| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Active scan support is based on the current passive scan support,
cheered up with beacon requests sent after every channel change.
Co-developed-by: David Girault <david.girault@qorvo.com>
Signed-off-by: David Girault <david.girault@qorvo.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Alexander Aring <aahringo@redhat.com>
Link: https://lore.kernel.org/r/20230310145346.1397068-3-miquel.raynal@bootlin.com
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
|
|
In case a passive scan could not discover any PAN, a device may decide
to perform an active scan to force coordinators to send a BEACON
"immediately". Allow users to request to perform an active scan.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Alexander Aring <aahringo@redhat.com>
Link: https://lore.kernel.org/r/20230310145346.1397068-2-miquel.raynal@bootlin.com
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
|
|
4 places in the act api code are using 'TCA_' definitions where they
should be using 'TCA_ACT_', which is confusing for the reader, although
functionally they are equivalent.
Cc: Hangbin Liu <haliu@redhat.com>
Reviewed-by: Jamal Hadi Salim <jhs@mojatatu.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Pedro Tammela <pctammela@mojatatu.com>
Acked-by: Hangbin Liu <haliu@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2023-03-21 (igb, igbvf, igc)
This series contains updates to igb, igbvf, and igc drivers.
Andrii changes igb driver to utilize diff_by_scaled_ppm() implementation
over an open-coded version.
Dawid adds pci_error_handlers for reset_prepare and reset_done for
igbvf.
Sasha removes unnecessary code in igc.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Petr Machata says:
====================
net: Allow changing IPv4 address protocol
IPv4 and IPv6 addresses can be assigned a protocol value that indicates the
provenance of the IP address. The attribute is modeled after ip route
protocols, and essentially allows the administrator or userspace stack to
tag addresses in some way that makes sense to the actor in question.
When IP address protocol field was added in commit 47f0bd503210 ("net: Add
new protocol attribute to IP addresses"), the semantics included the
ability to change the protocol for IPv6 addresses, but not for IPv4
addresses. It seems this was not deliberate, but rather by accident.
One particular use case is tagging the addresses differently depending on
whether the routing stack should advertise them or not. Without support for
protocol replacement, this can not be done.
In this patchset, extend IPv4 to allow changing the protocol defined at an
address (in patch #1). Then in patches #2 and #3 add selftest coverage for
ip address protocols.
Currently the kernel simply ignores the new value. Thus allowing the
replacement changes the observable behavior. However, since IPv6 already
behaves like this anyway, and since the feature as such is relatively new,
it seems like the change is safe to make.
An example session with the feature in action:
bash-5.2# ip address add dev d 192.0.2.1/28 proto 0xab
bash-5.2# ip address show dev d
4: d: <BROADCAST,NOARP> mtu 1500 qdisc noop state DOWN group default qlen 1000
link/ether 06:29:74:fd:1f:eb brd ff:ff:ff:ff:ff:ff
inet 192.0.2.1/28 scope global proto 0xab d
valid_lft forever preferred_lft forever
bash-5.2# ip address replace dev d 192.0.2.1/28 proto 0x11
bash-5.2# ip address show dev d
4: d: <BROADCAST,NOARP> mtu 1500 qdisc noop state DOWN group default qlen 1000
link/ether 06:29:74:fd:1f:eb brd ff:ff:ff:ff:ff:ff
inet 192.0.2.1/28 scope global proto 0x11 d
valid_lft forever preferred_lft forever
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add coverage of "ip address {add,replace} ... proto" support.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Extract the list of all tests into a variable, ALL_TESTS. Then assume the
environment variable TESTS holds the list of tests to actually run, falling
back to ALL_TESTS if TESTS is empty. This is the same interface that
forwarding selftests use to make the set of tests to run configurable.
In addition to this, allow setting the value explicitly through a command
line option "-t" along the lines of what fib_nexthops.sh does.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When IP address protocol field was added in commit 47f0bd503210 ("net: Add
new protocol attribute to IP addresses"), the semantics included the
ability to change the protocol for IPv6 addresses, but not for IPv4
addresses. It seems this was not deliberate, but rather by accident.
A userspace that wants to change the protocol of an address might drop and
recreate the address, but that disrupts routing and is just impractical.
So in this patch, when an IPv4 address is replaced (through RTM_NEWADDR
request with NLM_F_REPLACE flag), update the proto at the address to the
one given in the request, or zero if none is given. This matches the
behavior of IPv6. Previously, any new value given was simply ignored.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Alex Elder says:
====================
net: ipa: fully support IPA v5.0
At long last, add the IPA and GSI register definitions, and the
configuration data required to support IPA v5.0. This enables IPA
support for the Qualcomm SDX65 SoC.
The first version of this series had build errors due to a
non-existent source file being required. This version addresses
that by changing how required files are specified in the Makefile.
Note that the second patch has some warnings about lines starting
with spaces; those spaces align text with the open parenthesis on
the previous line.
====================
Link: https://lore.kernel.org/r/20230321182644.2143990-1-elder@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add the configuration data required for IPA v5.0, which is used in
the SDX65 SoC.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add the definitions of GSI register offsets and fields for IPA v5.0.
These are used for the SDX65 SoC. Increase the maximum channel and
event ring counts supported by the driver, so those implemented by
the SDX65 are supported.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add the definitions of IPA register offsets and fields for IPA v5.0.
These are used for the SDX65 SoC.
In the Makefile, split IPA_VERSIONS to use IPA_REG_VERSIONS and
IPA_DATA_VERSIONS instead, to allow IPA register definitions for a
new version to be added separate from the IPA data.
Rename GSI_IPA_VERSIONS to be GSI_REG_VERSIONS for consistency.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Russell King says:
====================
Quirk for OEM SFP-2.5G-T copper module
Frank Wunderlich reports that this copper module requires a quirk in
order to function - in that the module needs to use 2500base-X.
Moreover, negotiation must be disabled.
An example of this device would be:
https://www.optcore.net/product/sfp-2g-t-gen
====================
Link: https://lore.kernel.org/r/ZBniMlTDZJQ242DP@shell.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add a quirk for a copper SFP that identifies itself as "OEM"
"SFP-2.5G-T". This module's PHY is inaccessible, and can only run
at 2500base-X with the host without negotiation. Add a quirk to
enable the 2500base-X interface mode with 2500base-T support, and
disable autonegotiation.
Reported-by: Frank Wunderlich <frank-w@public-files.de>
Tested-by: Frank Wunderlich <frank-w@public-files.de>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Allow SFP quirks to override the Autoneg, Pause and Asym_Pause bits in
the support mask.
Some modules have an inaccessible PHY on which is only accessible via
2500base-X without Autonegotiation. We therefore want to be able to
clear the Autoneg bit. Rearrange sfp_parse_support() to allow a SFP
modes quirk to override this bit.
Tested-by: Frank Wunderlich <frank-w@public-files.de>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Eric Dumazet says:
====================
net: remove some skb_mac_header assumptions
Historically, we tried o maintain skb_mac_header available in most of
networking paths.
When reaching ndo_start_xmit() handlers, skb_mac_header() should always
be skb->data.
With recent additions of skb_mac_header_was_set() and
DEBUG_NET_WARN_ON_ONCE() in skb_mac_header(), we can attempt
to remove our reliance on skb_mac_header in TX paths.
When this effort completes we will remove skb_reset_mac_header()
from __dev_queue_xmit() and replace it by
skb_unset_mac_header() on DEBUG_NET builds.
====================
Link: https://lore.kernel.org/r/20230321164519.1286357-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
tcf_mirred_act() and tcf_mpls_act() can use skb_network_offset()
instead of relying on skb_mac_header().
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
We want to remove our use of skb_mac_header() in tx paths,
eg remove skb_reset_mac_header() from __dev_queue_xmit().
Idea is that ndo_start_xmit() can get the mac header
simply looking at skb->data.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
We want to remove our use of skb_mac_header() in tx paths,
eg remove skb_reset_mac_header() from __dev_queue_xmit().
Idea is that ndo_start_xmit() can get the mac header
simply looking at skb->data.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Russell King says:
====================
Remove phylink_state's an_enabled member
Now that all the fixes and correctness patches have been merged, it is
time to switch the two users that make use of .an_enabled to check the
Autoneg bit in the advertising mask, and finally remove the
.an_enabled member.
The first two patches remove the last uses of .an_enabled, which are
in DPAA2 and XPCS. The final patch removes the member.
====================
Link: https://lore.kernel.org/r/ZBnT6yW9UY1sAsiy@shell.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The Autoneg bit in the advertising bitmap and state->an_enabled are
always identical. state->an_enabled is now no longer used by any
drivers, so lets kill this duplication.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The Autoneg bit in the advertising bitmap and state->an_enabled are
always identical. Thus, we will be removing state->an_enabled.
Use the Autoneg bit in the advertising bitmap to indicate whether
autonegotiation should be used, rather than using the an_enabled
member which will be going away.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The Autoneg bit in the advertising bitmap and state->an_enabled are
always identical. Thus, we will be removing state->an_enabled.
Use the Autoneg bit in the advertising bitmap to indicate whether
autonegotiation should be used, rather than using the an_enabled
member which will be going away. This means we use the same condition
as phylink_mii_c22_pcs_config().
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When requesting a TX queue at a given index, warn on out-of-bounds
referencing if the index is greater than the allocated number of
queues.
Specifically, since this function is used heavily in the networking
stack use DEBUG_NET_WARN_ON_ONCE to avoid executing a new branch on
every packet.
Signed-off-by: Nick Child <nnac123@linux.ibm.com>
Link: https://lore.kernel.org/r/20230321150725.127229-2-nnac123@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When setting the XPS value of a TX queue, warn the user once if the
index of the queue is greater than the number of allocated TX queues.
Previously, this scenario went uncaught. In the best case, it resulted
in unnecessary allocations. In the worst case, it resulted in
out-of-bounds memory references through calls to `netdev_get_tx_queue(
dev, index)`. Therefore, it is important to inform the user but not
worth returning an error and risk downing the netdevice.
Signed-off-by: Nick Child <nnac123@linux.ibm.com>
Reviewed-by: Piotr Raczynski <piotr.raczynski@intel.com>
Link: https://lore.kernel.org/r/20230321150725.127229-1-nnac123@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Siddharth Vadapalli says:
====================
Add CPSWxG SGMII support for J7200 and J721E
This series adds support to configure the CPSW Ethernet Switch in SGMII
mode, using the am65-cpsw-nuss driver. SGMII mode is supported by the
CPSWxG instances on TI's J7200 and J721E SoCs. Thus, SGMII mode is added
in the list of extra_modes for the appropriate compatibles corresponding
to the aforementioned SoCs.
Additionally, the method of setting the supported interface via struct
"phylink_config" is simplified by converting the IF/ELSE statements to
SWITCH statements.
====================
Link: https://lore.kernel.org/r/20230321111958.2800005-1-s-vadapalli@ti.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
TI's J721E SoC supports SGMII mode with the CPSW9G instance of the CPSW
Ethernet Switch. Thus, enable it by adding SGMII mode to the extra_modes
member of the "j721e_cpswxg_pdata" SoC data.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
TI's J7200 SoC supports SGMII mode with the CPSW5G instance of the CPSW
Ethernet Switch. Thus, enable it by adding SGMII mode to the extra_modes
member of the "j7200_cpswxg_pdata" SoC data.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add support for configuring the CPSW Ethernet Switch in SGMII mode.
Depending on the SoC, allow selecting SGMII mode as a supported interface,
based on the compatible used.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Convert the existing IF/ELSE statement based approach of setting the
supported_interfaces member of struct "phylink_config", to SWITCH
statements. This will help scale to newer PHY-MODES as well as newer
compatibles.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
clang with W=1 reports
drivers/net/ethernet/cavium/liquidio/request_manager.c:43:19: error:
unused function 'IQ_INSTR_MODE_64B' [-Werror,-Wunused-function]
static inline int IQ_INSTR_MODE_64B(struct octeon_device *oct, int iq_no)
^
This function and its macro wrapper are not used, so remove them.
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230321184811.1827306-1-trix@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux
Leon Romanovsky says:
====================
Extend packet offload to fully support libreswan
The following patches are an outcome of Raed's work to add packet
offload support to libreswan [1].
The series includes:
* Priority support to IPsec policies
* Statistics per-SA (visible through "ip -s xfrm state ..." command)
* Support to IKE policy holes
* Fine tuning to acquire logic.
[1] https://github.com/libreswan/libreswan/pull/986
Link: https://lore.kernel.org/all/cover.1678714336.git.leon@kernel.org
* tag 'ipsec-libreswan-mlx5' of https://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux:
net/mlx5e: Update IPsec per SA packets/bytes count
net/mlx5e: Use one rule to count all IPsec Tx offloaded traffic
net/mlx5e: Support IPsec acquire default SA
net/mlx5e: Allow policies with reqid 0, to support IKE policy holes
xfrm: copy_to_user_state fetch offloaded SA packets/bytes statistics
xfrm: add new device offload acquire flag
net/mlx5e: Use chains for IPsec policy priority offload
net/mlx5: fs_core: Allow ignore_flow_level on TX dest
net/mlx5: fs_chains: Refactor to detach chains from tc usage
====================
Link: https://lore.kernel.org/r/20230320094722.1009304-1-leon@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Cleanup bindings dropping unneeded quotes. Once all these are fixed,
checking for this can be enabled in yamllint.
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> # for bindings/net/can
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Steen Hegelund <Steen.Hegelund@microchip.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp> # for bindings/net/toshiba,visconti-dwmac.yaml
Reviewed-by: Heiko Stuebner <heiko@sntech.de> #rockchip
Link: https://lore.kernel.org/r/20230320233758.2918972-1-robh@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Álvaro Fernández Rojas says:
====================
net: dsa: b53: configure 6318 and 63268 RGMII ports
BCM6318 and BCM63268 need special configuration for their RGMII ports, so we
need to be able to identify them as a special BCM63xx switch.
In the meantime, let's add some missing BCM63xx SoCs to B53 MMAP device table.
This should be applied after "net: dsa: b53: add support for BCM63xx RGMIIs":
https://patchwork.kernel.org/project/netdevbpf/patch/20230319220805.124024-1-noltari@gmail.com/
Álvaro Fernández Rojas (4):
dt-bindings: net: dsa: b53: add more 63xx SoCs
net: dsa: b53: mmap: add more 63xx SoCs
net: dsa: b53: mmap: allow passing a chip ID
net: dsa: b53: add BCM63268 RGMII configuration
.../devicetree/bindings/net/dsa/brcm,b53.yaml | 3 ++
drivers/net/dsa/b53/b53_common.c | 19 +++++++++++-
drivers/net/dsa/b53/b53_mmap.c | 29 +++++++++++++++----
drivers/net/dsa/b53/b53_priv.h | 9 +++++-
drivers/net/dsa/b53/b53_regs.h | 1 +
5 files changed, 53 insertions(+), 8 deletions(-)
====================
Link: https://lore.kernel.org/r/20230321173359.251778-1-noltari@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
BCM63268 requires special RGMII configuration to work.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
BCM6318 and BCM63268 SoCs require a special handling for their RGMIIs, so we
should be able to identify them as a special BCM63xx switch.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
BCM6318, BCM6362 and BCM63268 are SoCs with a B53 MMAP switch.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
BCM6318, BCM6362 and BCM63268 are SoCs with a B53 MMAP switch.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
phy_disconnect() calls phy_detach() which already clears 'phydev' if it
is attached to a struct net_device.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20230321131745.27688-1-wsa+renesas@sang-engineering.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Pavan Chebbi says:
====================
bnxt PTP optimizations
Patches to
1. Enforce software based freq adjustments only on shared PHC NIC
2. A prerequisite change to expand capability storage field to
accommodate more Firmware reported capabilities
====================
Link: https://lore.kernel.org/r/20230321144449.15289-1-pavan.chebbi@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently driver performs software based frequency adjustments
when RTC capability is not discovered or when in shared PHC mode.
But there may be some old firmware versions that still support
hardware freq adjustments without RTC capability being exposed.
In this situation driver will use non-realtime mode even on single
host NICs.
Hence enforce software frequency adjustments only when running in
shared PHC mode. Make suitable changes for cyclecounter for the
same.
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Acked-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Driver uses the flag BNXT_FLAG_MULTI_HOST to determine whether
to use non-realtime mode PHC when running on a multi host NIC.
However when ptp initializes on a NIC with shared PHC, we still
don't have this flag set yet because HWRM_FUNC_QCFG is issued
much later.
Move the ptp initialization code after we have issued func_qcfg.
The next patch will use the BNXT_FLAG_MULTI_HOST flag during PTP
initialization.
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Acked-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The current fw_cap field (u32) has run out of bits to save any
new capability.
Change the field to u64.
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Acked-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add option to compute and send SHA256 over data sent (-i).
This is to ensure the correctness of data received.
Data is randomly populated from /dev/urandom.
Tested:
./tcp_mmap -s -z -i
./tcp_mmap -z -H $ADDR -i
SHA256 is correct
./tcp_mmap -s -i
./tcp_mmap -H $ADDR -i
SHA256 is correct
Signed-off-by: Coco Li <lixiaoyan@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20230321081202.2370275-2-lixiaoyan@google.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
When compound pages are enabled, although the mm layer still
returns an array of page pointers, a subset (or all) of them
may have the same page head since a max 180kb skb can span 2
hugepages if it is on the boundary, be a mix of pages and 1 hugepage,
or fit completely in a hugepage. Instead of referencing page head
on all page pointers, use page length arithmetic to only call page
head when referencing a known different page head to avoid touching
a cold cacheline.
Tested:
See next patch with changes to tcp_mmap
Correntess:
On a pair of separate hosts as send with MSG_ZEROCOPY will
force a copy on tx if using loopback alone, check that the SHA
on the message sent is equivalent to checksum on the message received,
since the current program already checks for the length.
echo 1024 > /sys/kernel/mm/hugepages/hugepages-2048kB/nr_hugepages
./tcp_mmap -s -z
./tcp_mmap -H $DADDR -z
SHA256 is correct
received 2 MB (100 % mmap'ed) in 0.005914 s, 2.83686 Gbit
cpu usage user:0.001984 sys:0.000963, 1473.5 usec per MB, 10 c-switches
Performance:
Run neper between adjacent hosts with the same config
tcp_stream -Z --skip-rx-copy -6 -T 20 -F 1000 --stime-use-proc --test-length=30
Before patch: stime_end=37.670000
After patch: stime_end=30.310000
Signed-off-by: Coco Li <lixiaoyan@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20230321081202.2370275-1-lixiaoyan@google.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
It had a purpose back in the days, but today we have a handy helper.
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20230321065826.2044-1-wsa+renesas@sang-engineering.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
When the CPTS clock is synced/adjusted by running linuxptp (ptp4l/phc2sys),
it will cause the TSN EST schedule to drift away over time. This is because
the schedule is driven by the EstF periodic counter whose pulse length is
defined in ref_clk cycles and it does not automatically sync to CPTS clock.
_______
_|
^
expected cycle start time boundary
_______________
_|_|___|_|
^
EstF drifted away -> direction
To fix it, the same PPM adjustment has to be applied to EstF as done to the
PHC CPTS clock, in order to correct the TSN EST cycle length and keep them
in sync.
Drifted cycle:
AM65_CPTS_EVT: 7 e1:01770001 e2:000000ff t:1635968230373377017
AM65_CPTS_EVT: 7 e1:01770001 e2:000000ff t:1635968230373877017
AM65_CPTS_EVT: 7 e1:01770001 e2:000000ff t:1635968230374377017
AM65_CPTS_EVT: 7 e1:01770001 e2:000000ff t:1635968230374877017
AM65_CPTS_EVT: 7 e1:01770001 e2:000000ff t:1635968230375377017
AM65_CPTS_EVT: 7 e1:01770001 e2:000000ff t:1635968230375877023
AM65_CPTS_EVT: 7 e1:01770001 e2:000000ff t:1635968230376377018
AM65_CPTS_EVT: 7 e1:01770001 e2:000000ff t:1635968230376877018
AM65_CPTS_EVT: 7 e1:01770001 e2:000000ff t:1635968230377377018
Stable cycle:
AM65_CPTS_EVT: 7 e1:01770001 e2:000000ff t:1635966863193375473
AM65_CPTS_EVT: 7 e1:01770001 e2:000000ff t:1635966863193875473
AM65_CPTS_EVT: 7 e1:01770001 e2:000000ff t:1635966863194375473
AM65_CPTS_EVT: 7 e1:01770001 e2:000000ff t:1635966863194875473
AM65_CPTS_EVT: 7 e1:01770001 e2:000000ff t:1635966863195375473
AM65_CPTS_EVT: 7 e1:01770001 e2:000000ff t:1635966863195875473
AM65_CPTS_EVT: 7 e1:01770001 e2:000000ff t:1635966863196375473
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Link: https://lore.kernel.org/r/20230321062600.2539544-1-s-vadapalli@ti.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Sometimes we need to know which one of backlog queue can be exactly
long enough to cause some latency when debugging this part is needed.
Thus, we can then separate the display of both.
Signed-off-by: Jason Xing <kernelxing@tencent.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230321015746.96994-1-kerneljasonxing@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Pointer to transport could be checked before allocation of skbuff, thus
there is no need to free skbuff when this pointer is NULL.
Signed-off-by: Arseniy Krasnov <AVKrasnov@sberdevices.ru>
Reviewed-by: Bobby Eshleman <bobby.eshleman@bytedance.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Link: https://lore.kernel.org/r/08d61bef-0c11-c7f9-9266-cb2109070314@sberdevices.ru
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Jiri suggests it reads more naturally to skip the explicit
array size when possible. When we export the symbol we want
to make sure that the size is right but for statics its
not needed.
Link: https://lore.kernel.org/r/20230321044159.1031040-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
