SOM connected the OSPI0 instance and a
QSPI NOR flash on the common processor board connected to the OSPI1
instance. Add support for the same
Reviewed-by: Vaishnav Achath <vaishnav.a@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Matt Ranostay <mranostay@ti.com>
Signed-off-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20230331090028.8373-7-r-gunasekaran@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
The board uses lane 1 of SERDES for USB. Set the mux
accordingly.
The USB controller and EVM supports super-speed for USB0
on the Type-C port. However, the SERDES has a limitation
that up to 2 protocols can be used at a time. The SERDES is
wired for PCIe, eDP and USB super-speed. It has been
chosen to use PCIe and eDP as default. So restrict
USB0 to high-speed mode.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Matt Ranostay <mranostay@ti.com>
Signed-off-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20230331090028.8373-6-r-gunasekaran@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Configure first lane to PCIe, the second lane to USB and the last two lanes
to eDP. Also, add sub-nodes to SERDES0 DT node to represent SERDES0 is
connected to PCIe.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Matt Ranostay <mranostay@ti.com>
Signed-off-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20230331090028.8373-5-r-gunasekaran@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Add support for two instance of OSPI in J721S2 SoC.
Reviewed-by: Vaishnav Achath <vaishnav.a@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Matt Ranostay <mranostay@ti.com>
Signed-off-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20230331090028.8373-4-r-gunasekaran@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Add dt node for the single instance of WIZ (SERDES wrapper) and
SERDES module shared by PCIe, eDP and USB.
Signed-off-by: Matt Ranostay <mranostay@ti.com>
Signed-off-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20230331090028.8373-3-r-gunasekaran@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Add support for single instance of USB 3.0 controller in J721S2 SoC.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Matt Ranostay <mranostay@ti.com>
Signed-off-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20230331090028.8373-2-r-gunasekaran@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
USB0 is a Type-C port with dual data role and power sink.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20230330084954.49763-3-rogerq@kernel.org
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Reserve memory for remote processors. Two memory regions are reserved
for each remote processor. The first 1Mb region is used for virtio
Vring buffers for IPC and the second region is used for holding
resource table, trace buffer and as external memory to the remote
processor. The mailboxes are also assigned for each remote processor.
Signed-off-by: Hari Nagalla <hnagalla@ti.com>
Link: https://lore.kernel.org/r/20230502231527.25879-4-hnagalla@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
The J784S4 SoCs have four TMS320C71x DSP subsystems in the MAIN voltage
domain. The functionality of these DSP subsystems is similar to the C71x
DSP subsystems on earlier k3 device J721S2. Each subsystem has a 48 KB of
L1D configurable SRAM/Cache and 512 KB of L2 SRAM/Cache. This subsystem
has a CMMU but is not currently used. The inter-processor communication
between the main A72 cores and the C71x DSPs is achieved through shared
memory and mailboxes. Add the DT nodes for these DSP processor sub-systems.
Signed-off-by: Hari Nagalla <hnagalla@ti.com>
Link: https://lore.kernel.org/r/20230502231527.25879-3-hnagalla@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
The J784S4 SoCs have 4 dual-core Arm Cortex-R5F processor (R5FSS)
subsystems/clusters. One R5F cluster (MCU_R5FSS0) is present within
the MCU domain, and the remaining three clusters are present in the
MAIN domain (MAIN_R5FSS0, MAIN_R5FSS1 & MAIN_R5FSS2). The functionality
of the R5FSS is same as the R5FSS functionality on earlier K3 platform
device J721S2. Each of the R5FSS can be configured at boot time to be
either run in a LockStep mode or in an Asymmetric Multi Processing (AMP)
fashion in Split-mode. These subsystems have 64 KB each Tightly-Coupled
Memory (TCM) internal memories for each core split between two banks -
ATCM and BTCM (further interleaved into two banks). There are some IP
integration differences from standard Arm R5 clusters such as the absence
of an ACP port, presence of an additional TI-specific Region Address
Translater (RAT) module for translating 32-bit CPU addresses into
larger system bus addresses etc.
Add the DT nodes for the R5F cluster/subsystems, the two R5F cores are
each added as child nodes to the corresponding cluster node. The clusters
are configured to run in LockStep mode by default, with the ATCMs enabled
to allow the R5 cores to execute code from DDR with boot-strapping code
from ATCM. The inter-processor communication between the main A72 cores
and these processors is achieved through shared memory and Mailboxes.
The following firmware names are used by default for these cores, and
can be overridden in a board dts file if needed:
MAIN R5FSS0 Core0: j784s4-main-r5f0_0-fw (both in LockStep and Split modes)
MAIN R5FSS0 Core1: j784s4-main-r5f0_1-fw (needed only in Split mode)
MAIN R5FSS1 Core0: j784s4-main-r5f1_0-fw (both in LockStep and Split modes)
MAIN R5FSS1 Core1: j784s4-main-r5f1_1-fw (needed only in Split mode)
MAIN R5FSS2 Core0: j784s4-main-r5f2_0-fw (both in LockStep and Split modes)
MAIN R5FSS2 Core1: j784s4-main-r5f2_1-fw (needed only in Split mode)
MCU R5FSS0 Core0: j784s4-mcu-r5f0_0-fw (needed only in Split mode)
MCU R5FSS0 Core1: j784s4-mcu-r5f0_1-fw (needed only in Split mode)
Signed-off-by: Hari Nagalla <hnagalla@ti.com>
Link: https://lore.kernel.org/r/20230502231527.25879-2-hnagalla@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
This patch enables wkup_i2c0 node in board dts file
along with pin mux and speed.
Also enables underneath eeprom CAV24C256WE.
J7200 Datasheet (Table 6-106, Section 6.4 Pin Multiplexing) :
https://www.ti.com/lit/ds/symlink/dra821u.pdf
J7200 User Guide (Section 4.3, Table 4-2) :
https://www.ti.com/lit/ug/spruiw7a/spruiw7a.pdf
Signed-off-by: Udit Kumar <u-kumar1@ti.com>
Link: https://lore.kernel.org/r/20230419040007.3022780-3-u-kumar1@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
wkup_pmx splits into multiple regions. Like
wkup_pmx0 -> 13 pins (WKUP_PADCONFIG 0 - 12)
wkup_pmx1 -> 2 pins (WKUP_PADCONFIG 14 - 15)
wkup_pmx2 -> 59 pins (WKUP_PADCONFIG 26 - 84)
wkup_pmx3 -> 8 pins (WKUP_PADCONFIG 93 - 100)
With this split, pin offset needs to be adjusted to
match with new pmx for all pins above wkup_pmx0.
Example a pin under wkup_pmx1 should start from 0 instead of
old offset(0x38 WKUP_PADCONFIG 14 offset)
J7200 Datasheet (Table 6-106, Section 6.4 Pin Multiplexing) :
https://www.ti.com/lit/ds/symlink/dra821u.pdf
Fixes: 9ae21ac445e9 ("arm64: dts: ti: k3-j7200: Fix wakeup pinmux range")
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Udit Kumar <u-kumar1@ti.com>
Link: https://lore.kernel.org/r/20230419040007.3022780-2-u-kumar1@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
wkup_uart and main_uart1 on this platform is used by tifs and DM
firmwares. Describe them for completeness including the pinmux.
Signed-off-by: Nishanth Menon <nm@ti.com>
[bb@ti.com: updated pinmux and commit subject]
Signed-off-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20230425221708.549675-1-bb@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Remove "syscon" nodes added for pcieX_ctrl and have the PCIe node
point to the parent with an offset argument. This change is as
discussed in [1].
[1] http://lore.kernel.org/r/CAL_JsqKiUcO76bo1GoepWM1TusJWoty_BRy2hFSgtEVMqtrvvQ@mail.gmail.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20230424144949.244135-2-nm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
As all level 2 and level 3 caches are unified, add required
cache-unified properties to fix warnings like:
k3-am6528-iot2050-basic-pg2.dtb: l3-cache0: 'cache-unified' is a required property
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20230421223143.115099-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
iot boards have always defined their own aliases and with the base-board
defining it's own aliases, there are no pending boards depending on
common aliases defined in SoC level.
aliases are meant to be defined appropriately based on the exposed
interfaces at a board level, drop the aliases defined at SoC level.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Kamlesh Gurudasani <kamlesh@ti.com>
Link: https://lore.kernel.org/r/20230419225913.663448-8-nm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Introduce aliases compatible with the base definition, but focussed on
the interfaces that have been exposed on the platform.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Kamlesh Gurudasani <kamlesh@ti.com>
Link: https://lore.kernel.org/r/20230419225913.663448-7-nm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Enable AT24CM01 on the base board using the corresponding compatible.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Kamlesh Gurudasani <kamlesh@ti.com>
Link: https://lore.kernel.org/r/20230419225913.663448-6-nm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
