| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Add cold boot calibration support on WCN6750. Unlike other
chipsets where firmware(FW) is restarted after cold boot
calibration is completed, it is recommended not to restart
the firmware for WCN6750.
For WCN6750, FW sends both CAL_DONE & FW_READY QMI indication
to the driver after cold boot calibration is completed.
QMI message flow for WCN6750 with cold boot support:
FW_INIT_DONE to HOST -> CALIBRATION Mode to FW -> CAL_DONE to Host ->
FW_READY to Host -> MODE_ON to FW
QMI message flow for other chipsets with cold boot support:
FW_INIT_DONE to Host -> CALIBRATION Mode to FW -> FW_READY to Host ->
Trigger FW restart -> FW_INIT_DONE to HOST -> MODE_ON to FW
QMI message flow for chipsets without cold boot support:
FW_INIT_DONE to Host -> MODE_ON to FW
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220720134909.15626-3-quic_mpubbise@quicinc.com
|
|
QMI message IDs for some of the QMI messages were incorrectly
defined in the original implementation. These have to be corrected
to enable cold boot support on WCN6750. These corrections are
applicable for all chipsets and will not impact them. Refactor the
code accordingly.
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1
Fixes: d5c65159f289 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220720134909.15626-2-quic_mpubbise@quicinc.com
|
|
When the system shuts down, SMMU driver will be stopped and
will not assist in IOVA translations. SMMU driver expects all
of its consumers to shutdown before shutting down itself.
WCN6750 being one of the consumer device should not perform any
DMA operations after the SMMU has shutdown which will otherwise
result in SMMU faults.
SMMU driver will call the shutdown() callback of all its
consumer devices and the consumers shall stop further DMA
activity after the invocation of their respective shutdown()
callbacks.
Register the shutdown() callback to the platform core for WCN6750.
Change will not impact other AHB ath11k devices.
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220720134710.15523-1-quic_mpubbise@quicinc.com
|
|
ath.git patches for v6.1. Only fixes this time.
|
|
syzbot is reporting uninit value at ath9k_htc_rx_msg() [1], for
ioctl(USB_RAW_IOCTL_EP_WRITE) can call ath9k_hif_usb_rx_stream() with
pkt_len = 0 but ath9k_hif_usb_rx_stream() uses
__dev_alloc_skb(pkt_len + 32, GFP_ATOMIC) based on an assumption that
pkt_len is valid. As a result, ath9k_hif_usb_rx_stream() allocates skb
with uninitialized memory and ath9k_htc_rx_msg() is reading from
uninitialized memory.
Since bytes accessed by ath9k_htc_rx_msg() is not known until
ath9k_htc_rx_msg() is called, it would be difficult to check minimal valid
pkt_len at "if (pkt_len > 2 * MAX_RX_BUF_SIZE) {" line in
ath9k_hif_usb_rx_stream().
We have two choices. One is to workaround by adding __GFP_ZERO so that
ath9k_htc_rx_msg() sees 0 if pkt_len is invalid. The other is to let
ath9k_htc_rx_msg() validate pkt_len before accessing. This patch chose
the latter.
Note that I'm not sure threshold condition is correct, for I can't find
details on possible packet length used by this protocol.
Link: https://syzkaller.appspot.com/bug?extid=2ca247c2d60c7023de7f [1]
Reported-by: syzbot <syzbot+2ca247c2d60c7023de7f@syzkaller.appspotmail.com>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/7acfa1be-4b5c-b2ce-de43-95b0593fb3e5@I-love.SAKURA.ne.jp
|
|
Add the missing unlock before return in the error handling case.
Fixes: ccdde7c74ffd ("wifi: mac80211: properly implement MLO key handling")
Signed-off-by: Sun Ke <sunke32@huawei.com>
Link: https://lore.kernel.org/r/20220827022452.823381-1-sunke32@huawei.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Johannes berg says:
====================
Various updates:
* rtw88: operation, locking, warning, and code style fixes
* rtw89: small updates
* cfg80211/mac80211: more EHT/MLO (802.11be, WiFi 7) work
* brcmfmac: a couple of fixes
* misc cleanups etc.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Lenovo OneLink+ Dock contains an RTL8153 controller that behaves as
a broken CDC device by default. Add the custom Lenovo PID to the r8152
driver to support it properly.
Also, systems compatible with this dock provide a BIOS option to enable
MAC address passthrough (as per Lenovo document "ThinkPad Docking
Solutions 2017"). Add the custom PID to the MAC passthrough list too.
Tested on a ThinkPad 13 1st gen with the expected results:
passthrough disabled: Invalid header when reading pass-thru MAC addr
passthrough enabled: Using pass-thru MAC addr XX:XX:XX:XX:XX:XX
Signed-off-by: Jean-Francois Le Fillatre <jflf_kernel@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2022-08-24 (ice)
This series contains updates to ice driver only.
Marcin adds support for TC parsing on TTL and ToS fields.
Anatolli adds support for devlink port split command to allow
configuration of various port configurations.
Jake allows for passing and writing an additional NVM write activate
field by expanding current cmd_flag.
Ani makes PHY debug output more readable.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
clang reports uninitialized use:
>> drivers/net/wireless/realtek/rtw88/main.c:731:2: warning: variable
'primary_channel_idx' is used uninitialized whenever switch default is
taken [-Wsometimes-uninitialized]
default:
^~~~~~~
drivers/net/wireless/realtek/rtw88/main.c:754:39: note: uninitialized
use occurs here
hal->current_primary_channel_index = primary_channel_idx;
^~~~~~~~~~~~~~~~~~~
drivers/net/wireless/realtek/rtw88/main.c:687:24: note: initialize the
variable 'primary_channel_idx' to silence this warning
u8 primary_channel_idx;
^
= '\0'
This situation could not happen, because possible channel bandwidth
20/40/80MHz are enumerated.
Fixes: 341dd1f7de4c ("wifi: rtw88: add the update channel flow to support setting by parameters")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/r/20220815062004.22920-1-pkshih@realtek.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
As per RGMII specification v2.0, section 3.4.1, RGMII/RTBI has an
optional in-band status feature where the PHY's link status, speed and
duplex mode can be passed to the MAC.
Allow RGMII/RTBI to use in-band status.
Signed-off-by: Qingfang DENG <dqfext@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Maksym Glubokiy says:
====================
net: prestera: matchall features
This patch series extracts matchall rules management out of SPAN API
implementation and adds 2 features on top of that:
- support for egress traffic (mirred egress action)
- proper rule priorities management between matchall and flower
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
matchall rules can be added only to chain 0 and their priorities have
limitations:
- new matchall ingress rule's priority must be higher (lower value)
than any existing flower rule;
- new matchall egress rule's priority must be lower (higher value)
than any existing flower rule.
The opposite works for flower rule adding:
- new flower ingress rule's priority must be lower (higher value)
than any existing matchall rule;
- new flower egress rule's priority must be higher (lower value)
than any existing matchall rule.
This is a hardware limitation and thus must be properly handled in
driver by reporting errors to the user when newly added rule has such a
priority that cannot be installed into the hardware.
To achieve this, the driver must maintain both min/max matchall
priorities for every flower block when user adds/deletes a matchall
rule, as well as both min/max flower priorities for chain 0 for every
adding/deletion of flower rules for chain 0.
Cc: Serhiy Boiko <serhiy.boiko@plvision.eu>
Signed-off-by: Maksym Glubokiy <maksym.glubokiy@plvision.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This enables adding matchall rules for egress:
tc filter add .. egress .. matchall skip_sw \
action mirred egress mirror dev ..
Signed-off-by: Serhiy Boiko <serhiy.boiko@plvision.eu>
Signed-off-by: Maksym Glubokiy <maksym.glubokiy@plvision.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This commit adds more clarity to handling of TC_CLSMATCHALL_REPLACE and
TC_CLSMATCHALL_DESTROY events by calling newly added *_mall_*() handlers
instead of directly calling SPAN API.
This also extracts matchall rules management out of SPAN API since SPAN
is a hardware module which is used to implement 'matchall egress mirred'
action only.
Signed-off-by: Taras Chornyi <tchornyi@marvell.com>
Signed-off-by: Serhiy Boiko <serhiy.boiko@plvision.eu>
Signed-off-by: Maksym Glubokiy <maksym.glubokiy@plvision.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add phylink based ethtool pause configuration
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are some exotic ax88772 based devices which may require
functionality provide by the phylink framework. For example:
- US100A20SFP, USB 2.0 auf LWL Converter with SFP Cage
- AX88772B USB to 100Base-TX Ethernet (with RMII) demo board, where it
is possible to switch between internal PHY and external RMII based
connection.
So, convert this driver to phylink as soon as possible.
Tested with:
- AX88772A + internal PHY
- AX88772B + external DP83TD510E T1L PHY
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The full 'unsigned int' is better than 'unsigned'.
Signed-off-by: Xin Gao <gaoxin@cdjrlc.com>
Link: https://lore.kernel.org/r/20220816181040.9044-1-gaoxin@cdjrlc.com
[fix indentation]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Follow the advice of the below link and prefer 'strscpy' in this
subsystem. Conversion is 1:1 because the return value is not used.
Generated by a coccinelle script.
Link: https://lore.kernel.org/r/CAHk-=wgfRnXz0W3D37d01q3JFkr_i_uTL=V6A6G1oUZcprmknw@mail.gmail.com/
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Driver may update sinfo directly through .sta_statistics, so this
patch makes sure that ethool gets the correct statistics.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Link: https://lore.kernel.org/r/f9edff14dd7f5205acf1c21bae8e9d8f9802dd88.1661466499.git.ryder.lee@mediatek.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
If we add 6 GHz capability in MLO, we cannot use the SMPS
mode from the deflink. Pass it separately instead since on
a second link we don't even have a link data struct yet.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
In order to ensure only documented properties are present, node schemas
must have unevaluatedProperties or additionalProperties set to false
(typically). Add missing properties/$refs as exposed by this addition.
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20220825192609.1538463-1-robh@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
drivers/net/ethernet/mellanox/mlx5/core/en_fs.c
21234e3a84c7 ("net/mlx5e: Fix use after free in mlx5e_fs_init()")
c7eafc5ed068 ("net/mlx5e: Convert ethtool_steering member of flow_steering struct to pointer")
https://lore.kernel.org/all/20220825104410.67d4709c@canb.auug.org.au/
https://lore.kernel.org/all/20220823055533.334471-1-saeed@kernel.org/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Use try_cmpxchg instead of cmpxchg (*ptr, old, new) == old in
napi_if_scheduled_mark_missed. x86 CMPXCHG instruction returns
success in ZF flag, so this change saves a compare after cmpxchg
(and related move instruction in front of cmpxchg).
Also, try_cmpxchg implicitly assigns old *ptr value to "old" when cmpxchg
fails, enabling further code simplifications.
Cc: Eric Dumazet <edumazet@google.com>
Cc: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Uros Bizjak <ubizjak@gmail.com>
Link: https://lore.kernel.org/r/20220822143243.2798-1-ubizjak@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from ipsec and netfilter (with one broken Fixes tag).
Current release - new code bugs:
- dsa: don't dereference NULL extack in dsa_slave_changeupper()
- dpaa: fix <1G ethernet on LS1046ARDB
- neigh: don't call kfree_skb() under spin_lock_irqsave()
Previous releases - regressions:
- r8152: fix the RX FIFO settings when suspending
- dsa: microchip: keep compatibility with device tree blobs with no
phy-mode
- Revert "net: macsec: update SCI upon MAC address change."
- Revert "xfrm: update SA curlft.use_time", comply with RFC 2367
Previous releases - always broken:
- netfilter: conntrack: work around exceeded TCP receive window
- ipsec: fix a null pointer dereference of dst->dev on a metadata dst
in xfrm_lookup_with_ifid
- moxa: get rid of asymmetry in DMA mapping/unmapping
- dsa: microchip: make learning configurable and keep it off while
standalone
- ice: xsk: prohibit usage of non-balanced queue id
- rxrpc: fix locking in rxrpc's sendmsg
Misc:
- another chunk of sysctl data race silencing"
* tag 'net-6.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (87 commits)
net: lantiq_xrx200: restore buffer if memory allocation failed
net: lantiq_xrx200: fix lock under memory pressure
net: lantiq_xrx200: confirm skb is allocated before using
net: stmmac: work around sporadic tx issue on link-up
ionic: VF initial random MAC address if no assigned mac
ionic: fix up issues with handling EAGAIN on FW cmds
ionic: clear broken state on generation change
rxrpc: Fix locking in rxrpc's sendmsg
net: ethernet: mtk_eth_soc: fix hw hash reporting for MTK_NETSYS_V2
MAINTAINERS: rectify file entry in BONDING DRIVER
i40e: Fix incorrect address type for IPv6 flow rules
ixgbe: stop resetting SYSTIME in ixgbe_ptp_start_cyclecounter
net: Fix a data-race around sysctl_somaxconn.
net: Fix a data-race around netdev_unregister_timeout_secs.
net: Fix a data-race around gro_normal_batch.
net: Fix data-races around sysctl_devconf_inherit_init_net.
net: Fix data-races around sysctl_fb_tunnels_only_for_init_net.
net: Fix a data-race around netdev_budget_usecs.
net: Fix data-races around sysctl_max_skb_frags.
net: Fix a data-race around netdev_budget.
...
|
|
Petr Machata says:
====================
mlxsw: Remove some unused code
This patchset removes code that is not used anymore after the following two
commits removed all users:
- commit b0d80c013b04 ("mlxsw: Remove Mellanox SwitchX-2 ASIC support")
- commit 9b43fbb8ce24 ("mlxsw: Remove Mellanox SwitchIB ASIC support")
====================
Link: https://lore.kernel.org/r/cover.1661350629.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Function mlxsw_core_port_type_get() is no longer used. So remove it.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
port_type_set devlink op is no longer used by any mlxsw driver,
so remove it.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
There are some IB leftovers that are no longer used in the code.
So remove them.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Jiri Pirko says:
====================
net: devlink: sync flash and dev info commands
Purpose of this patchset is to introduce consistency between two devlink
commands:
devlink dev info
Shows versions of running default flash target and components.
devlink dev flash
Flashes default flash target or component name (if specified
on cmdline).
Currently it is up to the driver what versions to expose and what flash
update component names to accept. This is inconsistent. Thankfully, only
netdevsim currently using components so it is still time
to sanitize this.
This patchset makes sure, that devlink.c calls into driver for
component flash update only in case the driver exposes the same version
name.
Example:
$ devlink dev info
netdevsim/netdevsim10:
driver netdevsim
versions:
running:
fw.mgmt 10.20.30
stored:
fw.mgmt 10.20.30
$ devlink dev flash netdevsim/netdevsim10 file somefile.bin
[fw.mgmt] Preparing to flash
[fw.mgmt] Flashing 100%
[fw.mgmt] Flash select
[fw.mgmt] Flashing done
$ devlink dev flash netdevsim/netdevsim10 file somefile.bin component fw.mgmt
[fw.mgmt] Preparing to flash
[fw.mgmt] Flashing 100%
[fw.mgmt] Flash select
[fw.mgmt] Flashing done
$ devlink dev flash netdevsim/netdevsim10 file somefile.bin component dummy
Error: selected component is not supported by this device.
====================
Link: https://lore.kernel.org/r/20220824122011.1204330-1-jiri@resnulli.us
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Limit the acceptance of component name passed to cmd_flash_update() to
match one of the versions returned by info_get(), marked by version type.
This makes things clearer and enforces 1:1 mapping between exposed
version and accepted flash component.
Check VERSION_TYPE_COMPONENT version type during cmd_flash_update()
execution by calling info_get() with different "req" context.
That causes info_get() to lookup the component name instead of
filling-up the netlink message.
Remove "UPDATE_COMPONENT" flag which becomes used.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fix the only component user which is netdevsim. It uses component named
"fw.mgmt" in selftests. So add this version to info_get() output with
version type component.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Whenever the driver is called by his info_get() op, it may put multiple
version names and values to the netlink message. Extend by additional
helper devlink_info_version_running/stored_put_ext() that allows to
specify a version type that indicates when particular version name
represents a flash component.
This is going to be used in follow-up patch calling info_get() during
flash update command checking if version with this the version type
exists.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Assinging will drop all previous tests.
Fixes: b690842d12fd ("selftests/net: test l2 tunnel TOS/TTL inheriting")
Signed-off-by: Adel Abouchaev <adel.abushaev@gmail.com>
Reviewed-by: Shuah Khan <skhan@linuxfoundation.org>
Link: https://lore.kernel.org/r/20220824184351.3759862-1-adel.abushaev@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Aleksander Jan Bajkowski says:
====================
net: lantiq_xrx200: fix errors under memory pressure
This series fixes issues that can occur in the driver under memory pressure.
Situations when the system cannot allocate memory are rare, so the mentioned
bugs have been fixed recently. The patches have been tested on a BT Home
router with the Lantiq xRX200 chipset.
Changelog:
v3: - removed netdev_err() log from the first patch
v2:
- the second patch has been changed, so that under memory pressure situation
the driver will not receive packets indefinitely regardless of the NAPI budget,
- the third patch has been added.
====================
Link: https://lore.kernel.org/r/20220824215408.4695-1-olek2@wp.pl
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In a situation where memory allocation fails, an invalid buffer address
is stored. When this descriptor is used again, the system panics in the
build_skb() function when accessing memory.
Fixes: 7ea6cd16f159 ("lantiq: net: fix duplicated skb in rx descriptor ring")
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When the xrx200_hw_receive() function returns -ENOMEM, the NAPI poll
function immediately returns an error.
This is incorrect for two reasons:
* the function terminates without enabling interrupts or scheduling NAPI,
* the error code (-ENOMEM) is returned instead of the number of received
packets.
After the first memory allocation failure occurs, packet reception is
locked due to disabled interrupts from DMA..
Fixes: fe1a56420cf2 ("net: lantiq: Add Lantiq / Intel VRX200 Ethernet driver")
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
xrx200_hw_receive() assumes build_skb() always works and goes straight
to skb_reserve(). However, build_skb() can fail under memory pressure.
Add a check in case build_skb() failed to allocate and return NULL.
Fixes: e015593573b3 ("net: lantiq_xrx200: convert to build_skb")
Reported-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This is a follow-up to the discussion in [0]. It seems to me that
at least the IP version used on Amlogic SoC's sometimes has a problem
if register MAC_CTRL_REG is written whilst the chip is still processing
a previous write. But that's just a guess.
Adding a delay between two writes to this register helps, but we can
also simply omit the offending second write. This patch uses the second
approach and is based on a suggestion from Qi Duan.
Benefit of this approach is that we can save few register writes, also
on not affected chip versions.
[0] https://www.spinics.net/lists/netdev/msg831526.html
Fixes: bfab27a146ed ("stmmac: add the experimental PCI support")
Suggested-by: Qi Duan <qi.duan@amlogic.com>
Suggested-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/e99857ce-bd90-5093-ca8c-8cd480b5a0a2@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2022-08-24 (ixgbe, i40e)
This series contains updates to ixgbe and i40e drivers.
Jake stops incorrect resetting of SYSTIME registers when starting
cyclecounter for ixgbe.
Sylwester corrects a check on source IP address when validating destination
for i40e.
* '10GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
i40e: Fix incorrect address type for IPv6 flow rules
ixgbe: stop resetting SYSTIME in ixgbe_ptp_start_cyclecounter
====================
Link: https://lore.kernel.org/r/20220824193748.874343-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Shannon Nelson says:
====================
ionic: bug fixes
These are a couple of maintenance bug fixes for the Pensando ionic
networking driver.
Mohamed takes care of a "plays well with others" issue where the
VF spec is a bit vague on VF mac addresses, but certain customers
have come to expect behavior based on other vendor drivers.
Shannon addresses a couple of corner cases seen in internal
stress testing.
====================
Link: https://lore.kernel.org/r/20220824165051.6185-1-snelson@pensando.io
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Assign a random mac address to the VF interface station
address if it boots with a zero mac address in order to match
similar behavior seen in other VF drivers. Handle the errors
where the older firmware does not allow the VF to set its own
station address.
Newer firmware will allow the VF to set the station mac address
if it hasn't already been set administratively through the PF.
Setting it will also be allowed if the VF has trust.
Fixes: fbb39807e9ae ("ionic: support sr-iov operations")
Signed-off-by: R Mohamed Shah <mohamed@pensando.io>
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In looping on FW update tests we occasionally see the
FW_ACTIVATE_STATUS command fail while it is in its EAGAIN loop
waiting for the FW activate step to finsh inside the FW. The
firmware is complaining that the done bit is set when a new
dev_cmd is going to be processed.
Doing a clean on the cmd registers and doorbell before exiting
the wait-for-done and cleaning the done bit before the sleep
prevents this from occurring.
Fixes: fbfb8031533c ("ionic: Add hardware init and device commands")
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
There is a case found in heavy testing where a link flap happens just
before a firmware Recovery event and the driver gets stuck in the
BROKEN state. This comes from the driver getting interrupted by a FW
generation change when coming back up from the link flap, and the call
to ionic_start_queues() in ionic_link_status_check() fails. This can be
addressed by having the fw_up code clear the BROKEN bit if seen, rather
than waiting for a user to manually force the interface down and then
back up.
Fixes: 9e8eaf8427b6 ("ionic: stop watchdog when in broken state")
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fix three bugs in the rxrpc's sendmsg implementation:
(1) rxrpc_new_client_call() should release the socket lock when returning
an error from rxrpc_get_call_slot().
(2) rxrpc_wait_for_tx_window_intr() will return without the call mutex
held in the event that we're interrupted by a signal whilst waiting
for tx space on the socket or relocking the call mutex afterwards.
Fix this by: (a) moving the unlock/lock of the call mutex up to
rxrpc_send_data() such that the lock is not held around all of
rxrpc_wait_for_tx_window*() and (b) indicating to higher callers
whether we're return with the lock dropped. Note that this means
recvmsg() will not block on this call whilst we're waiting.
(3) After dropping and regaining the call mutex, rxrpc_send_data() needs
to go and recheck the state of the tx_pending buffer and the
tx_total_len check in case we raced with another sendmsg() on the same
call.
Thinking on this some more, it might make sense to have different locks for
sendmsg() and recvmsg(). There's probably no need to make recvmsg() wait
for sendmsg(). It does mean that recvmsg() can return MSG_EOR indicating
that a call is dead before a sendmsg() to that call returns - but that can
currently happen anyway.
Without fix (2), something like the following can be induced:
WARNING: bad unlock balance detected!
5.16.0-rc6-syzkaller #0 Not tainted
-------------------------------------
syz-executor011/3597 is trying to release lock (&call->user_mutex) at:
[<ffffffff885163a3>] rxrpc_do_sendmsg+0xc13/0x1350 net/rxrpc/sendmsg.c:748
but there are no more locks to release!
other info that might help us debug this:
no locks held by syz-executor011/3597.
...
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0xcd/0x134 lib/dump_stack.c:106
print_unlock_imbalance_bug include/trace/events/lock.h:58 [inline]
__lock_release kernel/locking/lockdep.c:5306 [inline]
lock_release.cold+0x49/0x4e kernel/locking/lockdep.c:5657
__mutex_unlock_slowpath+0x99/0x5e0 kernel/locking/mutex.c:900
rxrpc_do_sendmsg+0xc13/0x1350 net/rxrpc/sendmsg.c:748
rxrpc_sendmsg+0x420/0x630 net/rxrpc/af_rxrpc.c:561
sock_sendmsg_nosec net/socket.c:704 [inline]
sock_sendmsg+0xcf/0x120 net/socket.c:724
____sys_sendmsg+0x6e8/0x810 net/socket.c:2409
___sys_sendmsg+0xf3/0x170 net/socket.c:2463
__sys_sendmsg+0xe5/0x1b0 net/socket.c:2492
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x35/0xb0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae
[Thanks to Hawkins Jiawei and Khalid Masum for their attempts to fix this]
Fixes: bc5e3a546d55 ("rxrpc: Use MSG_WAITALL to tell sendmsg() to temporarily ignore signals")
Reported-by: syzbot+7f0483225d0c94cb3441@syzkaller.appspotmail.com
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Marc Dionne <marc.dionne@auristor.com>
Tested-by: syzbot+7f0483225d0c94cb3441@syzkaller.appspotmail.com
cc: Hawkins Jiawei <yin31149@gmail.com>
cc: Khalid Masum <khalid.masum.92@gmail.com>
cc: Dan Carpenter <dan.carpenter@oracle.com>
cc: linux-afs@lists.infradead.org
Link: https://lore.kernel.org/r/166135894583.600315.7170979436768124075.stgit@warthog.procyon.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup
Pull another cgroup fix from Tejun Heo:
"Commit 4f7e7236435c ("cgroup: Fix threadgroup_rwsem <->
cpus_read_lock() deadlock") required the cgroup
core to grab cpus_read_lock() before invoking ->attach().
Unfortunately, it missed adding cpus_read_lock() in
cgroup_attach_task_all(). Fix it"
* tag 'cgroup-for-6.0-rc2-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
cgroup: Add missing cpus_read_lock() to cgroup_attach_task_all()
|
|
syzbot is hitting percpu_rwsem_assert_held(&cpu_hotplug_lock) warning at
cpuset_attach() [1], for commit 4f7e7236435ca0ab ("cgroup: Fix
threadgroup_rwsem <-> cpus_read_lock() deadlock") missed that
cpuset_attach() is also called from cgroup_attach_task_all().
Add cpus_read_lock() like what cgroup_procs_write_start() does.
Link: https://syzkaller.appspot.com/bug?extid=29d3a3b4d86c8136ad9e [1]
Reported-by: syzbot <syzbot+29d3a3b4d86c8136ad9e@syzkaller.appspotmail.com>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Fixes: 4f7e7236435ca0ab ("cgroup: Fix threadgroup_rwsem <-> cpus_read_lock() deadlock")
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
qdisc_reset() is clearing qdisc->q.qlen and qdisc->qstats.backlog
_after_ calling qdisc->ops->reset. There is no need to clear them
again in the specific reset function.
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Link: https://lore.kernel.org/r/20220824005231.345727-1-shaozhengchao@huawei.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Properly report hw rx hash for mt7986 chipset accroding to the new dma
descriptor layout.
Fixes: 197c9e9b17b11 ("net: ethernet: mtk_eth_soc: introduce support for mt7986 chipset")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://lore.kernel.org/r/091394ea4e705fbb35f828011d98d0ba33808f69.1661257293.git.lorenzo@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Add link_id parameter to cfg80211_ch_switch_started_notify() to allow
driver to indicate on which link channel switch started on MLD.
Send the data to userspace so it knows as well.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Link: https://lore.kernel.org/r/20220722131143.3438042-1-quic_vjakkam@quicinc.com
Link: https://lore.kernel.org/r/20220722131143.3438042-2-quic_vjakkam@quicinc.com
[squash two patches]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
