| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Ipv6 ttl, label and tos fields are modified without first
pulling/pushing the ipv6 header, which would have updated
the hw csum (if available). This might cause csum validation
when sending the packet to the stack, as can be seen in
the trace below.
Fix this by updating skb->csum if available.
Trace resulted by ipv6 ttl dec and then sending packet
to conntrack [actions: set(ipv6(hlimit=63)),ct(zone=99)]:
[295241.900063] s_pf0vf2: hw csum failure
[295241.923191] Call Trace:
[295241.925728] <IRQ>
[295241.927836] dump_stack+0x5c/0x80
[295241.931240] __skb_checksum_complete+0xac/0xc0
[295241.935778] nf_conntrack_tcp_packet+0x398/0xba0 [nf_conntrack]
[295241.953030] nf_conntrack_in+0x498/0x5e0 [nf_conntrack]
[295241.958344] __ovs_ct_lookup+0xac/0x860 [openvswitch]
[295241.968532] ovs_ct_execute+0x4a7/0x7c0 [openvswitch]
[295241.979167] do_execute_actions+0x54a/0xaa0 [openvswitch]
[295242.001482] ovs_execute_actions+0x48/0x100 [openvswitch]
[295242.006966] ovs_dp_process_packet+0x96/0x1d0 [openvswitch]
[295242.012626] ovs_vport_receive+0x6c/0xc0 [openvswitch]
[295242.028763] netdev_frame_hook+0xc0/0x180 [openvswitch]
[295242.034074] __netif_receive_skb_core+0x2ca/0xcb0
[295242.047498] netif_receive_skb_internal+0x3e/0xc0
[295242.052291] napi_gro_receive+0xba/0xe0
[295242.056231] mlx5e_handle_rx_cqe_mpwrq_rep+0x12b/0x250 [mlx5_core]
[295242.062513] mlx5e_poll_rx_cq+0xa0f/0xa30 [mlx5_core]
[295242.067669] mlx5e_napi_poll+0xe1/0x6b0 [mlx5_core]
[295242.077958] net_rx_action+0x149/0x3b0
[295242.086762] __do_softirq+0xd7/0x2d6
[295242.090427] irq_exit+0xf7/0x100
[295242.093748] do_IRQ+0x7f/0xd0
[295242.096806] common_interrupt+0xf/0xf
[295242.100559] </IRQ>
[295242.102750] RIP: 0033:0x7f9022e88cbd
[295242.125246] RSP: 002b:00007f9022282b20 EFLAGS: 00000246 ORIG_RAX: ffffffffffffffda
[295242.132900] RAX: 0000000000000005 RBX: 0000000000000010 RCX: 0000000000000000
[295242.140120] RDX: 00007f9022282ba8 RSI: 00007f9022282a30 RDI: 00007f9014005c30
[295242.147337] RBP: 00007f9014014d60 R08: 0000000000000020 R09: 00007f90254a8340
[295242.154557] R10: 00007f9022282a28 R11: 0000000000000246 R12: 0000000000000000
[295242.161775] R13: 00007f902308c000 R14: 000000000000002b R15: 00007f9022b71f40
Fixes: 3fdbd1ce11e5 ("openvswitch: add ipv6 'set' action")
Signed-off-by: Paul Blakey <paulb@nvidia.com>
Link: https://lore.kernel.org/r/20220223163416.24096-1-paulb@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
valid_lft, prefered_lft and tstamp are always accessed under the lock
"lock" in other places. Reading these without taking the lock may result
in inconsistencies regarding the calculation of the valid and preferred
variables since decisions are taken on these fields for those variables.
Signed-off-by: Niels Dossche <dossche.niels@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Niels Dossche <niels.dossche@ugent.be>
Link: https://lore.kernel.org/r/20220223131954.6570-1-niels.dossche@ugent.be
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
smc_pnetid_by_table_ib() uses read_lock() and then it calls smc_pnet_apply_ib()
which, in turn, calls mutex_lock(&smc_ib_devices.mutex).
read_lock() disables preemption. Therefore, the code acquires a mutex while in
atomic context and it leads to a SAC bug.
Fix this bug by replacing the rwlock with a mutex.
Reported-and-tested-by: syzbot+4f322a6d84e991c38775@syzkaller.appspotmail.com
Fixes: 64e28b52c7a6 ("net/smc: add pnet table namespace support")
Confirmed-by: Tony Lu <tonylu@linux.alibaba.com>
Signed-off-by: Fabio M. De Francesco <fmdefrancesco@gmail.com>
Acked-by: Karsten Graul <kgraul@linux.ibm.com>
Link: https://lore.kernel.org/r/20220223100252.22562-1-fmdefrancesco@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Commit b7a49f73059f ("bnx2x: Utilize firmware 7.13.21.0") added
new firmware support in the driver with maintaining older firmware
compatibility. However, older firmware was not added in MODULE_FIRMWARE()
which caused missing firmware files in initrd image leading to driver load
failure from initrd. This patch adds MODULE_FIRMWARE() for older firmware
version to have firmware files included in initrd.
Fixes: b7a49f73059f ("bnx2x: Utilize firmware 7.13.21.0")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215627
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Alok Prasad <palok@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Link: https://lore.kernel.org/r/20220223085720.12021-1-manishc@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This reverts commit 2afeec08ab5c86ae21952151f726bfe184f6b23d.
The reasoning in the commit was wrong - the code expected to setup the
watch even if 'hotplug-status' didn't exist. In fact, it relied on the
watch being fired the first time - to check if maybe 'hotplug-status' is
already set to 'connected'. Not registering a watch for non-existing
path (which is the case if hotplug script hasn't been executed yet),
made the backend not waiting for the hotplug script to execute. This in
turns, made the netfront think the interface is fully operational, while
in fact it was not (the vif interface on xen-netback side might not be
configured yet).
This was a workaround for 'hotplug-status' erroneously being removed.
But since that is reverted now, the workaround is not necessary either.
More discussion at
https://lore.kernel.org/xen-devel/afedd7cb-a291-e773-8b0d-4db9b291fa98@ipxe.org/T/#u
Signed-off-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com>
Reviewed-by: Paul Durrant <paul@xen.org>
Reviewed-by: Michael Brown <mbrown@fensystems.co.uk>
Link: https://lore.kernel.org/r/20220222001817.2264967-2-marmarek@invisiblethingslab.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This reverts commit 1f2565780e9b7218cf92c7630130e82dcc0fe9c2.
The 'hotplug-status' node should not be removed as long as the vif
device remains configured. Otherwise the xen-netback would wait for
re-running the network script even if it was already called (in case of
the frontent re-connecting). But also, it _should_ be removed when the
vif device is destroyed (for example when unbinding the driver) -
otherwise hotplug script would not configure the device whenever it
re-appear.
Moving removal of the 'hotplug-status' node was a workaround for nothing
calling network script after xen-netback module is reloaded. But when
vif interface is re-created (on xen-netback unbind/bind for example),
the script should be called, regardless of who does that - currently
this case is not handled by the toolstack, and requires manual
script call. Keeping hotplug-status=connected to skip the call is wrong
and leads to not configured interface.
More discussion at
https://lore.kernel.org/xen-devel/afedd7cb-a291-e773-8b0d-4db9b291fa98@ipxe.org/T/#u
Signed-off-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com>
Reviewed-by: Paul Durrant <paul@xen.org>
Link: https://lore.kernel.org/r/20220222001817.2264967-1-marmarek@invisiblethingslab.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
There is a big gap between inode_should_defrag() and autodefrag extent
size threshold. For inode_should_defrag() it has a flexible
@small_write value. For compressed extent is 16K, and for non-compressed
extent it's 64K.
However for autodefrag extent size threshold, it's always fixed to the
default value (256K).
This means, the following write sequence will trigger autodefrag to
defrag ranges which didn't trigger autodefrag:
pwrite 0 8k
sync
pwrite 8k 128K
sync
The latter 128K write will also be considered as a defrag target (if
other conditions are met). While only that 8K write is really
triggering autodefrag.
Such behavior can cause extra IO for autodefrag.
Close the gap, by copying the @small_write value into inode_defrag, so
that later autodefrag can use the same @small_write value which
triggered autodefrag.
With the existing transid value, this allows autodefrag really to scan
the ranges which triggered autodefrag.
Although this behavior change is mostly reducing the extent_thresh value
for autodefrag, I believe in the future we should allow users to specify
the autodefrag extent threshold through mount options, but that's an
other problem to consider in the future.
CC: stable@vger.kernel.org # 5.16+
Signed-off-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
Pull NVMe fixes from Christoph:
"nvme fixes for Linux 5.17
- send H2CData PDUs based on MAXH2CDATA (Varun Prakash)
- fix passthrough to namespaces with unsupported features (me)"
* tag 'nvme-5.17-2022-02-24' of git://git.infradead.org/nvme:
nvme-tcp: send H2CData PDUs based on MAXH2CDATA
nvme: also mark passthrough-only namespaces ready in nvme_update_ns_info
nvme: don't return an error from nvme_configure_metadata
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for 5.17-rc6
Here's a revert of a commit which erroneously added a device id used for
the EPP/MEM mode of ch341 devices.
Included are also some new modem device ids.
All have been in linux-next with no reported issues.
* tag 'usb-serial-5.17-rc6' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: option: add Telit LE910R1 compositions
USB: serial: option: add support for DW5829e
Revert "USB: serial: ch341: add new Product ID for CH341A"
|
|
number
The battery on the 2nd hand Surface 3 which I recently bought appears to
not have a serial number programmed in. This results in any I2C reads from
the registers containing the serial number failing with an I2C NACK.
This was causing mshw0011_bix() to fail causing the battery readings to
not work at all.
Ignore EREMOTEIO (I2C NACK) errors when retrieving the serial number and
continue with an empty serial number to fix this.
Fixes: b1f81b496b0d ("platform/x86: surface3_power: MSHW0011 rev-eng implementation")
BugLink: https://github.com/linux-surface/linux-surface/issues/608
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Maximilian Luz <luzmaximilian@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20220224101848.7219-1-hdegoede@redhat.com
|
|
commit 59348401ebed ("platform/x86: amd-pmc: Add special handling for
timer based S0i3 wakeup") adds support for using another platform timer
in lieu of the RTC which doesn't work properly on some systems. This path
was validated and worked well before submission. During the 5.16-rc1 merge
window other patches were merged that caused this to stop working properly.
When this feature was used with 5.16-rc1 or later some OEM laptops with the
matching firmware requirements from that commit would shutdown instead of
program a timer based wakeup.
This was bisected to commit 8d89835b0467 ("PM: suspend: Do not pause
cpuidle in the suspend-to-idle path"). This wasn't supposed to cause any
negative impacts and also tested well on both Intel and ARM platforms.
However this changed the semantics of when CPUs are allowed to be in the
deepest state. For the AMD systems in question it appears this causes a
firmware crash for timer based wakeup.
It's hypothesized to be caused by the `amd-pmc` driver sending `OS_HINT`
and all the CPUs going into a deep state while the timer is still being
programmed. It's likely a firmware bug, but to avoid it don't allow setting
CPUs into the deepest state while using CZN timer wakeup path.
If later it's discovered that this also occurs from "regular" suspends
without a timer as well or on other silicon, this may be later expanded to
run in the suspend path for more scenarios.
Cc: stable@vger.kernel.org # 5.16+
Suggested-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://lore.kernel.org/linux-acpi/BL1PR12MB51570F5BD05980A0DCA1F3F4E23A9@BL1PR12MB5157.namprd12.prod.outlook.com/T/#mee35f39c41a04b624700ab2621c795367f19c90e
Fixes: 8d89835b0467 ("PM: suspend: Do not pause cpuidle in the suspend-to-idle path")
Fixes: 23f62d7ab25b ("PM: sleep: Pause cpuidle later and resume it earlier during system transitions")
Fixes: 59348401ebed ("platform/x86: amd-pmc: Add special handling for timer based S0i3 wakeup"
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20220223175237.6209-1-mario.limonciello@amd.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
this is a pull request of 36 patches for net-next/master.
The first 5 patches are by me and update various CAN DT bindings.
Eric Dumazet's patch for the CAN GW replaces a costly
synchronize_rcu() by a call_rcu().
The next 2 patches by me enhance the CAN bit rate handling, the bit
rate checking is simplified and the arguments and local variables of
functions are marked as const.
A patch by me for the kvaser_usb driver removes a redundant variable.
The next patch by me lets the c_can driver use the default ethtool
drvinfo.
Minghao Chi's patch for the softing driver removes a redundant
variable.
Srinivas Neeli contributes an enhancement for the xilinx_can NAPI poll
function.
Vincent Mailhol's patch for the etas_es58x driver converts to
BITS_PER_TYPE() from of manual calculation.
The next 23 patches target the mcp251xfd driver and are by me. The
first 15 patches, add support for the internal PLL, which includes
simplifying runtime PM handling, better chip detection and error
handling after wakeup, and the PLL handling. The last 8 patches
prepare the driver to support multiple RX-FIFOs and runtime
configurable RX/TX rings. The actual runtime ring configuration via
ethtool will be added in a later patch series.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There's no lock for rndis response list. It could cause list corruption
if there're two different list_add at the same time like below.
It's better to add in rndis_add_response / rndis_free_response
/ rndis_get_next_response to prevent any race condition on response list.
[ 361.894299] [1: irq/191-dwc3:16979] list_add corruption.
next->prev should be prev (ffffff80651764d0),
but was ffffff883dc36f80. (next=ffffff80651764d0).
[ 361.904380] [1: irq/191-dwc3:16979] Call trace:
[ 361.904391] [1: irq/191-dwc3:16979] __list_add_valid+0x74/0x90
[ 361.904401] [1: irq/191-dwc3:16979] rndis_msg_parser+0x168/0x8c0
[ 361.904409] [1: irq/191-dwc3:16979] rndis_command_complete+0x24/0x84
[ 361.904417] [1: irq/191-dwc3:16979] usb_gadget_giveback_request+0x20/0xe4
[ 361.904426] [1: irq/191-dwc3:16979] dwc3_gadget_giveback+0x44/0x60
[ 361.904434] [1: irq/191-dwc3:16979] dwc3_ep0_complete_data+0x1e8/0x3a0
[ 361.904442] [1: irq/191-dwc3:16979] dwc3_ep0_interrupt+0x29c/0x3dc
[ 361.904450] [1: irq/191-dwc3:16979] dwc3_process_event_entry+0x78/0x6cc
[ 361.904457] [1: irq/191-dwc3:16979] dwc3_process_event_buf+0xa0/0x1ec
[ 361.904465] [1: irq/191-dwc3:16979] dwc3_thread_interrupt+0x34/0x5c
Fixes: f6281af9d62e ("usb: gadget: rndis: use list_for_each_entry_safe")
Cc: stable <stable@kernel.org>
Signed-off-by: Daehwan Jung <dh10.jung@samsung.com>
Link: https://lore.kernel.org/r/1645507768-77687-1-git-send-email-dh10.jung@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The interrupt service routine registered for the gadget is a primary
handler which mask the interrupt source and a threaded handler which
handles the source of the interrupt. Since the threaded handler is
voluntary threaded, the IRQ-core does not disable bottom halves before
invoke the handler like it does for the forced-threaded handler.
Due to changes in networking it became visible that a network gadget's
completions handler may schedule a softirq which remains unprocessed.
The gadget's completion handler is usually invoked either in hard-IRQ or
soft-IRQ context. In this context it is enough to just raise the softirq
because the softirq itself will be handled once that context is left.
In the case of the voluntary threaded handler, there is nothing that
will process pending softirqs. Which means it remain queued until
another random interrupt (on this CPU) fires and handles it on its exit
path or another thread locks and unlocks a lock with the bh suffix.
Worst case is that the CPU goes idle and the NOHZ complains about
unhandled softirqs.
Disable bottom halves before acquiring the lock (and disabling
interrupts) and enable them after dropping the lock. This ensures that
any pending softirqs will handled right away.
Link: https://lkml.kernel.org/r/c2a64979-73d1-2c22-e048-c275c9f81558@samsung.com
Fixes: e5f68b4a3e7b0 ("Revert "usb: dwc3: gadget: remove unnecessary _irqsave()"")
Cc: stable <stable@kernel.org>
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: https://lore.kernel.org/r/Yg/YPejVQH3KkRVd@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Assure that host may not manipulate the index to point
past endpoint array.
Signed-off-by: Szymon Heidrich <szymon.heidrich@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
supported TEF/RX/TX rings
This patch introduces macros to define the number of supported TEF, RX
and TX rings. As well as some assertions as sanity checks.
Link: https://lore.kernel.org/all/20220217103826.2299157-9-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch prepares the driver to use more than one RX-FIFO. Having a
bigger RX buffer is beneficial in high load situations, where the
system temporarily cannot keep up reading CAN frames from the chip.
Using a bigger RX buffer also allows to implement RX IRQ coalescing,
which will be added in a later patch series.
If using more than 1 RX-FIFO the driver has to figure out, which FIFOs
have RX'ed CAN frames pending. This is indicated by a set bit in the
RXIF register, which is positioned directly after the interrupt status
register INT. If more than 1 RX-FIFO is used, the driver reads both
registers in 1 transfer.
The mcp251xfd_handle_rxif() function iterates over all RX rings and
reads out the RX'ed CAN frames for for all pending FIFOs. To keep the
logic for the 1 RX-FIFO only case in mcp251xfd_handle_rxif() simple,
the driver marks that FIFO pending in mcp251xfd_ring_init().
The chip has a dedicated RX interrupt line to signal pending RX'ed
frames. If connected to an input GPIO and the driver will skip the
initial read of the interrupt status register (INT) and directly read
the pending RX'ed frames if the line is active. The driver assumes the
1st RX-FIFO pending (a read of the RXIF register would re-introduce
the skipped initial read of the INT register). Any other pending
RX-FIFO will be served in the main interrupt handler.
Link: https://lore.kernel.org/all/20220217103826.2299157-8-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The recent change of the order of the TX and RX FIFOs is not reflected
in the debug info of the FIFO setup. This patch adjust the order and
additionally prints the base address of each FIFO.
Since the mcp251xfd_ring_init() may fail due to wrongly configured
FIFOs, printing of the FIFO setup is moved there. In case of an error
it would not be printed in mcp251xfd_ring_init().
Link: https://lore.kernel.org/all/20220217103826.2299157-7-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
With this patch the usage of the on-chip RAM is checked. In the
current driver the FIFO setup is fixed and always fits into the RAM.
With an upcoming patch series the ring and FIFO setup will be more
dynamic. Although using more RAM than available should not happen, but
add this safety check, just in case.
Link: https://lore.kernel.org/all/20220217103826.2299157-6-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch actually changes the order of the TX and RX FIFOs.
This gives the opportunity to minimize the number of SPI transfers in
the IRQ handler. The read of the IRQ status register and RX FIFO
status registers can be combined into single SPI transfer. If the RX
ring uses FIFO 1, the overall length of the transfer is smaller than
in the original layout, where the RX FIFO comes after the TX FIFO.
Link: https://lore.kernel.org/all/20220217103826.2299157-5-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch improves the initialization of the TX and RX rings. The
initialization functions are now called with pointers to the next free
address (in the on chip RAM) and next free hardware FIFO. The rings
are initialized using these values and the pointers are modified to
point to the next free elements.
This means the order of the mcp251xfd_ring_init_*() functions
specifies the order of the rings in the hardware FIFO. This makes it
possible to change the order of the TX and RX FIFOs, which is done in
the next patch.
This gives the opportunity to minimize the number of SPI transfers in
the IRQ handler. The read of the IRQ status register and RX FIFO
status registers can be combined into single SPI transfer. If the RX
ring uses FIFO 1, the overall length of the transfer is smaller than
in the original layout, where the RX FIFO comes after the TX FIFO.
Link: https://lore.kernel.org/all/20220217103826.2299157-4-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch splits the initialization of the TEF, TX and RX FIFO in the
mcp251xfd_ring_init() function into separate functions. This is a
preparation patch to move the RX FIFO in front of the TX FIFO.
Link: https://lore.kernel.org/all/20220217103826.2299157-3-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
make use of it
This patch removes the hard coded assumption that the TX ring uses
hardware FIFO 1. This allows the hardware FIFO 1 to be used for RX and
the next free FIFO for TX.
This gives the opportunity to minimize the number of SPI transfers in
the IRQ handler. The read of the IRQ status register and RX FIFO
status registers can be combined into single SPI transfer. If the RX
ring uses FIFO 1, the overall length of the transfer is smaller than
in the original layout, where the RX FIFO comes after the TX FIFO.
Link: https://lore.kernel.org/all/20220217103826.2299157-2-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The PLL is enabled if the configured clock is less than or equal to 10 times
the max clock frequency.
The device will operate with two different SPI speeds. A slow speed determined
by the clock without the PLL enabled, and a fast speed derived from the
frequency with the PLL enabled.
Link: https://lore.kernel.org/all/20220207131047.282110-16-mkl@pengutronix.de
Link: https://lore.kernel.org/all/20201015124401.2766-3-mas@csselectronics.com
Co-developed-by: Magnus Aagaard Sørensen <mas@csselectronics.com>
Signed-off-by: Magnus Aagaard Sørensen <mas@csselectronics.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
If the PLL is needed it must be switched on after chip reset. This
patch adds the required call to mcp251xfd_register().
Link: https://lore.kernel.org/all/20220207131047.282110-15-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
for OSC ready
This patch prepares the mcp251xfd_chip_clock_init() function for PLL
support.
If the PLL is needed is must be switched on after chip reset. This
should be done in the mcp251xfd_chip_clock_init() function. Prepare
this function to wait for the OSC and PLL to be ready.
Link: https://lore.kernel.org/all/20220207131047.282110-14-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
improve error handling and diagnostics
This patch prepares the __mcp251xfd_chip_set_mode() function for PLL
support by adding more error checks and diagnostics.
Link: https://lore.kernel.org/all/20220207131047.282110-13-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
mcp251xfd_chip_clock_enable()
This patch renames mcp251xfd_chip_clock_enable() into mcp251xfd_chip_wake() as
this function actually wakes the chip. Additionally the documentation is
adopted.
Link: https://lore.kernel.org/all/20220207131047.282110-12-mkl@pengutronix.de
Co-developed-by: Magnus Aagaard Sørensen <mas@csselectronics.com>
Signed-off-by: Magnus Aagaard Sørensen <mas@csselectronics.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
function
This patch factors out the timestamp initialization from the clock
initialization.
This is a preparation patch for the PLL support, where clock and
timestamp init must be done separately.
Link: https://lore.kernel.org/all/20220207131047.282110-11-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
accessing chip
This patch changes the order of reading the Mode and Oscillator Ready
bits.
Instead of reading the Mode of the chip directly after reset, first
wait for the oscillator to get ready and the chip to fully start up.
Read the Mode after this.
Link: https://lore.kernel.org/all/20220207131047.282110-10-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The function mcp251xfd_chip_wait_for_osc_ready() polls the Oscillator
Control Register for the oscillator to get ready. By passing the
appropriate parameters (osc_reference and osc_mask) it can also poll
for PLL ready.
This patch adjusts the error message if the Oscillator and/or PLL fail
to get ready.
Link: https://lore.kernel.org/all/20220207131047.282110-9-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
and error handling
The function mcp251xfd_chip_wait_for_osc_ready() polls the Oscillator
Control Register for the oscillator to get ready.
This is the first register the driver reads from. Reading implausible
values (all bits set or unset) can be caused by the chip starting up
after power on, waking up after sleep, or by the chip not being preset
at all. Add check for implausible register content
mcp251xfd_reg_invalid() to the regmap_read_poll_timeout() loop.
In case of a regmap_read_poll_timeout() returns a fatal error (and not
a timeout), forward it to the caller.
As mcp251xfd_chip_wait_for_osc_ready() will be called after the probe
function has finished, (currently during ifup), move error message
about failed chip detection from there into the probe function.
Link: https://lore.kernel.org/all/20220207131047.282110-8-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
separate function
This patch factors out mcp251xfd_chip_wait_for_osc_ready() into a
separate function, it will be used in several places in the next
patches.
Link: https://lore.kernel.org/all/20220207131047.282110-7-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The mcp251xfd_chip_stop() function tries the best to stop the chip and
put it into sleep mode. It continues, even if some intermediate steps
fail. As none of the callers use the return value, let this function
return void.
Link: https://lore.kernel.org/all/20220207131047.282110-6-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
into sleep mode
This patch adds a new function to bring the chip into sleep mode, and
replaces several occurrences of open coded variants.
Link: https://lore.kernel.org/all/20220207131047.282110-5-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The mcp251xfd driver supports runtime PM enabled kernels, but also
works on !CONFIG_PM configurations.
This patch simplifies the runtime PM handling in the
mcp251xfd_unregister(). In the CONFIG_PM case, runtime PM has been
enabled in the mcp251xfd_probe() function, so we can disable it here.
For !CONFIG_PM builds call mcp251xfd_clks_and_vdd_disable() directly.
Link: https://lore.kernel.org/all/20220207131047.282110-4-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
OSC register is read
MCP251XFD_REG_OSC is the first register the driver reads from. The
chip may be in deep sleep and the SPI transfer (i.e. the assertion of
the CS) will wake the chip up. This takes about 3ms. The CRC of this
transfer is wrong, or there isn't any chip at all, in this case the
CRC will be wrong, too. The driver ignores the CRC error and returns
the read data to the caller.
To avoid any confusion, this patch changes the
mcp251xfd_regmap_crc_read() function to only ignore the CRC error if
solely the OSC register is read. So when reading more than the OSC
registers at once, CRC errors are not ignored.
Link: https://lore.kernel.org/all/20220207131047.282110-3-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch renames mcp251xfd_osc_invalid() to mcp251xfd_reg_invalid(),
as it will be used for other registers than the "osc" register in a
later patch.
This patch also moves this function to more towards the beginning of
the file, to be available for other functions, too.
Link: https://lore.kernel.org/all/20220207131047.282110-2-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The input to the GENMASK() macro was calculated by hand. Replaced it
with a dedicated macro: BITS_PER_TYPE() which does the exact same job.
Link: https://lore.kernel.org/all/20220212130737.3008-1-mailhol.vincent@wanadoo.fr
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Add check for NAPI poll function to avoid enabling interrupts
with out completing the NAPI call.
Link: https://lore.kernel.org/all/20220208162053.39896-1-srinivas.neeli@xilinx.com
Signed-off-by: Srinivas Neeli <srinivas.neeli@xilinx.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Return value from softing_startstop() directly instead of taking this
in another redundant variable.
Link: https://lore.kernel.org/all/20220112080629.667191-1-chi.minghao@zte.com.cn
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Signed-off-by: CGEL ZTE <cgel.zte@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The ethtool core implements a default drvinfo.
There's no need to replicate this in the driver, no additional
information is added, so remove this and rely on the default.
Link: https://lore.kernel.org/all/20220124215642.3474154-10-mkl@pengutronix.de
Cc: Dario Binacchi <dariobin@libero.it>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The function usb_bulk_msg() can be called with a NULL pointer as the
"actual_length" parameter. This patch removes this variable.
Link: https://lore.kernel.org/all/20220124215642.3474154-9-mkl@pengutronix.de
Cc: Jimmy Assarsson <extja@kvaser.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch marks the arguments of some functions as well as some local
variables as constant.
Link: https://lore.kernel.org/all/20220124215642.3474154-7-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch simplifies the validation of the fixed bit rates. If a
supported bit rate is found, directly return 0.
If no valid bit rate is found return -EINVAL;
Link: https://lore.kernel.org/all/20220124215642.3474154-6-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Commit fb8696ab14ad ("can: gw: synchronize rcu operations
before removing gw job entry") added three synchronize_rcu() calls
to make sure one rcu grace period was observed before freeing
a "struct cgw_job" (which are tiny objects).
This should be converted to call_rcu() to avoid adding delays
in device / network dismantles.
Use the rcu_head that was already in struct cgw_job,
not yet used.
Link: https://lore.kernel.org/all/20220207190706.1499190-1-eric.dumazet@gmail.com
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Oliver Hartkopp <socketcan@hartkopp.net>
Tested-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Since commit
| 1f9234401ce0 ("dt-bindings: can: add can-controller.yaml")
there is a common CAN controller binding. Add this to the m_can
binding.
Link: https://lore.kernel.org/all/20220124220653.3477172-4-mkl@pengutronix.de
Reviewed-by: Chandrasekar Ramakrishnan <rcsekar@samsung.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch fixes the indention of the table in the description of the
bosch,mram-cfg property.
Link: https://lore.kernel.org/all/20220217101111.2291151-1-mkl@pengutronix.de
Reviewed-by: Chandrasekar Ramakrishnan <rcsekar@samsung.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Since Sriram Dash's email bounces, change the maintainer entry to
Chandrasekar Ramakrishnan. Chandrasekar Ramakrishnan is already listed
as a maintainer in the MAINTAINERS file.
Link: https://lore.kernel.org/all/20220217113839.2311417-1-mkl@pengutronix.de
Cc: Chandrasekar Ramakrishnan <rcsekar@samsung.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Since commit
| 1f9234401ce0 ("dt-bindings: can: add can-controller.yaml")
there is a common CAN controller binding. Add this to the sun4i_can
binding.
Link: https://lore.kernel.org/all/20220124220653.3477172-3-mkl@pengutronix.de
Cc: Evgeny Boger <boger@wirenboard.com>
Cc: Gerhard Bertelsmann <info@gerhard-bertelsmann.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
