| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Use EXPORT_SYMBOL_GPL instead of EXPORT_SYMBOL.
Signed-off-by: Tadeusz Struk <tadeusz.struk@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
iwlwifi:
* fix a memory leak, we leaked memory each time the module
was loaded.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Hariprasad Shenai says:
====================
cxgb4 FW macro changes for new FW
Fix to dump device log even in the case of firmware crash. Also
incorporates changes for new FW.
This patch series has been created against net tree and includes patches on
cxgb4 driver.
We have included all the maintainers of respective drivers. Kindly review the
change and let us know in case of any review comments.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add new Common Code routines to retrieve Firmware Device Log
parameters from PCIE_FW_PF[7]. The firmware initializes its Device Log very
early on and stores the parameters for its location/size in that register.
Using the parameters from the register allows us to access the Firmware
Device Log even when the firmware crashes very early on or we're not
attached to the firmware
Based on original work by Casey Leedom <leedom@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adds new macro and few macro changes for fw version 1.13.32.0 also
changes version string in driver to match 1.13.32.0
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This allows drivers to request per-vif and per-sta-tid queues from which
they can pull frames. This makes it easier to keep the hardware queues
short, and to improve fairness between clients and vifs.
The task of scheduling packet transmission is left up to the driver -
queueing is controlled by mac80211. Drivers can only dequeue packets by
calling ieee80211_tx_dequeue. This makes it possible to add active queue
management later without changing drivers using this code.
This can also be used as a starting point to implement A-MSDU
aggregation in a way that does not add artificially induced latency.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
[resolved minor context conflict, minor changes, endian annotations]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This changes a couple of messages from sdata_info to sdata_dbg.
This should reduce some log spam, as reported here:
https://bugzilla.redhat.com/show_bug.cgi?id=1206468
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This patch adds the statistical descriptor "standard deviation"
to better describe the current properties of Minstrel and
Minstrel-HTs success probability distribution. The standard
deviation (SD) is calculated as exponential weighted moving
standard deviation (EWMSD) and its current value is added as
new column in all rc_stats (in debugfs).
Signed-off-by: Thomas Huehn <thomas@net.t-labs.tu-berlin.de>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This patch reduces the calculation costs of the EWMA macro from
"2x multiplication and 1 addition" down to "1x multiplication and
2x additions". This slightly improves performance depending on the
CPU architecture.
Signed-off-by: Thomas Huehn <thomas@net.t-labs.tu-berlin.de>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This patch adds the new statistic "maximum possible lossless
throughput" to Minstrels and Minstrel-HTs rc_stats (in debugfs). This
enables comprehensive comparison between current per-rate throughput
and max. achievable per-rate throughput.
Signed-off-by: Thomas Huehn <thomas@net.t-labs.tu-berlin.de>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This patch moves Minstrels and Minstrel-HTs per-rate throughput
calculation (EWMA(thr)) into a dedicated function to be called.
Therefore the variable "unsigned int cur_tp" within struct
"minstrel_rate_stats" becomes obsolete. and is removed to free
up its space.
Signed-off-by: Thomas Huehn <thomas@net.t-labs.tu-berlin.de>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This patch ensures a consistent usage of variable names for type
"minstrel_rate_stats" to be used as "mrs" and from type minstrel_rate
as "mr" across both Minstrel & Minstrel-HT. In addition some
variable and function names got changed to more meaningful ones.
Signed-off-by: Thomas Huehn <thomas@net.t-labs.tu-berlin.de>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This patch unifies the calculation of Minstrels and Minstrel-HTs
per-rate statistic. The new common function minstrel_calc_rate_stats()
is called when a statistic update is performed.
Signed-off-by: Thomas Huehn <thomas@net.t-labs.tu-berlin.de>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This patch adds a new debugfs file "rc_stats_csv" to output
Minstrel-HTs statistics in a common csv format that is easy
to parse.
Signed-off-by: Thomas Huehn <thomas@net.t-labs.tu-berlin.de>
Signed-off-by: Stefan Venz <ikstream86@gmail.com>
Acked-by: Felix Fietkau <nbd@openwrt.org>
[remove printing current time of day]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This patch adds a new debugfs file "rc_stats_csv" to output Minstrels
statistics in a common csv format that is easy to parse.
Signed-off-by: Thomas Huehn <thomas@net.t-labs.tu-berlin.de>
Signed-off-by: Stefan Venz <ikstream86@gmail.com>
Acked-by: Felix Fietkau <nbd@openwrt.org>
[remove printing current time of day]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Move ~2KB of strings in each driver from data to text.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
Major changes:
ath9k:
* add Active Interference Cancellation, a method implemented in the HW
to counter WLAN RX > sensitivity degradation when BT is transmitting
at the same time. This feature is supported by cards like WB222
based on AR9462.
iwlwifi:
* Location Aware Regulatory was added by Arik
* 8000 device family work
* update to the BT Coex firmware API
brmcfmac:
* add new BCM43455 and BCM43457 SDIO device support
* add new BCM43430 SDIO device support
wil6210:
* take care of AP bridging
* fix NAPI behavior
* found approach to achieve 4*n+2 alignment of Rx frames
rt2x00:
* add new rt2800usb device DWA 130
rtlwifi:
* add USB ID for D-Link DWA-131
* add USB ID ASUS N10 WiFi dongle
mwifiex:
* throughput enhancements
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
This contains just a single fix for a crash I happened to randomly
run into today during testing. It's clearly been around for a while,
but is pretty hard to trigger, even when I tried explicitly (and
modified the code to make it more likely) it rarely did.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
pull-request: can-next 2015-04-01
this is a pull request of 5 patches for net-next/master.
There are two patches for the ems_usb driver by Gerhard Uttenthaler and
me, which fix sparse endianess warnings. Oliver Hartkopp adds two
patches to improve and extend the CAN-ID filter handling on RAW CAN
sockets. The last patch is by me, it silences an uninitialized variable
warning in the peak_usb driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, MoCA fixed PHYs are always in link-up state, regardless of
whether the link is actually up or not.
Add code to properly detect MoCA link state changes and to reflect the
new state in MoCA fixed PHY. Only GENET V3 and V4 MACs are capable of
detecting MoCA link state changes.
The code works as follows:
1. GENET MAC detects MoCA link state change and issues UMAC_IRQ_LINK_UP
or UMAC_IRQ_LINK_DOWN interrupt.
2. Link up/down interrupt is processed in bcmgenet_irq_task(), which
calls phy_mac_interrupt().
3. phy_mac_interrupt() updates the fixed PHY phydev->link and kicks
the PHY state machine.
4. PHY state machine proceeds to read the fixed PHY link status
register.
5. When the fixed PHY link status register is being read, the new
function bcmgenet_fixed_phy_link_update() gets called. It copies
the fixed PHY phydev->link value to the fixed PHY status->link.
6. PHY state machine receives the new link state of the fixed PHY.
7. MoCA fixed PHY link state now correctly reflects the real MoCA
hardware link state.
Signed-off-by: Petri Gynther <pgynther@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU fixes from Joerg Roedel:
"This contains fixes for:
- a VT-d issue where hardware domain-ids might be freed while still
in use.
- an ipmmu-vmsa issue where where the device-table was not zero
terminated
- unchecked register access issue in the arm-smmu driver"
* tag 'iommu-fixes-v4.0-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/vt-d: Remove unused variable
iommu: ipmmu-vmsa: Add terminating entry for ipmmu_of_ids
iommu/vt-d: Detach domain *only* from attached iommus
iommu/arm-smmu: fix ARM_SMMU_FEAT_TRANS_OPS condition
|
|
Since commit 8e7094694396 ("lguest: add a dummy PCI host bridge.")
lguest uses PCI, but it needs you to frob the ports directly.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull lazytime fixes from Ted Ts'o:
"This fixes a problem in the lazy time patches, which can cause
frequently updated inods to never have their timestamps updated.
These changes guarantee that no timestamp on disk will be stale by
more than 24 hours"
* tag 'lazytime_fix' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
fs: add dirtytime_expire_seconds sysctl
fs: make sure the timestamps for lazytime inodes eventually get written
|
|
When we access the triggers we need to make sure that the
data we expect was actually provided by the firmware file.
Check this when we decode the triggers from the firmware
file.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
Pull nfsd fixes from Bruce Fields:
"Two main issues:
- We found that turning on pNFS by default (when it's configured at
build time) was too aggressive, so we want to switch the default
before the 4.0 release.
- Recent client changes to increase open parallelism uncovered a
serious bug lurking in the server's open code.
Also fix a krb5/selinux regression.
The rest is mainly smaller pNFS fixes"
* 'for-4.0' of git://linux-nfs.org/~bfields/linux:
sunrpc: make debugfs file creation failure non-fatal
nfsd: require an explicit option to enable pNFS
NFSD: Fix bad update of layout in nfsd4_return_file_layout
NFSD: Take care the return value from nfsd4_encode_stateid
NFSD: Printk blocklayout length and offset as format 0x%llx
nfsd: return correct lockowner when there is a race on hash insert
nfsd: return correct openowner when there is a race to put one in the hash
NFSD: Put exports after nfsd4_layout_verify fail
NFSD: Error out when register_shrinker() fail
NFSD: Take care the return value from nfsd4_decode_stateid
NFSD: Check layout type when returning client layouts
NFSD: restore trace event lost in mismerge
|
|
Since 39b2bbe3d715 (gpio: add flags argument to gpiod_get*() functions)
which appeared in v3.17-rc1, the gpiod_get* functions take an additional
parameter that allows to specify direction and initial value for output.
Moreover use devm_gpiod_get_optional instead of ignoring all errors
returned by devm_gpiod_get and simplify accordingly.
The result is more strict error handling which is good.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The tty_name member of struct ser_device is never set or used, so it
can be removed. (The definition of struct ser_device is private to
this .c file, and the identifier tty_name only occurs in this one
place.)
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Yuval Mintz says:
====================
bnx2x: kdump related fixes
This patch series aims to fix bnx2x driver issues when loading in kdump kernel.
Both issues fixed here would be fatal to the device, requiring full reset of
the system in order to recover, preventing the device from serving its purpose
in the kdump environment.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When IOMM-vtd is active, once main kernel crashes unfinished DMAE transactions
will be blocked, putting the HW in an error state which will cause further
transactions to timeout.
Current employed logic uses wrong macros, causing the first function to be the
only function that cleanups that error state during its probe/load.
This patch allows all the functions to successfully re-load in kdump kernel.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When running in a kdump kernel, it's very likely that due to sync. loss with
management firmware the first PCI function to probe and reach the previous
unload flow would decide it can reset the chip and continue onward. While doing
so, it will only close its own Rx port.
On a 4-port device where 2nd port on engine is a 1g-port, the 2nd port would
allow ingress traffic after the chip is reset [assuming it was active on the
first kernel]. This would later cause a HW attention.
This changes driver flow to close both ports' 1g capabilities during the
previous driver unload flow prior to the chip reset.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Handle VERSION Rx protocol packets. We should respond to a VERSION packet
with a string indicating the Rx version. This is a maximum of 64 characters
and is padded out to 65 chars with NUL bytes.
Note that other AFS clients use the version request as a NAT keepalive so we
need to handle it rather than returning an abort.
The standard formulation seems to be:
<project> <version> built <yyyy>-<mm>-<dd>
for example:
" OpenAFS 1.6.2 built 2013-05-07 "
(note the three extra spaces) as obtained with:
rxdebug grand.mit.edu -version
from the openafs package.
Signed-off-by: David Howells <dhowells@redhat.com>
|
|
afs_send_empty_reply() doesn't require an iovec array with which to initialise
the msghdr, but can pass NULL instead.
Suggested-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David Howells <dhowells@redhat.com>
|
|
Use iov_iter_count() in rxrpc_send_data() to get the remaining data length
instead of using the len argument as the len argument is now redundant.
Signed-off-by: David Howells <dhowells@redhat.com>
|
|
Don't call skb_add_data() in rxrpc_send_data() if there's no data to copy and
also skip the calculations associated with it in such a case.
Signed-off-by: David Howells <dhowells@redhat.com>
|
|
This commit:
commit af2b040e470b470bfc881981db3c796072853eae
Author: Al Viro <viro@zeniv.linux.org.uk>
Date: Thu Nov 27 21:44:24 2014 -0500
Subject: rxrpc: switch rxrpc_send_data() to iov_iter primitives
incorrectly changes a do-while loop into a while loop in rxrpc_send_data().
Unfortunately, at least one pass through the loop is required - even if
there is no data - so that the packet the closes the send phase can be
sent if MSG_MORE is not set.
Signed-off-by: David Howells <dhowells@redhat.com>
|
|
There's an issue with the way the RX A-MPDU reorder timer is
deleted that can cause a kernel crash like this:
* tid_rx is removed - call_rcu(ieee80211_free_tid_rx)
* station is destroyed
* reorder timer fires before ieee80211_free_tid_rx() runs,
accessing the station, thus potentially crashing due to
the use-after-free
The station deletion is protected by synchronize_net(), but
that isn't enough -- ieee80211_free_tid_rx() need not have
run when that returns (it deletes the timer.) We could use
rcu_barrier() instead of synchronize_net(), but that's much
more expensive.
Instead, to fix this, add a field tracking that the session
is being deleted. In this case, the only re-arming of the
timer happens with the reorder spinlock held, so make that
code not rearm it if the session is being deleted and also
delete the timer after setting that field. This ensures the
timer cannot fire after ___ieee80211_stop_rx_ba_session()
returns, which fixes the problem.
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The ASRock Q1900DC-ITX mainboard (Baytrail-D) hangs randomly in
both BIOS and UEFI mode while rebooting unless reboot=pci is
used. Add a quirk to reboot via the pci method.
The problem is very intermittent and hard to debug, it might succeed
rebooting just fine 40 times in a row - but fails half a dozen times
the next day. It seems to be slightly less common in BIOS CSM mode
than native UEFI (with the CSM disabled), but it does happen in either
mode. Since I've started testing this patch in late january, rebooting
has been 100% reliable.
Most of the time it already hangs during POST, but occasionally it
might even make it through the bootloader and the kernel might even
start booting, but then hangs before the mode switch. The same symptoms
occur with grub-efi, gummiboot and grub-pc, just as well as (at least)
kernel 3.16-3.19 and 4.0-rc6 (I haven't tried older kernels than 3.16).
Upgrading to the most current mainboard firmware of the ASRock
Q1900DC-ITX, version 1.20, does not improve the situation.
( Searching the web seems to suggest that other Bay Trail-D mainboards
might be affected as well. )
--
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Cc: <stable@vger.kernel.org>
Cc: Matt Fleming <matt.fleming@intel.com>
Link: http://lkml.kernel.org/r/20150330224427.0fb58e42@mir
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
IIO fixes for 4.0 set 4
A couple more IIO fixes.
* Fix check for HAS_IOMEM in the cc100001_adc driver to avoid build errors.
Rather curiously it was ORed with Regulator and clock support.
* vf610 driver was trying to use an ADC clock outside the possible
spec on some boards. The driver assumed a fixed clock speed previously
across all boards, but that is not true. This fix ensures that the
reported frequency is correct on all boards.
* The adis imu common code directly set the current trigger to the
driver supplied one. Unfortunately this didn't increase the use count
leading to a double free via a particular path of changing the trigger
then removing the driver.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for v4.0-rc6
Here are a few new device IDs.
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
uninitialized var
This patch silences the compiler warning:
drivers/net/can/usb/peak_usb/pcan_usb_fd.c: In function 'pcan_usb_fd_send_cmd':
drivers/net/can/usb/peak_usb/pcan_usb_fd.c:185:6: warning: 'err' may be used uninitialized in this function [-Wuninitialized]
by initialising the variable as 0.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
We have to stop iterating on the rule expressions if the cgroup
mismatches. Moreover, make sure a non-full socket from the input path
leads us to a crash.
Fixes: ce67417 ("netfilter: nft_meta: add cgroup support")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
The CAN_RAW socket can set multiple CAN identifier specific filters that lead
to multiple filters in the af_can.c filter processing. These filters are
indenpendent from each other which leads to logical OR'ed filters when applied.
This socket option joines the given CAN filters in the way that only CAN frames
are passed to user space that matched *all* given CAN filters. The semantic for
the applied filters is therefore changed to a logical AND.
This is useful especially when the filterset is a combination of filters where
the CAN_INV_FILTER flag is set in order to notch single CAN IDs or CAN ID
ranges from the incoming traffic.
As the raw_rcv() function is executed from NET_RX softirq the introduced
variables are implemented as per-CPU variables to avoid extensive locking at
CAN frame reception time.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The CAN_RAW socket can set multiple CAN identifier specific filters that lead
to multiple filters in the af_can.c filter processing. These filters are
indenpendent from each other which leads to logical OR'ed filters when applied.
This patch makes sure that every CAN frame which is filtered for a specific
socket is only delivered once to the user space. This is independent from the
number of matching CAN filters of this socket.
As the raw_rcv() function is executed from NET_RX softirq the introduced
variables are implemented as per-CPU variables to avoid extensive locking at
CAN frame reception time.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
While originally only being intended for outgoing traffic, commit
a00e76349f35 ("netfilter: x_tables: allow to use cgroup match for
LOCAL_IN nf hooks") enabled xt_cgroups for the NF_INET_LOCAL_IN hook
as well, in order to allow for nfacct accounting.
Besides being currently limited to early demuxes only, commit
a00e76349f35 forgot to add a check if we deal with full sockets,
i.e. in this case not with time wait sockets. TCP time wait sockets
do not have the same memory layout as full sockets, a lower memory
footprint and consequently also don't have a sk_classid member;
probing for sk_classid member there could potentially lead to a
crash.
Fixes: a00e76349f35 ("netfilter: x_tables: allow to use cgroup match for LOCAL_IN nf hooks")
Cc: Alexey Perevalov <a.perevalov@samsung.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
This patch restructures the rc_stats debugfs table of Minstrel-HT in
order to achieve better human readability. A new layout of the
statistics and a new header is added. In addition to the old layout
there are two new columns of information added:
idx - representing the rate index of each rate in mac80211 which
can be used to set specific rates as fixed rate via debugfs
airtime - the tx-time in micro seconds that a 1200 Byte packet
takes to be transmitted over the air at the given rate
The old layout of rc_stats:
type rate tpt eprob *prob ret *ok(*cum) ok( cum)
HT20/LGI MCS0 5.6 100.0 100.0 1 0( 0) 1( 1)
HT20/LGI B MCS1 10.5 100.0 100.0 0 0( 0) 1( 1)
HT20/LGI A MCS2 14.8 100.0 100.0 0 0( 0) 1( 1)
...
is changed into this new layout:
best ________rate______ __statistics__ ________last_______ ______sum-of________
mode guard # rate [name idx airtime] [ ø(tp) ø(prob)] [prob.|retry|suc|att] [#success | #attempts]
HT20 LGI 1 MCS0 0 1480 0.0 0.0 0.0 1 0 0 0 0
HT20 LGI 1 B MCS1 1 740 10.5 100.0 100.0 0 0 0 1 1
HT20 LGI 1 A MCS2 2 496 14.8 100.0 100.0 0 0 0 1 1
...
Signed-off-by: Thomas Huehn <thomas@net.t-labs.tu-berlin.de>
Signed-off-by: Stefan Venz <ikstream86@gmail.com>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This patch restructures the rc_stats debugfs table of Minstrel in
order to achieve better human readability. A new layout of the
statistics and a new header is added. In addition to the old layout
there are two new columns of information added:
idx - representing the rate index of each rate in mac80211 which
can be used to set specific rates as fixed rate via debugfs
airtime - the tx-time in micro seconds that a 1200 Byte packet
takes to be transmitted over the air at the given rate
The old layout of rc_stats:
rate tpt eprob *prob ret *ok(*cum) ok( cum)
DP 1 0.9 93.5 100.0 1 0( 0) 2( 2)
2 0.4 40.0 100.0 0 0( 0) 4( 10)
5.5 0.0 0.0 0.0 0 0( 0) 0( 0)
...
is changed into this new layout:
best _______rate_____ __statistics__ ________last_______ ______sum-of________
rate [name idx tx-time] [ ø(tp) ø(prob)] [prob.|retry|suc|att] [#success | #attempts]
DP 1 0 9738 0.9 93.5 100.0 1 1 1 2 2
2 1 4922 0.4 40.0 100.0 1 0 0 4 10
5.5 2 1858 0.0 0.0 0.0 2 0 0 0 0
...
Signed-off-by: Thomas Huehn <thomas@net.t-labs.tu-berlin.de>
Signed-off-by: Stefan Venz <ikstream86@gmail.com>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Patch eeca9fce1d71a4955855ceb0c3b13c1eb9db27c1 (cfg80211: Schedule
timeout for all CRDA call) introduced a regression, where in case
that crda is not installed (or not configured properly etc.), the
regulatory core will needlessly continue to call it, polluting the
log with the following log:
"cfg80211: Calling CRDA to update world regulatory domain"
Fix this by limiting the number of continuous CRDA request failures.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Add support for element timeouts to nft_hash. The lookup and walking
functions are changed to ignore timed out elements, a periodic garbage
collection task cleans out expired entries.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
GC is expected to happen asynchrously to the netlink interface. In the
netlink path, both insertion and removal of elements consist of two
steps, insertion followed by activation or deactivation followed by
removal, during which the element must not be freed by GC.
The synchronization helpers use an unused bit in the genmask field to
atomically mark an element as "busy", meaning it is either currently
being handled through the netlink API or by GC.
Elements being processed by GC will never survive, netlink will simply
ignore them. Elements being currently processed through netlink will be
skipped by GC and reprocessed during the next run.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Add helpers for GC batch destruction: since element destruction needs
a RCU grace period for all set implementations, add some helper functions
for asynchronous batch destruction. Elements are collected in a batch
structure, which is asynchronously released using RCU once its full.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
