summaryrefslogtreecommitdiff
AgeCommit message (Collapse)AuthorFilesLines
2015-08-05ARM: dts: lpc4350-hitex-eval: add ethernetAriel D'Alessandro1-0/+60
Enable Ethernet and add pin muxing and set the correct frequency on the enet tx clock input. Signed-off-by: Ariel D'Alessandro <ariel@vanguardiasur.com.ar> Signed-off-by: Joachim Eastwood <manabian@gmail.com> Signed-off-by: Olof Johansson <olof@lixom.net>
2015-08-05ARM: dts: lpc4350-hitex-eval: add pinctrl and uart0 muxingAriel D'Alessandro1-0/+20
Setup pin muxing and properties for the debug console on uart0. Signed-off-by: Ariel D'Alessandro <ariel@vanguardiasur.com.ar> Signed-off-by: Joachim Eastwood <manabian@gmail.com> Signed-off-by: Olof Johansson <olof@lixom.net>
2015-08-05ARM: dts: lpc4357-ea4357: add mmio-gpio ledsJoachim Eastwood1-0/+69
Hook up LEDs on the outputs from the D-type flip-flop found on the address/data bus. Note that the LEDx label in the schematics is reversed in regard to the bits on the data bus. Hence the reverse ordering used here. Signed-off-by: Joachim Eastwood <manabian@gmail.com> Signed-off-by: Olof Johansson <olof@lixom.net>
2015-08-05ARM: dts: lpc4357-ea4357: add emc pins and static memory devicesJoachim Eastwood1-0/+164
Setup the emc pins used by external memory devices and add configuration for the devices found on the EA4357 devkit. The EA4357 devkit has a NOR Flash attached to chip select 0 and a D-type flip-flop used for LEDs on chip select 2. Signed-off-by: Joachim Eastwood <manabian@gmail.com> Signed-off-by: Olof Johansson <olof@lixom.net>
2015-08-05ARM: dts: lpc4357-ea4357: add usb0Joachim Eastwood1-0/+20
Enable USB0 on the EA4357 devkit and setup the required USB0 control pins. Signed-off-by: Joachim Eastwood <manabian@gmail.com> Signed-off-by: Olof Johansson <olof@lixom.net>
2015-08-05ARM: dts: lpc18xx: add pl172 memory-controller nodeJoachim Eastwood1-0/+14
All devices in the LPC18xx/43xx familiy contain a ARM PL172 MultiPort Memory Controller (MPMC). Signed-off-by: Joachim Eastwood <manabian@gmail.com> Signed-off-by: Olof Johansson <olof@lixom.net>
2015-08-05ARM: dts: lpc18xx: add pl111 lcd controller nodeJoachim Eastwood1-0/+10
NXP LPC185x and LPC435x/70 devices contain a ARM PL111 lcd controller. Signed-off-by: Joachim Eastwood <joachim.eastwood@gmail.com> Signed-off-by: Olof Johansson <olof@lixom.net>
2015-08-05ARM: dts: lpc18xx: add usb otg phy nodeJoachim Eastwood1-0/+8
Add the USB OTG phy under the CREG syscon node and attach it to the USB0 EHCI controller. Signed-off-by: Joachim Eastwood <manabian@gmail.com> Signed-off-by: Olof Johansson <olof@lixom.net>
2015-08-05Merge tag 'mvebu-dt-4.3-2' of git://git.infradead.org/linux-mvebu into next/dtOlof Johansson2-0/+274
mvebu dt changes for v4.3 (part #2) Add support Buffalo Linkstation LS-WTGL * tag 'mvebu-dt-4.3-2' of git://git.infradead.org/linux-mvebu: ARM: dts: orion5x: add buffalo linkstation ls-wtgl Signed-off-by: Olof Johansson <olof@lixom.net>
2015-08-05Merge tag 'zynq-dt-for-4.3' of https://github.com/Xilinx/linux-xlnx into next/dtOlof Johansson3-1/+34
arm: Xilinx Zynq dt patches for v4.3 - Add ECC for Synopsys MC - Add OCM, pushbuttons to zc702 * tag 'zynq-dt-for-4.3' of https://github.com/Xilinx/linux-xlnx: ARM: zynq: DT: Add zc702 pushbuttons to DT as gpio-keys ARM: zynq: DT: Add missing interrupt for L2 pl310 Documentation: devicetree: Add ECC information to synopsys ddr controller ARM: dts: zynq: Add OCM node Signed-off-by: Olof Johansson <olof@lixom.net>
2015-08-05Merge tag 'qcom-dt-for-4.3' of git://codeaurora.org/quic/kernel/agross-msm ↵Olof Johansson7-22/+523
into next/dt Qualcomm ARM Based Device Tree Updates for v4.3 * Switch to use pinctrl compatible for GPIOs * Add RPM regulators for MSM8960 * Add SPI Ethernet support on MSM8960 CDP * Add SMEM support along with dependencies * Add PM8921 support for GPIO and MPP * Fix GSBI cell index * Switch to use real regulators on APQ8064 w/ SDCC * tag 'qcom-dt-for-4.3' of git://codeaurora.org/quic/kernel/agross-msm: ARM: dts: qs600: Add real regulators to sdcc ARM: dts: ifc6410: add real regulators for sdcc nodes. ARM: dts: apq8064: remove temporary fixed regulator for mmc ARM: dts: apq8064: fix missing gsbi cell-index ARM: dts: apq8064: Add DT support for GSBI6 and for UART pin mux ARM: dts: apq8064: add pm8921 mpp support ARM: dts: apq8064: Add pm8921 mfd and its gpio node ARM: dts: msm8974: Add smem reservation and node ARM: dts: msm8974: Add tcsr mutex node ARM: dts: qcom: Add ks8851 node for wired ethernet ARM: dts: qcom: Add MSM8960 CDP RPM regulators ARM: dts: qcom: Add MSM8960 RPM and RPM regulator nodes ARM: dts: qcom: Replace gpio node with pinctrl node ARM: dts: qcom: Replace gpio node with pinctrl node Signed-off-by: Olof Johansson <olof@lixom.net>
2015-08-05Merge tag 'at91-dt' of ↵Olof Johansson9-31/+1157
git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91 into next/dt First batch of DT changes for 4.3: - some fixes on sama5d4 ADC definition - adding Image Sensor Interface (aka ISI) on at91sam9m10g45ek board - update rst controller compatible string on sama5 machines - new sama5d2 DT definition and its reference board: the sama5d2 Xplained. Minimal configuration for now. * tag 'at91-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91: ARM: at91/dt: add minimal sama5d2 Xplained board ARM: at91/dt: add basic dtsi for sama5d2 SoC ARM: at91/dt: sama5: update rstc to correct compatible string ARM: at91/dt: add isi & ov2640 dt nodes for at91sam9m10g45ek board ARM: at91/dt: sama5d4: move ADC pinctrl to board device trees ARM: at91/dt: sama5d4: fix external trigger property Signed-off-by: Olof Johansson <olof@lixom.net>
2015-07-31ARM: zynq: DT: Add zc702 pushbuttons to DT as gpio-keysEzra Savard1-0/+21
Adds the two MIO connected pushbuttons on the zc702 board to the devicetree as a single multi-key device for us with the gpio-keys driver. Signed-off-by: Ezra Savard <ezra.savard@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2015-07-31ARM: zynq: DT: Add missing interrupt for L2 pl310Alex Wilson1-0/+1
Add pl310 interrupt to the Zynq devicetree. Signed-off-by: Alex Wilson <alex.david.wilson@gmail.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2015-07-31Documentation: devicetree: Add ECC information to synopsys ddr controllerPunnaiah Choudary Kalluri1-0/+4
Add ECC information to synopsys ddr memory controller. Signed-off-by: Punnaiah Choudary Kalluri <punnaia@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2015-07-31ARM: dts: zynq: Add OCM nodeMichal Simek2-1/+8
Add OCM node for all zynq boards. OCM location can changed but for all current boards this is the location where OCM is.` Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2015-07-30ARM: at91/dt: add minimal sama5d2 Xplained boardNicolas Ferre2-0/+135
Add minimal support for the new sama5d2 Xplained board. Only USB, spi/i2c, ethernet and uart/usart peripherals added. With this DTS file you can boot the board and begin to play with it. Rootfs on NFS and sd card have successfully been tested. Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2015-07-30ARM: at91/dt: add basic dtsi for sama5d2 SoCLudovic Desroches1-0/+925
Only the basic support for this new Atmel Cortex-A5 SoC. A subset of the peripherals is setup to allow booting. IRQ, clocks, USB, crypto, timers, rtc, ethernet, spi/i2c and uart/usart peripheral nodes are added. Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com> Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
2015-07-30ARM: at91/dt: sama5: update rstc to correct compatible stringJosh Wu2-2/+2
They'll use "atmel,sama5d3-rstc" for reset function. Signed-off-by: Josh Wu <josh.wu@atmel.com> Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> [nicolas.ferre@atmel.com: add the old compatible string as a fallback] Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
2015-07-30ARM: at91/dt: add isi & ov2640 dt nodes for at91sam9m10g45ek boardJosh Wu2-19/+76
First we group the isi data pins, and for now we only use 0~7 data pins with HSYNC and VSYNC. Also add the link for atmel-isi and ov2640 sensor node. Signed-off-by: Josh Wu <josh.wu@atmel.com> [nicolas.ferre@atmel.com: move the pinctrl properties in board .dts file] Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
2015-07-28ARM: dts: qs600: Add real regulators to sdccSrinivas Kandagatla1-0/+20
This patch adds real regulators to sdcc nodes. Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Signed-off-by: Andy Gross <agross@codeaurora.org>
2015-07-28ARM: dts: ifc6410: add real regulators for sdcc nodes.Srinivas Kandagatla1-0/+27
This patch adds real regulators for all the three sdcc nodes. Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Signed-off-by: Andy Gross <agross@codeaurora.org>
2015-07-28ARM: dts: apq8064: remove temporary fixed regulator for mmcSrinivas Kandagatla1-12/+0
This patch removes temporary fixed regluator use for mmc. Board files should use the regulators which are wiredup appropriately. Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Signed-off-by: Andy Gross <agross@codeaurora.org>
2015-07-28Merge tag 'socfpga_dts_for_v4.3' of ↵Olof Johansson8-11/+163
git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux into next/dt SoCFPGA DTS updates for v4.3 - Update clocking for DTS nodes - Add DTS board file for Terasic DE0 Atlas board - Use stdout-patch for chosen node - Enable prefetch-data and prefetch-instr * tag 'socfpga_dts_for_v4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux: ARM: socfpga: dts: add osc1 as a possible parent for dbg_base_clk ARM: socfpga: dts: add missing clock gates to socfpga.dtsi ARM: socfpga: dts: Fix gpio dts entry for the correct clock ARM: socfpga: dts: Correct the parent clock for l3_sp_clk and dbg_clk ARM: dts: socfpga: Add support of Terasic DE0 Atlas board ARM: dts: socfpga: use stdout-path for chosen node ARM: dts: socfpga: enable the data and instruction prefetch for the l2 cache Signed-off-by: Olof Johansson <olof@lixom.net>
2015-07-28Merge tag 'v4.2-next-dts' of https://github.com/mbgg/linux-mediatek into next/dtOlof Johansson9-9/+411
- ARM: dts: mediatek: add mt6580 basic support - Document: DT: Add bindings for mediatek MT6580 SoC Platform - ARM: dts: mediatek mt8135: Use real UART clocks - ARM: dts: mt8135-evbp1: Add PMIC support - ARM: dts: mt8135: Add pmic wrapper nodes - ARM: dts: mediatek: Enable clock support for Mediatek MT8135. * tag 'v4.2-next-dts' of https://github.com/mbgg/linux-mediatek: ARM: dts: mediatek: add mt6580 basic support Document: DT: Add bindings for mediatek MT6580 SoC Platform ARM: dts: mediatek mt8135: Use real UART clocks ARM: dts: mt8135-evbp1: Add PMIC support ARM: dts: mt8135: Add pmic wrapper nodes ARM: dts: mediatek: Enable clock support for Mediatek MT8135. Signed-off-by: Olof Johansson <olof@lixom.net>
2015-07-28ARM: at91/dt: sama5d4: move ADC pinctrl to board device treesAlexandre Belloni3-9/+18
The ADC pinctrl is board specific, move it to the board device trees. Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
2015-07-28ARM: at91/dt: sama5d4: fix external trigger propertyAlexandre Belloni1-1/+1
The property is actually atmel,adc-use-external-triggers. Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
2015-07-28ARM: dts: apq8064: fix missing gsbi cell-indexSrinivas Kandagatla1-0/+1
Without this i2c instance for missing cell-index nodes would fail, fix it by adding correct cell-index. Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Signed-off-by: Andy Gross <agross@codeaurora.org>
2015-07-28ARM: dts: apq8064: Add DT support for GSBI6 and for UART pin muxPramod Gurav2-1/+42
This change adds DT support for GSBI6 and muxes the gpio pins as UART lines. Also defines a alias for serial port on these lines. Signed-off-by: Pramod Gurav <pramod.gurav@smartplayin.com> [Srinivas Kandagatla]: fix pinctrl location and rename alias correctly Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Signed-off-by: Andy Gross <agross@codeaurora.org>
2015-07-28ARM: dts: apq8064: add pm8921 mpp supportSrinivas Kandagatla1-0/+12
This patch adds pmic pm8921 mpp gpio controller node. Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Signed-off-by: Andy Gross <agross@codeaurora.org>
2015-07-28ARM: dts: apq8064: Add pm8921 mfd and its gpio nodeSrinivas Kandagatla1-1/+35
This patch adds pmic gpio node to the device tree, this node is necessary for devices like wlan to control reset gpio. Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Signed-off-by: Andy Gross <agross@codeaurora.org>
2015-07-27ARM: dts: UniPhier: add UART and USB pinmux nodesMasahiro Yamada4-0/+131
The DT nodes in uniphier-pinctrl.dtsi provide the default pinctrl settings that would be suitable for most boards. You can still override them in your board DTS file if necessary. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: Olof Johansson <olof@lixom.net>
2015-07-27ARM: dts: UniPhier: add pinctrl device nodesMasahiro Yamada3-0/+18
Add the pinctrol device nodes for UniPhier PH1-LD4, PH1-Pro4, and PH1-sLD8. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: Olof Johansson <olof@lixom.net>
2015-07-27Merge tag 'omap-for-v4.3/dt-dm814x' of ↵Olof Johansson6-0/+529
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt omap dts changes for minimal dm814x support for v4.3 merge window. These changes make dm814x boot and adds minimal board support for dm814x-evm and hp t410. Note that to boot these depend on omap-for-v4.3/soc-signed branch, but as dm814x support is currently broken, these can be merged separately with the other dts changes. * tag 'omap-for-v4.3/dt-dm814x' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: ARM: OMAP2+: Add custom abort handler for t410 ARM: dts: Add minimal support for HP T410 ARM: dts: Add minimal dts support for dm8148-evm ARM: dts: Add minimal clocks for dm814x ARM: dts: Add minimal dm814x support Signed-off-by: Olof Johansson <olof@lixom.net>
2015-07-27Merge tag 'renesas-dt2-for-v4.3' of ↵Olof Johansson8-3/+109
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt Second Round of Renesas ARM Based SoC DT Updates for v4.3 * Add Audio MIX and CTU support to r8a779[01] SoCs * Correct IRQ sense for adv7511 on lager board * Add sound label to koelsch and lager boards * Add IIC support to emev2 SoC * tag 'renesas-dt2-for-v4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: ARM: shmobile: r8a7791: Add Audio MIX support on DTSI ARM: shmobile: r8a7791: Add Audio CTU support on DTSI ARM: shmobile: r8a7790: Add Audio MIX support on DTSI ARM: shmobile: r8a7790: Add Audio CTU support on DTSI ARM: shmobile: lager: Fix adv7511 IRQ sensing ARM: shmobile: koelsch: add sound label on DTS ARM: shmobile: lager: add sound label on DTS ARM: shmobile: emev2: kzm9d: enable IIC busses ARM: shmobile: emev2: add IIC cores to dtsi Signed-off-by: Olof Johansson <olof@lixom.net>
2015-07-27Merge tag 'stm32-dt-for-v4.3-1b' of ↵Olof Johansson4-58/+108
https://git.kernel.org/pub/scm/linux/kernel/git/mcoquelin/stm32 into next/dt STM32 DT updates for v4.3, round 1. Highlights: ----------- - Add RCC clocks support to STM32F429 - Add STM32429i-EVAL board support - Use stdout-path instead of linux,stdout-path in Disco board * tag 'stm32-dt-for-v4.3-1b' of https://git.kernel.org/pub/scm/linux/kernel/git/mcoquelin/stm32: ARM: dts: Use stdout-path in STM32F429 Discovery board ARM: dts: Add STM32429i-EVAL board support ARM: dts: stm32f429: Adopt STM32F4 clock driver Signed-off-by: Olof Johansson <olof@lixom.net>
2015-07-27Merge tag 'sti-dt-for-v4.3-1' of ↵Olof Johansson9-36/+269
https://git.kernel.org/pub/scm/linux/kernel/git/mcoquelin/sti into next/dt STi DT update for v4.3, round 1. Highlights: ----------- - Add pinctrl configurations for transport stream channels - Add cpu-release-addr properties to STiH407 and STiH418 - Add PWM regulator support so STIH407 family - Add BDISP node to STiH407 * tag 'sti-dt-for-v4.3-1' of https://git.kernel.org/pub/scm/linux/kernel/git/mcoquelin/sti: ARM: DT: STiH410: Add bdisp dt nodes ARM: STi: STiH407: Add PWM Regulator node ARM: STi: STiH407: Move PWM nodes STiH407 => STiH407-family ARM: STi: DT: Rename st_pll3200c32_407_c0_x into st_pll3200c32_cx_x ARM: STi: DT: STiH418: Add cpu-release-addr dt property. ARM: STi: DT: STiH407: Add cpu-release-addr dt property. ARM: STi: DT: Add STiH407 family mtsin0 pinctrl configuration ARM: STi: DT: Add STiH407 family tsout1 pinctrl configuration ARM: STi: DT: Add STiH407 family tsout0 pinctrl configuration ARM: STi: DT: Add STiH407 family tsin5 pinctrl configuration ARM: STi: DT: Add STiH407 family tsin4 pinctrl configuration ARM: STi: DT: Add STiH407 family tsin3 pinctrl configuration ARM: STi: DT: Add STiH407 family tsin2 pinctrl configuration ARM: STi: DT: Add STiH407 family tsin1 pinctrl configuration ARM: STi: DT: Add STiH407 family tsin0 pinctrl configuration Signed-off-by: Olof Johansson <olof@lixom.net>
2015-07-25ARM: dts: orion5x: add buffalo linkstation ls-wtglRoger Shimizu2-0/+274
Add dts file to support Buffalo Linkstation LS-WTGL, which is marvell orion5x based 2-bay 3.5" HDD NAS. Product info: - (JPN) http://buffalo.jp/products/catalog/storage/ls-wtgl_r1/ - (ENG) http://www.buffalotech.com/support-and-downloads/download/LinkStation_Pro_Duo_Manual_web.pdf Signed-off-by: Roger Shimizu <rogershimizu@gmail.com> Acked-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
2015-07-25ARM: socfpga: dts: add osc1 as a possible parent for dbg_base_clkDinh Nguyen1-1/+1
The dbg_base_clk can also have osc1 has a parent. Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
2015-07-24ARM: OMAP2+: Add custom abort handler for t410Tony Lindgren1-0/+29
Similar to commit fdf4850cb5b2 ("ARM: BCM5301X: workaround suppress fault"), let's add custom handling for the aborts on t410 that prevent booting: Unhandled fault: imprecise external abort (0xc06) at 0xee091fb0 pgd = ee4bc000 [ee091fb0] *pgd=ae00041e(bad) Kernel panic - not syncing: Attempted to kill init! exitcode=0x00000007 Cc: Matthijs van Duin <matthijsvanduin@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2015-07-24ARM: dts: Add minimal support for HP T410Tony Lindgren2-0/+29
Add minimal support for HP T410. Cc: Matthijs van Duin <matthijsvanduin@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2015-07-24ARM: dts: Add minimal dts support for dm8148-evmTony Lindgren2-0/+29
Add minimal dts support for dm8148-evm. Cc: Matthijs van Duin <matthijsvanduin@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2015-07-24ARM: dts: Add minimal clocks for dm814xTony Lindgren2-0/+111
Use fixed clocks until we have a clock driver for the PLL. The mux and divider composite clocks work the same way as on dm816x and am335x. Cc: Matthijs van Duin <matthijsvanduin@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2015-07-24ARM: dts: Add minimal dm814x supportTony Lindgren1-0/+331
Add minimal dm814x support. Cc: Matthijs van Duin <matthijsvanduin@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2015-07-24ARM: dts: msm8974: Add smem reservation and nodeBjorn Andersson1-0/+20
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com> Signed-off-by: Andy Gross <agross@codeaurora.org>
2015-07-24ARM: dts: msm8974: Add tcsr mutex nodeBjorn Andersson1-0/+12
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com> Signed-off-by: Andy Gross <agross@codeaurora.org>
2015-07-24ARM: dts: qcom: Add ks8851 node for wired ethernetStephen Boyd2-0/+91
The micrel ks8851 device is present on MSM8960 CDP boards. It is connected to two regulators, one controlled via a gpio and another controlled via the RPM. Add the gsbi, spi, gpio regulator, and micrel ks8851 nodes so that ethernet works properly. Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Signed-off-by: Andy Gross <agross@codeaurora.org>
2015-07-24ARM: dts: qcom: Add MSM8960 CDP RPM regulatorsStephen Boyd1-0/+236
Add RPM regulators and configure their constraints on the MSM8960 CDP so that we can control these supplies. Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Signed-off-by: Andy Gross <agross@codeaurora.org>
2015-07-24ARM: dts: qcom: Add MSM8960 RPM and RPM regulator nodesStephen Boyd1-0/+19
Add the basic RPM and RPM regulator nodes that boards can fill in with their board specific details. Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Signed-off-by: Andy Gross <agross@codeaurora.org>
2015-07-24ARM: dts: qcom: Replace gpio node with pinctrl nodeStephen Boyd1-3/+2
Now that we have a proper pinctrl driver for the gpio block we can change the compatible field here and configure the pinmux on msm8960 devices. Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Signed-off-by: Andy Gross <agross@codeaurora.org>
generated by cgit v1.2.3 (git 2.39.0) at 2025-10-01 10:56:37 +0300