summaryrefslogtreecommitdiff
AgeCommit message (Collapse)AuthorFilesLines
2018-03-08ARM: tegra: apalis-tk1: Hog group for ethernet, PCIe, reset GPIOsMarcel Ziswiler2-0/+28
The Apalis TK1 module uses some dedicated GPIOs as I210 gigabit Ethernet controller reset and to control RESET_MOCI aka reset module output carrier input on MXM3 pin 26. The Apalis Evaluation Board furthermore uses Apalis GPIO7 on MXM3 pin 15 as reset signal for its PLX PEX 8605 PCIe Switch. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2018-03-08ARM: tegra: apalis-tk1: Add missing as3722 gpio0 configurationMarcel Ziswiler1-3/+3
As the AS3722 GPIO0 is also a not connected on our Apalis TK1 module explicitly configure it to high-impedance as well. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2018-03-08ARM: tegra: apalis-tk1: Activate PWM pin muxing for pwm3Marcel Ziswiler1-4/+4
Activate PWM pin muxing for Apalis PWM3. Note that the same PWM3 is already active on pu6 being Apalis BKL1_PWM as well. Therefore exporting that one for raw sysfs access will fail and one has to revert to using the PWM backlight. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2018-03-08ARM: tegra: apalis-tk1: Set critical tripsMarcel Ziswiler1-24/+3
Set "critical" trip temperatures for cpu, gpu, mem and pllx thermal zones. These trips can trigger shut down or reset. Similar to commit 40823f8e267f ("arm: tegra: set critical trips for Tegra124"). Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2018-03-08ARM: tegra: apalis/colibri: Remove unneeded reg propertyMarcel Ziswiler2-2/+0
As described in Documentation/devicetree/bindings/input/touchscreen/stmpe.txt there is no 'reg' property under stmpe_touchscreen, so remove it to fix the following build warning with W=1: arch/arm/boot/dts/tegra30-apalis-eval.dtb: Warning (unit_address_vs_reg): Node /i2c@7000d000/stmpe811@41/stmpe_touchscreen has a reg or ranges property, but no unit name Similar to commit 89277e8e2679 ("ARM: dts: imx6qdl-apalis: Remove unneeded reg property"). Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2018-03-08ARM: tegra: apalis/colibri: Use correct compatible for RTCMarcel Ziswiler3-3/+3
All Toradex Carrier Boards use a st,m41t0 compatible RTC. Compared to a st,m41t00 this RTC has also an oscillator fail bit which allows to detect when the RTC lost track of time. Similar to commit c53bec16b150 ("ARM: dts: colibri/apalis: use correct compatible for RTC") covering our NXP i.MX and Vybrid based modules. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2018-03-08ARM: tegra: Fix I2C bus frequencies on Apalis/ColibriMarcel Ziswiler7-13/+18
Use a faster speed of 400 kbit/s for regular I2C busses. Use a slower speed of 10 kbit/s for DDC/EDID to improve reliability. Use a slower speed of 100 kbit/s for power I2C to be within specs of the LM95245 temperature sensor. While at it further annotate I2C pin usage. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2018-03-08ARM: tegra: venice2: Remove duplicate pcie-1 nodeMarcel Ziswiler1-5/+0
Get rid of duplicate pcie-1 node. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2018-03-08ARM: tegra: beaver: Remove invalid uses of rsvd1Marcel Ziswiler1-15/+15
Remove invalid uses of rsvd1 from Beaver device tree. Replace by actual function names of pinmux option 1. Taken from https://github.com/NVIDIA/tegra-pinmux-scripts commit b0aceda108c0 ("remove invalid uses of rsvd1 from beaver config"). Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2018-03-08ARM: tegra: Use proper IRQ type definitionsMarcel Ziswiler6-8/+8
This switches a few interrupt definitions that were using either GPIO_ACTIVE_HIGH or GPIO_ACTIVE_LOW as IRQ type, which is invalid. This is mostly a cosmetic change, that doesn't affect any driver. Analogous to Paul's commit 38333641b6dd ("ARM: tegra: nyan: Use proper IRQ type definitions"). Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2018-03-08ARM: tegra: Fix ULPI regression on Tegra20Marcel Ziswiler1-1/+1
Since commit f8f8f1d04494 ("clk: Don't touch hardware when reparenting during registration") ULPI has been broken on Tegra20 leading to the following error message during boot: [ 1.974698] ulpi_phy_power_on: ulpi write failed [ 1.979384] tegra-ehci c5004000.usb: Failed to power on the phy [ 1.985434] tegra-ehci: probe of c5004000.usb failed with error -110 Debugging through the changes and finally also consulting the TRM revealed that rather than the CDEV2 clock off OSC requiring such pin muxing actually the PLL_P_OUT4 clock is in use. It looks like so far it just worked by chance of that one having been enabled which Stephen's commit now changed when reparenting sclk away from pll_p_out4 leaving that one disabled. Fix this by properly assigning the PLL_P_OUT4 clock as the ULPI PHY clock. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Dmitry Osipenko <digetx@gmail.com> Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: Thierry Reding <treding@nvidia.com>
2018-03-08ARM: tegra: Add unit address to VDE IRAM areaThierry Reding1-1/+1
Add the missing unit address for the VDE IRAM area node in accordance with the mmio-sram device tree binding. Signed-off-by: Thierry Reding <treding@nvidia.com>
2018-03-08ARM: tegra: Add video decoder node on Tegra30Dmitry Osipenko1-0/+27
Add device tree node for the Video Decoder Engine found on Tegra30 SoC's. Signed-off-by: Dmitry Osipenko <digetx@gmail.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2018-03-08ARM: tegra: Add IRAM node on Tegra30Dmitry Osipenko1-0/+8
IRAM is a static RAM that consists of four contiguous 64 KiB blocks, it is currently used to store CPU resume code, utilized by the video decoder engine and could be used as a general-purpose fast memory. Signed-off-by: Dmitry Osipenko <digetx@gmail.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2018-02-12Linux 4.16-rc1Linus Torvalds1-2/+2
2018-02-12unify {de,}mangle_poll(), get rid of kernel-side POLL...Al Viro8-142/+47
except, again, POLLFREE and POLL_BUSY_LOOP. With this, we finally get to the promised end result: - POLL{IN,OUT,...} are plain integers and *not* in __poll_t, so any stray instances of ->poll() still using those will be caught by sparse. - eventpoll.c and select.c warning-free wrt __poll_t - no more kernel-side definitions of POLL... - userland ones are visible through the entire kernel (and used pretty much only for mangle/demangle) - same behavior as after the first series (i.e. sparc et.al. epoll(2) working correctly). Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2018-02-12vfs: do bulk POLL* -> EPOLL* replacementLinus Torvalds297-913/+913
This is the mindless scripted replacement of kernel use of POLL* variables as described by Al, done by this script: for V in IN OUT PRI ERR RDNORM RDBAND WRNORM WRBAND HUP RDHUP NVAL MSG; do L=`git grep -l -w POLL$V | grep -v '^t' | grep -v /um/ | grep -v '^sa' | grep -v '/poll.h$'|grep -v '^D'` for f in $L; do sed -i "-es/^\([^\"]*\)\(\<POLL$V\>\)/\\1E\\2/" $f; done done with de-mangling cleanups yet to come. NOTE! On almost all architectures, the EPOLL* constants have the same values as the POLL* constants do. But they keyword here is "almost". For various bad reasons they aren't the same, and epoll() doesn't actually work quite correctly in some cases due to this on Sparc et al. The next patch from Al will sort out the final differences, and we should be all done. Scripted-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2018-02-12Merge branch 'work.poll2' of ↵Linus Torvalds8-40/+47
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs Pull more poll annotation updates from Al Viro: "This is preparation to solving the problems you've mentioned in the original poll series. After this series, the kernel is ready for running for V in IN OUT PRI ERR RDNORM RDBAND WRNORM WRBAND HUP RDHUP NVAL MSG; do L=`git grep -l -w POLL$V | grep -v '^t' | grep -v /um/ | grep -v '^sa' | grep -v '/poll.h$'|grep -v '^D'` for f in $L; do sed -i "-es/^\([^\"]*\)\(\<POLL$V\>\)/\\1E\\2/" $f; done done as a for bulk search-and-replace. After that, the kernel is ready to apply the patch to unify {de,}mangle_poll(), and then get rid of kernel-side POLL... uses entirely, and we should be all done with that stuff. Basically, that's what you suggested wrt KPOLL..., except that we can use EPOLL... instead - they already are arch-independent (and equal to what is currently kernel-side POLL...). After the preparations (in this series) switch to returning EPOLL... from ->poll() instances is completely mechanical and kernel-side POLL... can go away. The last step (killing kernel-side POLL... and unifying {de,}mangle_poll() has to be done after the search-and-replace job, since we need userland-side POLL... for unified {de,}mangle_poll(), thus the cherry-pick at the last step. After that we will have: - POLL{IN,OUT,...} *not* in __poll_t, so any stray instances of ->poll() still using those will be caught by sparse. - eventpoll.c and select.c warning-free wrt __poll_t - no more kernel-side definitions of POLL... - userland ones are visible through the entire kernel (and used pretty much only for mangle/demangle) - same behavior as after the first series (i.e. sparc et.al. epoll(2) working correctly)" * 'work.poll2' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: annotate ep_scan_ready_list() ep_send_events_proc(): return result via esed->res preparation to switching ->poll() to returning EPOLL... add EPOLLNVAL, annotate EPOLL... and event_poll->event use linux/poll.h instead of asm/poll.h xen: fix poll misannotation smc: missing poll annotations
2018-02-12Merge tag 'xtensa-20180211' of git://github.com/jcmvbkbc/linux-xtensaLinus Torvalds1-0/+2
Pull xtense fix from Max Filippov: "Build fix for xtensa architecture with KASAN enabled" * tag 'xtensa-20180211' of git://github.com/jcmvbkbc/linux-xtensa: xtensa: fix build with KASAN
2018-02-12Merge tag 'nios2-v4.16-rc1' of ↵Linus Torvalds3-10/+8
git://git.kernel.org/pub/scm/linux/kernel/git/lftan/nios2 Pull nios2 update from Ley Foon Tan: - clean up old Kconfig options from defconfig - remove leading 0x and 0s from bindings notation in dts files * tag 'nios2-v4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/lftan/nios2: nios2: defconfig: Cleanup from old Kconfig options nios2: dts: Remove leading 0x and 0s from bindings notation
2018-02-11xtensa: fix build with KASANMax Filippov1-0/+2
The commit 917538e212a2 ("kasan: clean up KASAN_SHADOW_SCALE_SHIFT usage") removed KASAN_SHADOW_SCALE_SHIFT definition from include/linux/kasan.h and added it to architecture-specific headers, except for xtensa. This broke the xtensa build with KASAN enabled. Define KASAN_SHADOW_SCALE_SHIFT in arch/xtensa/include/asm/kasan.h Reported by: kbuild test robot <fengguang.wu@intel.com> Fixes: 917538e212a2 ("kasan: clean up KASAN_SHADOW_SCALE_SHIFT usage") Acked-by: Andrey Konovalov <andreyknvl@google.com> Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
2018-02-11nios2: defconfig: Cleanup from old Kconfig optionsKrzysztof Kozlowski2-2/+0
Remove old, dead Kconfig option INET_LRO. It is gone since commit 7bbf3cae65b6 ("ipv4: Remove inet_lro library"). Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Acked-by: Ley Foon Tan <ley.foon.tan@intel.com>
2018-02-11nios2: dts: Remove leading 0x and 0s from bindings notationMathieu Malaterre1-8/+8
Improve the DTS files by removing all the leading "0x" and zeros to fix the following dtc warnings: Warning (unit_address_format): Node /XXX unit name should not have leading "0x" and Warning (unit_address_format): Node /XXX unit name should not have leading 0s Converted using the following command: find . -type f \( -iname *.dts -o -iname *.dtsi \) -exec sed -E -i -e "s/@0x([0-9a-fA-F\.]+)\s?\{/@\L\1 \{/g" -e "s/@0+([0-9a-fA-F\.]+)\s?\{/@\L\1 \{/g" {} + For simplicity, two sed expressions were used to solve each warnings separately. To make the regex expression more robust a few other issues were resolved, namely setting unit-address to lower case, and adding a whitespace before the the opening curly brace: https://elinux.org/Device_Tree_Linux#Linux_conventions This is a follow up to commit 4c9847b7375a ("dt-bindings: Remove leading 0x from bindings notation") Reported-by: David Daney <ddaney@caviumnetworks.com> Suggested-by: Rob Herring <robh@kernel.org> Signed-off-by: Mathieu Malaterre <malat@debian.org> Acked-by: Ley Foon Tan <ley.foon.tan@intel.com>
2018-02-11Merge tag 'pci-v4.16-fixes-1' of ↵Linus Torvalds1-2/+3
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci Pull PCI fix from Bjorn Helgaas: "Fix a POWER9/powernv INTx regression from the merge window (Alexey Kardashevskiy)" * tag 'pci-v4.16-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: powerpc/pci: Fix broken INTx configuration via OF
2018-02-11Merge tag 'for-linus-20180210' of git://git.kernel.dk/linux-blockLinus Torvalds12-63/+212
Pull block fixes from Jens Axboe: "A few fixes to round off the merge window on the block side: - a set of bcache fixes by way of Michael Lyle, from the usual bcache suspects. - add a simple-to-hook-into function for bpf EIO error injection. - fix blk-wbt that mischarectized flushes as reads. Improve the logic so that flushes and writes are accounted as writes, and only reads as reads. From me. - fix requeue crash in BFQ, from Paolo" * tag 'for-linus-20180210' of git://git.kernel.dk/linux-block: block, bfq: add requeue-request hook bcache: fix for data collapse after re-attaching an attached device bcache: return attach error when no cache set exist bcache: set writeback_rate_update_seconds in range [1, 60] seconds bcache: fix for allocator and register thread race bcache: set error_limit correctly bcache: properly set task state in bch_writeback_thread() bcache: fix high CPU occupancy during journal bcache: add journal statistic block: Add should_fail_bio() for bpf error injection blk-wbt: account flush requests correctly
2018-02-11Merge tag 'platform-drivers-x86-v4.16-3' of git://github.com/dvhart/linux-pdx86Linus Torvalds2-11/+363
Pull x86 platform driver updates from Darren Hart: "Mellanox fixes and new system type support. Mostly data for new system types with a correction and an uninitialized variable fix" [ Pulling from github because git.infradead.org currently seems to be down for some reason, but Darren had a backup location - Linus ] * tag 'platform-drivers-x86-v4.16-3' of git://github.com/dvhart/linux-pdx86: platform/x86: mlx-platform: Add support for new 200G IB and Ethernet systems platform/x86: mlx-platform: Add support for new msn201x system type platform/x86: mlx-platform: Add support for new msn274x system type platform/x86: mlx-platform: Fix power cable setting for msn21xx family platform/x86: mlx-platform: Add define for the negative bus platform/x86: mlx-platform: Use defines for bus assignment platform/mellanox: mlxreg-hotplug: Fix uninitialized variable
2018-02-11Merge tag 'chrome-platform-for-linus-4.16' of ↵Linus Torvalds4-19/+57
git://git.kernel.org/pub/scm/linux/kernel/git/bleung/chrome-platform Pull chrome platform updates from Benson Leung: - move cros_ec_dev to drivers/mfd - other small maintenance fixes [ The cros_ec_dev movement came in earlier through the MFD tree - Linus ] * tag 'chrome-platform-for-linus-4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/bleung/chrome-platform: platform/chrome: Use proper protocol transfer function platform/chrome: cros_ec_lpc: Add support for Google Glimmer platform/chrome: cros_ec_lpc: Register the driver if ACPI entry is missing. platform/chrome: cros_ec_lpc: remove redundant pointer request cros_ec: fix nul-termination for firmware build info platform/chrome: chromeos_laptop: make chromeos_laptop const
2018-02-11Merge tag 'kvm-4.16-1' of git://git.kernel.org/pub/scm/virt/kvm/kvmLinus Torvalds123-1416/+6577
Pull KVM updates from Radim Krčmář: "ARM: - icache invalidation optimizations, improving VM startup time - support for forwarded level-triggered interrupts, improving performance for timers and passthrough platform devices - a small fix for power-management notifiers, and some cosmetic changes PPC: - add MMIO emulation for vector loads and stores - allow HPT guests to run on a radix host on POWER9 v2.2 CPUs without requiring the complex thread synchronization of older CPU versions - improve the handling of escalation interrupts with the XIVE interrupt controller - support decrement register migration - various cleanups and bugfixes. s390: - Cornelia Huck passed maintainership to Janosch Frank - exitless interrupts for emulated devices - cleanup of cpuflag handling - kvm_stat counter improvements - VSIE improvements - mm cleanup x86: - hypervisor part of SEV - UMIP, RDPID, and MSR_SMI_COUNT emulation - paravirtualized TLB shootdown using the new KVM_VCPU_PREEMPTED bit - allow guests to see TOPOEXT, GFNI, VAES, VPCLMULQDQ, and more AVX512 features - show vcpu id in its anonymous inode name - many fixes and cleanups - per-VCPU MSR bitmaps (already merged through x86/pti branch) - stable KVM clock when nesting on Hyper-V (merged through x86/hyperv)" * tag 'kvm-4.16-1' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (197 commits) KVM: PPC: Book3S: Add MMIO emulation for VMX instructions KVM: PPC: Book3S HV: Branch inside feature section KVM: PPC: Book3S HV: Make HPT resizing work on POWER9 KVM: PPC: Book3S HV: Fix handling of secondary HPTEG in HPT resizing code KVM: PPC: Book3S PR: Fix broken select due to misspelling KVM: x86: don't forget vcpu_put() in kvm_arch_vcpu_ioctl_set_sregs() KVM: PPC: Book3S PR: Fix svcpu copying with preemption enabled KVM: PPC: Book3S HV: Drop locks before reading guest memory kvm: x86: remove efer_reload entry in kvm_vcpu_stat KVM: x86: AMD Processor Topology Information x86/kvm/vmx: do not use vm-exit instruction length for fast MMIO when running nested kvm: embed vcpu id to dentry of vcpu anon inode kvm: Map PFN-type memory regions as writable (if possible) x86/kvm: Make it compile on 32bit and with HYPYERVISOR_GUEST=n KVM: arm/arm64: Fixup userspace irqchip static key optimization KVM: arm/arm64: Fix userspace_irqchip_in_use counting KVM: arm/arm64: Fix incorrect timer_is_pending logic MAINTAINERS: update KVM/s390 maintainers MAINTAINERS: add Halil as additional vfio-ccw maintainer MAINTAINERS: add David as a reviewer for KVM/s390 ...
2018-02-10powerpc/pci: Fix broken INTx configuration via OFAlexey Kardashevskiy1-2/+3
59f47eff03a0 ("powerpc/pci: Use of_irq_parse_and_map_pci() helper") replaced of_irq_parse_pci() + irq_create_of_mapping() with of_irq_parse_and_map_pci(), but neglected to capture the virq returned by irq_create_of_mapping(), so virq remained zero, which caused INTx configuration to fail. Save the virq value returned by of_irq_parse_and_map_pci() and correct the virq declaration to match the of_irq_parse_and_map_pci() signature. Fixes: 59f47eff03a0 "powerpc/pci: Use of_irq_parse_and_map_pci() helper" Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru> [bhelgaas: changelog] Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2018-02-10Merge tag 'kbuild-v4.16-2' of ↵Linus Torvalds23-77/+121
git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild Pull more Kbuild updates from Masahiro Yamada: "Makefile changes: - enable unused-variable warning that was wrongly disabled for clang Kconfig changes: - warn about blank 'help' and fix existing instances - fix 'choice' behavior to not write out invisible symbols - fix misc weirdness Coccinell changes: - fix false positive of free after managed memory alloc detection - improve performance of NULL dereference detection" * tag 'kbuild-v4.16-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (21 commits) kconfig: remove const qualifier from sym_expand_string_value() kconfig: add xrealloc() helper kconfig: send error messages to stderr kconfig: echo stdin to stdout if either is redirected kconfig: remove check_stdin() kconfig: remove 'config*' pattern from .gitignnore kconfig: show '?' prompt even if no help text is available kconfig: do not write choice values when their dependency becomes n coccinelle: deref_null: avoid useless computation coccinelle: devm_free: reduce false positives kbuild: clang: disable unused variable warnings only when constant kconfig: Warn if help text is blank nios2: kconfig: Remove blank help text arm: vt8500: kconfig: Remove blank help text MIPS: kconfig: Remove blank help text MIPS: BCM63XX: kconfig: Remove blank help text lib/Kconfig.debug: Remove blank help text Staging: rtl8192e: kconfig: Remove blank help text Staging: rtl8192u: kconfig: Remove blank help text mmc: kconfig: Remove blank help text ...
2018-02-10mconsole_proc(): don't mess with file->f_posAl Viro1-1/+2
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2018-02-10Merge branch 'for-linus' of ↵Linus Torvalds2-2/+5
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs Pull misc vfs fixes from Al Viro. * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: seq_file: fix incomplete reset on read from zero offset kernfs: fix regression in kernfs_fop_write caused by wrong type
2018-02-10kconfig: remove const qualifier from sym_expand_string_value()Masahiro Yamada3-4/+4
This function returns realloc'ed memory, so the returned pointer must be passed to free() when done. So, 'const' qualifier is odd. It is allowed to modify the expanded string. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2018-02-10kconfig: add xrealloc() helperMasahiro Yamada6-5/+16
We already have xmalloc(), xcalloc(). Add xrealloc() as well to save tedious error handling. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2018-02-10platform/x86: mlx-platform: Add support for new 200G IB and Ethernet systemsVadim Pasternak1-0/+142
It adds support for new Mellanox system types of basic classes qmb7, sn34, sn37, containing systems QMB700 (40x200GbE InfiniBand switch), SN3700 (32x200GbE and 16x400GbE Ethernet switch) and SN3410 (6x400GbE plus 48x50GbE Ethernet switch). These are the Top of the Rack systems, equipped with Mellanox COM-Express carrier board and switch board with Mellanox Quantum device, which supports InfiniBand switching with 40X200G ports and line rate of up to HDR speed or with Mellanox Spectrum-2 device, which supports Ethernet switching with 32X200G ports line rate of up to HDR speed. Signed-off-by: Vadim Pasternak <vadimp@mellanox.com> Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
2018-02-10platform/x86: mlx-platform: Add support for new msn201x system typeVadim Pasternak1-0/+59
It adds support for new Mellanox system types of basic half unit size class msn201x, containing system MSN2010 (18x10GbE plus 4x4x25GbE) half and its derivatives. This is the Top of the Rack system, equipped with Mellanox Small Form Factor carrier board and switch board with Mellanox Spectrum device, which supports Ethernet switching with 32X100G ports line rate of up to EDR speed. Signed-off-by: Vadim Pasternak <vadimp@mellanox.com> Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
2018-02-10platform/x86: mlx-platform: Add support for new msn274x system typeVadim Pasternak1-0/+124
It adds support for new Mellanox system types of basic class msn274x, containing system MSN2740 (32x100GbE Ethernet switch with cost reduction) and its derivatives. These are the Top of the Rack system, equipped with Mellanox Small Form Factor carrier board and switch board with Mellanox Spectrum device, which supports Ethernet switching with 32X100G ports line rate of up to EDR speed. Signed-off-by: Vadim Pasternak <vadimp@mellanox.com> Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
2018-02-10Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netLinus Torvalds113-395/+1253
Pull networking fixes from David Miller: 1) Make allocations less aggressive in x_tables, from Minchal Hocko. 2) Fix netfilter flowtable Kconfig deps, from Pablo Neira Ayuso. 3) Fix connection loss problems in rtlwifi, from Larry Finger. 4) Correct DRAM dump length for some chips in ath10k driver, from Yu Wang. 5) Fix ABORT handling in rxrpc, from David Howells. 6) Add SPDX tags to Sun networking drivers, from Shannon Nelson. 7) Some ipv6 onlink handling fixes, from David Ahern. 8) Netem packet scheduler interval calcualtion fix from Md. Islam. 9) Don't put crypto buffers on-stack in rxrpc, from David Howells. 10) Fix handling of error non-delivery status in netlink multicast delivery over multiple namespaces, from Nicolas Dichtel. 11) Missing xdp flush in tuntap driver, from Jason Wang. 12) Synchonize RDS protocol netns/module teardown with rds object management, from Sowini Varadhan. 13) Add nospec annotations to mpls, from Dan Williams. 14) Fix SKB truesize handling in TIPC, from Hoang Le. 15) Interrupt masking fixes in stammc from Niklas Cassel. 16) Don't allow ptr_ring objects to be sized outside of kmalloc's limits, from Jason Wang. 17) Don't allow SCTP chunks to be built which will have a length exceeding the chunk header's 16-bit length field, from Alexey Kodanev. * git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (82 commits) ibmvnic: Remove skb->protocol checks in ibmvnic_xmit bpf: fix rlimit in reuseport net selftest sctp: verify size of a new chunk in _sctp_make_chunk() s390/qeth: fix SETIP command handling s390/qeth: fix underestimated count of buffer elements ptr_ring: try vmalloc() when kmalloc() fails ptr_ring: fail early if queue occupies more than KMALLOC_MAX_SIZE net: stmmac: remove redundant enable of PMT irq net: stmmac: rename GMAC_INT_DEFAULT_MASK for dwmac4 net: stmmac: discard disabled flags in interrupt status register ibmvnic: Reset long term map ID counter tools/libbpf: handle issues with bpf ELF objects containing .eh_frames selftests/bpf: add selftest that use test_libbpf_open selftests/bpf: add test program for loading BPF ELF files tools/libbpf: improve the pr_debug statements to contain section numbers bpf: Sync kernel ABI header with tooling header for bpf_common.h net: phy: fix phy_start to consider PHY_IGNORE_INTERRUPT net: thunder: change q_len's type to handle max ring size tipc: fix skb truesize/datasize ratio control net/sched: cls_u32: fix cls_u32 on filter replace ...
2018-02-10Merge tag 'nfs-for-4.16-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfsLinus Torvalds6-23/+36
Pull more NFS client updates from Trond Myklebust: "A few bugfixes and some small sunrpc latency/performance improvements before the merge window closes: Stable fixes: - fix an incorrect calculation of the RDMA send scatter gather element limit - fix an Oops when attempting to free resources after RDMA device removal Bugfixes: - SUNRPC: Ensure we always release the TCP socket in a timely fashion when the connection is shut down. - SUNRPC: Don't call __UDPX_INC_STATS() from a preemptible context Latency/Performance: - SUNRPC: Queue latency sensitive socket tasks to the less contended xprtiod queue - SUNRPC: Make the xprtiod workqueue unbounded. - SUNRPC: Make the rpciod workqueue unbounded" * tag 'nfs-for-4.16-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs: SUNRPC: Don't call __UDPX_INC_STATS() from a preemptible context fix parallelism for rpc tasks Make the xprtiod workqueue unbounded. SUNRPC: Queue latency-sensitive socket tasks to xprtiod SUNRPC: Ensure we always close the socket after a connection shuts down xprtrdma: Fix BUG after a device removal xprtrdma: Fix calculation of ri_max_send_sges
2018-02-10Merge branch 'for-next' of ↵Linus Torvalds15-389/+798
git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending Pull SCSI target updates from Nicholas Bellinger: "The highlights include: - numerous target-core-user improvements related to queue full and timeout handling. (MNC) - prevent target-core-user corruption when invalid data page is requested. (MNC) - add target-core device action configfs attributes to allow user-space to trigger events separate from existing attributes exposed to end-users. (MNC) - fix iscsi-target NULL pointer dereference 4.6+ regression in CHAP error path. (David Disseldorp) - avoid target-core backend UNMAP callbacks if range is zero. (Andrei Vagin) - fix a iscsi-target 4.14+ regression related multiple PDU logins, that was exposed due to removal of TCP prequeue support. (Florian Westphal + MNC) Also, there is a iser-target bug still being worked on for post -rc1 code to address a long standing issue resulting in persistent ib_post_send() failures, for RNICs with small max_send_sge" * 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (36 commits) iscsi-target: make sure to wake up sleeping login worker tcmu: Fix trailing semicolon tcmu: fix cmd user after free target: fix destroy device in target_configure_device tcmu: allow userspace to reset ring target core: add device action configfs files tcmu: fix error return code in tcmu_configure_device() target_core_user: add cmd id to broken ring message target: add SAM_STAT_BUSY sense reason tcmu: prevent corruption when invalid data page requested target: don't call an unmap callback if a range length is zero target/iscsi: avoid NULL dereference in CHAP auth error path cxgbit: call neigh_event_send() to update MAC address target: tcm_loop: Use seq_puts() in tcm_loop_show_info() target: tcm_loop: Delete an unnecessary return statement in tcm_loop_submission_work() target: tcm_loop: Delete two unnecessary variable initialisations in tcm_loop_issue_tmr() target: tcm_loop: Combine substrings for 26 messages target: tcm_loop: Improve a size determination in two functions target: tcm_loop: Delete an error message for a failed memory allocation in four functions sbp-target: Delete an error message for a failed memory allocation in three functions ...
2018-02-10Merge tag 'trace-v4.16-rc1' of ↵Linus Torvalds5-9/+54
git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace Pull tracing fixes from Steven Rostedt: "Al Viro discovered some breakage with the parsing of the set_ftrace_filter as well as the removing of function probes. This fixes the code with Al's suggestions. I also added a few selftests to test the broken cases such that they wont happen again" * tag 'trace-v4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace: selftests/ftrace: Add more tests for removing of function probes selftests/ftrace: Add some missing glob checks selftests/ftrace: Have reset_ftrace_filter handle multiple instances selftests/ftrace: Have reset_ftrace_filter handle modules tracing: Fix parsing of globs with a wildcard at the beginning ftrace: Remove incorrect setting of glob search field
2018-02-10Merge tag '4.16-minor-rc-SMB3-fixes' of git://git.samba.org/sfrench/cifs-2.6Linus Torvalds4-13/+130
Pull cifs fixes from Steve French: "There are a couple additional security fixes that are still being tested that are not in this set." * tag '4.16-minor-rc-SMB3-fixes' of git://git.samba.org/sfrench/cifs-2.6: Add missing structs and defines from recent SMB3.1.1 documentation address lock imbalance warnings in smbdirect.c cifs: silence compiler warnings showing up with gcc-8.0.0 Add some missing debug fields in server and tcon structs
2018-02-10Merge tag 'fbdev-v4.16-fix' of git://github.com/bzolnier/linuxLinus Torvalds4-0/+6
Pull fbdev fix from Bartlomiej Zolnierkiewicz: "Fix building of the omapfb driver (Tomi Valkeinen)" * tag 'fbdev-v4.16-fix' of git://github.com/bzolnier/linux: video: omapfb: fix missing #includes
2018-02-10Merge tag 'kvm-ppc-next-4.16-2' of ↵Radim Krčmář12-39/+251
git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc Second PPC KVM update for 4.16 Seven fixes that are either trivial or that address bugs that people are actually hitting. The main ones are: - Drop spinlocks before reading guest memory - Fix a bug causing corruption of VCPU state in PR KVM with preemption enabled - Make HPT resizing work on POWER9 - Add MMIO emulation for vector loads and stores, because guests now use these instructions in memcpy and similar routines.
2018-02-09Merge branch 'msr-bitmaps' of git://git.kernel.org/pub/scm/virt/kvm/kvmRadim Krčmář1-143/+164
This topic branch allocates separate MSR bitmaps for each VCPU. This is required for the IBRS enablement to choose, on a per-VM basis, whether to intercept the SPEC_CTRL and PRED_CMD MSRs; the IBRS enablement comes in through the tip tree.
2018-02-09ibmvnic: Remove skb->protocol checks in ibmvnic_xmitJohn Allen1-4/+1
Having these checks in ibmvnic_xmit causes problems with VLAN tagging and balance-alb/tlb bonding modes. The restriction they imposed can be removed. Signed-off-by: John Allen <jallen@linux.vnet.ibm.com> Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-02-09bpf: fix rlimit in reuseport net selftestDaniel Borkmann1-1/+20
Fix two issues in the reuseport_bpf selftests that were reported by Linaro CI: [...] + ./reuseport_bpf ---- IPv4 UDP ---- Testing EBPF mod 10... Reprograming, testing mod 5... ./reuseport_bpf: ebpf error. log: 0: (bf) r6 = r1 1: (20) r0 = *(u32 *)skb[0] 2: (97) r0 %= 10 3: (95) exit processed 4 insns : Operation not permitted + echo FAIL [...] ---- IPv4 TCP ---- Testing EBPF mod 10... ./reuseport_bpf: failed to bind send socket: Address already in use + echo FAIL [...] For the former adjust rlimit since this was the cause of failure for loading the BPF prog, and for the latter add SO_REUSEADDR. Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org> Link: https://bugs.linaro.org/show_bug.cgi?id=3502 Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-02-09sctp: verify size of a new chunk in _sctp_make_chunk()Alexey Kodanev1-1/+6
When SCTP makes INIT or INIT_ACK packet the total chunk length can exceed SCTP_MAX_CHUNK_LEN which leads to kernel panic when transmitting these packets, e.g. the crash on sending INIT_ACK: [ 597.804948] skbuff: skb_over_panic: text:00000000ffae06e4 len:120168 put:120156 head:000000007aa47635 data:00000000d991c2de tail:0x1d640 end:0xfec0 dev:<NULL> ... [ 597.976970] ------------[ cut here ]------------ [ 598.033408] kernel BUG at net/core/skbuff.c:104! [ 600.314841] Call Trace: [ 600.345829] <IRQ> [ 600.371639] ? sctp_packet_transmit+0x2095/0x26d0 [sctp] [ 600.436934] skb_put+0x16c/0x200 [ 600.477295] sctp_packet_transmit+0x2095/0x26d0 [sctp] [ 600.540630] ? sctp_packet_config+0x890/0x890 [sctp] [ 600.601781] ? __sctp_packet_append_chunk+0x3b4/0xd00 [sctp] [ 600.671356] ? sctp_cmp_addr_exact+0x3f/0x90 [sctp] [ 600.731482] sctp_outq_flush+0x663/0x30d0 [sctp] [ 600.788565] ? sctp_make_init+0xbf0/0xbf0 [sctp] [ 600.845555] ? sctp_check_transmitted+0x18f0/0x18f0 [sctp] [ 600.912945] ? sctp_outq_tail+0x631/0x9d0 [sctp] [ 600.969936] sctp_cmd_interpreter.isra.22+0x3be1/0x5cb0 [sctp] [ 601.041593] ? sctp_sf_do_5_1B_init+0x85f/0xc30 [sctp] [ 601.104837] ? sctp_generate_t1_cookie_event+0x20/0x20 [sctp] [ 601.175436] ? sctp_eat_data+0x1710/0x1710 [sctp] [ 601.233575] sctp_do_sm+0x182/0x560 [sctp] [ 601.284328] ? sctp_has_association+0x70/0x70 [sctp] [ 601.345586] ? sctp_rcv+0xef4/0x32f0 [sctp] [ 601.397478] ? sctp6_rcv+0xa/0x20 [sctp] ... Here the chunk size for INIT_ACK packet becomes too big, mostly because of the state cookie (INIT packet has large size with many address parameters), plus additional server parameters. Later this chunk causes the panic in skb_put_data(): skb_packet_transmit() sctp_packet_pack() skb_put_data(nskb, chunk->skb->data, chunk->skb->len); 'nskb' (head skb) was previously allocated with packet->size from u16 'chunk->chunk_hdr->length'. As suggested by Marcelo we should check the chunk's length in _sctp_make_chunk() before trying to allocate skb for it and discard a chunk if its size bigger than SCTP_MAX_CHUNK_LEN. Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leinter@gmail.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-02-09Merge branch 's390-qeth-fixes'David S. Miller2-7/+14
Julian Wiedmann says: ==================== s390/qeth: fixes 2018-02-09 please apply the following two qeth patches for 4.16 and stable. One restricts a command quirk to the intended commandd type, while the other fixes an off-by-one during data transmission that can cause qeth to build malformed buffer descriptors. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2018-02-09s390/qeth: fix SETIP command handlingJulian Wiedmann2-6/+13
send_control_data() applies some special handling to SETIP v4 IPA commands. But current code parses *all* command types for the SETIP command code. Limit the command code check to IPA commands. Fixes: 5b54e16f1a54 ("qeth: do not spin for SETIP ip assist command") Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit v1.2.3 (git 2.39.0) at 2024-11-15 13:06:58 +0300