| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
With the introduction of a BCM2711 specific compatible, this also
needs to be added to the xHCI driver.
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Tested-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20231205200531.8232-3-wahrenst@gmx.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The xHCI IP on the BCM2711 SoC is compatible to "brcm,xhci-brcm-v2",
but also requires a power domain. So introduce a new compatible
and the specific constraints. Since the key allOf can only occur
once, merge the reference below.
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20231205200531.8232-2-wahrenst@gmx.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There is a potential delay in notifying Linux USB drivers of downstream
USB bus activity when connecting a high-speed or superSpeed device via the
Microchip USB491x hub. This delay is due to the fixed bInterval value of
12 in the silicon of the Microchip USB491x hub.
Microchip requested to ignore the device descriptor and decrease that
value to 9 as it was too late to modify that in silicon.
This patch speeds up the USB enummeration process that helps to pass
Apple Carplay certifications and improve the User experience when utilizing
the USB device via Microchip Multihost USB491x Hub.
A new hub quirk HUB_QUIRK_REDUCE_FRAME_INTR_BINTERVAL speeds up
the notification process for Microchip USB491x hub by limiting
the maximum bInterval value to 9.
Signed-off-by: Hardik Gajjar <hgajjar@de.adit-jv.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20231205181829.127353-2-hgajjar@de.adit-jv.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch replaces the hardcoded quirk value in the macro with
BIT().
Signed-off-by: Hardik Gajjar <hgajjar@de.adit-jv.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20231205181829.127353-1-hgajjar@de.adit-jv.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add TCPC_FAULT_STATUS_VCONN_OC constant and corresponding mask definition.
Maxim TCPC is capable of detecting VConn over current faults, so add
fault to alert mask. When a Vconn over current fault is triggered, put the
port in an error recovery state via tcpm_port_error_recovery.
Signed-off-by: RD Babiera <rdbabiera@google.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20231121203845.170234-6-rdbabiera@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add tcpm_port_error_recovery symbol and corresponding event that runs in
tcpm_pd_event handler to set the port to the ERROR_RECOVERY state. tcpci
drivers can use the symbol to reset the port when tcpc faults affect port
functionality.
Signed-off-by: RD Babiera <rdbabiera@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20231121203845.170234-5-rdbabiera@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The TPS6598x device family provides a high-level reset pin. It can be
either grounded or used to reinitialize all device settings.
Document the reset GPIO as an optional property and add it to the
existing example.
Signed-off-by: Javier Carrasco <javier.carrasco@wolfvision.net>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230912-topic-tps6598x_reset-v3-2-0c2873070a77@wolfvision.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The TPS6598x PD controller provides an active-high hardware reset input
that reinitializes all device settings. If it is not grounded by
design, the driver must be able to de-assert it in order to initialize
the device.
The PD controller is not ready for registration right after the reset
de-assertion and a delay must be introduced in that case. According to
TI, the delay can reach up to 1000 ms [1], which is in line with the
experimental results obtained with a TPS65987D.
Add a GPIO descriptor for the reset signal and basic reset management
for initialization and suspend/resume.
[1] https://e2e.ti.com/support/power-management-group/power-management/
f/power-management-forum/1269856/tps65987d-tps65987d-reset-de-assert-
to-normal-operation/4809389#4809389
Signed-off-by: Javier Carrasco <javier.carrasco@wolfvision.net>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20230912-topic-tps6598x_reset-v3-1-0c2873070a77@wolfvision.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If you deauthorize the r8152 device (by writing 0 to the "authorized"
field in sysfs) and then reauthorize it (by writing a 1) then it no
longer works. This is because when you do the above we lose the
special configuration that we set in rtl8152_cfgselector_probe().
Deauthorizing causes the config to be set to -1 and then reauthorizing
runs the default logic for choosing the best config.
I made an attempt to fix it so that the config is kept across
deauthorizing / reauthorizing [1] but it was a bit ugly.
Let's instead use the new USB core feature to override
choose_configuration().
This patch relies upon the patches ("usb: core: Don't force USB
generic_subclass drivers to define probe()") and ("usb: core: Allow
subclassed USB drivers to override usb_choose_configuration()")
[1] https://lore.kernel.org/r/20231130154337.1.Ie00e07f07f87149c9ce0b27ae4e26991d307e14b@changeid
Fixes: ec51fbd1b8a2 ("r8152: add USB device driver for config selection")
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Grant Grundler <grundler@chromium.org>
Link: https://lore.kernel.org/r/20231201102946.v2.3.Ie00e07f07f87149c9ce0b27ae4e26991d307e14b@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
For some USB devices we might want to do something different for
usb_choose_configuration(). One example here is the r8152 driver where
we want to end up using the vendor driver with the preferred
interface.
The r8152 driver tried to make things work by implementing a USB
generic_subclass driver and then overriding the normal config
selection after it happened. This is less than ideal and also caused
breakage if someone deauthorized and re-authorized the USB device
because the USB core ended up going back to it's default logic for
choosing the best config. I made an attempt to fix this [1] but it was
a bit ugly.
Let's do this better and allow USB generic_subclass drivers to
override usb_choose_configuration().
[1] https://lore.kernel.org/r/20231130154337.1.Ie00e07f07f87149c9ce0b27ae4e26991d307e14b@changeid
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20231201102946.v2.2.Iade5fa31997f1a0ca3e1dec0591633b02471df12@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There's no real reason that subclassed USB drivers _need_ to define
probe() since they might want to subclass for some other reason. Make
it optional to define probe() if we're a generic_subclass.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Grant Grundler <grundler@chromium.org>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20231201102946.v2.1.I7ea0dd55ee2acdb48b0e6d28c1a704ab2c29206f@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
sysfs_emit()
Since snprintf() has the documented, but still rather strange trait of
returning the length of the data that *would have been* written to the
array if space were available, rather than the arguably more useful
length of data *actually* written, it is usually considered wise to use
something else instead in order to avoid confusion.
In the case of sysfs call-backs, new wrappers exist that do just that.
This patch replaces just one use of snprintf() found in the sysfs
.show() call-back with the new sysfs_emit() helper.
Link: https://lwn.net/Articles/69419/
Link: https://github.com/KSPP/linux/issues/105
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: Dmitry Bogdanov <d.bogdanov@yadro.com>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20231130105459.3208986-6-lee@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
sysfs_emit()
Since snprintf() has the documented, but still rather strange trait of
returning the length of the data that *would have been* written to the
array if space were available, rather than the arguably more useful
length of data *actually* written, it is usually considered wise to use
something else instead in order to avoid confusion.
In the case of sysfs call-backs, new wrappers exist that do just that.
This patch replaces just one use of snprintf() found in the sysfs
.show() call-back with the new sysfs_emit() helper.
Link: https://lwn.net/Articles/69419/
Link: https://github.com/KSPP/linux/issues/105
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20231130105459.3208986-5-lee@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There is a general misunderstanding amongst engineers that {v}snprintf()
returns the length of the data *actually* encoded into the destination
array. However, as per the C99 standard {v}snprintf() really returns
the length of the data that *would have been* written if there were
enough space for it. This misunderstanding has led to buffer-overruns
in the past. It's generally considered safer to use the {v}scnprintf()
variants in their place (or even sprintf() in simple cases). So let's
do that.
The uses in this file both seem to assume that data *has been* written!
Link: https://lwn.net/Articles/69419/
Link: https://github.com/KSPP/linux/issues/105
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Yuan-Hsin Chen <yhchen@faraday-tech.com>
Cc: Feng-Hsin Chiang <john453@faraday-tech.com>
Cc: Po-Yu Chuang <ratbert.chuang@gmail.com>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20231130105459.3208986-4-lee@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There is a general misunderstanding amongst engineers that {v}snprintf()
returns the length of the data *actually* encoded into the destination
array. However, as per the C99 standard {v}snprintf() really returns
the length of the data that *would have been* written if there were
enough space for it. This misunderstanding has led to buffer-overruns
in the past. It's generally considered safer to use the {v}scnprintf()
variants in their place (or even sprintf() in simple cases). So let's
do that.
The uses in this file all seem to assume that data *has been* written!
Link: https://lwn.net/Articles/69419/
Link: https://github.com/KSPP/linux/issues/105
Cc: Pawel Laszczak <pawell@cadence.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20231130105459.3208986-3-lee@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Since snprintf() has the documented, but still rather strange trait of
returning the length of the data that *would have been* written to the
array if space were available, rather than the arguably more useful
length of data *actually* written, it is usually considered wise to use
something else instead in order to avoid confusion.
In the case of sysfs call-backs, new wrappers exist that do just that.
This patch replaces the 2 uses of snprintf() found in the sysfs .show()
call-backs with the new sysfs_emit() helpers. Whist we're at it, let's
replace the sprintf()s as well. For no other reason than consistency.
Link: https://lwn.net/Articles/69419/
Link: https://github.com/KSPP/linux/issues/105
Cc: Matthieu CASTET <castet.matthieu@free.fr>
Cc: Stanislaw Gruszka <stf_xl@wp.pl>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Damien Bergamini <damien.bergamini@free.fr>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20231130105459.3208986-2-lee@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There is a short gap between urb being submitted and actually added to the
endpoint queue (linked). If the device is disconnected during this time
then usb core is not yet aware of the pending urb, and device may be freed
just before xhci_urq_enqueue() continues, dereferencing the freed device.
Freeing the device is protected by the xhci spinlock, so make sure we take
and keep the lock while checking that device exists, dereference it, and
add the urb to the queue.
Remove the unnecessary URB check, usb core checks it before calling
xhci_urb_enqueue()
Suggested-by: Kuen-Han Tsai <khtsai@google.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231201150647.1307406-20-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The max packet size for full speed control endpoint 0 may vary. It is
defined in the device descriptor, which is read using the same endpoint.
Usb core sets a temporary max packet size value until the real value is
read.
xhci driver needs to reconfigure the endpoint context seen by the
controller if the max packet size changes.
It makes more sense to do this reconfiguration in xhci_endpoint_reset()
instead of urb enqueue as usb core will call endpoint reset during
enumeration if the max packet values differ.
Max packet size adjustment for endpoint 0 can only happen once per
device enumeration.
Previously the max packet size was checked during every urb enqueue.
This is an additional check for every enqueued urb, and also turned out
to have locking issues as urbs may be queued in any context while xhci
max packet size reconfiguration requires memory allocation, locking, and
sleeping.
Tested with a full speed device using both old and new scheme enumeration
and an intentionally incorrect preliminary max packet size value.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231201150647.1307406-19-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Remove extra spaces/indentation and add spaces where required.
This commit does not change any functionality.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231201150647.1307406-18-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Simplify 'xhci_try_enable_msi()' and reduce unnecessary function calls.
xHCI driver first tries to allocate 'num_online_cpu()' number of MSI-X
vectors, if that fails it falls back to a single MSI vector. There is no
good reason for this, we currently only support a primary interrupter.
However, we are still interested in knowing if there are more vectors
available, which will be utilized once we get secondary interrupter
support.
Call 'pci_alloc_irq_vectors()' once (with MSI-X and MSI flag), instead
of separately for MSI-X and MSI. And accept any number of MSI-X or MSI
vectors between 1 and 'num_online_cpu()'.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231201150647.1307406-17-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Instead of variable 'msix_count' containing the number of MSI-X vectors,
now it can contains MSI or MSI-X vector amount. Because both interrupt
methods allow several vectors. Thus, 'msix_count' is renamed to 'nvecs'.
Additionally, instead of storing the maximum possible vector amount,
now it stores the amount of successfully allocated vectors, or negative
integer on allocation failure.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231201150647.1307406-16-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The current way the xhci driver sets up MSI interrupts is overly complex
and messy. The whole MSI setup can be done in one simple function.
Continue refactoring MSI/MSI-X setup by incorporating 'xhci_setup_msi()'
into 'xhci_try_enable_msi()'. Now all interrupt enabling is contained in
one function, which should make it easier to rework.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231201150647.1307406-15-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The current way the xhci driver sets up MSI/MSI-X interrupts is overly
complex and messy. The whole MSI/MSI-X setup can be done in one simple
function.
Start refactoring this by incorporating 'xhci_setup_msix()' into
'xhci_try_enable_msi()'. 'xhci_setup_msix()' is a static function which
is only called by 'xhci_try_enable_msi()'.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231201150647.1307406-14-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Current xHCI driver only supports one "interrupter", meaning we will
only use one MSI/MSI-X interrupt line. Thus, add handler only to the
first interrupt line.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Co-developed-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231201150647.1307406-13-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Move the error check "No MSI-X/MSI found and no IRQ in BIOS" inside
'goto legacy'. It is better to check if the IRQ interrupt is available,
before trying to add a handler. Additionally the aforementioned error
message is much more clear.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231201150647.1307406-12-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Don't inherit headers "by chances" from asm/bug.h, asm/io.h,
etc... Include the needed headers explicitly.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231201150647.1307406-11-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
It is preferred to use sizeof(*pointer) instead of sizeof(type).
The type of the variable can change and one needs not change
the former (unlike the latter). No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231201150647.1307406-10-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Instead of doing custom calculations, use sizeof_field() macro.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231201150647.1307406-9-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Replace the custom return value with proper Linux error code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231201150647.1307406-8-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
kstrtox() along with regmap API can return different error codes
based on the circumstances. Don't shadow them when returning to
the caller.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231201150647.1307406-7-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The usual pattern is to check for errors and then continue if none.
Apply that pattern to xhci_dbc_stop() code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231201150647.1307406-6-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Embrace ATTRIBUTE_GROUPS() to avoid boiler plate code.
This should not introduce any functional changes.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231201150647.1307406-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Follow the advice of the Documentation/filesystems/sysfs.rst and show()
should only use sysfs_emit() or sysfs_emit_at() when formatting the
value to be returned to user space.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231201150647.1307406-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
It's standard approach to parse values from user space by using
sysfs_streq(). Make driver use it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231201150647.1307406-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
dma_free_coherent() is NULL-aware, not necessary to check for
the parameter twice. Drop duplicate conditionals in the caller.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231201150647.1307406-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The Cypress CY7C6563x is a 2/4-port USB 2.0 hub. Add support for
this hub in the driver in order to bring up reset, supply or clock
dependencies.
There is no reset pulse width given in the datasheet so we expect
a minimal value of 1us to be enough. This hasn't been tested though
due to lack of hardware which has the reset connected to a GPIO.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Link: https://lore.kernel.org/r/20231127112234.109073-3-frieder@fris.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Most onboard USB hubs have a dedicated crystal oscillator but on some
boards the clock signal for the hub is provided by the SoC.
In order to support this, we add the possibility of specifying a
clock in the devicetree that gets enabled/disabled when the hub
is powered up/down.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Link: https://lore.kernel.org/r/20231127112234.109073-2-frieder@fris.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Instead of printing the decimal error codes, let's use the more
human-readable symbolic error names provided by the %pe printk
format specifier.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Link: https://lore.kernel.org/r/20231127112234.109073-1-frieder@fris.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We need the USB/PHY/Thunderbolt fixes in here as well for later patches
to build on top of.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace
Pull tracing fixes from Steven Rostedt::
"Eventfs fixes:
- With the usage of simple_recursive_remove() recommended by Al Viro,
the code should not be calling "d_invalidate()" itself. Doing so is
causing crashes. The code was calling d_invalidate() on the race of
trying to look up a file while the parent was being deleted. This
was detected, and the added dentry was having d_invalidate() called
on it, but the deletion of the directory was also calling
d_invalidate() on that same dentry.
- A fix to not free the eventfs_inode (ei) until the last dput() was
called on its ei->dentry made the ei->dentry exist even after it
was marked for free by setting the ei->is_freed. But code elsewhere
still was checking if ei->dentry was NULL if ei->is_freed is set
and would trigger WARN_ON if that was the case. That's no longer
true and there should not be any warnings when it is true.
- Use GFP_NOFS for allocations done under eventfs_mutex. The
eventfs_mutex can be taken on file system reclaim, make sure that
allocations done under that mutex do not trigger file system
reclaim.
- Clean up code by moving the taking of inode_lock out of the helper
functions and into where they are needed, and not use the parameter
to know to take it or not. It must always be held but some callers
of the helper function have it taken when they were called.
- Warn if the inode_lock is not held in the helper functions.
- Warn if eventfs_start_creating() is called without a parent. As
eventfs is underneath tracefs, all files created will have a parent
(the top one will have a tracefs parent).
Tracing update:
- Add Mathieu Desnoyers as an official reviewer of the tracing subsystem"
* tag 'trace-v6.7-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
MAINTAINERS: TRACING: Add Mathieu Desnoyers as Reviewer
eventfs: Make sure that parent->d_inode is locked in creating files/dirs
eventfs: Do not allow NULL parent to eventfs_start_creating()
eventfs: Move taking of inode_lock into dcache_dir_open_wrapper()
eventfs: Use GFP_NOFS for allocation when eventfs_mutex is held
eventfs: Do not invalidate dentry in create_file/dir_dentry()
eventfs: Remove expectation that ei->is_freed means ei->dentry == NULL
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull parisc architecture fixes from Helge Deller:
"This patchset fixes and enforces correct section alignments for the
ex_table, altinstructions, parisc_unwind, jump_table and bug_table
which are created by inline assembly.
Due to not being correctly aligned at link & load time they can
trigger unnecessarily the kernel unaligned exception handler at
runtime. While at it, I switched the bug table to use relative
addresses which reduces the size of the table by half on 64-bit.
We still had the ENOSYM and EREMOTERELEASE errno symbols as left-overs
from HP-UX, which now trigger build-issues with glibc. We can simply
remove them.
Most of the patches are tagged for stable kernel series.
Summary:
- Drop HP-UX ENOSYM and EREMOTERELEASE return codes to avoid glibc
build issues
- Fix section alignments for ex_table, altinstructions, parisc unwind
table, jump_table and bug_table
- Reduce size of bug_table on 64-bit kernel by using relative
pointers"
* tag 'parisc-for-6.7-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Reduce size of the bug_table on 64-bit kernel by half
parisc: Drop the HP-UX ENOSYM and EREMOTERELEASE error codes
parisc: Use natural CPU alignment for bug_table
parisc: Ensure 32-bit alignment on parisc unwind section
parisc: Mark lock_aligned variables 16-byte aligned on SMP
parisc: Mark jump_table naturally aligned
parisc: Mark altinstructions read-only and 32-bit aligned
parisc: Mark ex_table entries 32-bit aligned in uaccess.h
parisc: Mark ex_table entries 32-bit aligned in assembly.h
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 microcode fixes from Ingo Molnar:
"Fix/enhance x86 microcode version reporting: fix the bootup log spam,
and remove the driver version announcement to avoid version confusion
when distros backport fixes"
* tag 'x86-urgent-2023-11-26' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/microcode: Rework early revisions reporting
x86/microcode: Remove the driver announcement and version
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 perf event fix from Ingo Molnar:
"Fix a bug in the Intel hybrid CPUs hardware-capabilities enumeration
code resulting in non-working events on those platforms"
* tag 'perf-urgent-2023-11-26' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86/intel: Correct incorrect 'or' operation for PMU capabilities
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull locking fix from Ingo Molnar:
"Fix lockdep block chain corruption resulting in KASAN warnings"
* tag 'locking-urgent-2023-11-26' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
lockdep: Fix block chain corruption
|
|
Pull smb client fixes from Steve French:
- use after free fix in releasing multichannel interfaces
- fixes for special file types (report char, block, FIFOs properly when
created e.g. by NFS to Windows)
- fixes for reporting various special file types and symlinks properly
when using SMB1
* tag '6.7-rc2-smb3-client-fixes' of git://git.samba.org/sfrench/cifs-2.6:
smb: client: introduce cifs_sfu_make_node()
smb: client: set correct file type from NFS reparse points
smb: client: introduce ->parse_reparse_point()
smb: client: implement ->query_reparse_point() for SMB1
cifs: fix use after free for iface while disabling secondary channels
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / PHY / Thunderbolt fixes from Greg KH:
"Here are a number of reverts, fixes, and new device ids for 6.7-rc3
for the USB, PHY, and Thunderbolt driver subsystems. Include in here
are:
- reverts of some PHY drivers that went into 6.7-rc1 that shouldn't
have been merged yet, the author is reworking them based on review
comments as they were using older apis that shouldn't be used
anymore for newer drivers
- small thunderbolt driver fixes for reported issues
- USB driver fixes for a variety of small issues in dwc3, typec,
xhci, and other smaller drivers.
- new device ids for usb-serial and onboard_usb_hub drivers.
All of these have been in linux-next with no reported issues"
* tag 'usb-6.7-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (33 commits)
USB: serial: option: add Luat Air72*U series products
USB: dwc3: qcom: fix ACPI platform device leak
USB: dwc3: qcom: fix software node leak on probe errors
USB: dwc3: qcom: fix resource leaks on probe deferral
USB: dwc3: qcom: simplify wakeup interrupt setup
USB: dwc3: qcom: fix wakeup after probe deferral
dt-bindings: usb: qcom,dwc3: fix example wakeup interrupt types
usb: misc: onboard-hub: add support for Microchip USB5744
dt-bindings: usb: microchip,usb5744: Add second supply
usb: misc: ljca: Fix enumeration error on Dell Latitude 9420
USB: serial: option: add Fibocom L7xx modules
USB: xhci-plat: fix legacy PHY double init
usb: typec: tipd: Supply also I2C driver data
usb: xhci-mtk: fix in-ep's start-split check failure
usb: dwc3: set the dma max_seg_size
usb: config: fix iteration issue in 'usb_get_bos_descriptor()'
usb: dwc3: add missing of_node_put and platform_device_put
USB: dwc2: write HCINT with INTMASK applied
usb: misc: ljca: Drop _ADR support to get ljca children devices
usb: cdnsp: Fix deadlock issue during using NCM gadget
...
|
|
Pull xfs fix from Chandan Babu:
- Validate quota records recovered from the log before writing them to
the disk.
* tag 'xfs-6.7-fixes-3' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
xfs: dquot recovery does not validate the recovered dquot
xfs: clean up dqblk extraction
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Catalin Marinas:
- Fix "rodata=on" not disabling "rodata=full" on arm64
- Add arm64 make dependency between vmlinuz.efi and Image, leading to
occasional build failures previously (with parallel building)
- Add newline to the output formatting of the za-fork kselftest
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: add dependency between vmlinuz.efi and Image
kselftest/arm64: Fix output formatting for za-fork
arm64: mm: Fix "rodata=on" when CONFIG_RODATA_FULL_DEFAULT_ENABLED=y
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fixes from Juergen Gross:
- A small cleanup patch for the Xen privcmd driver
- A fix for the swiotlb-xen driver which was missing the advertising of
the maximum mapping length
- A fix for Xen on Arm for a longstanding bug, which happened to occur
only recently: a structure in percpu memory crossed a page boundary,
which was rejected by the hypervisor
* tag 'for-linus-6.7a-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
arm/xen: fix xen_vcpu_info allocation alignment
xen: privcmd: Replace zero-length array with flex-array member and use __counted_by
swiotlb-xen: provide the "max_mapping_size" method
|
