summaryrefslogtreecommitdiff
AgeCommit message (Collapse)AuthorFilesLines
2014-01-14mtd: nand: support Micron READ RETRYBrian Norris2-0/+30
Micron provides READ RETRY support via the ONFI vendor-specific parameter block (to indicate how many read-retry modes are available) and the ONFI {GET,SET}_FEATURES commands with a vendor-specific feature address (to support reading/switching the current read-retry mode). The recommended sequence is as follows: 1. Perform PAGE_READ operation 2. If no ECC error, we are done 3. Run SET_FEATURES with feature address 89h, mode 1 4. Retry PAGE_READ operation 5. If ECC error and there are remaining supported modes, increment the mode and return to step 3. Otherwise, this is a true ECC error. 6. Run SET_FEATURES with feature address 89h, mode 0, to return to the default state. This patch implements the chip->setup_read_retry() callback for Micron and fills in the chip->read_retries. Tested on Micron MT29F32G08CBADA, which supports 8 read-retry modes. The Micron vendor-specific table was checked against the datasheets for the following Micron NAND: Needs retry Cell-type Part number Vendor revision Byte 180 ----------- --------- ---------------- --------------- ------------ No SLC MT29F16G08ABABA 1 Reserved (0) No MLC MT29F32G08CBABA 1 Reserved (0) No SLC MT29F1G08AACWP 1 0 Yes MLC MT29F32G08CBADA 1 08h Yes MLC MT29F64G08CBABA 2 08h Signed-off-by: Brian Norris <computersforpeace@gmail.com> Acked-by: Huang Shijie <b32955@freescale.com>
2014-01-14mtd: nand: add generic READ RETRY supportBrian Norris2-4/+58
Modern MLC (and even SLC?) NAND can experience a large number of bitflips (beyond the recommended correctability capacity) due to drifts in the voltage threshold (Vt). These bitflips can cause ECC errors to occur well within the expected lifetime of the flash. To account for this, some manufacturers provide a mechanism for shifting the Vt threshold after a corrupted read. The generic pattern seems to be that a particular flash has N read retry modes (where N = 0, traditionally), and after an ECC failure, the host should reconfigure the flash to use the next available mode, then retry the read operation. This process repeats until all bitfips can be corrected or until the host has tried all available retry modes. This patch adds the infrastructure support for a vendor-specific/flash-specific callback, used for setting the read-retry mode (i.e., voltage threshold). For now, this patch always returns the flash to mode 0 (the default mode) after a successful read-retry, according to the flowchart found in Micron's datasheets. This may need to change in the future if it is determined that eventually, mode 0 is insufficient for the majority of the flash cells (and so for performance reasons, we should leave the flash in mode 1, 2, etc.). Signed-off-by: Brian Norris <computersforpeace@gmail.com> Acked-by: Huang Shijie <b32955@freescale.com>
2014-01-14mtd: nand: add ONFI vendor block for MicronBrian Norris1-1/+22
Signed-off-by: Brian Norris <computersforpeace@gmail.com> Acked-by: Huang Shijie <b32955@freescale.com>
2014-01-14mtd: nand: localize ECC failures per pageBrian Norris1-5/+8
ECC failures can be tracked at the page level, not the do_read_ops level (i.e., a potentially multi-page transaction). This helps prepare for READ RETRY support. Signed-off-by: Brian Norris <computersforpeace@gmail.com> Acked-by: Huang Shijie <b32955@freescale.com>
2014-01-13mtd: nand: pxa3xx: Add "armada370-nand" compatibleEzequiel Garcia1-0/+4
Now that the driver can support the Armada 370/XP SoC NAND controller, add the devicetree compatible string, enabling its use. Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com> Acked-by: Jason Cooper <jason@lakedaemon.net> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2014-01-12mtd: denali: kill the NAND_MAX_PAGESIZE/NAND_MAX_OOBSIZEHuang Shijie2-24/+31
This patch kills the NAND_MAX_PAGESIZE/NAND_MAX_OOBSIZE by the following way: 1.) change the @buf field of nand_buf{} from an array to a pointer. also remove the DENALI_BUF_SIZE macro. 2.) Before we call the nand_scan_ident, we allocate a temporary buffer whose size is PAGE_SIZE. 3.) After we finish the nand_scan_ident, we have already getten the page size and oob size. We will allocate the right buffer size again. Signed-off-by: Huang Shijie <shijie8@gmail.com> Reviewed-by: Josh Triplett <josh@joshtriplett.org> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2014-01-12mtd: mxc-nand: kill the NAND_MAX_PAGESIZE/NAND_MAX_OOBSIZEHuang Shijie1-3/+15
We kill the NAND_MAX_PAGESIZE/NAND_MAX_OOBSIZE by the following way: 1.) Before we call the nand_scan_ident, we allocate a temporary buffer whose size is PAGE_SIZE. 2.) After we finish the nand_scan_ident, we have already getten the page size and oob size. We will allocate the right buffer size again. Signed-off-by: Huang Shijie <shijie8@gmail.com> Reviewed-by: Josh Triplett <josh@joshtriplett.org> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2014-01-12mtd: nand: Update mtd.name assignment type to u64 for IFC, eLBCPrabhakar Kushwaha2-2/+2
mtd.name is assigned to IFC NAND physical address. Assignment type is u32. It is not providing correct physical address of IFC NAND. Update assignment type to u64. Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2014-01-12mtd: nand: assign mtd->name in find_full_id_nandCai Zhiyong1-0/+3
This patch assigned the type->name to mtd->name when mtd->name is NULL in function "find_full_id_nand". mtd->name is NULL may cause some problem. Signed-off-by: Cai Zhiyong <caizhiyong@huawei.com> Acked-by: Huang Shijie <b32955@freescale.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2014-01-12mtd: onenand: Trivial cleanup in samsung.hSachin Kamat1-2/+0
commit 93115b7fa8f4 ("mtd: onenand/samsung: make regs-onenand.h file local") moved the file to the current location but forgot to remove the pointer to its previous location. Clean it up. Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2014-01-11mtd: orion: Cleanup mtd-orion_nand.h headerSachin Kamat1-4/+2
Commit c02cecb92ed4 ("ARM: orion: move platform_data definitions") moved the file to the current location but forgot to remove the pointer to its previous location. Clean it up. While at it also change the header file protection macros appropriately. Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2014-01-11mtd: omap2: Cleanup header filesSachin Kamat2-4/+0
Commit 2203747c9771 ("ARM: omap: move platform_data definitions") moved the files to the current location but forgot to remove the pointer to its previous location. Clean it up. Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org> Acked-by: Pekon Gupta <pekon@ti.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2014-01-09mtd: denali: Drop print of build date/timeJosh Triplett1-1/+0
The kernel already has this information, and individual drivers shouldn't duplicate that. This also eliminates the use of __DATE__ and __TIME__, which make the build non-deterministic. Signed-off-by: Josh Triplett <josh@joshtriplett.org> Reviewed-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2014-01-07mtd: bcm47xxpart: alternative MAGIC for board_data partitionRafał Miłecki1-0/+16
Some devices (like WNDR3700v3) have board_data without MPFR magic, some extra header or extra NVRAM around 0x100. In such case we have to look for another magic which is BD 0B 0D BD (BD probably stands for Board Data). It's located "far far away", so instead of extending buffer add another mtd_read. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2014-01-07mtd: bcm47xxpart: find boot partition by CFE magicRafał Miłecki1-3/+5
Some devices have even nicer-to-recognize CFE thanks to the magic. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2014-01-07mtd: Hide CONFIG_MTD_BLKDEVS from the menuEzequiel Garcia1-3/+4
Make this option a hidden one and get a cleaner configuration. This option just selects a common infrastructure for MTD-based devices to expose a block interface. There is no point in allowing a separate enable/disable. Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com> [Brian: keep symbol as tristate] Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2014-01-07mtd: onenand: fix warning (integer used as pointer)Brian Norris1-1/+1
Fixes this sparse warning: CHECK drivers/mtd/onenand/generic.c drivers/mtd/onenand/generic.c:61:62: warning: Using plain integer as NULL pointer Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2014-01-07mtd: omap2: use nand_base defaults for polled I/OBrian Norris1-7/+1
The omap_{read,write}_buf{8,16}() functions are identical to the default nand_base versions. Just let nand_base assign them in the NAND_OMAP_POLLED case. Signed-off-by: Brian Norris <computersforpeace@gmail.com> Tested-by: Pekon Gupta <pekon@ti.com>
2014-01-07mtd: nand-gpio: don't waste memory for OF failureBrian Norris1-2/+6
We shouldn't try to allocate a resource until we're sure the of_property_read_u64() call didn't fail. This is especially important if we use this code for both CONFIG_OF and !CONFIG_OF builds, since of_property_read_u64() will always return -ENOSYS for !CONFIG_OF. Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2014-01-07mtd: plat_nand: Remove unnecessary OOM messagesJingoo Han1-3/+1
The site-specific OOM messages are unnecessary, because they duplicate the MM subsystem generic OOM message. Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2014-01-07mtd: plat_nand: Use devm_*() functionsJingoo Han1-25/+6
Use devm_*() functions to make cleanup paths simpler. Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2014-01-07mtd: ixp4xx: Use devm_*() functionsJingoo Han1-22/+6
Use devm_*() functions to make cleanup paths simpler. Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2014-01-07mtd: sharpsl: use dev_err() instead of printk()Jingoo Han1-1/+1
Use dev_err() instead of printk() to provide a better message to userspace. Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2014-01-07mtd: orion_nand: use dev_err() instead of printk()Jingoo Han1-1/+1
Use dev_err() instead of printk() to provide a better message to userspace. Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2014-01-07mtd: fsmc_nand: use dev_warn() instead of printk()Jingoo Han1-4/+4
Use dev_warn() instead of printk() to provide a better message to userspace. Signed-off-by: Jingoo Han <jg1.han@samsung.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2014-01-07mtd: atmel_nand: use dev_err() instead of printk()Jingoo Han1-2/+2
Use dev_err() instead of printk() to provide a better message to userspace. Signed-off-by: Jingoo Han <jg1.han@samsung.com> Acked-by: Josh Wu <josh.wu@atmel.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2014-01-07mtd: sh_flctl: Remove unnecessary OOM messagesJingoo Han1-6/+2
The site-specific OOM messages are unnecessary, because they duplicate the MM subsystem generic OOM message. Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2014-01-07mtd: s3c2410: Remove unnecessary OOM messagesJingoo Han1-2/+0
The site-specific OOM messages are unnecessary, because they duplicate the MM subsystem generic OOM message. Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2014-01-07mtd: mpc5121_nfc: Remove unnecessary OOM messagesJingoo Han1-3/+1
The site-specific OOM messages are unnecessary, because they duplicate the MM subsystem generic OOM message. Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2014-01-07mtd: lpc32xx_slc: Remove unnecessary OOM messagesJingoo Han1-7/+2
The site-specific OOM messages are unnecessary, because they duplicate the MM subsystem generic OOM message. Signed-off-by: Jingoo Han <jg1.han@samsung.com> Acked-by: Roland Stigge <stigge@antcom.de> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2014-01-07mtd: lpc32xx_mlc: Remove unnecessary OOM messagesJingoo Han1-8/+2
The site-specific OOM messages are unnecessary, because they duplicate the MM subsystem generic OOM message. Signed-off-by: Jingoo Han <jg1.han@samsung.com> Acked-by: Roland Stigge <stigge@antcom.de> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2014-01-07mtd: nand-gpio: Remove unnecessary OOM messagesJingoo Han1-3/+1
The site-specific OOM messages are unnecessary, because they duplicate the MM subsystem generic OOM message. Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2014-01-07mtd: fsmc_nand: Remove unnecessary OOM messagesJingoo Han1-6/+2
The site-specific OOM messages are unnecessary, because they duplicate the MM subsystem generic OOM message. Signed-off-by: Jingoo Han <jg1.han@samsung.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2014-01-03mtd: davinci_nand: Remove unnecessary OOM messagesJingoo Han1-3/+1
The site-specific OOM messages are unnecessary, because they duplicate the MM subsystem generic OOM message. Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2014-01-03mtd: txx9ndfmc: Remove unnecessary OOM messagesJingoo Han1-4/+1
The site-specific OOM messages are unnecessary, because they duplicate the MM subsystem generic OOM message. Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2014-01-03mtd: jz4740_nand: Remove unnecessary OOM messagesJingoo Han1-3/+1
The site-specific OOM messages are unnecessary, because they duplicate the MM subsystem generic OOM message. Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2014-01-03mtd: fsl_ifc_nand: Remove unnecessary OOM messagesJingoo Han1-1/+0
The site-specific OOM messages are unnecessary, because they duplicate the MM subsystem generic OOM message. Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2014-01-03mtd: fsl_elbc_nand: Remove unnecessary OOM messagesJingoo Han1-1/+0
The site-specific OOM messages are unnecessary, because they duplicate the MM subsystem generic OOM message. Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2014-01-03mtd: diskonchip: Remove unnecessary OOM messagesJingoo Han1-3/+0
The site-specific OOM messages are unnecessary, because they duplicate the MM subsystem generic OOM message. Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2014-01-03mtd: cs553x_nand: Remove unnecessary OOM messagesJingoo Han1-1/+0
The site-specific OOM messages are unnecessary, because they duplicate the MM subsystem generic OOM message. Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2014-01-03mtd: cmx270_nand: Remove unnecessary OOM messagesJingoo Han1-1/+0
The site-specific OOM messages are unnecessary, because they duplicate the MM subsystem generic OOM message. Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2014-01-03mtd: cafe_nand: Remove unnecessary OOM messagesJingoo Han1-3/+1
The site-specific OOM messages are unnecessary, because they duplicate the MM subsystem generic OOM message. Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2014-01-03mtd: bf5xx_nand: Remove unnecessary OOM messagesJingoo Han1-1/+0
The site-specific OOM messages are unnecessary, because they duplicate the MM subsystem generic OOM message. Signed-off-by: Jingoo Han <jg1.han@samsung.com> Acked-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2014-01-03mtd: au1550nd: Remove unnecessary OOM messagesJingoo Han1-3/+1
The site-specific OOM messages are unnecessary, because they duplicate the MM subsystem generic OOM message. Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2014-01-03mtd: sharpsl: Remove unnecessary OOM messagesJingoo Han1-3/+1
The site-specific OOM messages are unnecessary, because they duplicate the MM subsystem generic OOM message. Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2014-01-03mtd: orion_nand: Remove unnecessary OOM messagesJingoo Han1-2/+0
The site-specific OOM messages are unnecessary, because they duplicate the MM subsystem generic OOM message. Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2014-01-03mtd: atmel_nand: Remove unnecessary OOM messagesJingoo Han1-3/+1
The site-specific OOM messages are unnecessary, because they duplicate the MM subsystem generic OOM message. Signed-off-by: Jingoo Han <jg1.han@samsung.com> Acked-by: Josh Wu <josh.wu@atmel.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2014-01-03mtd: tmio_nand: Use devm_*() functionsJingoo Han1-33/+13
Use devm_*() functions to make cleanup paths simpler. Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2014-01-03mtd: nuc900_nand: Use devm_*() functionsJingoo Han1-42/+13
Use devm_*() functions to make cleanup paths simpler. Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2014-01-03mtd: lpc32xx_slc: Use devm_*() functionsJingoo Han1-7/+3
Use devm_*() functions to make cleanup paths simpler. Signed-off-by: Jingoo Han <jg1.han@samsung.com> Acked-by: Roland Stigge <stigge@antcom.de> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
generated by cgit v1.2.3 (git 2.39.0) at 2025-09-25 09:05:56 +0300