| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The w5100 driver currently only supports direct and indirect bus
interface mode which use MMIO space for accessing w5100 registers.
In order to support SPI interface mode which is supported by W5100 chip,
this makes the bus interface abstraction layer more generic so that
separated w5100-spi driver can use w5100 driver as core module.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Mike Sinkovsky <msink@permonline.ru>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Instead of sprinkle mmiowb over the driver code, move it into primary
register write callbacks. (w5100_write, w5100_write16, w5100_writebuf)
This is a preparation for supporting SPI interface which doesn't use
MMIO for accessing w5100 registers.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Mike Sinkovsky <msink@permonline.ru>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We only need to do the synchronize_net dance once for both, ipv4 and
ipv6 sockets, thus removing one synchronize_net in case both sockets get
dismantled.
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Due to the fact that the udp socket is destructed asynchronously in a
work queue, we have some nondeterministic behavior during shutdown of
vxlan tunnels and creating new ones. Fix this by keeping the destruction
process synchronous in regards to the user space process so IFF_UP can
be reliably set.
udp_tunnel_sock_release destroys vs->sock->sk if reference counter
indicates so. We expect to have the same lifetime of vxlan_sock and
vxlan_sock->sock->sk even in fast paths with only rcu locks held. So
only destruct the whole socket after we can be sure it cannot be found
by searching vxlan_net->sock_list.
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Jiri Benc <jbenc@redhat.com>
Cc: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
|
When __vlan_insert_tag() fails from skb_vlan_push() path due to the
skb_cow_head(), we need to undo the __skb_push() in the error path
as well that was done earlier to move skb->data pointer to mac header.
Moreover, I noticed that when in the non-error path the __skb_pull()
is done and the original offset to mac header was non-zero, we fixup
from a wrong skb->data offset in the checksum complete processing.
So the skb_postpush_rcsum() really needs to be done before __skb_pull()
where skb->data still points to the mac header start and thus operates
under the same conditions as in __vlan_insert_tag().
Fixes: 93515d53b133 ("net: move vlan pop/push functions into common code")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When tested the PHY SGMII Loopback:
1.set the LOOPBACK bit,
2.set the autoneg to AUTONEG_DISABLE, it calls the
genphy_setup_forced which will clear the bit.
The BMCR_LOOPBACK bit should be preserved.
As Florian pointed out that other bits should be preserved too.
So I make the BMCR_ISOLATE and BMCR_PDOWN as well.
Signed-off-by: Weidong Wang <wangweidong1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull block fixes from Jens Axboe:
"A few fixes for the current series. This contains:
- Two fixes for NVMe:
One fixes a reset race that can be triggered by repeated
insert/removal of the module.
The other fixes an issue on some platforms, where we get probe
timeouts since legacy interrupts isn't working. This used not to
be a problem since we had the worker thread poll for completions,
but since that was killed off, it means those poor souls can't
successfully probe their NVMe device. Use a proper IRQ check and
probe (msi-x -> msi ->legacy), like most other drivers to work
around this. Both from Keith.
- A loop corruption issue with offset in iters, from Ming Lei.
- A fix for not having the partition stat per cpu ref count
initialized before sending out the KOBJ_ADD, which could cause user
space to access the counter prior to initialization. Also from
Ming Lei.
- A fix for using the wrong congestion state, from Kaixu Xia"
* 'for-linus' of git://git.kernel.dk/linux-block:
block: loop: fix filesystem corruption in case of aio/dio
NVMe: Always use MSI/MSI-x interrupts
NVMe: Fix reset/remove race
writeback: fix the wrong congested state variable definition
block: partition: initialize percpuref before sending out KOBJ_ADD
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm fixes from Ross Zwisler:
"Two fixes:
- Fix memcpy_from_pmem() to fallback to memcpy() for architectures
where CONFIG_ARCH_HAS_PMEM_API=n.
- Add a comment explaining why we write data twice when clearing
poison in pmem_do_bvec().
This has passed a boot test on an X86_32 config, which was the
architecture where issue #1 above was first noticed"
Dan Williams adds:
"We're giving this multi-maintainer setup a shot, so expect libnvdimm
pull requests from either Ross or I going forward"
* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
libnvdimm, pmem: clarify the write+clear_poison+write flow
pmem: fix BUG() error in pmem.h:48 on X86_32
|
|
Pull MTD fix from Brian Norris:
"One MTD fix for v4.6-rc4:
In the v4.4 cycle, we relaxed the requirement for assigning
mtd->owner, but we didn't remove this error case. It's hit only
by drivers that are both:
(a) using nand_scan() directly
and
(b) built as modules
We haven't seen explicit complaints about this (most use cases don't
fit one or both of the above), but we should definitely not be
BUG()'ing here"
* tag 'for-linus-20160415' of git://git.infradead.org/linux-mtd:
mtd: nand: Drop mtd.owner requirement in nand_scan
|
|
Pull MMC fixes from Ulf Hansson:
"Here are a couple of mmc fixes intended for v4.6 rc4.
Regarding the fix for the regression about mmcblk device indexes. The
approach taken to solve the problem seems to be good enough. There
were some discussions around the solution, but it seems like people
were happy about it in the end.
MMC core:
- Restore similar old behaviour when assigning mmcblk device indexes
MMC host:
- tegra: Disable UHS-I modes for Tegra124 to fix regression"
* tag 'mmc-v4.6-rc3' of git://git.linaro.org/people/ulf.hansson/mmc:
mmc: tegra: Disable UHS-I modes for Tegra124
mmc: block: Use the mmc host device index as the mmcblk device index
|
|
Pull drm fixes from Dave Airlie:
"This contains fixes for exynos, amdgpu, radeon, i915 and qxl.
It also contains some fixes to the core drm edid parser.
qxl:
- fix for a cursor hotspot issue
radeon:
- some MST fixes that I've been running locally and make my monitor a
bit happier
exynos:
- fix some regressions and build fixes
amdgpu:
- a couple of small fixes
i915:
- two DP MST fixes and a couple of other regression fixes
Nothing too out of the ordinary or surprising at this point"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/exynos: Use VIDEO_SAMSUNG_S5P_G2D=n as G2D Kconfig dependency
drm/exynos: fix a warning message
drm/exynos: mic: fix an error code
drm/exynos: fimd: fix broken dp_clock control
drm/exynos: build fbdev code conditionally
drm/exynos: fix adjusted_mode pointer in exynos_plane_mode_set
drm/exynos: fix error handling in exynos_drm_subdrv_open
drm/amd/amdgpu: fix irq domain remove for tonga ih
drm/i915: fix deadlock on lid open
drm/radeon: use helper for mst connector dpms.
drm/radeon/mst: port some MST setup code from DAL.
drm/amdgpu: add invisible pin size statistic
drm/edid: Fix DMT 1024x768@43Hz (interlaced) timings
drm/i915: Exit cherryview_irq_handler() after one pass
drm/i915: Call intel_dp_mst_resume() before resuming displays
drm/i915: Fix race condition in intel_dp_destroy_mst_connector()
drm/edid: Fix parsing of EDID 1.4 Established Timings III descriptor
drm/edid: Fix EDID Established Timings I and II
drm/qxl: fix cursor position with non-zero hotspot
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull parisc ftrace fixes from Helge Deller:
"This is (most likely) the last pull request for v4.6 for the parisc
architecture.
It fixes the FTRACE feature for parisc, which is horribly broken since
quite some time and doesn't even compile. This patch just fixes the
bare minimum (it actually removes more lines than it adds), so that
the function tracer works again on 32- and 64bit kernels.
I've queued up additional patches on top of this patch which e.g. add
the syscall tracer, but those have to wait for the merge window for
v4.7."
* 'parisc-4.6-4' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Fix ftrace function tracer
|
|
Xin Long says:
====================
sctp: support sctp_diag in kernel
This patchset will add sctp_diag module to implement diag interface on
sctp in kernel.
For a listening sctp endpoint, we will just dump it's ep info.
For a sctp connection, we will the assoc info and it's ep info.
The ss dump will looks like:
[iproute2]# ./misc/ss --sctp -n -l
State Recv-Q Send-Q Local Address:Port Peer Address:Port
LISTEN 0 128 172.16.254.254:8888 *:*
LISTEN 0 5 127.0.0.1:1234 *:*
LISTEN 0 5 127.0.0.1:1234 *:*
- ESTAB 0 0 127.0.0.1%lo:1234 127.0.0.1:4321
LISTEN 0 128 172.16.254.254:8888 *:*
- ESTAB 0 0 172.16.254.254%eth1:8888 172.16.253.253:8888
- ESTAB 0 0 172.16.254.254%eth1:8888 172.16.1.1:8888
- ESTAB 0 0 172.16.254.254%eth1:8888 172.16.1.2:8888
- ESTAB 0 0 172.16.254.254%eth1:8888 172.16.2.1:8888
- ESTAB 0 0 172.16.254.254%eth1:8888 172.16.2.2:8888
- ESTAB 0 0 172.16.254.254%eth1:8888 172.16.3.1:8888
- ESTAB 0 0 172.16.254.254%eth1:8888 172.16.3.2:8888
LISTEN 0 0 127.0.0.1:4321 *:*
- ESTAB 0 0 127.0.0.1%lo:4321 127.0.0.1:1234
The entries with '- ESTAB' are the assocs, some of them may belong to
the same endpoint. So we will dump the parent endpoint first, like the
entry with 'LISTEN'. then dump the assocs. ep and assocs entries will
be dumped in right order so that ss can show them in tree format easily.
Besides, this patchset also simplifies sctp proc codes, cause it has
some similar codes with sctp diag in sctp transport traversal.
v1->v2:
1. inet_diag_get_handler needs to return it as const.
2. merge 5/7 into 2/7 of v1.
v2->v3:
do some improvements and fixes in patch 1-4, see the details in
each patch's comment.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When rhashtable_walk_init return err, no release function should be
called, and when rhashtable_walk_start return err, we should only invoke
rhashtable_walk_exit to release the source.
But now when sctp_transport_walk_start return err, we just call
rhashtable_walk_stop/exit, and never care about if rhashtable_walk_init
or start return err, which is so bad.
We will fix it by calling rhashtable_walk_exit if rhashtable_walk_start
return err in sctp_transport_walk_start, and if sctp_transport_walk_start
return err, we do not need to call sctp_transport_walk_stop any more.
For sctp proc, we will use 'iter->start_fail' to decide if we will call
rhashtable_walk_stop/exit.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In sctp proc, these three functions in remaddrs and assocs are the
same. we should merge them into one.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This one will implement all the interface of inet_diag, inet_diag_handler.
which includes sctp_diag_dump, sctp_diag_dump_one and sctp_diag_get_info.
It will work as a module, and register inet_diag_handler when loading.
v2->v3:
- fix the mistake in inet_assoc_attr_size().
- change inet_diag_msg_laddrs_fill() name to inet_diag_msg_sctpladdrs_fill.
- change inet_diag_msg_paddrs_fill() name to inet_diag_msg_sctpaddrs_fill.
- add inet_diag_msg_sctpinfo_fill() to make asoc/ep fill code clearer.
- add inet_diag_msg_sctpasoc_fill() to make asoc fill code clearer.
- merge inet_asoc_diag_fill() and inet_ep_diag_fill() to
inet_sctp_diag_fill().
- call sctp_diag_get_info() directly, instead by handler, cause the caller
is in the same file with it.
- call lock_sock in sctp_tsp_dump_one() to make sure we call get sctp info
safely.
- after lock_sock(sk), we should check sk != assoc->base.sk.
- change mem[SK_MEMINFO_WMEM_ALLOC] to asoc->sndbuf_used for asoc dump when
asoc->ep->sndbuf_policy is set. don't use INET_DIAG_MEMINFO attr any more.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
inet_diag_msg_common_fill is used to fill the diag msg common info,
we need to use it in sctp_diag as well, so export it.
inet_diag_msg_attrs_fill is used to fill some common attrs info between
sctp diag and tcp diag.
v2->v3:
- do not need to define and export inet_diag_get_handler any more.
cause all the functions in it are in sctp_diag.ko, we just call
them in sctp_diag.ko.
- add inet_diag_msg_attrs_fill to make codes clear.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For some main variables in sctp.ko, we couldn't export it to other modules,
so we have to define some api to access them.
It will include sctp transport and endpoint's traversal.
There are some transport traversal functions for sctp_diag, we can also
use it for sctp_proc. cause they have the similar situation to traversal
transport.
v2->v3:
- rhashtable_walk_init need the parameter gfp, because of recent upstrem
update
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
sctp_diag will dump some important details of sctp's assoc or ep, we use
sctp_info to describe them, sctp_get_sctp_info to get them, and export
it to sctp_diag.ko.
v2->v3:
- we will not use list_for_each_safe in sctp_get_sctp_info, cause
all the callers of it will use lock_sock.
- fix the holes in struct sctp_info with __reserved* field.
because sctp_diag is a new feature, and sctp_info is just for now,
it may be changed in the future.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adding a 2nd PHY to cpsw results in a NULL pointer dereference
as below. Fix by maintaining a reference to each PHY node in slave
struct instead of a single reference in the priv struct which was
overwritten by the 2nd PHY.
[ 17.870933] Unable to handle kernel NULL pointer dereference at virtual address 00000180
[ 17.879557] pgd = dc8bc000
[ 17.882514] [00000180] *pgd=9c882831, *pte=00000000, *ppte=00000000
[ 17.889213] Internal error: Oops: 17 [#1] ARM
[ 17.893838] Modules linked in:
[ 17.897102] CPU: 0 PID: 1657 Comm: connmand Not tainted 4.5.0-ge463dfb-dirty #11
[ 17.904947] Hardware name: Cambrionix whippet
[ 17.909576] task: dc859240 ti: dc968000 task.ti: dc968000
[ 17.915339] PC is at phy_attached_print+0x18/0x8c
[ 17.920339] LR is at phy_attached_info+0x14/0x18
[ 17.925247] pc : [<c042baec>] lr : [<c042bb74>] psr: 600f0113
[ 17.925247] sp : dc969cf8 ip : dc969d28 fp : dc969d18
[ 17.937425] r10: dda7a400 r9 : 00000000 r8 : 00000000
[ 17.942971] r7 : 00000001 r6 : ddb00480 r5 : ddb8cb34 r4 : 00000000
[ 17.949898] r3 : c0954cc0 r2 : c09562b0 r1 : 00000000 r0 : 00000000
[ 17.956829] Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none
[ 17.964401] Control: 10c5387d Table: 9c8bc019 DAC: 00000051
[ 17.970500] Process connmand (pid: 1657, stack limit = 0xdc968210)
[ 17.977059] Stack: (0xdc969cf8 to 0xdc96a000)
[ 17.981692] 9ce0: dc969d28 dc969d08
[ 17.990386] 9d00: c038f9bc c038f6b4 ddb00480 dc969d34 dc969d28 c042bb74 c042bae4 00000000
[ 17.999080] 9d20: c09562b0 c0954cc0 dc969d5c dc969d38 c043ebfc c042bb6c 00000007 00000003
[ 18.007773] 9d40: ddb00000 ddb8cb58 ddb00480 00000001 dc969dec dc969d60 c0441614 c043ea68
[ 18.016465] 9d60: 00000000 00000003 00000000 fffffff4 dc969df4 0000000d 00000000 00000000
[ 18.025159] 9d80: dc969db4 dc969d90 c005dc08 c05839e0 dc969df4 0000000d ddb00000 00001002
[ 18.033851] 9da0: 00000000 00000000 dc969dcc dc969db8 c005ddf4 c005dbc8 00000000 00000118
[ 18.042544] 9dc0: dc969dec dc969dd0 ddb00000 c06db27c ffff9003 00001002 00000000 00000000
[ 18.051237] 9de0: dc969e0c dc969df0 c057c88c c04410dc dc969e0c ddb00000 ddb00000 00000001
[ 18.059930] 9e00: dc969e34 dc969e10 c057cb44 c057c7d8 ddb00000 ddb00138 00001002 beaeda20
[ 18.068622] 9e20: 00000000 00000000 dc969e5c dc969e38 c057cc28 c057cac0 00000000 dc969e80
[ 18.077315] 9e40: dda7a40c beaeda20 00000000 00000000 dc969ecc dc969e60 c05e36d0 c057cc14
[ 18.086007] 9e60: dc969e84 00000051 beaeda20 00000000 dda7a40c 00000014 ddb00000 00008914
[ 18.094699] 9e80: 30687465 00000000 00000000 00000000 00009003 00000000 00000000 00000000
[ 18.103391] 9ea0: 00001002 00008914 dd257ae0 beaeda20 c098a428 beaeda20 00000011 00000000
[ 18.112084] 9ec0: dc969edc dc969ed0 c05e4e54 c05e3030 dc969efc dc969ee0 c055f5ac c05e4cc4
[ 18.120777] 9ee0: beaeda20 dd257ae0 dc8ab4c0 00008914 dc969f7c dc969f00 c010b388 c055f45c
[ 18.129471] 9f00: c071ca40 dd257ac0 c00165e8 dc968000 dc969f3c dc969f20 dc969f64 dc969f28
[ 18.138164] 9f20: c0115708 c0683ec8 dd257ac0 dd257ac0 dc969f74 dc969f40 c055f350 c00fc66c
[ 18.146857] 9f40: dd82e4d0 00000011 00000000 00080000 dd257ac0 00000000 dc8ab4c0 dc8ab4c0
[ 18.155550] 9f60: 00008914 beaeda20 00000011 00000000 dc969fa4 dc969f80 c010bc34 c010b2fc
[ 18.164242] 9f80: 00000000 00000011 00000002 00000036 c00165e8 dc968000 00000000 dc969fa8
[ 18.172935] 9fa0: c00163e0 c010bbcc 00000000 00000011 00000011 00008914 beaeda20 00009003
[ 18.181628] 9fc0: 00000000 00000011 00000002 00000036 00081018 00000001 00000000 beaedc10
[ 18.190320] 9fe0: 00083188 beaeda1c 00043a5d b6d29c0c 600b0010 00000011 00000000 00000000
[ 18.198989] Backtrace:
[ 18.201621] [<c042bad8>] (phy_attached_print) from [<c042bb74>] (phy_attached_info+0x14/0x18)
[ 18.210664] r3:c0954cc0 r2:c09562b0 r1:00000000
[ 18.215588] r4:ddb00480
[ 18.218322] [<c042bb60>] (phy_attached_info) from [<c043ebfc>] (cpsw_slave_open+0x1a0/0x280)
[ 18.227293] [<c043ea5c>] (cpsw_slave_open) from [<c0441614>] (cpsw_ndo_open+0x544/0x674)
[ 18.235874] r7:00000001 r6:ddb00480 r5:ddb8cb58 r4:ddb00000
[ 18.241944] [<c04410d0>] (cpsw_ndo_open) from [<c057c88c>] (__dev_open+0xc0/0x128)
[ 18.249972] r9:00000000 r8:00000000 r7:00001002 r6:ffff9003 r5:c06db27c r4:ddb00000
[ 18.258255] [<c057c7cc>] (__dev_open) from [<c057cb44>] (__dev_change_flags+0x90/0x154)
[ 18.266745] r5:00000001 r4:ddb00000
[ 18.270575] [<c057cab4>] (__dev_change_flags) from [<c057cc28>] (dev_change_flags+0x20/0x50)
[ 18.279523] r9:00000000 r8:00000000 r7:beaeda20 r6:00001002 r5:ddb00138 r4:ddb00000
[ 18.287811] [<c057cc08>] (dev_change_flags) from [<c05e36d0>] (devinet_ioctl+0x6ac/0x76c)
[ 18.296483] r9:00000000 r8:00000000 r7:beaeda20 r6:dda7a40c r5:dc969e80 r4:00000000
[ 18.304762] [<c05e3024>] (devinet_ioctl) from [<c05e4e54>] (inet_ioctl+0x19c/0x1c8)
[ 18.312882] r10:00000000 r9:00000011 r8:beaeda20 r7:c098a428 r6:beaeda20 r5:dd257ae0
[ 18.321235] r4:00008914
[ 18.323956] [<c05e4cb8>] (inet_ioctl) from [<c055f5ac>] (sock_ioctl+0x15c/0x2d8)
[ 18.331829] [<c055f450>] (sock_ioctl) from [<c010b388>] (do_vfs_ioctl+0x98/0x8d0)
[ 18.339765] r7:00008914 r6:dc8ab4c0 r5:dd257ae0 r4:beaeda20
[ 18.345822] [<c010b2f0>] (do_vfs_ioctl) from [<c010bc34>] (SyS_ioctl+0x74/0x84)
[ 18.353573] r10:00000000 r9:00000011 r8:beaeda20 r7:00008914 r6:dc8ab4c0 r5:dc8ab4c0
[ 18.361924] r4:00000000
[ 18.364653] [<c010bbc0>] (SyS_ioctl) from [<c00163e0>] (ret_fast_syscall+0x0/0x3c)
[ 18.372682] r9:dc968000 r8:c00165e8 r7:00000036 r6:00000002 r5:00000011 r4:00000000
[ 18.380960] Code: e92dd810 e24cb010 e24dd010 e59b4004 (e5902180)
[ 18.387580] ---[ end trace c80529466223f3f3 ]---
Signed-off-by: Andrew Goodbody <andrew.goodbody@cambrionix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
SCTP already serializes access to rcvbuf through its sock lock:
sctp_recvmsg takes it right in the start and release at the end, while
rx path will also take the lock before doing any socket processing. On
sctp_rcv() it will check if there is an user using the socket and, if
there is, it will queue incoming packets to the backlog. The backlog
processing will do the same. Even timers will do such check and
re-schedule if an user is using the socket.
Simplifying this will allow us to remove sctp_skb_list_tail and get ride
of some expensive lockings. The lists that it is used on are also
mangled with functions like __skb_queue_tail and __skb_unlink in the
same context, like on sctp_ulpq_tail_event() and sctp_clear_pd().
sctp_close() will also purge those while using only the sock lock.
Therefore the lockings performed by sctp_skb_list_tail() are not
necessary. This patch removes this function and replaces its calls with
just skb_queue_splice_tail_init() instead.
The biggest gain is at sctp_ulpq_tail_event(), because the events always
contain a list, even if it's queueing a single skb and this was
triggering expensive calls to spin_lock_irqsave/_irqrestore for every
data chunk received.
As SCTP will deliver each data chunk on a corresponding recvmsg, the
more effective the change will be.
Before this patch, with chunks with 30 bytes:
netperf -t SCTP_STREAM -H 192.168.1.2 -cC -l 60 -- -m 30 -S 400000
400000 -s 400000 400000
on a 10Gbit link with 1500 MTU:
SCTP STREAM TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 192.168.1.1 () port 0 AF_INET
Recv Send Send Utilization Service Demand
Socket Socket Message Elapsed Send Recv Send Recv
Size Size Size Time Throughput local remote local remote
bytes bytes bytes secs. 10^6bits/s % S % S us/KB us/KB
425984 425984 30 60.00 137.45 7.34 7.36 52.504 52.608
With it:
SCTP STREAM TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 192.168.1.1 () port 0 AF_INET
Recv Send Send Utilization Service Demand
Socket Socket Message Elapsed Send Recv Send Recv
Size Size Size Time Throughput local remote local remote
bytes bytes bytes secs. 10^6bits/s % S % S us/KB us/KB
425984 425984 30 60.00 179.10 7.97 6.70 43.740 36.788
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Saeed Mahameed says:
====================
mlx5_core: mlx5_ifc updates
This series include mlx5_core updates for both net-next and rdma
trees for 4.7 kernel cycle. This is the only shared code planned
for 4.7 between rdma and net trees. Hopefully, this will prevent
future conflicts when merging between ib-next and net-next once
4.7 cycle is over and merge window is opened.
Both Mellanox rdma and net submissions will proceed once this series
is applied into both trees.
Future shared code will be sent to both maintainers as pull requests
from Mellanox's kernel.org tree.
We have included all the maintainers of respective drivers.
Kindly review the change and let us know in case of any review comments.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adding the needed mlx5_ifc hardware bits and structs
for the following feature:
* Add vport to steering commands for SRIOV ACL support
* Add mlcr, pcmr and mcia registers for dump module EEPROM
* Add support for FCS, baeacon led and disable_link bits to
hca caps
* Add CQE period mode bit in CQ context for CQE based CQ
moderation support
* Add umr SQ bit for fragmented memory registration
* Add needed bits and caps for Striding RQ support
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
All reserved fields after early_vf_enable are off by 1, since
early_vf_enable was not explicitly declared as array of size 1.
Reserved field before cqe_zip had a wrong size, it should
be 0x80 + 0x3f.
Fixes: b0844444590e ("net/mlx5_core: Introduce access function to read internal timer ")
Fixes: b4ff3a36d3e4 ("net/mlx5: Use offset based reserved field names in the IFC header file")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Manish Chopra says:
====================
qed/qede: Add tunneling support
This patch series adds support for VXLAN, GRE and GENEVE tunnels
to be used over this driver. With this support, adapter can perform
TSO offload, inner/outer checksums offloads on TX and RX for
encapsulated packets.
V1->V2 [ Comments from Jesse Gross incorporated ]
* Drop general infrastructure change patch.
"net: Make vxlan/geneve default udp ports public"
* Remove by default Linux default UDP ports configurations in driver.
Instead, use general registration APIs for UDP port configurations
* Removing .ndo_features_check - we will add it later with proper change.
Please consider applying this series to net-next.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch enables netdev tunneling features and adds
TX/RX fastpath support for tunneling in driver.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch enables GENEVE tunnel on the adapter and
add support for driver hooks to configure UDP ports
for GENEVE tunnel offload to be performed by the adapter.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch enables VXLAN tunnel on the adapter and
add support for driver hooks to configure UDP ports
for VXLAN tunnel offload to be performed by the adapter.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds various structure/APIs needed to configure/enable different
tunnel [VXLAN/GRE/GENEVE] parameters on the adapter.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds support for the newer version 1 of the HSR
networking standard. Version 0 is still default and the new
version has to be selected via iproute2.
Main changes are in the supervision frame handling and its
ethertype field.
Signed-off-by: Peter Heise <peter.heise@airbus.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ACPI specification does not specify the state of data after a clear
poison operation. Potential future libnvdimm bus implementations for
other architectures also might not specify or disagree on the state of
data after clear poison. Clarify why we write twice.
Reported-by: Jeff Moyer <jmoyer@redhat.com>
Reported-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Reviewed-by: Vishal Verma <vishal.l.verma@intel.com>
|
|
Eric Dumazet says:
====================
tcp: final work on SYNFLOOD behavior
In the first patch, I remove the costly association of SYNACK+COOKIES
to a listener. I believe other parts of the stack should be ready.
The second patch removes a useless write into listener socket
in tcp_rcv_state_process(), incurring false sharing in
tcp_conn_request()
Performance under SYNFLOOD goes from 3.2 Mpps to 6 Mpps.
Test was using a single TCP listener, on a host with 8 RX queues
on the NIC, and 24 cores (48 ht)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Last known hot point during SYNFLOOD attack is the clearing
of rx_opt.saw_tstamp in tcp_rcv_state_process()
It is not needed for a listener, so we move it where it matters.
Performance while a SYNFLOOD hits a single listener socket
went from 5 Mpps to 6 Mpps on my test server (24 cores, 8 NIC RX queues)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When removing sk_refcnt manipulation on synflood, I missed that
using skb_set_owner_w() was racy, if sk->sk_wmem_alloc had already
transitioned to 0.
We should hold sk_refcnt instead, but this is a big deal under attack.
(Doing so increase performance from 3.2 Mpps to 3.8 Mpps only)
In this patch, I chose to not attach a socket to syncookies skb.
Performance is now 5 Mpps instead of 3.2 Mpps.
Following patch will remove last known false sharing in
tcp_rcv_state_process()
Fixes: 3b24d854cb35 ("tcp/dccp: do not touch listener sk_refcnt under synflood")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace deprecated create_singlethread_workqueue with
alloc_ordered_workqueue.
Work items include getting tx/rx frame sizes, resetting MPI processor,
setting asic recovery bit so ordering seems necessary as only one work
item should be in queue/executing at any given time, hence the use of
alloc_ordered_workqueue.
WQ_MEM_RECLAIM flag has been set since ethernet devices seem to sit in
memory reclaim path, so to guarantee forward progress regardless of
memory pressure.
Signed-off-by: Amitoj Kaur Chawla <amitoj1606@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Jon Maloy says:
====================
tipc: improvements to the link setup algorithm
This series addresses some smaller issues regarding the link setup
algorithm. The first commit fixes a rare bug we have discovered during
testing; the second one may have some future impact on cluster
scalabilty, while remaining ones can be regarded as cosmetic in
a wider sense of the word.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
According to the link FSM, a received traffic packet can take a link
from state ESTABLISHING to ESTABLISHED, but the link can still not be
fully set up in one atomic operation. This means that even if the the
very first packet on the link is a traffic packet with sequence number
1 (one), it has to be dropped and retransmitted.
This can be avoided if we let the mentioned packet be preceded by a
LINK_PROTOCOL/STATE message, which takes up the endpoint before the
arrival of the traffic.
We add this small feature in this commit.
This is a fully compatible change.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In some link establishment scenarios we see that packet #2 may be sent
out before packet #1, forcing the receiver to demand retransmission of
the missing packet. This is harmless, but may cause confusion among
people tracing the packet flow.
Since this is extremely easy to fix, we do so by adding en extra send
call to the bearer immediately after the link has come up.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The function tipc_link_timeout() is unnecessary complex, and can
easily be made more readable.
We do that with this commit. The only functional change is that we
remove a redundant test for whether the broadcast link is up or not.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When a link is down, it will continuously try to re-establish contact
with the peer by sending out a RESET or an ACTIVATE message at each
timeout interval. The default value for this interval is currently
375 ms. This is wasteful, and may become a problem in very large
clusters with dozens or hundreds of nodes being down simultaneously.
We now introduce a simple backoff algorithm for these cases. The
first five messages are sent at default rate; thereafter a message
is sent only each 16th timer interval.
This will cover the vast majority of link recycling cases, since the
endpoint starting last will transmit at the higher speed, and the link
should normally be established well be before the rate needs to be
reduced.
The only case where we will see a degradation of link re-establishment
times is when the endpoints remain intact, and a glitch in the
transmission media is causing the link reset. We will then experience
a worst-case re-establishing time of 6 seconds, something we deem
acceptable.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When a link endpoint is going down locally, e.g., because its interface
is being stopped, it will spontaneously send out a RESET message to
its peer, informing it about this fact. This saves the peer from
detecting the failure via probing, and hence gives both speedier and
less resource consuming failure detection on the peer side.
According to the link FSM, a receiver of a RESET message, ignoring the
reason for it, must now consider the sender ready to come back up, and
starts periodically sending out ACTIVATE messages to the peer in order
to re-establish the link. Also, according to the FSM, the receiver of
an ACTIVATE message can now go directly to state ESTABLISHED and start
sending regular traffic packets. This is a well-proven and robust FSM.
However, in the case of a reboot, there is a small possibilty that link
endpoint on the rebooted node may have been re-created with a new bearer
identity between the moment it sent its (pre-boot) RESET and the moment
it receives the ACTIVATE from the peer. The new bearer identity cannot
be known by the peer according to this scenario, since traffic headers
don't convey such information. This is a problem, because both endpoints
need to know the correct value of the peer's bearer id at any moment in
time in order to be able to produce correct link events for their users.
The only way to guarantee this is to enforce a full setup message
exchange (RESET + ACTIVATE) even after the reboot, since those messages
carry the bearer idientity in their header.
In this commit we do this by introducing and setting a "stopping" bit in
the header of the spontaneously generated RESET messages, informing the
peer that the sender will not be immediately ready to re-establish the
link. A receiver seeing this bit must act as if this were a locally
detected connectivity failure, and hence has to go through a full two-
way setup message exchange before any link can be re-established.
Although never reported, this problem seems to have always been around.
This protocol addition is fully backwards compatible.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Chelsio adapters have two VPD structures stored in the VPD:
- offset 0x000: an abbreviated VPD, and
- offset 0x400: the complete VPD.
After 104daa71b396 ("PCI: Determine actual VPD size on first access"), the
PCI core computes the valid VPD size by parsing the VPD starting at offset
0x0. That size only includes the abbreviated VPD structure, so reads of
the complete VPD at 0x400 fail.
Explicitly set the VPD size with pci_set_vpd_size() so the driver can read
both VPD structures.
[bhelgaas: changelog, split patches, rename to pci_set_vpd_size() and
return int (not ssize_t)]
Fixes: 104daa71b396 ("PCI: Determine actual VPD size on first access")
Tested-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
After 104daa71b396 ("PCI: Determine actual VPD size on first access"), the
PCI core computes the valid VPD size by parsing the VPD starting at offset
0x0. We don't attempt to read past that valid size because that causes
some devices to crash.
However, some devices do have data past that valid size. For example,
Chelsio adapters contain two VPD structures, and the driver needs both of
them.
Add pci_set_vpd_size(). If a driver knows it is safe to read past the end
of the VPD data structure at offset 0, it can use pci_set_vpd_size() to
allow access to as much data as it needs.
[bhelgaas: changelog, split patches, rename to pci_set_vpd_size() and
return int (not ssize_t)]
Fixes: 104daa71b396 ("PCI: Determine actual VPD size on first access")
Tested-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Jiri Pirko says:
====================
mlxsw: spectrum_buffers: couple of cosmetic patches
As suggested by David Laight
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Suggested-by: David Laight <David.Laight@ACULAB.COM>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
