summaryrefslogtreecommitdiff
AgeCommit message (Collapse)AuthorFilesLines
2023-07-17can: mcp251xfd: __mcp251xfd_chip_set_mode(): increase poll timeoutFedor Ross2-2/+9
The mcp251xfd controller needs an idle bus to enter 'Normal CAN 2.0 mode' or . The maximum length of a CAN frame is 736 bits (64 data bytes, CAN-FD, EFF mode, worst case bit stuffing and interframe spacing). For low bit rates like 10 kbit/s the arbitrarily chosen MCP251XFD_POLL_TIMEOUT_US of 1 ms is too small. Otherwise during polling for the CAN controller to enter 'Normal CAN 2.0 mode' the timeout limit is exceeded and the configuration fails with: | $ ip link set dev can1 up type can bitrate 10000 | [ 731.911072] mcp251xfd spi2.1 can1: Controller failed to enter mode CAN 2.0 Mode (6) and stays in Configuration Mode (4) (con=0x068b0760, osc=0x00000468). | [ 731.927192] mcp251xfd spi2.1 can1: CRC read error at address 0x0e0c (length=4, data=00 00 00 00, CRC=0x0000) retrying. | [ 731.938101] A link change request failed with some changes committed already. Interface can1 may have been left with an inconsistent configuration, please check. | RTNETLINK answers: Connection timed out Make MCP251XFD_POLL_TIMEOUT_US timeout calculation dynamic. Use maximum of 1ms and bit time of 1 full 64 data bytes CAN-FD frame in EFF mode, worst case bit stuffing and interframe spacing at the current bit rate. For easier backporting define the macro MCP251XFD_FRAME_LEN_MAX_BITS that holds the max frame length in bits, which is 736. This can be replaced by can_frame_bits(true, true, true, true, CANFD_MAX_DLEN) in a cleanup patch later. Fixes: 55e5b97f003e8 ("can: mcp25xxfd: add driver for Microchip MCP25xxFD SPI CAN") Signed-off-by: Fedor Ross <fedor.ross@ifm.com> Signed-off-by: Marek Vasut <marex@denx.de> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/all/20230717-mcp251xfd-fix-increase-poll-timeout-v5-1-06600f34c684@pengutronix.de Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2023-07-17iavf: fix reset task race with iavf_remove()Ahmed Zaki4-29/+16
The reset task is currently scheduled from the watchdog or adminq tasks. First, all direct calls to schedule the reset task are replaced with the iavf_schedule_reset(), which is modified to accept the flag showing the type of reset. To prevent the reset task from starting once iavf_remove() starts, we need to check the __IAVF_IN_REMOVE_TASK bit before we schedule it. This is now easily added to iavf_schedule_reset(). Finally, remove the check for IAVF_FLAG_RESET_NEEDED in the watchdog task. It is redundant since all callers who set the flag immediately schedules the reset task. Fixes: 3ccd54ef44eb ("iavf: Fix init state closure on remove") Fixes: 14756b2ae265 ("iavf: Fix __IAVF_RESETTING state usage") Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com> Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com> Tested-by: Rafal Romanowski <rafal.romanowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2023-07-17iavf: fix a deadlock caused by rtnl and driver's lock circular dependenciesAhmed Zaki3-32/+85
A driver's lock (crit_lock) is used to serialize all the driver's tasks. Lockdep, however, shows a circular dependency between rtnl and crit_lock. This happens when an ndo that already holds the rtnl requests the driver to reset, since the reset task (in some paths) tries to grab rtnl to either change real number of queues of update netdev features. [566.241851] ====================================================== [566.241893] WARNING: possible circular locking dependency detected [566.241936] 6.2.14-100.fc36.x86_64+debug #1 Tainted: G OE [566.241984] ------------------------------------------------------ [566.242025] repro.sh/2604 is trying to acquire lock: [566.242061] ffff9280fc5ceee8 (&adapter->crit_lock){+.+.}-{3:3}, at: iavf_close+0x3c/0x240 [iavf] [566.242167] but task is already holding lock: [566.242209] ffffffff9976d350 (rtnl_mutex){+.+.}-{3:3}, at: iavf_remove+0x6b5/0x730 [iavf] [566.242300] which lock already depends on the new lock. [566.242353] the existing dependency chain (in reverse order) is: [566.242401] -> #1 (rtnl_mutex){+.+.}-{3:3}: [566.242451] __mutex_lock+0xc1/0xbb0 [566.242489] iavf_init_interrupt_scheme+0x179/0x440 [iavf] [566.242560] iavf_watchdog_task+0x80b/0x1400 [iavf] [566.242627] process_one_work+0x2b3/0x560 [566.242663] worker_thread+0x4f/0x3a0 [566.242696] kthread+0xf2/0x120 [566.242730] ret_from_fork+0x29/0x50 [566.242763] -> #0 (&adapter->crit_lock){+.+.}-{3:3}: [566.242815] __lock_acquire+0x15ff/0x22b0 [566.242869] lock_acquire+0xd2/0x2c0 [566.242901] __mutex_lock+0xc1/0xbb0 [566.242934] iavf_close+0x3c/0x240 [iavf] [566.242997] __dev_close_many+0xac/0x120 [566.243036] dev_close_many+0x8b/0x140 [566.243071] unregister_netdevice_many_notify+0x165/0x7c0 [566.243116] unregister_netdevice_queue+0xd3/0x110 [566.243157] iavf_remove+0x6c1/0x730 [iavf] [566.243217] pci_device_remove+0x33/0xa0 [566.243257] device_release_driver_internal+0x1bc/0x240 [566.243299] pci_stop_bus_device+0x6c/0x90 [566.243338] pci_stop_and_remove_bus_device+0xe/0x20 [566.243380] pci_iov_remove_virtfn+0xd1/0x130 [566.243417] sriov_disable+0x34/0xe0 [566.243448] ice_free_vfs+0x2da/0x330 [ice] [566.244383] ice_sriov_configure+0x88/0xad0 [ice] [566.245353] sriov_numvfs_store+0xde/0x1d0 [566.246156] kernfs_fop_write_iter+0x15e/0x210 [566.246921] vfs_write+0x288/0x530 [566.247671] ksys_write+0x74/0xf0 [566.248408] do_syscall_64+0x58/0x80 [566.249145] entry_SYSCALL_64_after_hwframe+0x72/0xdc [566.249886] other info that might help us debug this: [566.252014] Possible unsafe locking scenario: [566.253432] CPU0 CPU1 [566.254118] ---- ---- [566.254800] lock(rtnl_mutex); [566.255514] lock(&adapter->crit_lock); [566.256233] lock(rtnl_mutex); [566.256897] lock(&adapter->crit_lock); [566.257388] *** DEADLOCK *** The deadlock can be triggered by a script that is continuously resetting the VF adapter while doing other operations requiring RTNL, e.g: while :; do ip link set $VF up ethtool --set-channels $VF combined 2 ip link set $VF down ip link set $VF up ethtool --set-channels $VF combined 4 ip link set $VF down done Any operation that triggers a reset can substitute "ethtool --set-channles" As a fix, add a new task "finish_config" that do all the work which needs rtnl lock. With the exception of iavf_remove(), all work that require rtnl should be called from this task. As for iavf_remove(), at the point where we need to call unregister_netdevice() (and grab rtnl_lock), we make sure the finish_config task is not running (cancel_work_sync()) to safely grab rtnl. Subsequent finish_config work cannot restart after that since the task is guarded by the __IAVF_IN_REMOVE_TASK bit in iavf_schedule_finish_config(). Fixes: 5ac49f3c2702 ("iavf: use mutexes for locking of critical sections") Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com> Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com> Tested-by: Rafal Romanowski <rafal.romanowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2023-07-17Revert "iavf: Do not restart Tx queues after reset task failure"Marcin Szycik1-15/+0
This reverts commit 08f1c147b7265245d67321585c68a27e990e0c4b. Netdev is no longer being detached during reset, so this fix can be reverted. We leave the removal of "hacky" IFF_UP flag update. Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com> Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com> Tested-by: Rafal Romanowski <rafal.romanowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2023-07-17Revert "iavf: Detach device during reset task"Marcin Szycik1-11/+2
This reverts commit aa626da947e9cd30c4cf727493903e1adbb2c0a0. Detaching device during reset was not fully fixing the rtnl locking issue, as there could be a situation where callback was already in progress before detaching netdev. Furthermore, detaching netdevice causes TX timeouts if traffic is running. To reproduce: ip netns exec ns1 iperf3 -c $PEER_IP -t 600 --logfile /dev/null & while :; do for i in 200 7000 400 5000 300 3000 ; do ip netns exec ns1 ip link set $VF1 mtu $i sleep 2 done sleep 10 done Currently, callbacks such as iavf_change_mtu() wait for the reset. If the reset fails to acquire the rtnl_lock, they schedule the netdev update for later while continuing the reset flow. Operations like MTU changes are performed under the rtnl_lock. Therefore, when the operation finishes, another callback that uses rtnl_lock can start. Signed-off-by: Dawid Wesierski <dawidx.wesierski@intel.com> Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com> Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com> Tested-by: Rafal Romanowski <rafal.romanowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2023-07-17iavf: Wait for reset in callbacks which trigger itMarcin Szycik4-17/+68
There was a fail when trying to add the interface to bonding right after changing the MTU on the interface. It was caused by bonding interface unable to open the interface due to interface being in __RESETTING state because of MTU change. Add new reset_waitqueue to indicate that reset has finished. Add waiting for reset to finish in callbacks which trigger hw reset: iavf_set_priv_flags(), iavf_change_mtu() and iavf_set_ringparam(). We use a 5000ms timeout period because on Hyper-V based systems, this operation takes around 3000-4000ms. In normal circumstances, it doesn't take more than 500ms to complete. Add a function iavf_wait_for_reset() to reuse waiting for reset code and use it also in iavf_set_channels(), which already waits for reset. We don't use error handling in iavf_set_channels() as this could cause the device to be in incorrect state if the reset was scheduled but hit timeout or the waitng function was interrupted by a signal. Fixes: 4e5e6b5d9d13 ("iavf: Fix return of set the new channel count") Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com> Co-developed-by: Dawid Wesierski <dawidx.wesierski@intel.com> Signed-off-by: Dawid Wesierski <dawidx.wesierski@intel.com> Signed-off-by: Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com> Signed-off-by: Kamil Maziarz <kamil.maziarz@intel.com> Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com> Tested-by: Rafal Romanowski <rafal.romanowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2023-07-17iavf: use internal state to free traffic IRQsAhmed Zaki1-3/+4
If the system tries to close the netdev while iavf_reset_task() is running, __LINK_STATE_START will be cleared and netif_running() will return false in iavf_reinit_interrupt_scheme(). This will result in iavf_free_traffic_irqs() not being called and a leak as follows: [7632.489326] remove_proc_entry: removing non-empty directory 'irq/999', leaking at least 'iavf-enp24s0f0v0-TxRx-0' [7632.490214] WARNING: CPU: 0 PID: 10 at fs/proc/generic.c:718 remove_proc_entry+0x19b/0x1b0 is shown when pci_disable_msix() is later called. Fix by using the internal adapter state. The traffic IRQs will always exist if state == __IAVF_RUNNING. Fixes: 5b36e8d04b44 ("i40evf: Enable VF to request an alternate queue allocation") Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com> Tested-by: Rafal Romanowski <rafal.romanowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2023-07-17iavf: Fix out-of-bounds when setting channels on removeDing Hui1-1/+1
If we set channels greater during iavf_remove(), and waiting reset done would be timeout, then returned with error but changed num_active_queues directly, that will lead to OOB like the following logs. Because the num_active_queues is greater than tx/rx_rings[] allocated actually. Reproducer: [root@host ~]# cat repro.sh #!/bin/bash pf_dbsf="0000:41:00.0" vf0_dbsf="0000:41:02.0" g_pids=() function do_set_numvf() { echo 2 >/sys/bus/pci/devices/${pf_dbsf}/sriov_numvfs sleep $((RANDOM%3+1)) echo 0 >/sys/bus/pci/devices/${pf_dbsf}/sriov_numvfs sleep $((RANDOM%3+1)) } function do_set_channel() { local nic=$(ls -1 --indicator-style=none /sys/bus/pci/devices/${vf0_dbsf}/net/) [ -z "$nic" ] && { sleep $((RANDOM%3)) ; return 1; } ifconfig $nic 192.168.18.5 netmask 255.255.255.0 ifconfig $nic up ethtool -L $nic combined 1 ethtool -L $nic combined 4 sleep $((RANDOM%3)) } function on_exit() { local pid for pid in "${g_pids[@]}"; do kill -0 "$pid" &>/dev/null && kill "$pid" &>/dev/null done g_pids=() } trap "on_exit; exit" EXIT while :; do do_set_numvf ; done & g_pids+=($!) while :; do do_set_channel ; done & g_pids+=($!) wait Result: [ 3506.152887] iavf 0000:41:02.0: Removing device [ 3510.400799] ================================================================== [ 3510.400820] BUG: KASAN: slab-out-of-bounds in iavf_free_all_tx_resources+0x156/0x160 [iavf] [ 3510.400823] Read of size 8 at addr ffff88b6f9311008 by task repro.sh/55536 [ 3510.400823] [ 3510.400830] CPU: 101 PID: 55536 Comm: repro.sh Kdump: loaded Tainted: G O --------- -t - 4.18.0 #1 [ 3510.400832] Hardware name: Powerleader PR2008AL/H12DSi-N6, BIOS 2.0 04/09/2021 [ 3510.400835] Call Trace: [ 3510.400851] dump_stack+0x71/0xab [ 3510.400860] print_address_description+0x6b/0x290 [ 3510.400865] ? iavf_free_all_tx_resources+0x156/0x160 [iavf] [ 3510.400868] kasan_report+0x14a/0x2b0 [ 3510.400873] iavf_free_all_tx_resources+0x156/0x160 [iavf] [ 3510.400880] iavf_remove+0x2b6/0xc70 [iavf] [ 3510.400884] ? iavf_free_all_rx_resources+0x160/0x160 [iavf] [ 3510.400891] ? wait_woken+0x1d0/0x1d0 [ 3510.400895] ? notifier_call_chain+0xc1/0x130 [ 3510.400903] pci_device_remove+0xa8/0x1f0 [ 3510.400910] device_release_driver_internal+0x1c6/0x460 [ 3510.400916] pci_stop_bus_device+0x101/0x150 [ 3510.400919] pci_stop_and_remove_bus_device+0xe/0x20 [ 3510.400924] pci_iov_remove_virtfn+0x187/0x420 [ 3510.400927] ? pci_iov_add_virtfn+0xe10/0xe10 [ 3510.400929] ? pci_get_subsys+0x90/0x90 [ 3510.400932] sriov_disable+0xed/0x3e0 [ 3510.400936] ? bus_find_device+0x12d/0x1a0 [ 3510.400953] i40e_free_vfs+0x754/0x1210 [i40e] [ 3510.400966] ? i40e_reset_all_vfs+0x880/0x880 [i40e] [ 3510.400968] ? pci_get_device+0x7c/0x90 [ 3510.400970] ? pci_get_subsys+0x90/0x90 [ 3510.400982] ? pci_vfs_assigned.part.7+0x144/0x210 [ 3510.400987] ? __mutex_lock_slowpath+0x10/0x10 [ 3510.400996] i40e_pci_sriov_configure+0x1fa/0x2e0 [i40e] [ 3510.401001] sriov_numvfs_store+0x214/0x290 [ 3510.401005] ? sriov_totalvfs_show+0x30/0x30 [ 3510.401007] ? __mutex_lock_slowpath+0x10/0x10 [ 3510.401011] ? __check_object_size+0x15a/0x350 [ 3510.401018] kernfs_fop_write+0x280/0x3f0 [ 3510.401022] vfs_write+0x145/0x440 [ 3510.401025] ksys_write+0xab/0x160 [ 3510.401028] ? __ia32_sys_read+0xb0/0xb0 [ 3510.401031] ? fput_many+0x1a/0x120 [ 3510.401032] ? filp_close+0xf0/0x130 [ 3510.401038] do_syscall_64+0xa0/0x370 [ 3510.401041] ? page_fault+0x8/0x30 [ 3510.401043] entry_SYSCALL_64_after_hwframe+0x65/0xca [ 3510.401073] RIP: 0033:0x7f3a9bb842c0 [ 3510.401079] Code: 73 01 c3 48 8b 0d d8 cb 2c 00 f7 d8 64 89 01 48 83 c8 ff c3 66 0f 1f 44 00 00 83 3d 89 24 2d 00 00 75 10 b8 01 00 00 00 0f 05 <48> 3d 01 f0 ff ff 73 31 c3 48 83 ec 08 e8 fe dd 01 00 48 89 04 24 [ 3510.401080] RSP: 002b:00007ffc05f1fe18 EFLAGS: 00000246 ORIG_RAX: 0000000000000001 [ 3510.401083] RAX: ffffffffffffffda RBX: 0000000000000002 RCX: 00007f3a9bb842c0 [ 3510.401085] RDX: 0000000000000002 RSI: 0000000002327408 RDI: 0000000000000001 [ 3510.401086] RBP: 0000000002327408 R08: 00007f3a9be53780 R09: 00007f3a9c8a4700 [ 3510.401086] R10: 0000000000000001 R11: 0000000000000246 R12: 0000000000000002 [ 3510.401087] R13: 0000000000000001 R14: 00007f3a9be52620 R15: 0000000000000001 [ 3510.401090] [ 3510.401093] Allocated by task 76795: [ 3510.401098] kasan_kmalloc+0xa6/0xd0 [ 3510.401099] __kmalloc+0xfb/0x200 [ 3510.401104] iavf_init_interrupt_scheme+0x26f/0x1310 [iavf] [ 3510.401108] iavf_watchdog_task+0x1d58/0x4050 [iavf] [ 3510.401114] process_one_work+0x56a/0x11f0 [ 3510.401115] worker_thread+0x8f/0xf40 [ 3510.401117] kthread+0x2a0/0x390 [ 3510.401119] ret_from_fork+0x1f/0x40 [ 3510.401122] 0xffffffffffffffff [ 3510.401123] In timeout handling, we should keep the original num_active_queues and reset num_req_queues to 0. Fixes: 4e5e6b5d9d13 ("iavf: Fix return of set the new channel count") Signed-off-by: Ding Hui <dinghui@sangfor.com.cn> Cc: Donglin Peng <pengdonglin@sangfor.com.cn> Cc: Huang Cun <huangcun@sangfor.com.cn> Reviewed-by: Leon Romanovsky <leonro@nvidia.com> Tested-by: Rafal Romanowski <rafal.romanowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2023-07-17iavf: Fix use-after-free in free_netdevDing Hui1-4/+1
We do netif_napi_add() for all allocated q_vectors[], but potentially do netif_napi_del() for part of them, then kfree q_vectors and leave invalid pointers at dev->napi_list. Reproducer: [root@host ~]# cat repro.sh #!/bin/bash pf_dbsf="0000:41:00.0" vf0_dbsf="0000:41:02.0" g_pids=() function do_set_numvf() { echo 2 >/sys/bus/pci/devices/${pf_dbsf}/sriov_numvfs sleep $((RANDOM%3+1)) echo 0 >/sys/bus/pci/devices/${pf_dbsf}/sriov_numvfs sleep $((RANDOM%3+1)) } function do_set_channel() { local nic=$(ls -1 --indicator-style=none /sys/bus/pci/devices/${vf0_dbsf}/net/) [ -z "$nic" ] && { sleep $((RANDOM%3)) ; return 1; } ifconfig $nic 192.168.18.5 netmask 255.255.255.0 ifconfig $nic up ethtool -L $nic combined 1 ethtool -L $nic combined 4 sleep $((RANDOM%3)) } function on_exit() { local pid for pid in "${g_pids[@]}"; do kill -0 "$pid" &>/dev/null && kill "$pid" &>/dev/null done g_pids=() } trap "on_exit; exit" EXIT while :; do do_set_numvf ; done & g_pids+=($!) while :; do do_set_channel ; done & g_pids+=($!) wait Result: [ 4093.900222] ================================================================== [ 4093.900230] BUG: KASAN: use-after-free in free_netdev+0x308/0x390 [ 4093.900232] Read of size 8 at addr ffff88b4dc145640 by task repro.sh/6699 [ 4093.900233] [ 4093.900236] CPU: 10 PID: 6699 Comm: repro.sh Kdump: loaded Tainted: G O --------- -t - 4.18.0 #1 [ 4093.900238] Hardware name: Powerleader PR2008AL/H12DSi-N6, BIOS 2.0 04/09/2021 [ 4093.900239] Call Trace: [ 4093.900244] dump_stack+0x71/0xab [ 4093.900249] print_address_description+0x6b/0x290 [ 4093.900251] ? free_netdev+0x308/0x390 [ 4093.900252] kasan_report+0x14a/0x2b0 [ 4093.900254] free_netdev+0x308/0x390 [ 4093.900261] iavf_remove+0x825/0xd20 [iavf] [ 4093.900265] pci_device_remove+0xa8/0x1f0 [ 4093.900268] device_release_driver_internal+0x1c6/0x460 [ 4093.900271] pci_stop_bus_device+0x101/0x150 [ 4093.900273] pci_stop_and_remove_bus_device+0xe/0x20 [ 4093.900275] pci_iov_remove_virtfn+0x187/0x420 [ 4093.900277] ? pci_iov_add_virtfn+0xe10/0xe10 [ 4093.900278] ? pci_get_subsys+0x90/0x90 [ 4093.900280] sriov_disable+0xed/0x3e0 [ 4093.900282] ? bus_find_device+0x12d/0x1a0 [ 4093.900290] i40e_free_vfs+0x754/0x1210 [i40e] [ 4093.900298] ? i40e_reset_all_vfs+0x880/0x880 [i40e] [ 4093.900299] ? pci_get_device+0x7c/0x90 [ 4093.900300] ? pci_get_subsys+0x90/0x90 [ 4093.900306] ? pci_vfs_assigned.part.7+0x144/0x210 [ 4093.900309] ? __mutex_lock_slowpath+0x10/0x10 [ 4093.900315] i40e_pci_sriov_configure+0x1fa/0x2e0 [i40e] [ 4093.900318] sriov_numvfs_store+0x214/0x290 [ 4093.900320] ? sriov_totalvfs_show+0x30/0x30 [ 4093.900321] ? __mutex_lock_slowpath+0x10/0x10 [ 4093.900323] ? __check_object_size+0x15a/0x350 [ 4093.900326] kernfs_fop_write+0x280/0x3f0 [ 4093.900329] vfs_write+0x145/0x440 [ 4093.900330] ksys_write+0xab/0x160 [ 4093.900332] ? __ia32_sys_read+0xb0/0xb0 [ 4093.900334] ? fput_many+0x1a/0x120 [ 4093.900335] ? filp_close+0xf0/0x130 [ 4093.900338] do_syscall_64+0xa0/0x370 [ 4093.900339] ? page_fault+0x8/0x30 [ 4093.900341] entry_SYSCALL_64_after_hwframe+0x65/0xca [ 4093.900357] RIP: 0033:0x7f16ad4d22c0 [ 4093.900359] Code: 73 01 c3 48 8b 0d d8 cb 2c 00 f7 d8 64 89 01 48 83 c8 ff c3 66 0f 1f 44 00 00 83 3d 89 24 2d 00 00 75 10 b8 01 00 00 00 0f 05 <48> 3d 01 f0 ff ff 73 31 c3 48 83 ec 08 e8 fe dd 01 00 48 89 04 24 [ 4093.900360] RSP: 002b:00007ffd6491b7f8 EFLAGS: 00000246 ORIG_RAX: 0000000000000001 [ 4093.900362] RAX: ffffffffffffffda RBX: 0000000000000002 RCX: 00007f16ad4d22c0 [ 4093.900363] RDX: 0000000000000002 RSI: 0000000001a41408 RDI: 0000000000000001 [ 4093.900364] RBP: 0000000001a41408 R08: 00007f16ad7a1780 R09: 00007f16ae1f2700 [ 4093.900364] R10: 0000000000000001 R11: 0000000000000246 R12: 0000000000000002 [ 4093.900365] R13: 0000000000000001 R14: 00007f16ad7a0620 R15: 0000000000000001 [ 4093.900367] [ 4093.900368] Allocated by task 820: [ 4093.900371] kasan_kmalloc+0xa6/0xd0 [ 4093.900373] __kmalloc+0xfb/0x200 [ 4093.900376] iavf_init_interrupt_scheme+0x63b/0x1320 [iavf] [ 4093.900380] iavf_watchdog_task+0x3d51/0x52c0 [iavf] [ 4093.900382] process_one_work+0x56a/0x11f0 [ 4093.900383] worker_thread+0x8f/0xf40 [ 4093.900384] kthread+0x2a0/0x390 [ 4093.900385] ret_from_fork+0x1f/0x40 [ 4093.900387] 0xffffffffffffffff [ 4093.900387] [ 4093.900388] Freed by task 6699: [ 4093.900390] __kasan_slab_free+0x137/0x190 [ 4093.900391] kfree+0x8b/0x1b0 [ 4093.900394] iavf_free_q_vectors+0x11d/0x1a0 [iavf] [ 4093.900397] iavf_remove+0x35a/0xd20 [iavf] [ 4093.900399] pci_device_remove+0xa8/0x1f0 [ 4093.900400] device_release_driver_internal+0x1c6/0x460 [ 4093.900401] pci_stop_bus_device+0x101/0x150 [ 4093.900402] pci_stop_and_remove_bus_device+0xe/0x20 [ 4093.900403] pci_iov_remove_virtfn+0x187/0x420 [ 4093.900404] sriov_disable+0xed/0x3e0 [ 4093.900409] i40e_free_vfs+0x754/0x1210 [i40e] [ 4093.900415] i40e_pci_sriov_configure+0x1fa/0x2e0 [i40e] [ 4093.900416] sriov_numvfs_store+0x214/0x290 [ 4093.900417] kernfs_fop_write+0x280/0x3f0 [ 4093.900418] vfs_write+0x145/0x440 [ 4093.900419] ksys_write+0xab/0x160 [ 4093.900420] do_syscall_64+0xa0/0x370 [ 4093.900421] entry_SYSCALL_64_after_hwframe+0x65/0xca [ 4093.900422] 0xffffffffffffffff [ 4093.900422] [ 4093.900424] The buggy address belongs to the object at ffff88b4dc144200 which belongs to the cache kmalloc-8k of size 8192 [ 4093.900425] The buggy address is located 5184 bytes inside of 8192-byte region [ffff88b4dc144200, ffff88b4dc146200) [ 4093.900425] The buggy address belongs to the page: [ 4093.900427] page:ffffea00d3705000 refcount:1 mapcount:0 mapping:ffff88bf04415c80 index:0x0 compound_mapcount: 0 [ 4093.900430] flags: 0x10000000008100(slab|head) [ 4093.900433] raw: 0010000000008100 dead000000000100 dead000000000200 ffff88bf04415c80 [ 4093.900434] raw: 0000000000000000 0000000000030003 00000001ffffffff 0000000000000000 [ 4093.900434] page dumped because: kasan: bad access detected [ 4093.900435] [ 4093.900435] Memory state around the buggy address: [ 4093.900436] ffff88b4dc145500: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb [ 4093.900437] ffff88b4dc145580: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb [ 4093.900438] >ffff88b4dc145600: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb [ 4093.900438] ^ [ 4093.900439] ffff88b4dc145680: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb [ 4093.900440] ffff88b4dc145700: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb [ 4093.900440] ================================================================== Although the patch #2 (of 2) can avoid the issue triggered by this repro.sh, there still are other potential risks that if num_active_queues is changed to less than allocated q_vectors[] by unexpected, the mismatched netif_napi_add/del() can also cause UAF. Since we actually call netif_napi_add() for all allocated q_vectors unconditionally in iavf_alloc_q_vectors(), so we should fix it by letting netif_napi_del() match to netif_napi_add(). Fixes: 5eae00c57f5e ("i40evf: main driver core") Signed-off-by: Ding Hui <dinghui@sangfor.com.cn> Cc: Donglin Peng <pengdonglin@sangfor.com.cn> Cc: Huang Cun <huangcun@sangfor.com.cn> Reviewed-by: Simon Horman <simon.horman@corigine.com> Reviewed-by: Madhu Chittim <madhu.chittim@intel.com> Reviewed-by: Leon Romanovsky <leonro@nvidia.com> Tested-by: Rafal Romanowski <rafal.romanowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2023-07-17Merge patch series "can: gs_usb: fix time stamp counter initialization"Marc Kleine-Budde1-56/+74
Marc Kleine-Budde <mkl@pengutronix.de> says: During testing I noticed a crash if unloading/loading the gs_usb driver during high CAN bus load. The current version of the candlelight firmware doesn't flush the queues of the received CAN frames during the reset command. This leads to a crash if hardware timestamps are enabled, and an URB from the device is received before the cycle counter/time counter infrastructure has been setup. First clean up then error handling in gs_can_open(). Then, fix the problem by converting the cycle counter/time counter infrastructure from a per-channel to per-device and set it up before submitting RX-URBs to the USB stack. Link: https://lore.kernel.org/all/20230716-gs_usb-fix-time-stamp-counter-v1-0-9017cefcd9d5@pengutronix.de Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2023-07-17can: gs_usb: fix time stamp counter initializationMarc Kleine-Budde1-48/+53
If the gs_usb device driver is unloaded (or unbound) before the interface is shut down, the USB stack first calls the struct usb_driver::disconnect and then the struct net_device_ops::ndo_stop callback. In gs_usb_disconnect() all pending bulk URBs are killed, i.e. no more RX'ed CAN frames are send from the USB device to the host. Later in gs_can_close() a reset control message is send to each CAN channel to remove the controller from the CAN bus. In this race window the USB device can still receive CAN frames from the bus and internally queue them to be send to the host. At least in the current version of the candlelight firmware, the queue of received CAN frames is not emptied during the reset command. After loading (or binding) the gs_usb driver, new URBs are submitted during the struct net_device_ops::ndo_open callback and the candlelight firmware starts sending its already queued CAN frames to the host. However, this scenario was not considered when implementing the hardware timestamp function. The cycle counter/time counter infrastructure is set up (gs_usb_timestamp_init()) after the USBs are submitted, resulting in a NULL pointer dereference if timecounter_cyc2time() (via the call chain: gs_usb_receive_bulk_callback() -> gs_usb_set_timestamp() -> gs_usb_skb_set_timestamp()) is called too early. Move the gs_usb_timestamp_init() function before the URBs are submitted to fix this problem. For a comprehensive solution, we need to consider gs_usb devices with more than 1 channel. The cycle counter/time counter infrastructure is setup per channel, but the RX URBs are per device. Once gs_can_open() of _a_ channel has been called, and URBs have been submitted, the gs_usb_receive_bulk_callback() can be called for _all_ available channels, even for channels that are not running, yet. As cycle counter/time counter has not set up, this will again lead to a NULL pointer dereference. Convert the cycle counter/time counter from a "per channel" to a "per device" functionality. Also set it up, before submitting any URBs to the device. Further in gs_usb_receive_bulk_callback(), don't process any URBs for not started CAN channels, only resubmit the URB. Fixes: 45dfa45f52e6 ("can: gs_usb: add RX and TX hardware timestamp support") Closes: https://github.com/candle-usb/candleLight_fw/issues/137#issuecomment-1623532076 Cc: stable@vger.kernel.org Cc: John Whittington <git@jbrengineering.co.uk> Link: https://lore.kernel.org/all/20230716-gs_usb-fix-time-stamp-counter-v1-2-9017cefcd9d5@pengutronix.de Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2023-07-17can: gs_usb: gs_can_open(): improve error handlingMarc Kleine-Budde1-9/+22
The gs_usb driver handles USB devices with more than 1 CAN channel. The RX path for all channels share the same bulk endpoint (the transmitted bulk data encodes the channel number). These per-device resources are allocated and submitted by the first opened channel. During this allocation, the resources are either released immediately in case of a failure or the URBs are anchored. All anchored URBs are finally killed with gs_usb_disconnect(). Currently, gs_can_open() returns with an error if the allocation of a URB or a buffer fails. However, if usb_submit_urb() fails, the driver continues with the URBs submitted so far, even if no URBs were successfully submitted. Treat every error as fatal and free all allocated resources immediately. Switch to goto-style error handling, to prepare the driver for more per-device resource allocation. Cc: stable@vger.kernel.org Cc: John Whittington <git@jbrengineering.co.uk> Link: https://lore.kernel.org/all/20230716-gs_usb-fix-time-stamp-counter-v1-1-9017cefcd9d5@pengutronix.de Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2023-07-17can: bcm: Fix UAF in bcm_proc_show()YueHaibing1-6/+6
BUG: KASAN: slab-use-after-free in bcm_proc_show+0x969/0xa80 Read of size 8 at addr ffff888155846230 by task cat/7862 CPU: 1 PID: 7862 Comm: cat Not tainted 6.5.0-rc1-00153-gc8746099c197 #230 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.15.0-1 04/01/2014 Call Trace: <TASK> dump_stack_lvl+0xd5/0x150 print_report+0xc1/0x5e0 kasan_report+0xba/0xf0 bcm_proc_show+0x969/0xa80 seq_read_iter+0x4f6/0x1260 seq_read+0x165/0x210 proc_reg_read+0x227/0x300 vfs_read+0x1d5/0x8d0 ksys_read+0x11e/0x240 do_syscall_64+0x35/0xb0 entry_SYSCALL_64_after_hwframe+0x63/0xcd Allocated by task 7846: kasan_save_stack+0x1e/0x40 kasan_set_track+0x21/0x30 __kasan_kmalloc+0x9e/0xa0 bcm_sendmsg+0x264b/0x44e0 sock_sendmsg+0xda/0x180 ____sys_sendmsg+0x735/0x920 ___sys_sendmsg+0x11d/0x1b0 __sys_sendmsg+0xfa/0x1d0 do_syscall_64+0x35/0xb0 entry_SYSCALL_64_after_hwframe+0x63/0xcd Freed by task 7846: kasan_save_stack+0x1e/0x40 kasan_set_track+0x21/0x30 kasan_save_free_info+0x27/0x40 ____kasan_slab_free+0x161/0x1c0 slab_free_freelist_hook+0x119/0x220 __kmem_cache_free+0xb4/0x2e0 rcu_core+0x809/0x1bd0 bcm_op is freed before procfs entry be removed in bcm_release(), this lead to bcm_proc_show() may read the freed bcm_op. Fixes: ffd980f976e7 ("[CAN]: Add broadcast manager (bcm) protocol") Signed-off-by: YueHaibing <yuehaibing@huawei.com> Reviewed-by: Oliver Hartkopp <socketcan@hartkopp.net> Acked-by: Oliver Hartkopp <socketcan@hartkopp.net> Link: https://lore.kernel.org/all/20230715092543.15548-1-yuehaibing@huawei.com Cc: stable@vger.kernel.org Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2023-07-17can: raw: fix receiver memory leakZiyang Xuan1-33/+24
Got kmemleak errors with the following ltp can_filter testcase: for ((i=1; i<=100; i++)) do ./can_filter & sleep 0.1 done ============================================================== [<00000000db4a4943>] can_rx_register+0x147/0x360 [can] [<00000000a289549d>] raw_setsockopt+0x5ef/0x853 [can_raw] [<000000006d3d9ebd>] __sys_setsockopt+0x173/0x2c0 [<00000000407dbfec>] __x64_sys_setsockopt+0x61/0x70 [<00000000fd468496>] do_syscall_64+0x33/0x40 [<00000000b7e47d51>] entry_SYSCALL_64_after_hwframe+0x61/0xc6 It's a bug in the concurrent scenario of unregister_netdevice_many() and raw_release() as following: cpu0 cpu1 unregister_netdevice_many(can_dev) unlist_netdevice(can_dev) // dev_get_by_index() return NULL after this net_set_todo(can_dev) raw_release(can_socket) dev = dev_get_by_index(, ro->ifindex); // dev == NULL if (dev) { // receivers in dev_rcv_lists not free because dev is NULL raw_disable_allfilters(, dev, ); dev_put(dev); } ... ro->bound = 0; ... call_netdevice_notifiers(NETDEV_UNREGISTER, ) raw_notify(, NETDEV_UNREGISTER, ) if (ro->bound) // invalid because ro->bound has been set 0 raw_disable_allfilters(, dev, ); // receivers in dev_rcv_lists will never be freed Add a net_device pointer member in struct raw_sock to record bound can_dev, and use rtnl_lock to serialize raw_socket members between raw_bind(), raw_release(), raw_setsockopt() and raw_notify(). Use ro->dev to decide whether to free receivers in dev_rcv_lists. Fixes: 8d0caedb7596 ("can: bcm/raw/isotp: use per module netdevice notifier") Reviewed-by: Oliver Hartkopp <socketcan@hartkopp.net> Acked-by: Oliver Hartkopp <socketcan@hartkopp.net> Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com> Link: https://lore.kernel.org/all/20230711011737.1969582-1-william.xuanziyang@huawei.com Cc: stable@vger.kernel.org Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2023-07-17r8169: fix ASPM-related problem for chip version 42 and 43Heiner Kallweit1-0/+7
Referenced commit missed that for chip versions 42 and 43 ASPM remained disabled in the respective rtl_hw_start_...() routines. This resulted in problems as described in the referenced bug ticket. Therefore re-instantiate the previous logic. Fixes: 5fc3f6c90cca ("r8169: consolidate disabling ASPM before EPHY access") Closes: https://bugzilla.kernel.org/show_bug.cgi?id=217635 Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2023-07-17net: dsa: microchip: correct KSZ8795 static MAC table accessTristram Ha3-5/+18
The KSZ8795 driver code was modified to use on KSZ8863/73, which has different register definitions. Some of the new KSZ8795 register information are wrong compared to previous code. KSZ8795 also behaves differently in that the STATIC_MAC_TABLE_USE_FID and STATIC_MAC_TABLE_FID bits are off by 1 when doing MAC table reading than writing. To compensate that a special code was added to shift the register value by 1 before applying those bits. This is wrong when the code is running on KSZ8863, so this special code is only executed when KSZ8795 is detected. Fixes: 4b20a07e103f ("net: dsa: microchip: ksz8795: add support for ksz88xx chips") Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com> Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com> Reviewed-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2023-07-17Merge branch 'sched-fixes'David S. Miller4-138/+143
Victor Nogueira says: ==================== net: sched: Fixes for classifiers Four different classifiers (bpf, u32, matchall, and flower) are calling tcf_bind_filter in their callbacks, but arent't undoing it by calling tcf_unbind_filter if their was an error after binding. This patch set fixes all this by calling tcf_unbind_filter in such cases. This set also undoes a refcount decrement in cls_u32 when an update fails under specific conditions which are described in patch #3. v1 -> v2: * Remove blank line after fixes tag * Fix reverse xmas tree issues pointed out by Simon v2 -> v3: * Inline functions cls_bpf_set_parms and fl_set_parms to avoid adding yet another parameter (and a return value at it) to them. * Remove similar fixes for u32 and matchall, which will be sent soon, once we find a way to do the fixes without adding a return parameter to their set_parms functions. v3 -> v4: * Inline mall_set_parms to avoid adding yet another parameter. * Remove set_flags parameter from u32_set_parms and create a separate function for calling tcf_bind_filter and tcf_unbind_filter in case of failure. * Change cover letter title to also encompass refcnt fix for u32 v4 -> v5: * Change back tag to net ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2023-07-17net: sched: cls_flower: Undo tcf_bind_filter in case of an errorVictor Nogueira1-52/+47
If TCA_FLOWER_CLASSID is specified in the netlink message, the code will call tcf_bind_filter. However, if any error occurs after that, the code should undo this by calling tcf_unbind_filter. Fixes: 77b9900ef53a ("tc: introduce Flower classifier") Signed-off-by: Victor Nogueira <victor@mojatatu.com> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Reviewed-by: Pedro Tammela <pctammela@mojatatu.com> Reviewed-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2023-07-17net: sched: cls_bpf: Undo tcf_bind_filter in case of an errorVictor Nogueira1-52/+47
If cls_bpf_offload errors out, we must also undo tcf_bind_filter that was done before the error. Fix that by calling tcf_unbind_filter in errout_parms. Fixes: eadb41489fd2 ("net: cls_bpf: add support for marking filters as hardware-only") Signed-off-by: Victor Nogueira <victor@mojatatu.com> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Reviewed-by: Pedro Tammela <pctammela@mojatatu.com> Reviewed-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2023-07-17net: sched: cls_u32: Undo refcount decrement in case update failedVictor Nogueira1-0/+7
In the case of an update, when TCA_U32_LINK is set, u32_set_parms will decrement the refcount of the ht_down (struct tc_u_hnode) pointer present in the older u32 filter which we are replacing. However, if u32_replace_hw_knode errors out, the update command fails and that ht_down pointer continues decremented. To fix that, when u32_replace_hw_knode fails, check if ht_down's refcount was decremented and undo the decrement. Fixes: d34e3e181395 ("net: cls_u32: Add support for skip-sw flag to tc u32 classifier.") Signed-off-by: Victor Nogueira <victor@mojatatu.com> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Reviewed-by: Pedro Tammela <pctammela@mojatatu.com> Reviewed-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2023-07-17net: sched: cls_u32: Undo tcf_bind_filter if u32_replace_hw_knodeVictor Nogueira1-11/+30
When u32_replace_hw_knode fails, we need to undo the tcf_bind_filter operation done at u32_set_parms. Fixes: d34e3e181395 ("net: cls_u32: Add support for skip-sw flag to tc u32 classifier.") Signed-off-by: Victor Nogueira <victor@mojatatu.com> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Reviewed-by: Pedro Tammela <pctammela@mojatatu.com> Reviewed-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2023-07-17net: sched: cls_matchall: Undo tcf_bind_filter in case of failure after ↵Victor Nogueira1-23/+12
mall_set_parms In case an error occurred after mall_set_parms executed successfully, we must undo the tcf_bind_filter call it issues. Fix that by calling tcf_unbind_filter in err_replace_hw_filter label. Fixes: ec2507d2a306 ("net/sched: cls_matchall: Fix error path") Signed-off-by: Victor Nogueira <victor@mojatatu.com> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Reviewed-by: Pedro Tammela <pctammela@mojatatu.com> Reviewed-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2023-07-15Merge branch 'net-fix-kernel-doc-problems-in-include-net'Jakub Kicinski9-22/+29
Randy Dunlap says: ==================== net: fix kernel-doc problems in include/net/ Fix many (but not all) kernel-doc warnings in include/net/. [PATCH v2 net 1/9] net: bonding: remove kernel-doc comment marker [PATCH v2 net 2/9] net: cfg802154: fix kernel-doc notation warnings [PATCH v2 net 3/9] codel: fix kernel-doc notation warnings [PATCH v2 net 4/9] devlink: fix kernel-doc notation warnings [PATCH v2 net 5/9] inet: frags: remove kernel-doc comment marker [PATCH v2 net 6/9] net: llc: fix kernel-doc notation warnings [PATCH v2 net 7/9] net: NSH: fix kernel-doc notation warning [PATCH v2 net 8/9] pie: fix kernel-doc notation warning [PATCH v2 net 9/9] rsi: remove kernel-doc comment marker ==================== Link: https://lore.kernel.org/r/20230714045127.18752-1-rdunlap@infradead.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2023-07-15rsi: remove kernel-doc comment markerRandy Dunlap1-1/+1
Change an errant kernel-doc comment marker (/**) to a regular comment to prevent a kernel-doc warning. rsi_91x.h:3: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst * Copyright (c) 2017 Redpine Signals Inc. Fixes: 4c10d56a76bb ("rsi: add header file rsi_91x") Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Cc: Prameela Rani Garnepudi <prameela.j04cs@gmail.com> Cc: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com> Acked-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20230714045127.18752-10-rdunlap@infradead.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2023-07-15pie: fix kernel-doc notation warningRandy Dunlap1-1/+1
Spell a struct member's name correctly to prevent a kernel-doc warning. pie.h:38: warning: Function parameter or member 'tupdate' not described in 'pie_params' Fixes: b42a3d7c7cff ("pie: improve comments and commenting style") Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Cc: Leslie Monis <lesliemonis@gmail.com> Cc: "Mohit P. Tahiliani" <tahiliani@nitk.edu.in> Cc: Gautam Ramakrishnan <gautamramk@gmail.com> Cc: Jamal Hadi Salim <jhs@mojatatu.com> Cc: Cong Wang <xiyou.wangcong@gmail.com> Cc: Jiri Pirko <jiri@resnulli.us> Link: https://lore.kernel.org/r/20230714045127.18752-9-rdunlap@infradead.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2023-07-15net: NSH: fix kernel-doc notation warningRandy Dunlap1-1/+1
Use the struct member's name and the correct format to prevent a kernel-doc warning. nsh.h:200: warning: Function parameter or member 'context' not described in 'nsh_md1_ctx' Fixes: 1f0b7744c505 ("net: add NSH header structures and helpers") Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Cc: Jiri Benc <jbenc@redhat.com> Link: https://lore.kernel.org/r/20230714045127.18752-8-rdunlap@infradead.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2023-07-15net: llc: fix kernel-doc notation warningsRandy Dunlap1-2/+4
Use the corrent function parameter name or format to prevent kernel-doc warnings. Add 2 function parameter descriptions to prevent kernel-doc warnings. llc_pdu.h:278: warning: Function parameter or member 'da' not described in 'llc_pdu_decode_da' llc_pdu.h:278: warning: Excess function parameter 'sa' description in 'llc_pdu_decode_da' llc_pdu.h:330: warning: Function parameter or member 'skb' not described in 'llc_pdu_init_as_test_cmd' llc_pdu.h:379: warning: Function parameter or member 'svcs_supported' not described in 'llc_pdu_init_as_xid_cmd' llc_pdu.h:379: warning: Function parameter or member 'rx_window' not described in 'llc_pdu_init_as_xid_cmd' Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Link: https://lore.kernel.org/r/20230714045127.18752-7-rdunlap@infradead.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2023-07-15inet: frags: eliminate kernel-doc warningRandy Dunlap1-1/+1
Modify the anonymous enum kernel-doc content so that it doesn't cause a kernel-doc warning. inet_frag.h:33: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst Fixes: 1ab1934ed80a ("inet: frags: enum the flag definitions and add descriptions") Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Cc: Nikolay Aleksandrov <razor@blackwall.org> Link: https://lore.kernel.org/r/20230714045127.18752-6-rdunlap@infradead.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2023-07-15devlink: fix kernel-doc notation warningsRandy Dunlap1-12/+16
Spell function or struct member names correctly. Use ':' instead of '-' for struct member entries. Mark one field as private in kernel-doc. Add a few entries that were missing. Fix a typo. These changes prevent kernel-doc warnings: devlink.h:252: warning: Function parameter or member 'field_id' not described in 'devlink_dpipe_match' devlink.h:267: warning: Function parameter or member 'field_id' not described in 'devlink_dpipe_action' devlink.h:310: warning: Function parameter or member 'match_values_count' not described in 'devlink_dpipe_entry' devlink.h:355: warning: Function parameter or member 'list' not described in 'devlink_dpipe_table' devlink.h:374: warning: Function parameter or member 'actions_dump' not described in 'devlink_dpipe_table_ops' devlink.h:374: warning: Function parameter or member 'matches_dump' not described in 'devlink_dpipe_table_ops' devlink.h:374: warning: Function parameter or member 'entries_dump' not described in 'devlink_dpipe_table_ops' devlink.h:374: warning: Function parameter or member 'counters_set_update' not described in 'devlink_dpipe_table_ops' devlink.h:374: warning: Function parameter or member 'size_get' not described in 'devlink_dpipe_table_ops' devlink.h:384: warning: Function parameter or member 'headers' not described in 'devlink_dpipe_headers' devlink.h:384: warning: Function parameter or member 'headers_count' not described in 'devlink_dpipe_headers' devlink.h:398: warning: Function parameter or member 'unit' not described in 'devlink_resource_size_params' devlink.h:487: warning: Function parameter or member 'id' not described in 'devlink_param' devlink.h:645: warning: Function parameter or member 'overwrite_mask' not described in 'devlink_flash_update_params' Fixes: 1555d204e743 ("devlink: Support for pipeline debug (dpipe)") Fixes: d9f9b9a4d05f ("devlink: Add support for resource abstraction") Fixes: eabaef1896bc ("devlink: Add devlink_param register and unregister") Fixes: 5d5b4128c4ca ("devlink: introduce flash update overwrite mask") Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Cc: Jiri Pirko <jiri@resnulli.us> Cc: Moshe Shemesh <moshe@mellanox.com> Cc: Jacob Keller <jacob.e.keller@intel.com> Link: https://lore.kernel.org/r/20230714045127.18752-5-rdunlap@infradead.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2023-07-15codel: fix kernel-doc notation warningsRandy Dunlap1-2/+2
Use '@' before the struct member names in kernel-doc notation to prevent kernel-doc warnings. codel.h:158: warning: Function parameter or member 'ecn_mark' not described in 'codel_stats' codel.h:158: warning: Function parameter or member 'ce_mark' not described in 'codel_stats' Fixes: 76e3cc126bb2 ("codel: Controlled Delay AQM") Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Cc: Jamal Hadi Salim <jhs@mojatatu.com> Cc: Cong Wang <xiyou.wangcong@gmail.com> Cc: Jiri Pirko <jiri@resnulli.us> Cc: Dave Taht <dave.taht@bufferbloat.net> Link: https://lore.kernel.org/r/20230714045127.18752-4-rdunlap@infradead.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2023-07-15net: cfg802154: fix kernel-doc notation warningsRandy Dunlap1-1/+2
Add an enum heading to the kernel-doc comments to prevent kernel-doc warnings. cfg802154.h:174: warning: Cannot understand * @WPAN_PHY_FLAG_TRANSMIT_POWER: Indicates that transceiver will support on line 174 - I thought it was a doc line cfg802154.h:192: warning: Enum value 'WPAN_PHY_FLAG_TXPOWER' not described in enum 'wpan_phy_flags' cfg802154.h:192: warning: Excess enum value 'WPAN_PHY_FLAG_TRANSMIT_POWER' description in 'wpan_phy_flags' Fixes: edea8f7c75ec ("cfg802154: introduce wpan phy flags") Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Cc: Alexander Aring <alex.aring@gmail.com> Cc: Stefan Schmidt <stefan@datenfreihafen.org> Cc: Marcel Holtmann <marcel@holtmann.org> Acked-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/r/20230714045127.18752-3-rdunlap@infradead.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2023-07-15net: bonding: remove kernel-doc comment markerRandy Dunlap1-1/+1
Change an errant kernel-doc comment marker (/**) to a regular comment to prevent a kernel-doc warning. bonding.h:282: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst * Returns NULL if the net_device does not belong to any of the bond's slaves Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Cc: Jay Vosburgh <j.vosburgh@gmail.com> Cc: Andy Gospodarek <andy@greyhouse.net> Link: https://lore.kernel.org/r/20230714045127.18752-2-rdunlap@infradead.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2023-07-14ice: prevent NULL pointer deref during reloadMichal Swiatkowski3-4/+21
Calling ethtool during reload can lead to call trace, because VSI isn't configured for some time, but netdev is alive. To fix it add rtnl lock for VSI deconfig and config. Set ::num_q_vectors to 0 after freeing and add a check for ::tx/rx_rings in ring related ethtool ops. Add proper unroll of filters in ice_start_eth(). Reproduction: $watch -n 0.1 -d 'ethtool -g enp24s0f0np0' $devlink dev reload pci/0000:18:00.0 action driver_reinit Call trace before fix: [66303.926205] BUG: kernel NULL pointer dereference, address: 0000000000000000 [66303.926259] #PF: supervisor read access in kernel mode [66303.926286] #PF: error_code(0x0000) - not-present page [66303.926311] PGD 0 P4D 0 [66303.926332] Oops: 0000 [#1] PREEMPT SMP PTI [66303.926358] CPU: 4 PID: 933821 Comm: ethtool Kdump: loaded Tainted: G OE 6.4.0-rc5+ #1 [66303.926400] Hardware name: Intel Corporation S2600WFT/S2600WFT, BIOS SE5C620.86B.00.01.0014.070920180847 07/09/2018 [66303.926446] RIP: 0010:ice_get_ringparam+0x22/0x50 [ice] [66303.926649] Code: 90 90 90 90 90 90 90 90 f3 0f 1e fa 0f 1f 44 00 00 48 8b 87 c0 09 00 00 c7 46 04 e0 1f 00 00 c7 46 10 e0 1f 00 00 48 8b 50 20 <48> 8b 12 0f b7 52 3a 89 56 14 48 8b 40 28 48 8b 00 0f b7 40 58 48 [66303.926722] RSP: 0018:ffffad40472f39c8 EFLAGS: 00010246 [66303.926749] RAX: ffff98a8ada05828 RBX: ffff98a8c46dd060 RCX: ffffad40472f3b48 [66303.926781] RDX: 0000000000000000 RSI: ffff98a8c46dd068 RDI: ffff98a8b23c4000 [66303.926811] RBP: ffffad40472f3b48 R08: 00000000000337b0 R09: 0000000000000000 [66303.926843] R10: 0000000000000001 R11: 0000000000000100 R12: ffff98a8b23c4000 [66303.926874] R13: ffff98a8c46dd060 R14: 000000000000000f R15: ffffad40472f3a50 [66303.926906] FS: 00007f6397966740(0000) GS:ffff98b390900000(0000) knlGS:0000000000000000 [66303.926941] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [66303.926967] CR2: 0000000000000000 CR3: 000000011ac20002 CR4: 00000000007706e0 [66303.926999] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [66303.927029] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [66303.927060] PKRU: 55555554 [66303.927075] Call Trace: [66303.927094] <TASK> [66303.927111] ? __die+0x23/0x70 [66303.927140] ? page_fault_oops+0x171/0x4e0 [66303.927176] ? exc_page_fault+0x7f/0x180 [66303.927209] ? asm_exc_page_fault+0x26/0x30 [66303.927244] ? ice_get_ringparam+0x22/0x50 [ice] [66303.927433] rings_prepare_data+0x62/0x80 [66303.927469] ethnl_default_doit+0xe2/0x350 [66303.927501] genl_family_rcv_msg_doit.isra.0+0xe3/0x140 [66303.927538] genl_rcv_msg+0x1b1/0x2c0 [66303.927561] ? __pfx_ethnl_default_doit+0x10/0x10 [66303.927590] ? __pfx_genl_rcv_msg+0x10/0x10 [66303.927615] netlink_rcv_skb+0x58/0x110 [66303.927644] genl_rcv+0x28/0x40 [66303.927665] netlink_unicast+0x19e/0x290 [66303.927691] netlink_sendmsg+0x254/0x4d0 [66303.927717] sock_sendmsg+0x93/0xa0 [66303.927743] __sys_sendto+0x126/0x170 [66303.927780] __x64_sys_sendto+0x24/0x30 [66303.928593] do_syscall_64+0x5d/0x90 [66303.929370] ? __count_memcg_events+0x60/0xa0 [66303.930146] ? count_memcg_events.constprop.0+0x1a/0x30 [66303.930920] ? handle_mm_fault+0x9e/0x350 [66303.931688] ? do_user_addr_fault+0x258/0x740 [66303.932452] ? exc_page_fault+0x7f/0x180 [66303.933193] entry_SYSCALL_64_after_hwframe+0x72/0xdc Fixes: 5b246e533d01 ("ice: split probe into smaller functions") Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com> Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com> Reviewed-by: Simon Horman <simon.horman@corigine.com> Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2023-07-14ice: Unregister netdev and devlink_port only oncePetr Oros1-27/+0
Since commit 6624e780a577fc ("ice: split ice_vsi_setup into smaller functions") ice_vsi_release does things twice. There is unregister netdev which is unregistered in ice_deinit_eth also. It also unregisters the devlink_port twice which is also unregistered in ice_deinit_eth(). This double deregistration is hidden because devl_port_unregister ignores the return value of xa_erase. [ 68.642167] Call Trace: [ 68.650385] ice_devlink_destroy_pf_port+0xe/0x20 [ice] [ 68.655656] ice_vsi_release+0x445/0x690 [ice] [ 68.660147] ice_deinit+0x99/0x280 [ice] [ 68.664117] ice_remove+0x1b6/0x5c0 [ice] [ 171.103841] Call Trace: [ 171.109607] ice_devlink_destroy_pf_port+0xf/0x20 [ice] [ 171.114841] ice_remove+0x158/0x270 [ice] [ 171.118854] pci_device_remove+0x3b/0xc0 [ 171.122779] device_release_driver_internal+0xc7/0x170 [ 171.127912] driver_detach+0x54/0x8c [ 171.131491] bus_remove_driver+0x77/0xd1 [ 171.135406] pci_unregister_driver+0x2d/0xb0 [ 171.139670] ice_module_exit+0xc/0x55f [ice] Fixes: 6624e780a577 ("ice: split ice_vsi_setup into smaller functions") Signed-off-by: Petr Oros <poros@redhat.com> Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com> Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2023-07-14gso: fix dodgy bit handling for GSO_UDP_L4Yan Zhai2-7/+12
Commit 1fd54773c267 ("udp: allow header check for dodgy GSO_UDP_L4 packets.") checks DODGY bit for UDP, but for packets that can be fed directly to the device after gso_segs reset, it actually falls through to fragmentation: https://lore.kernel.org/all/CAJPywTKDdjtwkLVUW6LRA2FU912qcDmQOQGt2WaDo28KzYDg+A@mail.gmail.com/ This change restores the expected behavior of GSO_UDP_L4 packets. Fixes: 1fd54773c267 ("udp: allow header check for dodgy GSO_UDP_L4 packets.") Suggested-by: Willem de Bruijn <willemdebruijn.kernel@gmail.com> Signed-off-by: Yan Zhai <yan@cloudflare.com> Reviewed-by: Willem de Bruijn <willemb@google.com> Acked-by: Jason Wang <jasowang@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2023-07-14net: ethernet: Remove repeating expressionWang Ming1-1/+0
Identify issues that arise by using the tests/doublebitand.cocci semantic patch. Need to remove duplicate expression in if statement. Signed-off-by: Wang Ming <machel@vivo.com> Reviewed-by: Jiawen Wu <jiawenwu@trustnetic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2023-07-14bna: Remove error checking for debugfs_create_dir()Wang Ming1-5/+0
It is expected that most callers should _ignore_ the errors return by debugfs_create_dir() in bnad_debugfs_init(). Signed-off-by: Wang Ming <machel@vivo.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2023-07-14net: ethernet: mtk_eth_soc: handle probe deferralDaniel Golle1-18/+11
Move the call to of_get_ethdev_address to mtk_add_mac which is part of the probe function and can hence itself return -EPROBE_DEFER should of_get_ethdev_address return -EPROBE_DEFER. This allows us to entirely get rid of the mtk_init function. The problem of of_get_ethdev_address returning -EPROBE_DEFER surfaced in situations in which the NVMEM provider holding the MAC address has not yet be loaded at the time mtk_eth_soc is initially probed. In this case probing of mtk_eth_soc should be deferred instead of falling back to use a random MAC address, so once the NVMEM provider becomes available probing can be repeated. Fixes: 656e705243fd ("net-next: mediatek: add support for MT7623 ethernet") Signed-off-by: Daniel Golle <daniel@makrotopia.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2023-07-14bridge: Add extack warning when enabling STP in netns.Kuniyuki Iwashima1-0/+3
When we create an L2 loop on a bridge in netns, we will see packets storm even if STP is enabled. # unshare -n # ip link add br0 type bridge # ip link add veth0 type veth peer name veth1 # ip link set veth0 master br0 up # ip link set veth1 master br0 up # ip link set br0 type bridge stp_state 1 # ip link set br0 up # sleep 30 # ip -s link show br0 2: br0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP mode DEFAULT group default qlen 1000 link/ether b6:61:98:1c:1c:b5 brd ff:ff:ff:ff:ff:ff RX: bytes packets errors dropped missed mcast 956553768 12861249 0 0 0 12861249 <-. Keep TX: bytes packets errors dropped carrier collsns | increasing 1027834 11951 0 0 0 0 <-' rapidly This is because llc_rcv() drops all packets in non-root netns and BPDU is dropped. Let's add extack warning when enabling STP in netns. # unshare -n # ip link add br0 type bridge # ip link set br0 type bridge stp_state 1 Warning: bridge: STP does not work in non-root netns. Note this commit will be reverted later when we namespacify the whole LLC infra. Fixes: e730c15519d0 ("[NET]: Make packet reception network namespace safe") Suggested-by: Harry Coin <hcoin@quietfountain.com> Link: https://lore.kernel.org/netdev/0f531295-e289-022d-5add-5ceffa0df9bc@quietfountain.com/ Suggested-by: Ido Schimmel <idosch@idosch.org> Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com> Acked-by: Nikolay Aleksandrov <razor@blackwall.org> Reviewed-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2023-07-14net: ethernet: ti: cpsw_ale: Fix cpsw_ale_get_field()/cpsw_ale_set_field()Tanmay Patil1-5/+19
CPSW ALE has 75 bit ALE entries which are stored within three 32 bit words. The cpsw_ale_get_field() and cpsw_ale_set_field() functions assume that the field will be strictly contained within one word. However, this is not guaranteed to be the case and it is possible for ALE field entries to span across up to two words at the most. Fix the methods to handle getting/setting fields spanning up to two words. Fixes: db82173f23c5 ("netdev: driver: ethernet: add cpsw address lookup engine support") Signed-off-by: Tanmay Patil <t-patil@ti.com> [s-vadapalli@ti.com: rephrased commit message and added Fixes tag] Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2023-07-14net: dsa: ar9331: Use explict flags for regmap single read/writeMark Brown1-2/+2
The at9331 is only able to read or write a single register at once. The driver has a custom regmap bus and chooses to tell the regmap core about this by reporting the maximum transfer sizes rather than the explicit flags that exist at the regmap level. Since there are a number of problems with the raw transfer limits and the regmap level flags are better integrated anyway convert the driver to use the flags. No functional change. Signed-off-by: Mark Brown <broonie@kernel.org> Reviewed-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2023-07-14net: usbnet: Fix WARNING in usbnet_start_xmit/usb_submit_urbAlan Stern1-0/+6
The syzbot fuzzer identified a problem in the usbnet driver: usb 1-1: BOGUS urb xfer, pipe 3 != type 1 WARNING: CPU: 0 PID: 754 at drivers/usb/core/urb.c:504 usb_submit_urb+0xed6/0x1880 drivers/usb/core/urb.c:504 Modules linked in: CPU: 0 PID: 754 Comm: kworker/0:2 Not tainted 6.4.0-rc7-syzkaller-00014-g692b7dc87ca6 #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 05/27/2023 Workqueue: mld mld_ifc_work RIP: 0010:usb_submit_urb+0xed6/0x1880 drivers/usb/core/urb.c:504 Code: 7c 24 18 e8 2c b4 5b fb 48 8b 7c 24 18 e8 42 07 f0 fe 41 89 d8 44 89 e1 4c 89 ea 48 89 c6 48 c7 c7 a0 c9 fc 8a e8 5a 6f 23 fb <0f> 0b e9 58 f8 ff ff e8 fe b3 5b fb 48 81 c5 c0 05 00 00 e9 84 f7 RSP: 0018:ffffc9000463f568 EFLAGS: 00010086 RAX: 0000000000000000 RBX: 0000000000000001 RCX: 0000000000000000 RDX: ffff88801eb28000 RSI: ffffffff814c03b7 RDI: 0000000000000001 RBP: ffff8881443b7190 R08: 0000000000000001 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000001 R12: 0000000000000003 R13: ffff88802a77cb18 R14: 0000000000000003 R15: ffff888018262500 FS: 0000000000000000(0000) GS:ffff8880b9800000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000556a99c15a18 CR3: 0000000028c71000 CR4: 0000000000350ef0 Call Trace: <TASK> usbnet_start_xmit+0xfe5/0x2190 drivers/net/usb/usbnet.c:1453 __netdev_start_xmit include/linux/netdevice.h:4918 [inline] netdev_start_xmit include/linux/netdevice.h:4932 [inline] xmit_one net/core/dev.c:3578 [inline] dev_hard_start_xmit+0x187/0x700 net/core/dev.c:3594 ... This bug is caused by the fact that usbnet trusts the bulk endpoint addresses its probe routine receives in the driver_info structure, and it does not check to see that these endpoints actually exist and have the expected type and directions. The fix is simply to add such a check. Reported-and-tested-by: syzbot+63ee658b9a100ffadbe2@syzkaller.appspotmail.com Closes: https://lore.kernel.org/linux-usb/000000000000a56e9105d0cec021@google.com/ Signed-off-by: Alan Stern <stern@rowland.harvard.edu> CC: Oliver Neukum <oneukum@suse.com> Link: https://lore.kernel.org/r/ea152b6d-44df-4f8a-95c6-4db51143dcc1@rowland.harvard.edu Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2023-07-14dsa: mv88e6xxx: Do a final check before timing outLinus Walleij1-0/+7
I get sporadic timeouts from the driver when using the MV88E6352. Reading the status again after the loop fixes the problem: the operation is successful but goes undetected. Some added prints show things like this: [ 58.356209] mv88e6085 mdio_mux-0.1:00: Timeout while waiting for switch, addr 1b reg 0b, mask 8000, val 0000, data c000 [ 58.367487] mv88e6085 mdio_mux-0.1:00: Timeout waiting for ATU op 4000, fid 0001 (...) [ 61.826293] mv88e6085 mdio_mux-0.1:00: Timeout while waiting for switch, addr 1c reg 18, mask 8000, val 0000, data 9860 [ 61.837560] mv88e6085 mdio_mux-0.1:00: Timeout waiting for PHY command 1860 to complete The reason is probably not the commands: I think those are mostly fine with the 50+50ms timeout, but the problem appears when OpenWrt brings up several interfaces in parallel on a system with 7 populated ports: if one of them take more than 50 ms and waits one or more of the others can get stuck on the mutex for the switch and then this can easily multiply. As we sleep and wait, the function loop needs a final check after exiting the loop if we were successful. Suggested-by: Andrew Lunn <andrew@lunn.ch> Cc: Tobias Waldekranz <tobias@waldekranz.com> Fixes: 35da1dfd9484 ("net: dsa: mv88e6xxx: Improve performance of busy bit polling") Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/20230712223405.861899-1-linus.walleij@linaro.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2023-07-14Merge tag 'net-6.5-rc2' of ↵Linus Torvalds91-521/+1011
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net Pull networking fixes from Paolo Abeni: "Including fixes from netfilter, wireless and ebpf. Current release - regressions: - netfilter: conntrack: gre: don't set assured flag for clash entries - wifi: iwlwifi: remove 'use_tfh' config to fix crash Previous releases - regressions: - ipv6: fix a potential refcount underflow for idev - icmp6: ifix null-ptr-deref of ip6_null_entry->rt6i_idev in icmp6_dev() - bpf: fix max stack depth check for async callbacks - eth: mlx5e: - check for NOT_READY flag state after locking - fix page_pool page fragment tracking for XDP - eth: igc: - fix tx hang issue when QBV gate is closed - fix corner cases for TSN offload - eth: octeontx2-af: Move validation of ptp pointer before its usage - eth: ena: fix shift-out-of-bounds in exponential backoff Previous releases - always broken: - core: prevent skb corruption on frag list segmentation - sched: - cls_fw: fix improper refcount update leads to use-after-free - sch_qfq: account for stab overhead in qfq_enqueue - netfilter: - report use refcount overflow - prevent OOB access in nft_byteorder_eval - wifi: mt7921e: fix init command fail with enabled device - eth: ocelot: fix oversize frame dropping for preemptible TCs - eth: fec: recycle pages for transmitted XDP frames" * tag 'net-6.5-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (79 commits) selftests: tc-testing: add test for qfq with stab overhead net/sched: sch_qfq: account for stab overhead in qfq_enqueue selftests: tc-testing: add tests for qfq mtu sanity check net/sched: sch_qfq: reintroduce lmax bound check for MTU wifi: cfg80211: fix receiving mesh packets without RFC1042 header wifi: rtw89: debug: fix error code in rtw89_debug_priv_send_h2c_set() net: txgbe: fix eeprom calculation error net/sched: make psched_mtu() RTNL-less safe net: ena: fix shift-out-of-bounds in exponential backoff netdevsim: fix uninitialized data in nsim_dev_trap_fa_cookie_write() net/sched: flower: Ensure both minimum and maximum ports are specified MAINTAINERS: Add another mailing list for QUALCOMM ETHQOS ETHERNET DRIVER docs: netdev: update the URL of the status page wifi: iwlwifi: remove 'use_tfh' config to fix crash xdp: use trusted arguments in XDP hints kfuncs bpf: cpumap: Fix memory leak in cpu_map_update_elem wifi: airo: avoid uninitialized warning in airo_get_rate() octeontx2-pf: Add additional check for MCAM rules net: dsa: Removed unneeded of_node_put in felix_parse_ports_node net: fec: use netdev_err_once() instead of netdev_err() ...
2023-07-13Merge tag 'trace-v6.5-rc1-3' of ↵Linus Torvalds20-40/+268
git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace Pull tracing fixes from Steven Rostedt: - Fix some missing-prototype warnings - Fix user events struct args (did not include size of struct) When creating a user event, the "struct" keyword is to denote that the size of the field will be passed in. But the parsing failed to handle this case. - Add selftest to struct sizes for user events - Fix sample code for direct trampolines. The sample code for direct trampolines attached to handle_mm_fault(). But the prototype changed and the direct trampoline sample code was not updated. Direct trampolines needs to have the arguments correct otherwise it can fail or crash the system. - Remove unused ftrace_regs_caller_ret() prototype. - Quiet false positive of FORTIFY_SOURCE Due to backward compatibility, the structure used to save stack traces in the kernel had a fixed size of 8. This structure is exported to user space via the tracing format file. A change was made to allow more than 8 functions to be recorded, and user space now uses the size field to know how many functions are actually in the stack. But the structure still has size of 8 (even though it points into the ring buffer that has the required amount allocated to hold a full stack. This was fine until the fortifier noticed that the memcpy(&entry->caller, stack, size) was greater than the 8 functions and would complain at runtime about it. Hide this by using a pointer to the stack location on the ring buffer instead of using the address of the entry structure caller field. - Fix a deadloop in reading trace_pipe that was caused by a mismatch between ring_buffer_empty() returning false which then asked to read the data, but the read code uses rb_num_of_entries() that returned zero, and causing a infinite "retry". - Fix a warning caused by not using all pages allocated to store ftrace functions, where this can happen if the linker inserts a bunch of "NULL" entries, causing the accounting of how many pages needed to be off. - Fix histogram synthetic event crashing when the start event is removed and the end event is still using a variable from it - Fix memory leak in freeing iter->temp in tracing_release_pipe() * tag 'trace-v6.5-rc1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace: tracing: Fix memory leak of iter->temp when reading trace_pipe tracing/histograms: Add histograms to hist_vars if they have referenced variables tracing: Stop FORTIFY_SOURCE complaining about stack trace caller ftrace: Fix possible warning on checking all pages used in ftrace_process_locs() ring-buffer: Fix deadloop issue on reading trace_pipe tracing: arm64: Avoid missing-prototype warnings selftests/user_events: Test struct size match cases tracing/user_events: Fix struct arg size match check x86/ftrace: Remove unsued extern declaration ftrace_regs_caller_ret() arm64: ftrace: Add direct call trampoline samples support samples: ftrace: Save required argument registers in sample trampolines
2023-07-13Merge tag 'for-linus-6.5-rc2-tag' of ↵Linus Torvalds2-16/+23
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip Pull xen fixes from Juergen Gross: - a cleanup of the Xen related ELF-notes - a fix for virtio handling in Xen dom0 when running Xen in a VM * tag 'for-linus-6.5-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip: xen/virtio: Fix NULL deref when a bridge of PCI root bus has no parent x86/Xen: tidy xen-head.S
2023-07-13Merge tag 'sh-for-v6.5-tag2' of ↵Linus Torvalds5-10/+10
git://git.kernel.org/pub/scm/linux/kernel/git/glaubitz/sh-linux Pull sh fixes from John Paul Adrian Glaubitz: "The sh updates introduced multiple regressions. In particular, the change a8ac2961148e ("sh: Avoid using IRQ0 on SH3 and SH4") causes several boards to hang during boot due to incorrect IRQ numbers. Geert Uytterhoeven has contributed patches that handle the virq offset in the IRQ code for the dreamcast, highlander and r2d boards while Artur Rojek has contributed a patch which handles the virq offset for the hd64461 companion chip" * tag 'sh-for-v6.5-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/glaubitz/sh-linux: sh: hd64461: Handle virq offset for offchip IRQ base and HD64461 IRQ sh: mach-dreamcast: Handle virq offset in cascaded IRQ demux sh: mach-highlander: Handle virq offset in cascaded IRL demux sh: mach-r2d: Handle virq offset in cascaded IRL demux
2023-07-13tracing: Fix memory leak of iter->temp when reading trace_pipeZheng Yejian1-0/+1
kmemleak reports: unreferenced object 0xffff88814d14e200 (size 256): comm "cat", pid 336, jiffies 4294871818 (age 779.490s) hex dump (first 32 bytes): 04 00 01 03 00 00 00 00 08 00 00 00 00 00 00 00 ................ 0c d8 c8 9b ff ff ff ff 04 5a ca 9b ff ff ff ff .........Z...... backtrace: [<ffffffff9bdff18f>] __kmalloc+0x4f/0x140 [<ffffffff9bc9238b>] trace_find_next_entry+0xbb/0x1d0 [<ffffffff9bc9caef>] trace_print_lat_context+0xaf/0x4e0 [<ffffffff9bc94490>] print_trace_line+0x3e0/0x950 [<ffffffff9bc95499>] tracing_read_pipe+0x2d9/0x5a0 [<ffffffff9bf03a43>] vfs_read+0x143/0x520 [<ffffffff9bf04c2d>] ksys_read+0xbd/0x160 [<ffffffff9d0f0edf>] do_syscall_64+0x3f/0x90 [<ffffffff9d2000aa>] entry_SYSCALL_64_after_hwframe+0x6e/0xd8 when reading file 'trace_pipe', 'iter->temp' is allocated or relocated in trace_find_next_entry() but not freed before 'trace_pipe' is closed. To fix it, free 'iter->temp' in tracing_release_pipe(). Link: https://lore.kernel.org/linux-trace-kernel/20230713141435.1133021-1-zhengyejian1@huawei.com Cc: stable@vger.kernel.org Fixes: ff895103a84ab ("tracing: Save off entry when peeking at next entry") Signed-off-by: Zheng Yejian <zhengyejian1@huawei.com> Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
2023-07-13Merge branch 'net-sched-fixes-for-sch_qfq'Paolo Abeni2-3/+101
Pedro Tammela says: ==================== net/sched: fixes for sch_qfq Patch 1 fixes a regression introduced in 6.4 where the MTU size could be bigger than 'lmax'. Patch 3 fixes an issue where the code doesn't account for qdisc_pkt_len() returning a size bigger then 'lmax'. Patches 2 and 4 are selftests for the issues above. ==================== Link: https://lore.kernel.org/r/20230711210103.597831-1-pctammela@mojatatu.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2023-07-13selftests: tc-testing: add test for qfq with stab overheadPedro Tammela1-0/+38
A packet with stab overhead greater than QFQ_MAX_LMAX should be dropped by the QFQ qdisc as it can't handle such lengths. Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: Pedro Tammela <pctammela@mojatatu.com> Reviewed-by: Simon Horman <simon.horman@corigine.com> Tested-by: Zhengchao Shao <shaozhengchao@huawei.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
generated by cgit v1.2.3 (git 2.39.0) at 2025-09-29 10:27:14 +0300