| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Until the endpoint is disabled, its descriptors should remain valid.
When its requests are removed from ep disable, the request completion
routine may attempt to access the endpoint's descriptor. Don't clear the
descriptors before that.
Fixes: f09ddcfcb8c5 ("usb: dwc3: gadget: Prevent EP queuing while stopping transfers")
Cc: stable@vger.kernel.org
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/45db7c83b209259115bf652af210f8b2b3b1a383.1668561364.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The core DWC3 device node was not properly removed by the custom
dwc3_exynos_remove_child() function. Replace it with generic
of_platform_depopulate() which does that job right.
Fixes: adcf20dcd262 ("usb: dwc3: exynos: Use of_platform API to create dwc3 core pdev")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Cc: stable@vger.kernel.org
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Link: https://lore.kernel.org/r/20221110154131.2577-1-m.szyprowski@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
During handling Clear Halt Endpoint Feature request, driver invokes
Reset Endpoint command. Because this command has some issue with
transition endpoint from Running to Idle state the driver must
stop the endpoint by using Stop Endpoint command.
cc: <stable@vger.kernel.org>
Fixes: 3d82904559f4 ("usb: cdnsp: cdns3 Add main part of Cadence USBSSP DRD Driver")
Reviewed-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Link: https://lore.kernel.org/r/20221110063005.370656-1-pawell@cadence.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If there's a disconnection while operating in eSS, there may be a delay
in VBUS drop response from the connector. In that case, the internal
link state may drop to operate in usb2 speed while the controller thinks
the VBUS is still high. The driver must make sure to disable
GUSB2PHYCFG.SUSPHY when sending endpoint command while in usb2 speed.
The End Transfer command may be called, and only that command needs to
go through at this point. Let's keep it simple and unconditionally
disable GUSB2PHYCFG.SUSPHY whenever we issue the command.
This scenario is not seen in real hardware. In a rare case, our
prototype type-c controller/interface may have a slow response
triggerring this issue.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/5651117207803c26e2f22ddf4e5ce9e865dcf7c7.1668045468.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Since e219a712bc06 (usb: gadget: uvc: add v4l2 try_format api call) the
try_format function is available. With this function includes checks for
valid configurations programmed in the configfs. We use this function to
ensure to return valid values on the set_format callback.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Fixes: e219a712bc06 ("usb: gadget: uvc: add v4l2 try_format api call")
Link: https://lore.kernel.org/r/20221026182240.363055-1-m.grzeschik@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
A kernel built with syzbot's config file reported that
scr_memcpyw(q, save, array3_size(logo_lines, new_cols, 2))
causes uninitialized "save" to be copied.
----------
[drm] Initialized vgem 1.0.0 20120112 for vgem on minor 0
[drm] Initialized vkms 1.0.0 20180514 for vkms on minor 1
Console: switching to colour frame buffer device 128x48
=====================================================
BUG: KMSAN: uninit-value in do_update_region+0x4b8/0xba0
do_update_region+0x4b8/0xba0
update_region+0x40d/0x840
fbcon_switch+0x3364/0x35e0
redraw_screen+0xae3/0x18a0
do_bind_con_driver+0x1cb3/0x1df0
do_take_over_console+0x11cb/0x13f0
fbcon_fb_registered+0xacc/0xfd0
register_framebuffer+0x1179/0x1320
__drm_fb_helper_initial_config_and_unlock+0x23ad/0x2b40
drm_fbdev_client_hotplug+0xbea/0xda0
drm_fbdev_generic_setup+0x65e/0x9d0
vkms_init+0x9f3/0xc76
(...snipped...)
Uninit was stored to memory at:
fbcon_prepare_logo+0x143b/0x1940
fbcon_init+0x2c1b/0x31c0
visual_init+0x3e7/0x820
do_bind_con_driver+0x14a4/0x1df0
do_take_over_console+0x11cb/0x13f0
fbcon_fb_registered+0xacc/0xfd0
register_framebuffer+0x1179/0x1320
__drm_fb_helper_initial_config_and_unlock+0x23ad/0x2b40
drm_fbdev_client_hotplug+0xbea/0xda0
drm_fbdev_generic_setup+0x65e/0x9d0
vkms_init+0x9f3/0xc76
(...snipped...)
Uninit was created at:
__kmem_cache_alloc_node+0xb69/0x1020
__kmalloc+0x379/0x680
fbcon_prepare_logo+0x704/0x1940
fbcon_init+0x2c1b/0x31c0
visual_init+0x3e7/0x820
do_bind_con_driver+0x14a4/0x1df0
do_take_over_console+0x11cb/0x13f0
fbcon_fb_registered+0xacc/0xfd0
register_framebuffer+0x1179/0x1320
__drm_fb_helper_initial_config_and_unlock+0x23ad/0x2b40
drm_fbdev_client_hotplug+0xbea/0xda0
drm_fbdev_generic_setup+0x65e/0x9d0
vkms_init+0x9f3/0xc76
(...snipped...)
CPU: 2 PID: 1 Comm: swapper/0 Not tainted 6.1.0-rc4-00356-g8f2975c2bb4c #924
Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006
----------
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/cad03d25-0ea0-32c4-8173-fd1895314bce@I-love.SAKURA.ne.jp
|
|
If PTP synchronisation is done every second, then sporadic the interval
is higher than one second:
ptp4l[696.582]: master offset -17 s2 freq -1891 path delay 573
ptp4l[697.582]: master offset -22 s2 freq -1901 path delay 573
ptp4l[699.368]: master offset -1 s2 freq -1887 path delay 573
^^^^^^^ Should be 698.582!
This problem is caused by rotten packets, which are received after
polling but before interrupts are enabled again. This can be fixed by
checking for pending work and rescheduling if necessary after interrupts
has been enabled again.
Fixes: 403f69bbdbad ("tsnep: Add TSN endpoint Ethernet MAC driver")
Signed-off-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Link: https://lore.kernel.org/r/20221119211825.81805-1-gerhard@engleder-embedded.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Colin Foster says:
====================
cleanup ocelot_stats exposure
The ocelot_stats structures became redundant across all users. Replace
this redundancy with a static const struct. After doing this, several
definitions inside include/soc/mscc/ocelot.h no longer needed to be
shared. Patch 2 removes them.
Checkpatch throws an error for a complicated macro not in parentheses. I
understand the reason for OCELOT_COMMON_STATS was to allow expansion, but
interestingly this patch set is essentially reverting the ability for
expansion. I'm keeping the macro in this set, but am open to remove it,
since it doesn't _actually_ provide any immediate benefits anymore.
====================
Link: https://lore.kernel.org/r/20221119231406.3167852-1-colin.foster@in-advantage.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Ocelot uses regmap_bulk_read() operations to efficiently read stats
registers. Currently the implementation relies on the stats layout to be
ordered to be most efficient.
Issue a warning if any future implementations happen to break this pattern.
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Co-developed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Since commit 4d1d157fb6a4 ("net: mscc: ocelot: share the common stat
definitions between all drivers") there is no longer a need to share the
stats structures to the world. Relocate these definitions to inside
ocelot_stats.c instead of a global include header.
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Ever since commit 4d1d157fb6a4 ("net: mscc: ocelot: share the common stat
definitions between all drivers") the stats_layout entry in ocelot and
felix drivers have become redundant. Remove the unnecessary code.
Suggested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
When using dash as /bin/sh, the CC_HAS_ASM_GOTO_TIED_OUTPUT test fails
with a syntax error which is not the one we are looking for:
<stdin>: In function ‘foo’:
<stdin>:1:29: warning: missing terminating " character
<stdin>:1:29: error: missing terminating " character
<stdin>:2:5: error: expected ‘:’ before ‘+’ token
<stdin>:2:7: warning: missing terminating " character
<stdin>:2:7: error: missing terminating " character
<stdin>:2:5: error: expected declaration or statement at end of input
Removing '\n' solves this.
Fixes: 1aa0e8b144b6 ("Kconfig: Add option for asm goto w/ tied outputs to workaround clang-13 bug")
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
|
|
Racing conflict could be:
task A task B
list_for_each_entry
strcmp(h->name))
list_for_each_entry
strcmp(h->name)
kzalloc kzalloc
...... .....
device_create device_create
list_add
list_add
The root cause is that task B has no idea about the fact someone
else(A) has inserted heap with same name when it calls list_add,
so a potential collision occurs.
Fixes: c02a81fba74f ("dma-buf: Add dma-buf heaps framework")
Signed-off-by: Dawei Li <set_pte_at@outlook.com>
Acked-by: Andrew Davis <afd@ti.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/TYCP286MB2323873BBDF88020781FB986CA3B9@TYCP286MB2323.JPNP286.PROD.OUTLOOK.COM
|
|
The selftests/net does not have proper cross-compilation support, and
does not properly state libbpf as a dependency. Mimic/copy the BPF
build from selftests/bpf, which has the nice side-effect that libbpf
is built as well.
Signed-off-by: Björn Töpel <bjorn@rivosinc.com>
Reviewed-by: Anders Roxell <anders.roxell@linaro.org>
Link: https://lore.kernel.org/r/20221119171841.2014936-1-bjorn@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Commit 4581dd480c9e ("net: octeontx2-pf: mcs: consider MACSEC setting")
has already added "depends on MACSEC || !MACSEC", so remove it.
Signed-off-by: Zheng Bin <zhengbin13@huawei.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://lore.kernel.org/r/20221119133616.3583538-1-zhengbin13@huawei.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
As comment of pci_get_domain_bus_and_slot() says, it returns
a pci device with refcount increment, when finish using it,
the caller must decrement the reference count by calling
pci_dev_put(). Call pci_dev_put() before returning from
bnx2x_vf_is_pcie_pending() to avoid refcount leak.
Fixes: b56e9670ffa4 ("bnx2x: Prepare device and initialize VF database")
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/20221119070202.1407648-1-yangyingliang@huawei.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The latest version of grep claims the egrep is now obsolete so the build
now contains warnings that look like:
egrep: warning: egrep is obsolescent; using grep -E
fix this up by moving the related file to use "grep -E" instead.
sed -i "s/egrep/grep -E/g" `grep egrep -rwl samples/pktgen`
Here are the steps to install the latest grep:
wget http://ftp.gnu.org/gnu/grep/grep-3.8.tar.gz
tar xf grep-3.8.tar.gz
cd grep-3.8 && ./configure && make
sudo make install
export PATH=/usr/local/bin:$PATH
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Link: https://lore.kernel.org/r/1668826504-32162-1-git-send-email-yangtiezhu@loongson.cn
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Status is reported as always off in the 6032 case. Status
reporting now matches the logic in the setters. Once of
the differences to the 6030 is that there are no groups,
therefore the state needs to be read out in the lower bits.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Link: https://lore.kernel.org/r/20221120221208.3093727-3-andreas@kemnade.info
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
In former times, info->feature was populated via the parent driver
by pdata/regulator_init_data->driver_data for all regulators when
USB_PRODUCT_ID_LSB indicates a TWL6032.
Today, the information is not set, so re-add it at the regulator
definitions.
Fixes: 25d82337705e2 ("regulator: twl: make driver DT only")
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Link: https://lore.kernel.org/r/20221120221208.3093727-2-andreas@kemnade.info
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add NULL check in dpcm_be_reparent API, to handle
kernel NULL pointer dereference error.
The issue occurred in fuzzing test.
Signed-off-by: Srinivasa Rao Mandadapu <quic_srivasam@quicinc.com>
Link: https://lore.kernel.org/r/1669098673-29703-1-git-send-email-quic_srivasam@quicinc.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Syzbot reported a memory leak about skb:
unreferenced object 0xffff88810e144e00 (size 240):
comm "syz-executor284", pid 3701, jiffies 4294952403 (age 12.620s)
hex dump (first 32 bytes):
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
[<ffffffff83ab79a9>] __alloc_skb+0x1f9/0x270 net/core/skbuff.c:497
[<ffffffff82a5cf64>] alloc_skb include/linux/skbuff.h:1267 [inline]
[<ffffffff82a5cf64>] virtual_ncidev_write+0x24/0xe0 drivers/nfc/virtual_ncidev.c:116
[<ffffffff815f6503>] do_loop_readv_writev fs/read_write.c:759 [inline]
[<ffffffff815f6503>] do_loop_readv_writev fs/read_write.c:743 [inline]
[<ffffffff815f6503>] do_iter_write+0x253/0x300 fs/read_write.c:863
[<ffffffff815f66ed>] vfs_writev+0xdd/0x240 fs/read_write.c:934
[<ffffffff815f68f6>] do_writev+0xa6/0x1c0 fs/read_write.c:977
[<ffffffff848802d5>] do_syscall_x64 arch/x86/entry/common.c:50 [inline]
[<ffffffff848802d5>] do_syscall_64+0x35/0xb0 arch/x86/entry/common.c:80
[<ffffffff84a00087>] entry_SYSCALL_64_after_hwframe+0x63/0xcd
In nci_rx_data_packet(), if we don't get a valid conn_info, we will return
directly but forget to release the skb.
Reported-by: syzbot+cdb9a427d1bc08815104@syzkaller.appspotmail.com
Fixes: 4aeee6871e8c ("NFC: nci: Add dynamic logical connections support")
Signed-off-by: Liu Shixin <liushixin2@huawei.com>
Link: https://lore.kernel.org/r/20221118082419.239475-1-liushixin2@huawei.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Current code re-calculates the size after aligning the starting and
ending physical addresses on a page boundary. But the re-calculation
also embeds the masking of high order bits that exceed the size of
the physical address space (via PHYSICAL_PAGE_MASK). If the masking
removes any high order bits, the size calculation results in a huge
value that is likely to immediately fail.
Fix this by re-calculating the page-aligned size first. Then mask any
high order bits using PHYSICAL_PAGE_MASK.
Fixes: ffa71f33a820 ("x86, ioremap: Fix incorrect physical address handling in PAE mode")
Signed-off-by: Michael Kelley <mikelley@microsoft.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Dave Hansen <dave.hansen@linux.intel.com>
Cc: <stable@kernel.org>
Link: https://lore.kernel.org/r/1668624097-14884-2-git-send-email-mikelley@microsoft.com
|
|
In commit f11fe1dae1c4 ("net/sched: Make NET_ACT_CT depends on NF_NAT"),
it fixed the build failure when NF_NAT is m and NET_ACT_CT is y by
adding depends on NF_NAT for NET_ACT_CT. However, it would also cause
NET_ACT_CT cannot be built without NF_NAT, which is not expected. This
patch fixes it by changing to use "(!NF_NAT || NF_NAT)" as the depend.
Fixes: f11fe1dae1c4 ("net/sched: Make NET_ACT_CT depends on NF_NAT")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Link: https://lore.kernel.org/r/b6386f28d1ba34721795fb776a91cbdabb203447.1668807183.git.lucien.xin@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
If phylink_of_phy_connect() fails, the port should be disabled.
If sparx5_serdes_set()/phy_power_on() fails, the port should be
disabled and the phylink should be stopped and disconnected.
Fixes: 946e7fd5053a ("net: sparx5: add port module support")
Fixes: f3cad2611a77 ("net: sparx5: add hostmode with phylink support")
Signed-off-by: Liu Jian <liujian56@huawei.com>
Tested-by: Bjarni Jonasson <bjarni.jonasson@microchip.com>
Reviewed-by: Steen Hegelund <steen.hegelund@microchip.com>
Link: https://lore.kernel.org/r/20221117125918.203997-1-liujian56@huawei.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The __ef100_hard_start_xmit() returns NETDEV_TX_OK without freeing skb
in error handling case, add dev_kfree_skb_any() to fix it.
Fixes: 51b35a454efd ("sfc: skeleton EF100 PF driver")
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Acked-by: Martin Habets <habetsm.xilinx@gmail.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/1668671409-10909-1-git-send-email-zhangchangzhong@huawei.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Zero-length arrays are deprecated[1] and are being replaced with
flexible array members in support of the ongoing efforts to tighten the
FORTIFY_SOURCE routines on memcpy(), correctly instrument array indexing
with UBSAN_BOUNDS, and to globally enable -fstrict-flex-arrays=3.
Replace zero-length array with flexible-array member.
This results in no differences in binary output (most especially because
struct pda_antenna_gain is unused). The struct is kept for future
reference.
[1] https://github.com/KSPP/linux/issues/78
Cc: Christian Lamparter <chunkeey@googlemail.com>
Cc: Kalle Valo <kvalo@kernel.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: "Gustavo A. R. Silva" <gustavoars@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221118234240.gonna.369-kees@kernel.org
|
|
The index RTW89_PHYSTS_BITMAP_NUM is not a valid physts IE page.
So, fix the check condition.
Fixes: eb4e52b3f38d ("rtw89: fix incorrect channel info during scan")
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221118042322.26794-1-pkshih@realtek.com
|
|
During doing change_interface(), hardware is power-off, so some components
are inaccessible and return error. This causes things unexpected, and we
don't have a warning message for that. So, ignore some IO operations in
this situation, and add a warning message to indicate something wrong.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221117085235.53777-1-pkshih@realtek.com
|
|
There are some registers for transmit waveform control, two of them used
in this change are for BANDEDGE and TX_SHAPE control. BANDEDGE controls
whether to apply band edge filter to transmit waveform. TX_SHAPE controls
whether to apply triangular mask to transmit waveform. It is found for
some chip, these two should be turned off during OFDMA UL traffic for
better performance.
Signed-off-by: Eric Huang <echuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221117063001.42967-3-pkshih@realtek.com
|
|
accordingly
Add macro to get FD(frequency domain) CFO field from ie_type 1, and correct
the naming for preamble CFO field. Each IC could assign the CFO source to
either FD CFO or preamble CFO in chip_info. Based on the suggestion from HW
designer, rtw8852b and its derived versions will have better CFO tracking
performance with FD CFO.
Signed-off-by: Eric Huang <echuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221117063001.42967-2-pkshih@realtek.com
|
|
When coexistence mechanism is under free-run mode, it could adjust WiFi
and BT TX power to avoid interference with each other. For other cases,
it should keep original TX power from regular predefined tables, so
set correct values to 255 for these cases.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221117061832.42057-1-pkshih@realtek.com
|
|
Prefer struct_size() over open-coded versions of idiom:
sizeof(struct-with-flex-array) + sizeof(typeof-flex-array-elements) * count
where count is the max number of items the flexible array is supposed to
contain.
In this particular case, in the open-coded version sizeof(typeof-flex-array-elements)
is implicit in _count_ because the type of the flex array data is u8:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/fwil_types.h:941:
941 struct brcmf_dload_data_le {
942 __le16 flag;
943 __le16 dload_type;
944 __le32 len;
945 __le32 crc;
946 u8 data[];
947 };
Link: https://github.com/KSPP/linux/issues/160
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/41845ad3660ed4375f0c03fd36a67b2e12fafed5.1668548907.git.gustavoars@kernel.org
|
|
struct brcmf_dload_data_le
One-element arrays are deprecated, and we are replacing them with flexible
array members instead. So, replace one-element array with flexible-array
member in struct brcmf_dload_data_le.
Important to mention is that doing a build before/after this patch results
in no binary output differences.
This helps with the ongoing efforts to tighten the FORTIFY_SOURCE routines
on memcpy() and help us make progress towards globally enabling
-fstrict-flex-arrays=3 [1].
Link: https://github.com/KSPP/linux/issues/230
Link: https://github.com/KSPP/linux/issues/79
Link: https://gcc.gnu.org/pipermail/gcc-patches/2022-October/602902.html [1]
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/905f5b68cf93c812360d081caae5b15221db09b6.1668548907.git.gustavoars@kernel.org
|
|
brcmf_gscan_config
Prefer struct_size() over open-coded versions of idiom:
sizeof(struct-with-flex-array) + sizeof(typeof-flex-array-elements) * count
where count is the max number of items the flexible array is supposed to
contain.
Also, use array_size() in call to memcpy().
Link: https://github.com/KSPP/linux/issues/160
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/de0226a549c8d000d8974e207ede786220a3df1a.1668466470.git.gustavoars@kernel.org
|
|
One-element arrays are deprecated, and we are replacing them with flexible
array members instead. So, replace one-element array with flexible-array
member in struct brcmf_gscan_config.
Important to mention is that doing a build before/after this patch results
in no binary output differences.
This helps with the ongoing efforts to tighten the FORTIFY_SOURCE routines
on memcpy() and help us make progress towards globally enabling
-fstrict-flex-arrays=3 [1].
Link: https://github.com/KSPP/linux/issues/79
Link: https://github.com/KSPP/linux/issues/241
Link: https://gcc.gnu.org/pipermail/gcc-patches/2022-October/602902.html [1]
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/7694550aa9a2753a73a687f61af9441c8cf52fd7.1668466470.git.gustavoars@kernel.org
|
|
acpi_evaluate_dsm() should be coupled with ACPI_FREE() to free the ACPI
memory, because we need to track the allocation of acpi_object when
ACPI_DBG_TRACK_ALLOCATIONS enabled, so use ACPI_FREE() instead of kfree().
Fixes: d38a648d2d6c ("net: wwan: iosm: fix memory leak in ipc_pcie_read_bios_cfg")
Signed-off-by: Wang ShaoBo <bobo.shaobowang@huawei.com>
Link: https://lore.kernel.org/r/20221118062447.2324881-1-bobo.shaobowang@huawei.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Neither Redpine Signals nor Silicon Labs seem to care about proper
maintenance of this driver, nor is there any help, documentation or
feedback on patches. The driver suffers from various problems and
subtle bugs. Mark it as orphaned.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221113185838.11643-1-marex@denx.de
|
|
1. If a profile does not support DMAC extraction then avoid installing NPC
flow rules for unicast. Similarly, if LXMB(L2 and L3) extraction is not
supported by the profile then avoid installing broadcast and multicast
rules.
2. Allow MCAM entry insertion for promiscuous mode.
3. For the profiles where DMAC is not extracted in MKEX key default
unicast entry installed by AF is not valid. Hence do not use action
from the AF installed default unicast entry for such cases.
4. Adjacent packet header fields in a packet like IP header source
and destination addresses or UDP/TCP header source port and destination
can be extracted together in MKEX profile. Therefore MKEX profile can be
configured to in two ways:
a. Total of 4 bytes from start of UDP header(src port
+ destination port)
or
b. Two bytes from start and two bytes from offset 2
Signed-off-by: Suman Ghosh <sumang@marvell.com>
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Link: https://lore.kernel.org/r/20221118053329.2288486-1-sumang@marvell.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
drm-intel-fixes
gvt-fixes-2022-11-11
- kvm reference fix from Sean
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
From: Zhenyu Wang <zhenyuw@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221111090208.GQ30028@zhen-hp.sh.intel.com
|
|
When IPv6 module initializing in xfrm6_init(), register_pernet_subsys()
is possible to fail but its return value is ignored.
If IPv6 initialization fails later and xfrm6_fini() is called,
removing uninitialized list in xfrm6_net_ops will cause null-ptr-deref:
KASAN: null-ptr-deref in range [0x0000000000000008-0x000000000000000f]
CPU: 1 PID: 330 Comm: insmod
RIP: 0010:unregister_pernet_operations+0xc9/0x450
Call Trace:
<TASK>
unregister_pernet_subsys+0x31/0x3e
xfrm6_fini+0x16/0x30 [ipv6]
ip6_route_init+0xcd/0x128 [ipv6]
inet6_init+0x29c/0x602 [ipv6]
...
Fix it by catching the error return value of register_pernet_subsys().
Fixes: 8d068875caca ("xfrm: make gc_thresh configurable in all namespaces")
Signed-off-by: Chen Zhongjin <chenzhongjin@huawei.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
|
|
Kernel 5.14 added a new "byseq" index to speed
up xfrm_state lookups by sequence number in commit
fe9f1d8779cb ("xfrm: add state hashtable keyed by seq")
While the patch was thorough, the function pfkey_send_new_mapping()
in net/af_key.c also modifies x->km.seq and never added
the current xfrm_state to the "byseq" index.
This leads to the following kernel Ooops:
BUG: kernel NULL pointer dereference, address: 0000000000000000
..
RIP: 0010:__xfrm_state_delete+0xc9/0x1c0
..
Call Trace:
<TASK>
xfrm_state_delete+0x1e/0x40
xfrm_del_sa+0xb0/0x110 [xfrm_user]
xfrm_user_rcv_msg+0x12d/0x270 [xfrm_user]
? remove_entity_load_avg+0x8a/0xa0
? copy_to_user_state_extra+0x580/0x580 [xfrm_user]
netlink_rcv_skb+0x51/0x100
xfrm_netlink_rcv+0x30/0x50 [xfrm_user]
netlink_unicast+0x1a6/0x270
netlink_sendmsg+0x22a/0x480
__sys_sendto+0x1a6/0x1c0
? __audit_syscall_entry+0xd8/0x130
? __audit_syscall_exit+0x249/0x2b0
__x64_sys_sendto+0x23/0x30
do_syscall_64+0x3a/0x90
entry_SYSCALL_64_after_hwframe+0x61/0xcb
Exact location of the crash in __xfrm_state_delete():
if (x->km.seq)
hlist_del_rcu(&x->byseq);
The hlist_node "byseq" was never populated.
The bug only triggers if a new NAT traversal mapping (changed IP or port)
is detected in esp_input_done2() / esp6_input_done2(), which in turn
indirectly calls pfkey_send_new_mapping() *if* the kernel is compiled
with CONFIG_NET_KEY and "af_key" is active.
The PF_KEYv2 message SADB_X_NAT_T_NEW_MAPPING is not part of RFC 2367.
Various implementations have been examined how they handle
the "sadb_msg_seq" header field:
- racoon (Android): does not process SADB_X_NAT_T_NEW_MAPPING
- strongswan: does not care about sadb_msg_seq
- openswan: does not care about sadb_msg_seq
There is no standard how PF_KEYv2 sadb_msg_seq should be populated
for SADB_X_NAT_T_NEW_MAPPING and it's not used in popular
implementations either. Herbert Xu suggested we should just
use the current km.seq value as is. This fixes the root cause
of the oops since we no longer modify km.seq itself.
The update of "km.seq" looks like a copy'n'paste error
from pfkey_send_acquire(). SADB_ACQUIRE must indeed assign a unique km.seq
number according to RFC 2367. It has been verified that code paths
involving pfkey_send_acquire() don't cause the same Oops.
PF_KEYv2 SADB_X_NAT_T_NEW_MAPPING support was originally added here:
https://git.kernel.org/pub/scm/linux/kernel/git/tglx/history.git
commit cbc3488685b20e7b2a98ad387a1a816aada569d8
Author: Derek Atkins <derek@ihtfp.com>
AuthorDate: Wed Apr 2 13:21:02 2003 -0800
[IPSEC]: Implement UDP Encapsulation framework.
In particular, implement ESPinUDP encapsulation for IPsec
Nat Traversal.
A note on triggering the bug: I was not able to trigger it using VMs.
There is one VPN using a high latency link on our production VPN server
that triggered it like once a day though.
Link: https://github.com/strongswan/strongswan/issues/992
Link: https://lore.kernel.org/netdev/00959f33ee52c4b3b0084d42c430418e502db554.1652340703.git.antony.antony@secunet.com/T/
Link: https://lore.kernel.org/netdev/20221027142455.3975224-1-chenzhihao@meizu.com/T/
Fixes: fe9f1d8779cb ("xfrm: add state hashtable keyed by seq")
Reported-by: Roth Mark <rothm@mail.com>
Reported-by: Zhihao Chen <chenzhihao@meizu.com>
Tested-by: Roth Mark <rothm@mail.com>
Signed-off-by: Thomas Jarosch <thomas.jarosch@intra2net.com>
Acked-by: Antony Antony <antony.antony@secunet.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
|
|
There is a race between modprobe and mount as below:
modprobe zonefs | mount -t zonefs
--------------------------------|-------------------------
zonefs_init |
register_filesystem [1] |
| zonefs_fill_super [2]
zonefs_sysfs_init [3] |
1. register zonefs suceess, then
2. user can mount the zonefs
3. if sysfs initialize failed, the module initialize failed.
Then the mount process maybe some error happened since the module
initialize failed.
Let's register zonefs after all dependency resource ready. And
reorder the dependency resource release in module exit.
Fixes: 9277a6d4fbd4 ("zonefs: Export open zone resource information through sysfs")
Signed-off-by: Zhang Xiaoxu <zhangxiaoxu5@huawei.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
|
|
Commit 1229b33973c7 ("ice: Add low latency Tx timestamp read") refactored
PTP timestamping logic to use a threaded IRQ instead of a separate kthread.
This implementation introduced ice_misc_intr_thread_fn and redefined the
ice_ptp_process_ts function interface to return a value of whether or not
the timestamp processing was complete.
ice_misc_intr_thread_fn would take the return value from ice_ptp_process_ts
and convert it into either IRQ_HANDLED if there were no more timestamps to
be processed, or IRQ_WAKE_THREAD if the thread should continue processing.
This is not correct, as the kernel does not re-schedule threaded IRQ
functions automatically. IRQ_WAKE_THREAD can only be used by the main IRQ
function.
This results in the ice_ptp_process_ts function (and in turn the
ice_ptp_tx_tstamp function) from only being called exactly once per
interrupt.
If an application sends a burst of Tx timestamps without waiting for a
response, the interrupt will trigger for the first timestamp. However,
later timestamps may not have arrived yet. This can result in dropped or
discarded timestamps. Worse, on E822 hardware this results in the interrupt
logic getting stuck such that no future interrupts will be triggered. The
result is complete loss of Tx timestamp functionality.
Fix this by modifying the ice_misc_intr_thread_fn to perform its own
polling of the ice_ptp_process_ts function. We sleep for a few microseconds
between attempts to avoid wasting significant CPU time. The value was
chosen to allow time for the Tx timestamps to complete without wasting so
much time that we overrun application wait budgets in the worst case.
The ice_ptp_process_ts function also currently returns false in the event
that the Tx tracker is not initialized. This would result in the threaded
IRQ handler never exiting if it gets started while the tracker is not
initialized.
Fix the function to appropriately return true when the tracker is not
initialized.
Note that this will not reproduce with default ptp4l behavior, as the
program always synchronously waits for a timestamp response before sending
another timestamp request.
Reported-by: Siddaraju DH <siddaraju.dh@intel.com>
Fixes: 1229b33973c7 ("ice: Add low latency Tx timestamp read")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20221118222729.1565317-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If skb_linearize() fails in tipc_disc_rcv(), we need to free the skb instead of
handle it.
Fixes: 25b0b9c4e835 ("tipc: handle collisions of 32-bit node address hash values")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Jon Maloy <jmaloy@redhat.com>
Link: https://lore.kernel.org/r/20221119072832.7896-1-yuehaibing@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2022-11-18 (iavf)
Ivan Vecera resolves issues related to reset by adding back call to
netif_tx_stop_all_queues() and adding calls to dev_close() to ensure
device is properly closed during reset.
Stefan Assmann removes waiting for setting of MAC address as this breaks
ARP.
Slawomir adds setting of __IAVF_IN_REMOVE_TASK bit to prevent deadlock
between remove and shutdown.
* '40GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
iavf: Fix race condition between iavf_shutdown and iavf_remove
iavf: remove INITIAL_MAC_SET to allow gARP to work properly
iavf: Do not restart Tx queues after reset task failure
iavf: Fix a crash during reset task
====================
Link: https://lore.kernel.org/r/20221118222439.1565245-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Xin Long says:
====================
tipc: fix two race issues in tipc_conn_alloc
The race exists beteen tipc_topsrv_accept() and tipc_conn_close(),
one is allocating the con while the other is freeing it and there
is no proper lock protecting it. Therefore, a null-pointer-defer
and a use-after-free may be triggered, see details on each patch.
====================
Link: https://lore.kernel.org/r/cover.1668807842.git.lucien.xin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
One extra conn_get() is needed in tipc_conn_alloc(), as after
tipc_conn_alloc() is called, tipc_conn_close() may free this
con before deferencing it in tipc_topsrv_accept():
tipc_conn_alloc();
newsk = newsock->sk;
<---- tipc_conn_close();
write_lock_bh(&sk->sk_callback_lock);
newsk->sk_data_ready = tipc_conn_data_ready;
Then an uaf issue can be triggered:
BUG: KASAN: use-after-free in tipc_topsrv_accept+0x1e7/0x370 [tipc]
Call Trace:
<TASK>
dump_stack_lvl+0x33/0x46
print_report+0x178/0x4b0
kasan_report+0x8c/0x100
kasan_check_range+0x179/0x1e0
tipc_topsrv_accept+0x1e7/0x370 [tipc]
process_one_work+0x6a3/0x1030
worker_thread+0x8a/0xdf0
This patch fixes it by holding it in tipc_conn_alloc(), then after
all accessing in tipc_topsrv_accept() releasing it. Note when does
this in tipc_topsrv_kern_subscr(), as tipc_conn_rcv_sub() returns
0 or -1 only, we don't need to check for "> 0".
Fixes: c5fa7b3cf3cb ("tipc: introduce new TIPC server infrastructure")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
A crash was reported by Wei Chen:
BUG: kernel NULL pointer dereference, address: 0000000000000018
RIP: 0010:tipc_conn_close+0x12/0x100
Call Trace:
tipc_topsrv_exit_net+0x139/0x320
ops_exit_list.isra.9+0x49/0x80
cleanup_net+0x31a/0x540
process_one_work+0x3fa/0x9f0
worker_thread+0x42/0x5c0
It was caused by !con->sock in tipc_conn_close(). In tipc_topsrv_accept(),
con is allocated in conn_idr then its sock is set:
con = tipc_conn_alloc();
... <----[1]
con->sock = newsock;
If tipc_conn_close() is called in anytime of [1], the null-pointer-def
is triggered by con->sock->sk due to con->sock is not yet set.
This patch fixes it by moving the con->sock setting to tipc_conn_alloc()
under s->idr_lock. So that con->sock can never be NULL when getting the
con from s->conn_idr. It will be also safer to move con->server and flag
CF_CONNECTED setting under s->idr_lock, as they should all be set before
tipc_conn_alloc() is called.
Fixes: c5fa7b3cf3cb ("tipc: introduce new TIPC server infrastructure")
Reported-by: Wei Chen <harperchen1110@gmail.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Clear the RGMII_LINK bit upon detecting link down to be consistent with
setting the bit upon link up. We also move the clearing of the
out-of-band disable to the runtime initialization rather than for each
link up/down transition.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20221118213754.1383364-1-f.fainelli@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Smatch complains that "err" can be uninitialized on these paths. Also
it's just nicer to "return 0;" instead of "return err;"
Fixes: 3a344f99bb55 ("net: microchip: sparx5: Add support for TC flower ARP dissector")
Signed-off-by: Dan Carpenter <error27@gmail.com>
Link: https://lore.kernel.org/r/Y3eg9Ml/LmLR3L3C@kili
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
