| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mike Snitzer:
- DM raid target (and MD raid) fix for reconfig_mutex MD deadlock that
should have been merged along with recent v6.7-rc6 MD fixes (see MD
related commits: f2d87a759f68^..b39113349de6)
- DM integrity target fix to avoid modifying immutable biovec in the
integrity_metadata() edge case where kmalloc fails.
- Fix drivers/md/Kconfig so DM_AUDIT depends on BLK_DEV_DM.
- Update DM entry in MAINTAINERS to remove stale info.
* tag 'dm-6.7/dm-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
MAINTAINERS: remove stale info for DEVICE-MAPPER
dm audit: fix Kconfig so DM_AUDIT depends on BLK_DEV_DM
dm-integrity: don't modify bio's immutable bio_vec in integrity_metadata()
dm-raid: delay flushing event_work() after reconfig_mutex is released
|
|
Because some platform Bluetooth will have many background scan when idle.
And the frequently Bluetooth scan will break Wi-Fi traffic many times at
a short duration, it will make Wi-Fi throughput become lower. This patch
will shorter Bluetooth slot and adjust priority settings, make Wi-Fi can
have a more completed duration to do traffic.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20231218061341.51255-12-pkshih@realtek.com
|
|
More readable on the coexistence log.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20231218061341.51255-11-pkshih@realtek.com
|
|
Coexistence will set the RF parameter according to Wi-Fi link mode,
Wi-Fi/Bluetooth signal level, traffic direction, antenna type,
and is there Bluetooth connection exist or not. Bluetooth will notify
the current LNA level by scoreboard. If the setting not as expected,
coexistence will try to assign the correct level.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20231218061341.51255-10-pkshih@realtek.com
|
|
In order to control RF LNA setting, need Bluetooth RSSI level information.
RSSI level separate Bluetooth RSSI to several level, so the mechanism can
assign a corresponding setting.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20231218061341.51255-9-pkshih@realtek.com
|
|
To avoid Bluetooth reconnecting/pairing fail during Wi-Fi is link/scan,
especially the Bluetooth connect event after the platform restart/boot up.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20231218061341.51255-8-pkshih@realtek.com
|
|
Including Wi-Fi RF mode to judge is Wi-Fi RF still on or off,
if Wi-Fi is RF off should set scoreboard to let Bluetooth know
Wi-Fi has gone. Every time the Wi-Fi radio state changed firmware
should force execute refresh the TDMA coexistence mechanism to
prevent incorrect mechanism runs at mismatch state. The coexistence
antenna/TDMA settings should consider what the Wi-Fi mode it is now,
this can help to solve some LPS transient state issue like A2DP
slightly glitch.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20231218061341.51255-7-pkshih@realtek.com
|
|
This can help to debug the grant signal and antenna path control issue
during Wi-Fi power saving mode.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20231218061341.51255-6-pkshih@realtek.com
|
|
BTG is a RF system type, it means Wi-Fi 2.4GHz and Bluetooth share RF gain
and antenna. The RF gain must control by Wi-Fi or Bluetooth in single side.
For example, if Bluetooth RX a very strong signal, then Bluetooth will
adjust to a lower gain. And Wi-Fi will also use the same gain to do RX,
then maybe the gain will not enough. This BTG control mechanism can do
some refine to this situation.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20231218061341.51255-5-pkshih@realtek.com
|
|
Pre-AGC(Auto gain control) is a hardware mechanism, it will auto adjust
the RX gain for every packet, it can help to keep Wi-Fi signal on a well
RX quality. The coexistence will give advice to control the API and
monitor the settings by firmware report.
Also add function to check register, these registers were monitoring
by Wi-Fi firmware and report to coexistence driver periodically. This
can help to track whether these settings were taking effect or not.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20231218061341.51255-4-pkshih@realtek.com
|
|
This information will use as judgment about how to set RF/HW parameters.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20231218061341.51255-3-pkshih@realtek.com
|
|
The Wi-Fi firmware 29.29.X should use version 2 role info format. FDDT
mechanism version 5 use the same cell members to judge traffic situation,
don't need to add another new format.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20231218061341.51255-2-pkshih@realtek.com
|
|
scripts/kernel-doc warns about using @args: for variadic arguments to
functions. Documentation/doc-guide/kernel-doc.rst says that this should
be written as @...: instead, so update the source code to match that,
preventing the warnings.
trace_events_synth.c:1165: warning: Excess function parameter 'args' description in '__synth_event_gen_cmd_start'
trace_events_synth.c:1714: warning: Excess function parameter 'args' description in 'synth_event_trace'
Link: https://lore.kernel.org/linux-trace-kernel/20231220061226.30962-1-rdunlap@infradead.org
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Fixes: 35ca5207c2d11 ("tracing: Add synthetic event command generation functions")
Fixes: 8dcc53ad956d2 ("tracing: Add synth_event_trace() and related functions")
Acked-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
|
|
Currently %ld format specifiers are being used for unsigned long
values. Fix this by using %lu instead. Cleans up cppcheck warnings:
warning: %ld in format string (no. 1) requires 'long' but the argument
type is 'unsigned long'. [invalidPrintfArgType_sint]
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://lore.kernel.org/bpf/20231219152307.368921-1-colin.i.king@gmail.com
|
|
This patch fix the warning introduced by mt6360 node in
mt8395-genio-1200-evk.dts.
arch/arm64/boot/dts/mediatek/mt8195.dtsi:464.4-27: Warning (interrupts_property): /soc/i2c@11d01000/pmic@34:#interrupt-cells: size is (8), expected multiple of 16
Add a missing 'interrupt-parent' to fix this warning.
Fixes: f2b543a191b6 ("arm64: dts: mediatek: add device-tree for Genio 1200 EVK board")
Reported-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/linux-devicetree/20231212214737.230115-1-arnd@kernel.org/
Signed-off-by: Macpaul Lin <macpaul.lin@mediatek.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
NFT_MSG_DELSET deactivates all elements in the set, skip
set->ops->commit() to avoid the unnecessary clone (for the pipapo case)
as well as the sync GC cycle, which could deactivate again expired
elements in such set.
Fixes: 5f68718b34a5 ("netfilter: nf_tables: GC transaction API to avoid race with control plane")
Reported-by: Kevin Rich <kevinrich1337@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
When mgag200 switched from simple KMS to regular atomic helpers,
the initialization of the gamma settings was lost.
This leads to a black screen, if the bios/uefi doesn't use the same
pixel color depth.
This has been fixed with commit ad81e23426a6 ("drm/mgag200: Fix gamma
lut not initialized.") for most G200, but G200ER, G200EV, G200SE use
their own version of crtc_helper_atomic_enable() and need to be fixed
too.
Fixes: 1baf9127c482 ("drm/mgag200: Replace simple-KMS with regular atomic helpers")
Cc: <stable@vger.kernel.org> #v6.1+
Reported-by: Roger Sewell <roger.sewell@cantab.net>
Suggested-by: Roger Sewell <roger.sewell@cantab.net>
Signed-off-by: Jocelyn Falempe <jfalempe@redhat.com>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20231214163849.359691-1-jfalempe@redhat.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/fixes
Fix for occasional boot hang for am335x USB
A fix for occasional boot hang for am335x USB that I've only recently
started noticing.
This can be merged naturally whenever suitable. This issue has been seen
with other similar SoCs earlier and has clearly existed for a long time.
* tag 'am3-usb-hang-fix-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: Fix occasional boot hang for am3 usb
Link: https://lore.kernel.org/r/pull-1703071616-395333@atomide.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/fixes
Fixes for omaps
A few fixes for omaps:
- A regression fix for ti-sysc interconnect target module driver to not access
registers after reset if srst_udelay quirk is needed
- DRA7 L3 NoC node register size fix
* tag 'omap-for-v6.7/fixes-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Fix null pointer dereference and memory leak in omap_soc_device_init
ARM: dts: dra7: Fix DRA7 L3 NoC node register size
bus: ti-sysc: Flush posted write only after srst_udelay
Link: https://lore.kernel.org/r/pull-1702037799-781982@atomide.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Invert the register value for PIN_CONFIG_OUTPUT_ENABLE to return
the opposite of PIN_CONFIG_INPUT_ENABLE.
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Link: https://lore.kernel.org/r/20231219125120.4028862-3-patrick.rudolph@9elements.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Commit 1fa3df901f2c ("pinctrl: cy8c95x0: Remove custom ->set_config()")
removed support for PIN_CONFIG_INPUT_ENABLE and
PIN_CONFIG_OUTPUT.
Add the following options to restore functionality:
- PIN_CONFIG_INPUT_ENABLE
- PIN_CONFIG_OUTPUT_ENABLE
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Link: https://lore.kernel.org/r/20231219125120.4028862-2-patrick.rudolph@9elements.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Fix typo to make pinctrl-cy8c95x compile again.
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Link: https://lore.kernel.org/r/20231219125120.4028862-1-patrick.rudolph@9elements.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
In the afs dynamic root directory, the ->lookup() function does a DNS check
on the cell being asked for and if the DNS upcall reports an error it will
report an error back to userspace (typically ENOENT).
However, if a failed DNS upcall returns a new-style result, it will return
a valid result, with the status field set appropriately to indicate the
type of failure - and in that case, dns_query() doesn't return an error and
we let stat() complete with no error - which can cause confusion in
userspace as subsequent calls that trigger d_automount then fail with
ENOENT.
Fix this by checking the status result from a valid dns_query() and
returning an error if it indicates a failure.
Fixes: bbb4c4323a4d ("dns: Allow the dns resolver to retrieve a server set")
Reported-by: Markus Suvanto <markus.suvanto@gmail.com>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=216637
Signed-off-by: David Howells <dhowells@redhat.com>
Tested-by: Markus Suvanto <markus.suvanto@gmail.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
|
|
Fix the afs dynamic root's d_delete function to always delete unused
dentries rather than only deleting them if they're positive. With things
as they stand upstream, negative dentries stemming from failed DNS lookups
stick around preventing retries.
Fixes: 66c7e1d319a5 ("afs: Split the dynroot stuff out and give it its own ops tables")
Signed-off-by: David Howells <dhowells@redhat.com>
Tested-by: Markus Suvanto <markus.suvanto@gmail.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
|
|
Victor Nogueira says:
====================
net: sched: Make tc-related drop reason more flexible for remaining qdiscs
This patch builds on Daniel's patch[1] to add initial support of tc drop
reason. The main goal is to distinguish between policy and error drops for
the remainder of the egress qdiscs (other than clsact).
The drop reason is set by cls_api and act_api in the tc skb cb in case
any error occurred in the data path.
Also add new skb drop reasons that are idiosyncratic to TC.
[1] https://lore.kernel.org/all/20231009092655.22025-1-daniel@iogearbox.net
Changes in V5:
- Drop "EXT_" from cookie error's drop reason name in doc
Changes in V4:
- Condense all the cookie drop reasons into one
Changes in V3:
- Removed duplicate assignment
- Rename function tc_skb_cb_drop_reason to tcf_get_drop_reason
- Move zone field upwards in struct tc_skb_cb to move hole to the end of
the struct
Changes in V2:
- Dropped RFC tag
- Removed check for drop reason being overwritten by filter in cls_api.c
- Simplified logic and removed function tcf_init_drop_reason
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Continue expanding Daniel's patch by adding new skb drop reasons that
are idiosyncratic to TC.
More specifically:
- SKB_DROP_REASON_TC_COOKIE_ERROR: An error occurred whilst
processing a tc ext cookie.
- SKB_DROP_REASON_TC_CHAIN_NOTFOUND: tc chain lookup failed.
- SKB_DROP_REASON_TC_RECLASSIFY_LOOP: tc exceeded max reclassify loop
iterations
Signed-off-by: Victor Nogueira <victor@mojatatu.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Incrementing on Daniel's patch[1], make tc-related drop reason more
flexible for remaining qdiscs - that is, all qdiscs aside from clsact.
In essence, the drop reason will be set by cls_api and act_api in case
any error occurred in the data path. With that, we can give the user more
detailed information so that they can distinguish between a policy drop
or an error drop.
[1] https://lore.kernel.org/all/20231009092655.22025-1-daniel@iogearbox.net
Signed-off-by: Victor Nogueira <victor@mojatatu.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move drop_reason from struct tcf_result to skb cb - more specifically to
struct tc_skb_cb. With that, we'll be able to also set the drop reason for
the remaining qdiscs (aside from clsact) that do not have access to
tcf_result when time comes to set the skb drop reason.
Signed-off-by: Victor Nogueira <victor@mojatatu.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This adds support for the LED's on most chip versions. Excluded are
the old non-PCIe versions and RTL8125. RTL8125 has a different LED
register layout, support for it will follow later.
LED's can be controlled from userspace using the netdev LED trigger.
Tested on RTL8168h.
Note: The driver can't know which LED's are actually physically
wired. Therefore not every LED device may represent a physically
available LED.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Ido Schimmel says:
====================
Add MDB bulk deletion support
This patchset adds MDB bulk deletion support, allowing user space to
request the deletion of matching entries instead of dumping the entire
MDB and issuing a separate deletion request for each matching entry.
Support is added in both the bridge and VXLAN drivers in a similar
fashion to the existing FDB bulk deletion support.
The parameters according to which bulk deletion can be performed are
similar to the FDB ones, namely: Destination port, VLAN ID, state (e.g.,
"permanent"), routing protocol, source / destination VNI, destination IP
and UDP port. Flushing based on flags (e.g., "offload", "fast_leave",
"added_by_star_ex", "blocked") is not currently supported, but can be
added in the future, if a use case arises.
Patch #1 adds a new uAPI attribute to allow specifying the state mask
according to which bulk deletion will be performed, if any.
Patch #2 adds a new policy according to which bulk deletion requests
(with 'NLM_F_BULK' flag set) will be parsed.
Patches #3-#4 add a new NDO for MDB bulk deletion and invoke it from the
rtnetlink code when a bulk deletion request is made.
Patches #5-#6 implement the MDB bulk deletion NDO in the bridge and
VXLAN drivers, respectively.
Patch #7 allows user space to issue MDB bulk deletion requests by no
longer rejecting the 'NLM_F_BULK' flag when it is set in 'RTM_DELMDB'
requests.
Patches #8-#9 add selftests for both drivers, for both good and bad
flows.
iproute2 changes can be found here [1].
https://github.com/idosch/iproute2/tree/submit/mdb_flush_v1
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add test cases to verify the behavior of the MDB bulk deletion
functionality in the VXLAN driver.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Petr Machata <petrm@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add test cases to verify the behavior of the MDB bulk deletion
functionality in the bridge driver.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Hangbin Liu <liuhangbin@gmail.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that both the common code as well as individual drivers support MDB
bulk deletion, allow user space to make such requests.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Implement MDB bulk deletion support in the VXLAN driver, allowing MDB
entries to be deleted in bulk according to provided parameters.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Implement MDB bulk deletion support in the bridge driver, allowing MDB
entries to be deleted in bulk according to provided parameters.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Invoke the new MDB bulk deletion device operation when the 'NLM_F_BULK'
flag is set in the netlink message header.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add MDB net device operation that will be invoked by rtnetlink code in
response to received 'RTM_DELMDB' messages with the 'NLM_F_BULK' flag
set. Subsequent patches will implement the operation in the bridge and
VXLAN drivers.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For MDB bulk delete we will need to validate 'MDBA_SET_ENTRY'
differently compared to regular delete. Specifically, allow the ifindex
to be zero (in case not filtering on bridge port) and force the address
to be zero as bulk delete based on address is not supported.
Do that by introducing a new policy and choosing the correct policy
based on the presence of the 'NLM_F_BULK' flag in the netlink message
header. Use nlmsg_parse() for strict validation.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, the 'state' field in 'struct br_port_msg' can be set to 1 if
the MDB entry is permanent or 0 if it is temporary. Additional states
might be added in the future.
In a similar fashion to 'NDA_NDM_STATE_MASK', add an MDB state mask uAPI
attribute that will allow the upcoming bulk deletion API to bulk delete
MDB entries with a certain state or any state.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The driver should continue get the timestamp if STMMAC_FLAG_EXT_SNAPSHOT_EN
flag is set.
Fixes: aa5513f5d95f ("net: stmmac: replace the ext_snapshot_en field with a flag")
Cc: <stable@vger.kernel.org> # 6.6
Signed-off-by: Song Yoong Siang <yoong.siang.song@intel.com>
Signed-off-by: Lai Peter Jun Ann <jun.ann.lai@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Maintain Consistent Formatting: Insert Space after #include
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Wang Jinchao <wangjinchao@xfusion.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth
Luiz Augusto von Dentz says:
====================
bluetooth pull request for net:
- Add encryption key size check when acting as peripheral
- Shut up false-positive build warning
- Send reject if L2CAP command request is corrupted
- Fix Use-After-Free in bt_sock_recvmsg
- Fix not notifying when connection encryption changes
- Fix not checking if HCI_OP_INQUIRY has been sent
- Fix address type send over to the MGMT interface
- Fix deadlock in vhci_send_frame
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Before this patch, transport offset (pkt->thoff) provides an offset
relative to the network header. This is fine for the inet families
because skb->data points to the network header in such case. However,
from netdev/egress, skb->data points to the mac header (if available),
thus, pkt->thoff is missing the mac header length.
Add skb_network_offset() to the transport offset (pkt->thoff) for
netdev, so transport header mangling works as expected. Adjust payload
fast eval function to use skb->data now that pkt->thoff provides an
absolute offset. This explains why users report that matching on
egress/netdev works but payload mangling does not.
This patch implicitly fixes payload mangling for IPv4 packets in
netdev/egress given skb_store_bits() requires an offset from skb->data
to reach the transport header.
I suspect that nft_exthdr and the trace infra were also broken from
netdev/egress because they also take skb->data as start, and pkt->thoff
was not correct.
Note that IPv6 is fine because ipv6_find_hdr() already provides a
transport offset starting from skb->data, which includes
skb_network_offset().
The bridge family also uses nft_set_pktinfo_ipv4_validate(), but there
skb_network_offset() is zero, so the update in this patch does not alter
the existing behaviour.
Fixes: 42df6e1d221d ("netfilter: Introduce egress hook")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
There is error log when htab-mem benchmark completes. The error log
looks as follows:
$ ./bench htab-mem -d1
Setting up benchmark 'htab-mem'...
Benchmark 'htab-mem' started.
......
(cgroup_helpers.c:353: errno: Device or resource busy) umount cgroup2
Fix it by closing cgrp fd before invoking cleanup_cgroup_environment().
Signed-off-by: Hou Tao <houtao1@huawei.com>
Link: https://lore.kernel.org/r/20231219135727.2661527-1-houtao@huaweicloud.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Andrii Nakryiko says:
====================
Enhance BPF global subprogs with argument tags
This patch set adds verifier support for annotating user's global BPF subprog
arguments with few commonly requested annotations, to improve global subprog
verification experience.
These tags are:
- ability to annotate a special PTR_TO_CTX argument;
- ability to annotate a generic PTR_TO_MEM as non-null.
We utilize btf_decl_tag attribute for this and provide two helper macros as
part of bpf_helpers.h in libbpf (patch #8).
Besides this we also add abilit to pass a pointer to dynptr into global
subprog. This is done based on type name match (struct bpf_dynptr *). This
allows to pass dynptrs into global subprogs, for use cases that deal with
variable-sized generic memory pointers.
Big chunk of the patch set (patches #1 through #5) are various refactorings to
make verifier internals around global subprog validation logic easier to
extend and support long term, eliminating BTF parsing logic duplication,
factoring out argument expectation definitions from BTF parsing, etc.
New functionality is added in patch #6 (ctx and non-null) and patch #7
(dynptr), extending global subprog checks with awareness for arg tags.
Patch #9 adds simple tests validating each of the added tags and dynptr
argument passing.
Patch #10 adds a simple negative case for freplace programs to make sure that
target BPF programs with "unreliable" BTF func proto cannot be freplaced.
v2->v3:
- patch #10 improved by checking expected verifier error (Eduard);
v1->v2:
- dropped packet args for now (Eduard);
- added back unreliable=true detection for entry BPF programs (Eduard);
- improved subprog arg validation (Eduard);
- switched dynptr arg from tag to just type name based check (Eduard).
====================
Link: https://lore.kernel.org/r/20231215011334.2307144-1-andrii@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Add a test validating that freplace'ing another main (entry) BPF program
fails if the target BPF program doesn't have valid/expected func proto BTF.
We extend fexit_bpf2bpf test to allow to specify expected log message
for negative test cases (where freplace program is expected to fail to
load).
Acked-by: Eduard Zingerman <eddyz87@gmail.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/r/20231215011334.2307144-11-andrii@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Add test cases to validate semantics of global subprog argument
annotations:
- non-null pointers;
- context argument;
- const dynptr passing;
- packet pointers (data, metadata, end).
Acked-by: Eduard Zingerman <eddyz87@gmail.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/r/20231215011334.2307144-10-andrii@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Add a set of __arg_xxx macros which can be used to augment BPF global
subprogs/functions with extra information for use by BPF verifier.
Acked-by: Eduard Zingerman <eddyz87@gmail.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/r/20231215011334.2307144-9-andrii@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Add ability to pass a pointer to dynptr into global functions.
This allows to have global subprogs that accept and work with generic
dynptrs that are created by caller. Dynptr argument is detected based on
the name of a struct type, if it's "bpf_dynptr", it's assumed to be
a proper dynptr pointer. Both actual struct and forward struct
declaration types are supported.
This is conceptually exactly the same semantics as
bpf_user_ringbuf_drain()'s use of dynptr to pass a variable-sized
pointer to ringbuf record. So we heavily rely on CONST_PTR_TO_DYNPTR
bits of already existing logic in the verifier.
During global subprog validation, we mark such CONST_PTR_TO_DYNPTR as
having LOCAL type, as that's the most unassuming type of dynptr and it
doesn't have any special helpers that can try to free or acquire extra
references (unlike skb, xdp, or ringbuf dynptr). So that seems like a safe
"choice" to make from correctness standpoint. It's still possible to
pass any type of dynptr to such subprog, though, because generic dynptr
helpers, like getting data/slice pointers, read/write memory copying
routines, dynptr adjustment and getter routines all work correctly with
any type of dynptr.
Acked-by: Eduard Zingerman <eddyz87@gmail.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/r/20231215011334.2307144-8-andrii@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Add support for annotating global BPF subprog arguments to provide more
information about expected semantics of the argument. Currently,
verifier relies purely on argument's BTF type information, and supports
three general use cases: scalar, pointer-to-context, and
pointer-to-fixed-size-memory.
Scalar and pointer-to-fixed-mem work well in practice and are quite
natural to use. But pointer-to-context is a bit problematic, as typical
BPF users don't realize that they need to use a special type name to
signal to verifier that argument is not just some pointer, but actually
a PTR_TO_CTX. Further, even if users do know which type to use, it is
limiting in situations where the same BPF program logic is used across
few different program types. Common case is kprobes, tracepoints, and
perf_event programs having a helper to send some data over BPF perf
buffer. bpf_perf_event_output() requires `ctx` argument, and so it's
quite cumbersome to share such global subprog across few BPF programs of
different types, necessitating extra static subprog that is context
type-agnostic.
Long story short, there is a need to go beyond types and allow users to
add hints to global subprog arguments to define expectations.
This patch adds such support for two initial special tags:
- pointer to context;
- non-null qualifier for generic pointer arguments.
All of the above came up in practice already and seem generally useful
additions. Non-null qualifier is an often requested feature, which
currently has to be worked around by having unnecessary NULL checks
inside subprogs even if we know that arguments are never NULL. Pointer
to context was discussed earlier.
As for implementation, we utilize btf_decl_tag attribute and set up an
"arg:xxx" convention to specify argument hint. As such:
- btf_decl_tag("arg:ctx") is a PTR_TO_CTX hint;
- btf_decl_tag("arg:nonnull") marks pointer argument as not allowed to
be NULL, making NULL check inside global subprog unnecessary.
Acked-by: Eduard Zingerman <eddyz87@gmail.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/r/20231215011334.2307144-7-andrii@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
