summaryrefslogtreecommitdiff
AgeCommit message (Collapse)AuthorFilesLines
2016-03-14leds: Add SN3218 and SN3216 support to the IS31FL32XX driverDavid Rivshin3-7/+14
Si-En Technology was acquired by ISSI in 2011, and it appears that the IS31FL3218/IS31FL3216 are just rebranded SN3218/SN3216 devices. Add the "si-en,sn3218" and "si-en,sn3216" compatible strings into the IS31FL32XX driver as aliases for the issi equivalents, and update binding documentation. Datasheets: IS31FL3218: http://www.issi.com/WW/pdf/31FL3218.pdf SN3218: http://www.si-en.com/uploadpdf/s2011517171720.pdf IS31FL3216: http://www.issi.com/WW/pdf/31FL3216.pdf SN3216: http://www.si-en.com/uploadpdf/SN3216201152410148.pdf Signed-off-by: David Rivshin <drivshin@allworx.com> Acked-by: Rob Herring <robh@kernel.org> Tested-by: Stefan Wahren <stefan.wahren@i2se.com> Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
2016-03-14of: Add vendor prefix for Si-En TechnologyStefan Wahren1-0/+1
Si-En Technology is a fabless design house which offers audio amplifiers, LED drivers and sensors. Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
2016-03-14leds: Add driver for the ISSI IS31FL32xx family of LED controllersDavid Rivshin3-0/+513
The IS31FL32xx family of LED controllers are I2C devices with multiple constant-current channels, each with independent 256-level PWM control. Datasheets: http://www.issi.com/US/product-analog-fxled-driver.shtml This has been tested on the IS31FL3236 and IS31FL3216, on an ARM (TI am335x) platform. The programming paradigm of these devices is similar in the following ways: - All registers are 8 bit - All LED control registers are write-only - Each LED channel has a PWM register (0-255) - PWM register writes are shadowed until an Update register is poked - All have a concept of Software Shutdown, which disables output However, there are some differences in devices: - 3236/3235 have a separate Control register for each LED, (3218/3216 pack the enable bits into fewer registers) - 3236/3235 have a per-channel current divisor setting - 3236/3235 have a Global Control register that can turn off all LEDs - 3216 is unique in a number of ways - OUT9-OUT16 can be configured as GPIOs instead of LED controls - LEDs can be programmed with an 8-frame animation, with programmable delay between frames - LEDs can be modulated by an input audio signal - Max output current can be adjusted from 1/4 to 2x globally - Has a Configuration register instead of a Shutdown register This driver currently only supports the base PWM control function of these devices. The following features of these devices are not implemented, although it should be possible to add them in the future: - All devices are capable of going into a lower-power "software shutdown" mode. - The is31fl3236 and is31fl3235 can reduce the max output current per-channel with a divisor of 1, 2, 3, or 4. - The is31fl3216 can use some LED channels as GPIOs instead. - The is31fl3216 can animate LEDs in hardware. - The is31fl3216 can modulate LEDs according to an audio input. - The is31fl3216 can reduce/increase max output current globally. Signed-off-by: David Rivshin <drivshin@allworx.com> Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
2016-03-14DT: leds: Add binding for the ISSI IS31FL32xx family of LED controllersDavid Rivshin1-0/+49
This adds a binding description for the is31fl3236/35/18/16 I2C LED controllers. Signed-off-by: David Rivshin <drivshin@allworx.com> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
2016-03-14DT: Add vendor prefix for Integrated Silicon Solutions Inc.David Rivshin1-0/+1
ISSI is the stock ticker Integrated Silicon Solutions Inc. Company website: http://www.issi.com Signed-off-by: David Rivshin <drivshin@allworx.com> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
2016-03-14leds: lm3533: Use devm_led_classdev_registerAmitoj Kaur Chawla1-9/+3
Switch to resource-managed function devm_led_classdev_register instead of led_classdev_register and remove unneeded led_classdev_unregister. To be compatible with this change, remove an unnecessary label by replacing it with direct return statement. The Coccinelle semantic patch used to make this change is as follows: //<smpl> @platform@ identifier p, probefn, removefn; @@ struct platform_driver p = { .probe = probefn, .remove = removefn, }; @prb@ identifier platform.probefn, pdev; expression e; @@ probefn(struct platform_device *pdev, ...) { ... e = - led_classdev_register + devm_led_classdev_register (...); ... ?- led_classdev_unregister(...); ... } @remove depends on prb@ identifier platform.removefn; @@ removefn(...) { ... ?- led_classdev_unregister(...); ... } //</smpl> Signed-off-by: Amitoj Kaur Chawla <amitoj1606@gmail.com> Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
2016-03-14leds: gpio: Use GPIOF_OUT_INIT_LOW instead of hardcoded zeroGeert Uytterhoeven1-1/+1
Use the GPIO flag definition instead of a numeric literal, so the casual reader grepping for GPIOF_ will find the GPIO flags used. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
2016-03-14leds: core: add helpers for calling brightness_set(_blocking)Heiner Kallweit1-14/+26
Add helpers for calling brightness_set(_blocking) allowing to simplify the code and make it better readable. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
2016-03-14leds: leds-gpio: Fix return value check in create_gpio_led()Wei Yongjun1-2/+2
In case of error, the function gpio_to_desc() returns NULL pointer not ERR_PTR(). The IS_ERR() test in the return value check should be replaced with NULL test. Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn> Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
2016-03-14leds: lp3944: improve wording and formatting in a commentAntonio Ospite1-2/+5
Improve the wording for the comment about the led status, and while at it also use the standard formatting for multi-line comments. Signed-off-by: Antonio Ospite <ao2@ao2.it> Cc: Richard Purdie <rpurdie@rpsys.net> Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
2016-03-14leds: core: avoid error message when a USB LED device is unpluggedHeiner Kallweit3-1/+8
When a USB LED device is unplugged the remove call chain calls led_classdev_unregister which tries to switch the LED off. As the device has been removed already this results in a ENODEV error message in dmesg. Avoid this error message by ignoring ENODEV in calls from led_classdev_unregister if the LED device is flagged as pluggable. Therefore a new flag LED_HW_PLUGGABLE was introduced which should be set by all LED drivers handling pluggable LED devices (mainly USB LED devices). Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
2016-03-14leds: core: fix misleading comment after workqueue removal from driversHeiner Kallweit1-2/+4
Now that workqueues have been removed from individual drivers and were replaced with a core-internal workqueue we shouldn't encourage people to add new workqueues to drivers. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
2016-03-14Merge tag 'irqchip-core-4.6-3' of ↵Thomas Gleixner1-2/+5
git://git.infradead.org/users/jcooper/linux into irq/core Pull irqchip core changes from Jason Cooper: - mvebu: Update dt binding docs for new odmi driver
2016-03-14Linux 4.5Linus Torvalds1-1/+1
2016-03-14Merge branch 'turbostat' of ↵Rafael J. Wysocki3-201/+728
git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux into pm-tools Pull turbostat updates for 4.6 from Len Brown. * 'turbostat' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux: tools/power turbostat: bugfix: TDP MSRs print bits fixing tools/power turbostat: correct output for MSR_NHM_SNB_PKG_CST_CFG_CTL dump tools/power turbostat: call __cpuid() instead of __get_cpuid() tools/power turbostat: indicate SMX and SGX support tools/power turbostat: detect and work around syscall jitter tools/power turbostat: show GFX%rc6 tools/power turbostat: show GFXMHz tools/power turbostat: show IRQs per CPU tools/power turbostat: make fewer systems calls tools/power turbostat: fix compiler warnings tools/power turbostat: add --out option for saving output in a file tools/power turbostat: re-name "%Busy" field to "Busy%" tools/power turbostat: Intel Xeon x200: fix turbo-ratio decoding tools/power turbostat: Intel Xeon x200: fix erroneous bclk value tools/power turbostat: allow sub-sec intervals tools/power turbostat: Decode MSR_MISC_PWR_MGMT tools/power turbostat: decode HWP registers x86 msr-index: Simplify syntax for HWP fields tools/power turbostat: CPUID(0x16) leaf shows base, max, and bus frequency tools/power turbostat: decode more CPUID fields
2016-03-13Merge branch 'irqchip/mvebu' into irqchip/coreJason Cooper1-2/+5
2016-03-13Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linusLinus Torvalds4-5/+7
Pull MIPS fixes from Ralf Baechle: "Another round of MIPS fixes for 4.5: - Fix JZ4780 build with DEBUG_ZBOOT and MACH_JZ4780 - Fix build with DEBUG_ZBOOT and MACH_JZ4780 - Fix issue with uninitialised temp_foreign_map - Fix awk regex compile failure with certain versions of awk. At this time, the sole user, ld-ifversion, is only used on MIPS" * 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: MIPS: smp.c: Fix uninitialised temp_foreign_map MIPS: Fix build error when SMP is used without GIC ld-version: Fix awk regex compile failure MIPS: Fix build with DEBUG_ZBOOT and MACH_JZ4780
2016-03-13MIPS: smp.c: Fix uninitialised temp_foreign_mapJames Hogan1-0/+1
When calculate_cpu_foreign_map() recalculates the cpu_foreign_map cpumask it uses the local variable temp_foreign_map without initialising it to zero. Since the calculation only ever sets bits in this cpumask any existing bits at that memory location will remain set and find their way into cpu_foreign_map too. This could potentially lead to cache operations suboptimally doing smp calls to multiple VPEs in the same core, even though the VPEs share primary caches. Therefore initialise temp_foreign_map using cpumask_clear() before use. Fixes: cccf34e9411c ("MIPS: c-r4k: Fix cache flushing for MT cores") Signed-off-by: James Hogan <james.hogan@imgtec.com> Cc: Paul Burton <paul.burton@imgtec.com> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/12759/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2016-03-13MIPS: Fix build error when SMP is used without GICHauke Mehrtens1-3/+4
The MIPS_GIC_IPI should only be selected when MIPS_GIC is also selected, otherwise it results in a compile error. smp-gic.c uses some functions from include/linux/irqchip/mips-gic.h like plat_ipi_call_int_xlate() which are only added to the header file when MIPS_GIC is set. The Lantiq SoC does not use the GIC, but supports SMP. The calls top the functions from smp-gic.c are already protected by some #ifdefs The first part of this was introduced in commit 72e20142b2bf ("MIPS: Move GIC IPI functions out of smp-cmp.c") Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Cc: Paul Burton <paul.burton@imgtec.com> Cc: stable@vger.kernel.org # v3.15+ Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/12774/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2016-03-13ld-version: Fix awk regex compile failureJames Hogan1-1/+1
The ld-version.sh script fails on some versions of awk with the following error, resulting in build failures for MIPS: awk: scripts/ld-version.sh: line 4: regular expression compile failed (missing '(') This is due to the regular expression ".*)", meant to strip off the beginning of the ld version string up to the close bracket, however brackets have a meaning in regular expressions, so lets escape it so that awk doesn't expect a corresponding open bracket. Fixes: ccbef1674a15 ("Kbuild, lto: add ld-version and ld-ifversion ...") Reported-by: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: James Hogan <james.hogan@imgtec.com> Tested-by: Michael S. Tsirkin <mst@redhat.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Tested-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk> Cc: Michal Marek <mmarek@suse.com> Cc: Andi Kleen <ak@linux.intel.com> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Cc: linux-mips@linux-mips.org Cc: linux-kbuild@vger.kernel.org Cc: linux-kernel@vger.kernel.org Cc: stable@vger.kernel.org # 4.4.x- Patchwork: https://patchwork.linux-mips.org/patch/12838/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2016-03-13MIPS: Fix build with DEBUG_ZBOOT and MACH_JZ4780Aaro Koskinen1-1/+1
Ingenic SoC declares ZBOOT support, but debug definitions are missing for MACH_JZ4780 resulting in a build failure when DEBUG_ZBOOT is set. The UART addresses are same as with JZ4740, so fix by covering JZ4780 with those as well. Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/12830/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2016-03-13tools/power turbostat: bugfix: TDP MSRs print bits fixingChen Yu1-10/+10
MSR_CONFIG_TDP_NOMINAL: should print all 8 bits of base_ratio (bit 0:7) 0xFF MSR_CONFIG_TDP_LEVEL_1: should print all 15 bits of PKG_MIN_PWR_LVL1 (bit 48:62) 0x7FFF should print all 15 bits of PKG_MAX_PWR_LVL1 (bit 32:46) 0x7FFF should print all 8 bits of LVL1_RATIO (bit 16:23) 0xFF should print all 15 bits of PKG_TDP_LVL1 (bit 0:14) 0x7FFF And the same modification to MSR_CONFIG_TDP_LEVEL_2. MSR_TURBO_ACTIVATION_RATIO: should print all 8 bits of MAX_NON_TURBO_RATIO (bit 0:7) 0xFF Signed-off-by: Chen Yu <yu.c.chen@intel.com> Signed-off-by: Len Brown <len.brown@intel.com>
2016-03-13tools/power turbostat: correct output for MSR_NHM_SNB_PKG_CST_CFG_CTL dumpLen Brown1-1/+1
MSR_NHM_SNB_PKG_CST_CFG_CTL: 0x1e008008 (...pkg-cstate-limit=0: unlimited) should print as MSR_NHM_SNB_PKG_CST_CFG_CTL: 0x1e008008 (...pkg-cstate-limit=8: unlimited) Signed-off-by: Len Brown <len.brown@intel.com>
2016-03-13Merge remote-tracking branches 'regulator/topic/s5m8767' and ↵Mark Brown3-5/+10
'regulator/topic/vexpress' into regulator-next
2016-03-13Merge remote-tracking branches 'regulator/topic/mt6397', ↵Mark Brown5-40/+70
'regulator/topic/of', 'regulator/topic/pv88060', 'regulator/topic/pwm' and 'regulator/topic/s2mps11' into regulator-next
2016-03-13Merge remote-tracking branches 'regulator/topic/ltc3589', ↵Mark Brown9-10/+1047
'regulator/topic/max77620', 'regulator/topic/max77686', 'regulator/topic/max77802' and 'regulator/topic/maxim' into regulator-next
2016-03-13Merge remote-tracking branches 'regulator/topic/discharge', ↵Mark Brown15-5/+402
'regulator/topic/fan53555', 'regulator/topic/gpio', 'regulator/topic/hi655x' and 'regulator/topic/lp872x' into regulator-next
2016-03-13Merge remote-tracking branches 'regulator/topic/act8865', ↵Mark Brown9-45/+354
'regulator/topic/act8945a', 'regulator/topic/axp20x' and 'regulator/topic/cs4271' into regulator-next
2016-03-13Merge remote-tracking branch 'regulator/topic/core' into regulator-nextMark Brown1-13/+13
2016-03-13Merge remote-tracking branches 'regulator/fix/ad5398', ↵Mark Brown4-7/+14
'regulator/fix/da9210', 'regulator/fix/max77802' and 'regulator/fix/pv88090' into regulator-linus
2016-03-13Merge remote-tracking branch 'regulator/fix/core' into regulator-linusMark Brown1-17/+12
2016-03-13tools/power turbostat: call __cpuid() instead of __get_cpuid()Len Brown1-7/+7
turbostat already checks whether calling each cpuid leavf is legal, and it doesn't look at the function return value, so call the simpler gcc intrinsic __cpuid() instead of __get_cpuid(). syntax only, no functional change Signed-off-by: Len Brown <len.brown@intel.com>
2016-03-13tools/power turbostat: indicate SMX and SGX supportLen Brown1-1/+27
SGX presence is related to a SKL power workaround, so lets show when that is enabled. Signed-off-by: Len Brown <len.brown@intel.com>
2016-03-13tools/power turbostat: detect and work around syscall jitterLen Brown1-1/+50
The accuracy of Bzy_Mhz and Busy% depend on reading the TSC, APERF, and MPERF close together in time. When there is a very short measurement interval, or a large system is profoundly idle, the changes in APERF and MPERF may be very small. They can be small enough that an expensive interrupt between reading APERF and MPERF can cause the APERF/MPERF ratio to become inaccurate, resulting in invalid calculation and display of Bzy_MHz. A dummy APERF read of APERF makes this problem much more rare. Apparently this 1st systemn call after exiting a long stretch of idle is when we typically see expensive timer interrupts that cause large jitter. For the cases that dummy APERF read fails to prevent, we compare the latency of the APERF and MPERF reads. If they differ by more than 2x, we re-issue them. Signed-off-by: Len Brown <len.brown@intel.com>
2016-03-13tools/power turbostat: show GFX%rc6Len Brown1-0/+45
The column "GFX%c6" show the percentage of time the GPU is in the "render C6" state, rc6. Deep package C-states on several systems depend on the GPU being in RC6. This information comes from the counter /sys/class/drm/card0/power/rc6_residency_ms, as read before and after the measurement interval. Signed-off-by: Len Brown <len.brown@intel.com>
2016-03-13tools/power turbostat: show GFXMHzLen Brown1-1/+49
Under the column "GFXMHz", show a snapshot of this attribute: /sys/class/graphics/fb0/device/drm/card0/gt_cur_freq_mhz This is an instantaneous snapshot of what sysfs presents at the end of the measurement interval. turbostat does not average or otherwise perform any math on this value. Signed-off-by: Len Brown <len.brown@intel.com>
2016-03-13tools/power turbostat: show IRQs per CPULen Brown1-4/+122
The new IRQ column shows how many interrupts have occurred on each CPU during the measurement inteval. This information comes from the difference between /proc/interrupts shapshots made before and after the measurement interval. The first row, the system summary, shows the sum of the IRQS for all CPUs during that interval. Signed-off-by: Len Brown <len.brown@intel.com>
2016-03-13tools/power turbostat: make fewer systems callsLen Brown1-10/+41
skip the open(2)/close(2) on each msr read by keeping the /dev/cpu/*/msr files open. The remaining read(2) is generally far fewer cycles than the removed open(2) system call. Signed-off-by: Len Brown <len.brown@intel.com>
2016-03-13tools/power turbostat: fix compiler warningsLen Brown1-4/+4
Signed-off-by: Len Brown <len.brown@intel.com>
2016-03-13tools/power turbostat: add --out option for saving output in a fileLen Brown2-135/+160
By default... Turbostat --debug gconfiguration info goes to stderr. In FORK mode, turbostat statistics go to stderr. In PERIODIC mode, turbostat statistics go to stdout. These defaults do not change, but an option "--out file" will send all output above only to the specified file. Signed-off-by: Len Brown <len.brown@intel.com>
2016-03-13tools/power turbostat: re-name "%Busy" field to "Busy%"Len Brown2-11/+11
some tools processing turbostat output have difficulty with items that begin with %... Reported-by: Jacob Pan <jacob.jun.pan@linux.intel.com> Signed-off-by: Len Brown <len.brown@intel.com>
2016-03-13tools/power turbostat: Intel Xeon x200: fix turbo-ratio decodingHubert Chrzaniuk1-27/+26
Following changes have been made: - changed MSR_NHM_TURBO_RATIO_LIMIT to MSR_TURBO_RATIO_LIMIT in debug print for consistency with Developer Manual - updated definition of bitfields in MSR_TURBO_RATIO_LIMIT and appropriate parsing code - added x200 to list of architectures that do not support Nahlem compatible definition of MSR_TURBO_RATIO_LIMIT register (x200 has the register but bits definition is custom) - fixed typo in code that parses MSR_TURBO_RATIO_LIMIT (logical instead of bitwise operator) - changed MSR_TURBO_RATIO_LIMIT parsing algorithm so the print out had the same order as implementations for other platforms Signed-off-by: Hubert Chrzaniuk <hubert.chrzaniuk@intel.com> Signed-off-by: Len Brown <len.brown@intel.com>
2016-03-13tools/power turbostat: Intel Xeon x200: fix erroneous bclk valueChrzaniuk, Hubert1-1/+1
x200 does not enable any way to programmatically obtain bus clock speed. Bclk for the architecture has a fixed value of 100 MHz. At the same time x200 cannot be included in has_snb_msrs since it does not support C7 idle state. prior to this patch, MHz values reported on this chip were erroneously calculated using bclk of 133MHz, causing MHz values to be reported 33% higher than actual. Signed-off-by: Hubert Chrzaniuk <hubert.chrzaniuk@intel.com> Signed-off-by: Len Brown <len.brown@intel.com>
2016-03-13tools/power turbostat: allow sub-sec intervalsLen Brown2-5/+17
turbostat -i interval_sec will sample and display statistics every interval_sec. interval_sec used to be a whole number of seconds, but now we accept a decimal, as small as 0.001 sec (1 ms). Signed-off-by: Len Brown <len.brown@intel.com>
2016-03-13Merge branch 'for-linus' of git://git.kernel.dk/linux-blockLinus Torvalds1-5/+0
Pull block merge fix from Jens Axboe. This fixes the block segment counting bug and resulting sg overrun reported by Kent Overstreet, introduced with the last block pull. * 'for-linus' of git://git.kernel.dk/linux-block: block: don't optimize for non-cloned bio in bio_get_last_bvec()
2016-03-13Merge branch 'x86-urgent-for-linus' of ↵Linus Torvalds5-37/+79
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip Pull x86 fixes from Ingo Molnar: "This fixes 3 FPU handling related bugs, an EFI boot crash and a runtime warning. The EFI fix arrived late but I didn't want to delay it to after v4.5 because the effects are pretty bad for the systems that are affected by it" [ Actually, I don't think the EFI fix really matters yet, because we haven't switched to the separate EFI page tables in mainline yet ] * 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: x86/efi: Fix boot crash by always mapping boot service regions into new EFI page tables x86/fpu: Fix eager-FPU handling on legacy FPU machines x86/delay: Avoid preemptible context checks in delay_mwaitx() x86/fpu: Revert ("x86/fpu: Disable AVX when eagerfpu is off") x86/fpu: Fix 'no387' regression
2016-03-13Merge git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pendingLinus Torvalds1-1/+0
Pull SCSI target bug fix from Nicholas Bellinger: "Here is an outstanding target-core bug-fix for v4.5 code." This patch addresses a recent Task Management (TMR) regression related to larger set of multi-port LUN_RESET bug-fixes in v4.5-rc5. It drops a left-over target_put_sess_cmd() of se_cmd->cmd_kref within ABORT_TASK failure path, once a se_cmd descriptor has already completed posting response to fabric driver logic, and must be skipped during normal ABORT_TASK se_cmd->tag lookup" * git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: target: Drop incorrect ABORT_TASK put for completed commands
2016-03-13block: don't optimize for non-cloned bio in bio_get_last_bvec()Ming Lei1-5/+0
For !BIO_CLONED bio, we can use .bi_vcnt safely, but it doesn't mean we can just simply return .bi_io_vec[.bi_vcnt - 1] because the start postion may have been moved in the middle of the bvec, such as splitting in the middle of bvec. Fixes: 7bcd79ac50d9(block: bio: introduce helpers to get the 1st and last bvec) Cc: stable@vger.kernel.org Reported-by: Kent Overstreet <kent.overstreet@gmail.com> Signed-off-by: Ming Lei <ming.lei@canonical.com> Signed-off-by: Jens Axboe <axboe@fb.com>
2016-03-12cpu/hotplug: Document states betterThomas Gleixner1-1/+46
Requested-by: Peter Zijlstra <peterz@infradead.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2016-03-12x86/cpufeature: Enable new AVX-512 featuresFenghua Yu2-0/+6
A few new AVX-512 instruction groups/features are added in cpufeatures.h for enuermation: AVX512DQ, AVX512BW, and AVX512VL. Clear the flags in fpu__xstate_clear_all_cpu_caps(). The specification for latest AVX-512 including the features can be found at: https://software.intel.com/sites/default/files/managed/07/b7/319433-023.pdf Note, I didn't enable the flags in KVM. Hopefully the KVM guys can pick up the flags and enable them in KVM. Signed-off-by: Fenghua Yu <fenghua.yu@intel.com> Cc: Andy Lutomirski <luto@amacapital.net> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: Dave Hansen <dave.hansen@intel.com> Cc: Dave Hansen <dave.hansen@linux.intel.com> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: Gleb Natapov <gleb@kernel.org> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Oleg Nesterov <oleg@redhat.com> Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Quentin Casasnovas <quentin.casasnovas@oracle.com> Cc: Ravi V Shankar <ravi.v.shankar@intel.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: kvm@vger.kernel.org Link: http://lkml.kernel.org/r/1457667498-37357-1-git-send-email-fenghua.yu@intel.com [ Added more detailed feature descriptions. ] Signed-off-by: Ingo Molnar <mingo@kernel.org>
generated by cgit v1.2.3 (git 2.39.0) at 2025-09-28 01:27:57 +0300