| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The count field in struct trip_stats, representing the number of times
the zone temperature was above the trip point, needs to be incremented
in thermal_debug_tz_trip_up(), for two reasons.
First, if a trip point is crossed on the way up for the first time,
thermal_debug_update_temp() called from update_temperature() does
not see it because it has not been added to trips_crossed[] array
in the thermal zone's struct tz_debugfs object yet. Therefore, when
thermal_debug_tz_trip_up() is called after that, the trip point's
count value is 0, and the attempt to divide by it during the average
temperature computation leads to a divide error which causes the kernel
to crash. Setting the count to 1 before the division by incrementing it
fixes this problem.
Second, if a trip point is crossed on the way up, but it has been
crossed on the way up already before, its count value needs to be
incremented to make a record of the fact that the zone temperature is
above the trip now. Without doing that, if the mitigations applied
after crossing the trip cause the zone temperature to drop below its
threshold, the count will not be updated for this episode at all and
the average temperature in the trip statistics record will be somewhat
higher than it should be.
Fixes: 7ef01f228c9f ("thermal/debugfs: Add thermal debugfs information for mitigation episodes")
Cc :6.8+ <stable@vger.kernel.org> # 6.8+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The VXLAN driver currently does not check if the inner layer2
source-address is valid.
In case source-address snooping/learning is enabled, a entry in the FDB
for the invalid address is created with the layer3 address of the tunnel
endpoint.
If the frame happens to have a non-unicast address set, all this
non-unicast traffic is subsequently not flooded to the tunnel network
but sent to the learnt host in the FDB. To make matters worse, this FDB
entry does not expire.
Apply the same filtering for packets as it is done for bridges. This not
only drops these invalid packets but avoids them from being learnt into
the FDB.
Fixes: d342894c5d2f ("vxlan: virtual extensible lan")
Suggested-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David Bauer <mail@david-bauer.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Eric Dumazet says:
====================
neighbour: convert neigh_dump_info() to RCU
Remove RTNL requirement for "ip neighbour show" command.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
neigh_dump_table() is already relying on RCU protection.
pneigh_dump_table() is using its own protection (tbl->lock)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Change neigh_dump_table() and pneigh_dump_table()
to either return 0 or -EMSGSIZE if not enough
space was available in the skb.
Then neigh_dump_info() can do the same.
This allows NLMSG_DONE to be appended to the current
skb at the end of a dump, saving a couple of recvmsg()
system calls.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In order to remove RTNL protection from neightbl_dump_info()
and neigh_dump_info() later, we need to add
RCU protection to neigh_tables[].
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The kernel build bot identified the following mistake in the recently
merged 860a9bed2651 ("net: dsa: xrs700x: provide own phylink MAC
operations") patch:
drivers/net/dsa/xrs700x/xrs700x.c:714:37: warning: 'xrs700x_phylink_mac_ops' defined but not used [-Wunused-const-variable=]
714 | static const struct phylink_mac_ops xrs700x_phylink_mac_ops = {
| ^~~~~~~~~~~~~~~~~~~~~~~
Fix the omitted assignment of ds->phylink_mac_ops.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Jason Xing says:
====================
locklessly protect left members in struct rps_dev_flow
From: Jason Xing <kernelxing@tencent.com>
Since Eric did a more complicated locklessly change to last_qtail
member[1] in struct rps_dev_flow, the left members are easier to change
as the same.
One thing important I would like to share by qooting Eric:
"rflow is located in rxqueue->rps_flow_table, it is thus private to current
thread. Only one cpu can service an RX queue at a time."
So we only pay attention to the reader in the rps_may_expire_flow() and
writer in the set_rps_cpu(). They are in the two different contexts.
[1]:
https://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next.git/commit/?id=3b4cf29bdab
v3
Link: https://lore.kernel.org/all/20240417062721.45652-1-kerneljasonxing@gmail.com/
1. adjust the protection in a right way (Eric)
v2
1. fix passing wrong type qtail.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is the last member in struct rps_dev_flow which should be
protected locklessly. So finish it.
Signed-off-by: Jason Xing <kernelxing@tencent.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As we can see, rflow->filter can be written/read concurrently, so
lockless access is needed.
Signed-off-by: Jason Xing <kernelxing@tencent.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Removing one unnecessary reader protection and add another writer
protection to finish the locklessly proctection job.
Note: the removed READ_ONCE() is not needed because we only have to protect
the locklessly reader in the different context (rps_may_expire_flow()).
Signed-off-by: Jason Xing <kernelxing@tencent.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Eric Dumazet says:
====================
net_sched: first series for RTNL-less qdisc dumps
Medium term goal is to implement "tc qdisc show" without needing
to acquire RTNL.
This first series makes the requested changes in 14 qdisc.
Notes :
- RTNL is still held in "tc qdisc show", more changes are needed.
- Qdisc returning many attributes might want/need to provide
a consistent set of attributes. If that is the case, their
dump() method could acquire the qdisc spinlock, to pair the
spinlock acquision in their change() method.
V2: Addressed Simon feedback (Thanks a lot Simon)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Instead of relying on RTNL, skbprio_dump() can use READ_ONCE()
annotation, paired with WRITE_ONCE() one in skbprio_change().
Also add a READ_ONCE(sch->limit) in skbprio_enqueue().
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Instead of relying on RTNL, pie_dump() can use READ_ONCE()
annotations, paired with WRITE_ONCE() ones in pie_change().
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Instead of relying on RTNL, hhf_dump() can use READ_ONCE()
annotations, paired with WRITE_ONCE() ones in hhf_change().
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Instead of relying on RTNL, hfsc_dump_qdisc() can use READ_ONCE()
annotation, paired with WRITE_ONCE() one in hfsc_change_qdisc().
Use READ_ONCE(q->defcls) in hfsc_classify() to
no longer acquire qdisc lock from hfsc_change_qdisc().
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Instead of relying on RTNL, fq_pie_dump() can use READ_ONCE()
annotations, paired with WRITE_ONCE() ones in fq_pie_change().
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Instead of relying on RTNL, fq_codel_dump() can use READ_ONCE()
annotations, paired with WRITE_ONCE() ones in fq_codel_change().
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Instead of relying on RTNL, __fifo_dump() can use READ_ONCE()
annotations, paired with WRITE_ONCE() ones in __fifo_init().
Also add missing READ_ONCE(sh->limit) in bfifo_enqueue(),
pfifo_enqueue() and pfifo_tail_enqueue().
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Instead of relying on RTNL, ets_dump() can use READ_ONCE()
annotations, paired with WRITE_ONCE() ones in ets_change().
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Instead of relying on RTNL, codel_dump() can use READ_ONCE()
annotations.
There is no etf_change() yet, this patch imply aligns
this qdisc with others.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Instead of relying on RTNL, codel_dump() can use READ_ONCE()
annotations, paired with WRITE_ONCE() ones in codel_change().
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Instead of relying on RTNL, choke_dump() can use READ_ONCE()
annotations, paired with WRITE_ONCE() ones in choke_change().
v2: added a WRITE_ONCE(p->Scell_log, Scell_log)
per Simon feedback in V1
Removed the READ_ONCE(q->limit) in choke_enqueue()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Instead of relying on RTNL, cbs_dump() can use READ_ONCE()
annotations, paired with WRITE_ONCE() ones in cbs_change().
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Instead of relying on RTNL, cake_dump() can use READ_ONCE()
annotations, paired with WRITE_ONCE() ones in cake_change().
v2: addressed Simon feedback in V1: https://lore.kernel.org/netdev/20240417083549.GA3846178@kernel.org/
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Toke Høiland-Jørgensen <toke@toke.dk>
Reviewed-by: Simon Horman <horms@kernel.org>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Instead of relying on RTNL, fq_dump() can use READ_ONCE()
annotations, paired with WRITE_ONCE() in fq_change()
v2: Addressed Simon feedback in V1: https://lore.kernel.org/netdev/20240416181915.GT2320920@kernel.org/
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
driver needs queue msix vectors and one misc irq vector,
but only queue vectors need irq affinity.
when num_online_cpus is less than chip max msix vectors,
driver will acquire (num_online_cpus + 1) vecotrs, and
call pci_alloc_irq_vectors_affinity functions with affinity
params without setting pre_vectors or post_vectors, it will
cause return error code -ENOSPC.
Misc irq vector is vector 0, driver need to set affinity params
.pre_vectors = 1.
Fixes: 3f703186113f ("net: libwx: Add irq flow functions")
Signed-off-by: Duanqiang Wen <duanqiangwen@net-swift.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The conversion from MIDI2 to MIDI1 UMP messages had a leftover
artifact (superfluous bit shift), and this resulted in the bogus type
check, leading to empty outputs. Let's fix it.
Fixes: e9e02819a98a ("ALSA: seq: Automatic conversion of UMP events")
Cc: <stable@vger.kernel.org>
Link: https://github.com/alsa-project/alsa-utils/issues/262
Message-ID: <20240419100442.14806-1-tiwai@suse.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The Haier Boyue G42 with ALC269VC cannot detect the MIC of headset,
the line out and internal speaker until
ALC269VC_FIXUP_ACER_VCOPPERBOX_PINS quirk applied.
Signed-off-by: Ai Chao <aichao@kylinos.cn>
Cc: <stable@vger.kernel.org>
Message-ID: <20240419082159.476879-1-aichao@kylinos.cn>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
During non-STA management Tx, when source address is same as one of the
link addresses and even when userspace requested Tx on a specific link,
the link ID is not set in the TX control information. Now if the MLD
address is also the same as that of the link address, then mac80211
fills link as "unspecified", since it looks like MLD TX.
This is unexpected, however, since non-STA TX must specify which link
to use. In hwsim, this will (after warnings) result in dropping such
frames as well.
Use and set the link id if the link bss is matching the address and
requested channel.
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Link: https://msgid.link/20240410052705.169865-1-quic_adisi@quicinc.com
Link: https://lore.kernel.org/r/0496fb7e-53cc-476f-8052-985d82fd8d01@quicinc.com
[reword commit message, should spell out hwsim etc.]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Currently whenever link AP beacon is assigned, sdata->u.ap.active flag is
set and whenever it is brought down, the flag is reset. However, with MLO,
all the links of the same MLD would use the same sdata. Hence there is no
need to set/reset for each link up/down. Also, resetting it when only one
of the links went down is not desirable.
Add changes to set the active flag only when first link is assigned
beacon. Similarly, add changes to reset that flag only when last link is
brought down.
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Link: https://msgid.link/20240409094017.3165560-1-quic_adisi@quicinc.com
[remove unnecessary check before constant true assignment]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Add return value documentation for regulatory functions
that are missing it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The return value of regulatory_hint_indoor() is always 0 for
success, and the return value of regulatory_hint_found_beacon()
is always ignored. Make them both have void return.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Use the Return: annotation instead of spelling out "Returns" in
the documentation, for both sta_info_flush()/__sta_info_flush().
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
In the unlikely event that link_use_channel fails while activating a
link, mac80211 would go into a bad state. Unfortunately, we cannot
completely avoid failures from drivers in this case.
However, what we can do is to just continue internally anyway and assume
the driver is going to trigger a recovery flow from its side. Doing that
means that we at least have a consistent state in mac80211 allowing such
a recovery flow to succeed.
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://msgid.link/20240418115219.1129e89f4b55.I6299678353e50e88b55c99b0bce15c64b52c2804@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
There's no need for a label/goto here, the only thing is
that drv_assign_vif_chanctx() must succeed to set 'conf'
and add the new context to the list, the remaining code
is (and must be) the same regardless.
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://msgid.link/20240418115219.a94852030d33.I9d647178ab25636372ed79e5312c68a06e0bf60c@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
When searching for a chanctx for re-use, it's later adjusted and
assigned. It may also be that another one is already assigned to
the link in question, so unassign can also happen. In short, the
driver is called multiple times. During these callbacks, it may
thus change active links (on another interface), which then can
in turn cause the found chanctx (that's going to be reused) to
get removed and freed.
To avoid this, temporarily assign it to the reserved chanctx and
track the link that wants to use it in the reserved_links list.
This causes the ieee80211_chanctx_refcount() to be increased by
one during these operations, thus avoiding the free.
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://msgid.link/20240418115219.94ea84c8ee1e.I0b247dbc0cd937ae6367bc0fc7e8d156b5d5f9b1@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Running "scripts/kernel-doc -Wall -Werror -none include/net/cfg80211.h"
produces many warnings of the form "warning: No description found for
return value of <function>", so make sure all of them have a Return:
clause. In some instances also add a Context: clause.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://msgid.link/20240417-cfg80211-kdoc-v1-1-d54cb7143417@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
If a custom regulatory is being used, use the 6GHz regulatory for
testing 6GHz channels.
Signed-off-by: Chaitanya Tata <Chaitanya.Tk17@gmail.com>
Link: https://msgid.link/20240417074022.423432-1-Chaitanya.Tk17@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
If the RSSI of a link is low enough, don't use it for EMLSR.
If EMLSR is already active and the RSSI of one of the links gets low,
exit EMLSR by deactivating that link.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240416134215.73263c000263.Ieb2b18855a2719b5e18ad2fa8a3e855ca4e23938@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
We can't be an EMLSR while suspended with wowlan. De-activate the
secondary link upon wowlan entring.
Set the blocking reason upon suspension and clear it upon resume.
Signed-off-by: Yedidya Benshimol <yedidya.ben.shimol@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240416134215.6ea884b3f095.I84233cb1c79ba538defafb8ddb983c47f04a400a@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
In EMLSR we need to track the RSSI of both links, and exit if the RSSI of
one of the links got too low.
For that request the FW to send statistics every 5 seconds when in EMLSR.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240416134215.6e19d596d77f.Ica2a75a031b1bced0dc2e18c5d365b5eb0d3ec07@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
mac80211 invokes the driver callback drv_can_activate_links() from
ieee80211_set_active_links to verify it can activate the desired link
combination.
However, ieee80211_set_active_links is called with more than one link in
2 cases:
- After driver's link selection decided to enter EMLSR
- From debugfs, for testing purposes.
For both cases there is no need to recompute all the considerations
determining whether to activate EMLSR.
Instead, only check if the vif is not blocked for EMLSR.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Link: https://msgid.link/20240416134215.202cf5a9ef2c.I65e4698b730a8652ad8d1c01420aabb41a1d04fd@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Address scenarios where repeated entry and exit from EMLSR occur, such as
encountering missed beacons on a specific link,
while still discovering that link during a scan.
To mitigate this, introduce the EMLSR prevention mechanism, which operates
as follows:
- On each exit from EMLSR event, record the timestamp and the exit
reason.
- If two consecutive exits happen for the same reason within a
400-second window, enforce a 300-second EMLSR prevention.
- If a third exit for the same reason occurs within 400 seconds from the
second exit, enforce an extended EMLSR prevention of 600 seconds.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Link: https://msgid.link/20240416134215.d820ee98b300.I6406db40cf25eabdba602afd783466473b909216@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
In case of more than 6 missed beacons on one of the links,
exit EMLSR by deactivating that link.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240416134215.f9111c79cb53.Ie95ea60149a9bc4367f6b338b37c8635051351ba@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
It's dangerous to re-initialize works repeatedly, especially
delayed ones that have an associated timer, and even more so
if they're not necessarily canceled inbetween. This can be
the case for these workers here during FW restart scenarios,
so make sure to initialize it only once.
While at it, also ensure it is cancelled correctly.
Fixes: f67806140220 ("iwlwifi: mvm: disconnect in case of bad channel switch parameters")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240416134215.ddf8eece5eac.I4164f5c9c444b64a9abbaab14c23858713778e35@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
There are reasons for which we need to exit EMLSR, but not to block it
completely, and there are reasons for which we need to block EMLSR.
For both reason types we have the enum iwl_mvm_esr_state, when the
blocking reasons are stored in the `mvmvif::esr_disable_reason` bitmap.
This change introduces the APIs to use in the different cases:
- iwl_mvm_exit_esr - will exit from EMLSR mode.
- iwl_mvm_block_esr - will update the bitmap and exit EMLSR, to
be used for the blocking reasons only.
- iwl_mvm_unblock_esr - will update the bitmap. To be used for the
blocking reasons only.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Link: https://msgid.link/20240416134215.d54142a75876.I552926065521f5f848c37b0bd845494bd7865fb7@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Replaces the current logic with a new algorithm based on the link
grading introduced in a previous patch.
The new selection algorithm will be invoked upon successful scan to ensure
it has the necessary updated data it needs.
This update delegates the selection logic as the primary link
determiner in EMLSR mode, storing it in mvmvif to avoid repeated
calculations, as the result may vary.
Additionally, includes tests for iwl_mvm_valid_link_pair to validate
link pairs for EMLSR.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Link: https://msgid.link/20240416134215.309fb1b3fe44.I5baf0c293c89a5a28bd1a6386bf9ca6d2bf61ab8@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The functions that are link related, so they should be in link.c and
not in mld-mac80211.c. Move them.
Also move the different prototypes to the right place in mvm.h
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Link: https://msgid.link/20240416134215.e7c368256fa0.I6b15805a7c8a75d1814f1a829601daf4d3788731@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Currenty iwl_mvm_mld_select_links() doesn't fully check that
EMLSR is allowed before selecting the 2 best links.
Although it will fail in ieee80211_set_active_links(), it is preferred
to avoid the redundent calculations.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Link: https://msgid.link/20240416134215.3578a93feb1a.I1cd91608bb73fbe19b8dfdf90e14ce40b98c3430@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
