| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Seaboard uses a TPS6586x regulator. Instantiate this, and hook up a
couple of fixed GPIO-controlled regulators too.
Two data sources were used for the data encoded here:
* The HW defaults, as extracted from real HW.
* The schematic, which specifies a voltage for each LDO rail.
In most cases these sources matched. The only differences is:
ldo6: The HW default on Springbank is 2.85v. The HW default on Seaboard
is 1.8v. The schematics for both Springbank and Seaboard match at 2.85v.
However, internal research indicates that the schematics are incorrectly
labelled, and 1.8v is correct. The ChromeOS kernel also uses 1.8v.
Note that these settings don't entirely match those in the ChromeOS
kernel found at the URL below. However, the selected values generally
cause no behavior change in the kernel, and so were picked to avoid
regressions.
repo http://git.chromium.org/chromiumos/third_party/kernel.git
branch chromeos-3.2
file arch/arm/mach-tegra/board-seaboard-power.c
Portions based on work by Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
Cadhu have multiple power rails which are controlled by
GPIOs. Add support of these power rail control through
fixed regulators. Add entry for all fixed regulators for
cardhu-a02 and a04.
The details are taken from downstream kernel.
Some points on this change are:
* Add the tps65910-LDO5 entry and make it always ON
to supply power to SDMMC. Once the sd driver support
regulator handling, this flag will be remove.
* Dropping registration of rail vdd_sdmmc1 as the gpio
is used by sdhci power-gpio. This need to fix in
sdhci driver and then need to add the registration
mechanism. Just removing power-gpio and adding fixed
regulator with this gpio is causing the sd access to
fail because first probe call of this regulator fails
due to non-available of parent and so it calls
gpio_free() which disable the pins in gpio mode make
pin output to LOW causes power to OFF. In probe retry,
it got success and it powered-on but it again need to
do again numeration of card here.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
There is multiple version of cardhu starting from A01 to A07.
Cardhu A01 and A03 are not supported. Cardhu A02 will have
different sets of GPIOs for fixed regulator compare to
cardhu A04. The Cardhu A05, A06, A07 are compatibe with A04.
Based on cardhu version, the related dts file need to be chosen
like for cardhu A02, use tegra30-cardhu-a02.dts, cardhu A04 and
more, use tegra30-cardhu-a04.dts.
This patch create the DTS file A02 and A04 and convert tegra30-cardhu.dts
as dts include file.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
Tegra30 based platform "cardhu" have the power management
IC TPS65911 for the regulator.
Adding DT entry for this device.
Data are chosen from downstream kernel and making the
voltage output as require by default for device to
operate.
The default interrupt line is HIGH from PMIC device and so
inverting the interrupt detection line of PMU interrupt
through configuring PMC.
In this patch, do not registering LDO5 because the input
supply for this rail is different for different version of
cardhu i..e A02 and A04. The registration will be done once
the dts file for cardhu A02 and A04 are added in follow on
patches.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
tegra_time is a struct sys_timer, not a struct clk, so can't be included
in an array of struct clk *.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
It should use tegra30_audio_sync_clk_ops for tegra30. It will cause
the tegra30 use the wrong audio_sync_clk_ops when build a kernel with
a tegra20 and tegra30 both supported kernel. And building error when
a tegra30-only kernel.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
Currently the tegra20 and tegra30 share the same symbol for
tegra_clk_32k_ops. This will cause a compile error when building
a tegra20-only kernel image. Add tegra_clk_32k_ops for tegra20 and
modify tegra30_clk_32k_ops for tegra30.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
Remove Tegra legacy clock framework code.
Signed-off-by: Prashant Gaikwad <pgaikwad@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
This patch converts tegra clock code to generic clock framework in following way:
- Implement clk_ops as required by generic clk framework. (tegraXX_clocks.c)
- Use platform specific struct clk_tegra in clk_ops implementation instead of struct clk.
- Initialize all clock data statically. (tegraXX_clocks_data.c)
Legacy framework did not have recalc_rate and is_enabled functions. Implemented these functions.
Removed init function. It's functionality is splitted into recalc_rate and is_enabled.
Static initialization is used since slab is not up in .init_early and clock
is needed to be initialized before clockevent/clocksource initialization.
Macros redefined for clk_tegra.
Also, single struct clk_tegra is used for all type of clocks (PLL, peripheral etc.). This
is to move quickly to generic common clock framework so that other dependent features will
not be blocked (such as DT binding).
Enabling COMMON_CLOCK config moved to ARCH_TEGRA since it is enabled for both Tegra20
and Tegra30.
Signed-off-by: Prashant Gaikwad <pgaikwad@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
Add Tegra platform specific clock structure clk_tegra and
some helper functions for generic clock framework.
struct clk_tegra is the single strcture used for all types of
clocks. reset and cfg_ex ops moved to clk_tegra from clk_ops.
Signed-off-by: Prashant Gaikwad <pgaikwad@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
Make the name consistent with other files.
s/tegra2/tegra20
Signed-off-by: Prashant Gaikwad <pgaikwad@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
Move clock initialization data to separate file. This is
required for migrating to generic clock framework if static
initialization is used.
Signed-off-by: Prashant Gaikwad <pgaikwad@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
Move clock initialization data to separate file. This is
required for migrating to generic clock framework if static
initialization is used.
Signed-off-by: Prashant Gaikwad <pgaikwad@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
A U16 divider can divide a clock by 1..64K. However, the range-check
in clk_div16_get_divider() limited the range to 1..256. Fix this. NVIDIA's
downstream kernels already have the fixed range-check.
In practice this is a problem on Whistler's I2C bus, which uses a bus
clock rate of 100KHz (rather than the more common 400KHz on Tegra boards),
which requires a HW module clock of 8*100KHz. The parent clock is 216MHz,
leading to a desired divider of 270. Prior to conversion to the common
clock framework, this range error was somehow ignored/irrelevant and
caused no problems. However, the common clock framework evidently has
more rigorous error-checking, so this failure causes the I2C bus to fail
to operate correctly.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
Some boards use UART D for the main serial console, and some use UART A.
UART D's clock is listed in board-dt-tegra20.c's clock table, whereas
UART A's clock is not. This causes the clock code to think UART A's
clock is unsed. The common clock framework turns off unused clocks at
boot time. This makes the kernel appear to hang. Add UART A's clock into
the clock table to prevent this. Eventually, this requirement should be
handled by the UART driver, and/or properties in a board-specific device
tree file.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
Nothing from this file is needed, so remove the include. This helps
single zImage work by reducing use of the mach-tegra/include/mach/
directory.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Chris Ball <cjb@laptop.org>
|
|
Nothing from these files is needed, so remove the includes. This helps
single zImage work by reducing use of the mach-tegra/include/mach/
directory.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
|
|
ARCH_TEGRA (arch/arm/Kconfig) now selects USE_OF, so there's not need
for ARCH_TEGRA_3x_SOC to do so too.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
Use macro IO_ADDRESS for getting virtual address of
corresponding physical address to make the consistency
with rest of Tegra code-base.
This macro calls the IO_TO_VIRT() which is defined in
arch/arm/mach-tegra/include/mach/iomap.h
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
Signed-off-by: Pavel Shilovsky <pshilovsky@etersoft.ru>
Signed-off-by: Steve French <smfrench@gmail.com>
|
|
Cc: <stable@vger.kernel.org>
Signed-off-by: Pavel Shilovsky <pshilovsky@etersoft.ru>
Signed-off-by: Steve French <smfrench@gmail.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC bug fixes from Olof Johansson:
"Mostly Renesas and Atmel bugfixes this time, targeting boot and build
problems. A couple of patches for gemini and kirkwood as well. On a
whole nothing very controversial."
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: gemini: fix the gemini build
ARM: shmobile: armadillo800eva: enable rw rootfs mount
ARM: Kirkwood: Fix 'SZ_1M' undeclared here for db88f6281-bp-setup.c
ARM: shmobile: mackerel: fixup usb module order
ARM: shmobile: armadillo800eva: fixup: sound card detection order
ARM: shmobile: marzen: fixup smsc911x id for regulator
ARM: at91/feature-removal-schedule: delay at91_mci removal
ARM: mach-shmobile: armadillo800eva: Enable power button as wakeup source
ARM: mach-shmobile: armadillo800eva: Fix GPIO buttons descriptions
ARM: at91/dts: remove partial parameter in at91sam9g25ek.dts
ARM: at91/clock: fix PLLA overclock warning
ARM: at91: fix rtc-at91sam9 irq issue due to sparse irq support
ARM: at91: fix system timer irq issue due to sparse irq support
ARM: shmobile: sh73a0: fixup RELOC_BASE of intca_irq_pins_desc
|
|
Fengguang Wu <fengguang.wu@intel.com> writes:
> After the __devinit* removal series, I can still get kernel panic in
> show_uevent(). So there are more sources of bug..
>
> Debug patch:
>
> @@ -343,8 +343,11 @@ static ssize_t show_uevent(struct device
> goto out;
>
> /* copy keys to file */
> - for (i = 0; i < env->envp_idx; i++)
> + dev_err(dev, "uevent %d env[%d]: %s/.../%s\n", env->buflen, env->envp_idx, top_kobj->name, dev->kobj.name);
> + for (i = 0; i < env->envp_idx; i++) {
> + printk(KERN_ERR "uevent %d env[%d]: %s\n", (int)count, i, env->envp[i]);
> count += sprintf(&buf[count], "%s\n", env->envp[i]);
> + }
>
> Oops message, the env[] is again not properly initilized:
>
> [ 44.068623] input input0: uevent 61 env[805306368]: input0/.../input0
> [ 44.069552] uevent 0 env[0]: (null)
This is a completely different CONFIG_HOTPLUG problem, only
demonstrating another reason why CONFIG_HOTPLUG should go away. I had a
hard time trying to disable it anyway ;-)
The problem this time is lots of code assuming that a call to
add_uevent_var() will guarantee that env->buflen > 0. This is not true
if CONFIG_HOTPLUG is unset. So things like this end up overwriting
env->envp_idx because the array index is -1:
if (add_uevent_var(env, "MODALIAS="))
return -ENOMEM;
len = input_print_modalias(&env->buf[env->buflen - 1],
sizeof(env->buf) - env->buflen,
dev, 0);
Don't know what the best action is, given that there seem to be a *lot*
of this around the kernel. This patch "fixes" the problem for me, but I
don't know if it can be considered an appropriate fix.
[ It is the correct fix for now, for 3.7 forcing CONFIG_HOTPLUG to
always be on is the longterm fix, but it's too late for 3.6 and older
kernels to resolve this that way - gregkh ]
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Tested-by: Fengguang Wu <fengguang.wu@intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If xfernotready is received and there is no request in request_list then
REQUEST_PENDING flag must be set, so that next request in ep queue is executed.
In case of isoc transfer, if xfernotready is already elapsed and even first
request has not been queued to request_list, then issue END TRANSFER, so that
you can receive xfernotready again and can have notion of current microframe.
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
renesas_usbhs dma can transport 8byte alignment data, not 4byte.
This patch fixup it.
Reported-by: Sugnan Prabhu S <sugnan.prabhu@renesasmobile.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Earlier we used to check for ep->ep.desc to figure out if this ep has
already been enabled and if so, abort.
Ido Shayevitz removed the usb_endpoint_descriptor from private udc
structure 5a6506f00 ("usb: gadget: Update at91_udc to use
usb_endpoint_descriptor inside the struct usb_ep") but did not fix up
the ep_enable condition because _now_ the member is always true and we
can't check if this ep is enabled twice.
Cc: Ido Shayevitz <idos@codeaurora.org>
Tested-by: Fabio Porcedda <fabio.porcedda@gmail.com>
Tested-by: Mario Isidoro <Mario.Isidoro@tecmic.pt>
Cc: <stable@kernel.org> # v3.5
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
The driver was converted to the new start/stop interface in f3d8bf34c2
("usb: gadget: at91_udc: convert to new style start/stop interface").
I overlooked that the driver is overwritting the private data which is
used by the composite framework. The udc driver doesn't read it, it is
only written here.
Tested-by: Fabio Porcedda <fabio.porcedda@gmail.com>
Tested-by: Mario Isidoro <Mario.Isidoro@tecmic.pt>
Cc: <stable@kernel.org> # v3.5
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Populate the resources for xhci afresh instead of directly using the
*struct resource* of core. *resource* structure has parent, sibling,
child pointers which should be filled only by resource API's. By
directly using the *resource* pointer of core in xhci, these parent,
sibling, child pointers are already populated even before
*platform_device_add* causing side effects.
Cc: stable@vger.kernel.org # v3.4, v3.5
Reported-by: Ruchika Kharwar <ruchika@ti.com>
Tested-by: Moiz Sonasath <m-sonasath@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
dma_controller_create() in this MUSB DMA driver only regards 0 as a wrong IRQ
number, despite platform_get_irq_byname() that it calls returns -ENXIO in that
case. It leads to calling request_irq() with a negative IRQ number, and when it
naturally fails, the following is printed to the console:
request_irq -6 failed!
and the DMA controller is not created.
Fix this function to filter out the error values as well as 0.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
On platform_device_add() failure, the TUSB6010 glue layer forgets to call
platform_device_put() -- probably due to a typo...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
when using musb_urb_enqueue to submit three urbs to the same endpoint, when
hep->hcpriv is NULL, qh will be allocated when the first urb is completed.
When the IRQ completes the next two urbs, qh->hep->hcpriv will be set to NULL.
Now the second urb get musb->lock and executes musb_schedule(), but
next_urb(qh) is NULL, so musb_start_urb will Oops.
[ balbi@ti.com : practically rewrote commit log so it makes sense ]
Signed-off-by: mayuzheng <myz147@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Without a reply for USB_DT_BOS the USB3 mode does not work since
448b6eb1 ("USB: Make sure to fetch the BOS desc for roothubs.).
Cc: stable@vger.kernel.org #v3.5
Signed-off-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
If USB2 host controller probes fine but USB3 does not then we don't
remove the USB controller properly and lock up the system while the HUB
code will try to enumerate the USB2 controller and access memory which
is no longer available in case the dummy_hcd was compiled as a module.
This is a problem since 448b6eb1 ("USB: Make sure to fetch the BOS desc
for roothubs.) if used in USB3 mode because dummy does not provide this
descriptor and explodes later.
Cc: stable@vger.kernel.org # v3.5
Signed-off-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Convert a 0 error return code to a negative one, as returned elsewhere in the
function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier ret;
expression e,e1,e2,e3,e4,x;
@@
(
if (\(ret != 0\|ret < 0\) || ...) { ... return ...; }
|
ret = 0
)
... when != ret = e1
*x = \(kmalloc\|kzalloc\|kcalloc\|devm_kzalloc\|ioremap\|ioremap_nocache\|devm_ioremap\|devm_ioremap_nocache\)(...);
... when != x = e2
when != ret = e3
*if (x == NULL || ...)
{
... when != ret = e4
* return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
In case of ep0 out, if length is not aligned to maxpacket size then we use
dwc->ep_bounce_addr for dma transfer and not request->dma. Since, we have
alreday done memcpy from dwc->ep0_bounce to request->buf, so we do not need to
issue cache sync function. In fact, cache sync function will bring wrong data
in request->buf from request->dma in this scenario.
So, cache sync function must not be executed in case of ep0 bounced.
Cc: <stable@vger.kernel.org> # v3.4 v3.5
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
If f_fs.c and u_serial.c are combined together using #include, which has
been a common practice so far, the pr_vdebug macro is defined multiple
times. Define it only once.
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull a hwmon fix from Guenter Roeck:
"One patch, fixing DIV_ROUND_CLOSEST to support negative dividends.
While the changes are not in the drivers/hwmon directory, the problem
primarily affects hwmon drivers, and it makes sense to push the patch
through the hwmon tree."
* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
linux/kernel.h: Fix DIV_ROUND_CLOSEST to support negative dividends
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild
Pull kbuild fixes from Michal Marek:
"These are two fixes that should go into 3.6. The link-vmlinux.sh one
is obvious.
The other one fixes make firmware_install with certain configurations,
where a file in the toplevel firmware tree gets installed first, and
$(INSTALL_FW_PATH)/$$(dir <file>) results in /lib/firmware/./, which
confuses make 3.82 for some reason."
* 'rc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
firmware: fix directory creation rule matching with make 3.82
link-vmlinux.sh: Fix stray "echo" in error message
|
|
Trivially triggerable, found by trinity:
kernel BUG at mm/mempolicy.c:2546!
Process trinity-child2 (pid: 23988, threadinfo ffff88010197e000, task ffff88007821a670)
Call Trace:
show_numa_map+0xd5/0x450
show_pid_numa_map+0x13/0x20
traverse+0xf2/0x230
seq_read+0x34b/0x3e0
vfs_read+0xac/0x180
sys_pread64+0xa2/0xc0
system_call_fastpath+0x1a/0x1f
RIP: mpol_to_str+0x156/0x360
Cc: stable@vger.kernel.org
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Added file /sys/devices/.../tty/ttySX/uartclk to allow reading
uartclk value in struct uart_port in serial_core via sysfs.
tty_register_device() has been generalized and refactored in order
to add support for setting drvdata and attribute_group to the device.
Signed-off-by: Tomas Hlavacek <tmshlvck@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fixes these build errors:
In file included from drivers/tty/serial/sccnxp.c:20:0:
include/linux/serial_core.h: In function 'uart_handle_break':
include/linux/serial_core.h:543:30: error: dereferencing pointer to incomplete type
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We call the get_device() in the mxs_auart_probe().
For the balance of the reference count, we should put the
device in the mxs_auart_remove().
Signed-off-by: Huang Shijie <shijie8@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
After set the AUART_CTRL0_CLKGATE, the UART will gate all the clocks off.
So the following line will not take effect.
................................................................
writel(AUART_INTR_RXIEN | AUART_INTR_RTIEN | AUART_INTR_CTSMIEN,
u->membase + AUART_INTR_CLR);
................................................................
To fix this issue, the patch moves this gate-off line to
the end of setting registers.
Signed-off-by: Huang Shijie <shijie8@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
sizeof when applied to a pointer typed expression gives the
size of the pointer.
Generated by: scripts/coccinelle/misc/noderef.cocci
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
enable RX FIFO for 16 characters and TX FIFO
for 16 spaces.
Tested-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
nobody needs to access the uart_omap_port structure
other than omap-serial.c file. Let's move that
structure definition to the C source file in order
to prevent anyone from accessing our structure.
Tested-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
this driver doesn't use any from <plat/dmtimer.h>, so
we can remove it without any problems.
This will, however cause a problem because omap-serial.c
was relying on indirect inclusion of <linux/platform_device.h>,
let's fix the issue by including <linux/platform_device.h>
on omap-serial.c as it should be.
Tested-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Software flow control register bits were not defined correctly.
Also clarify the IXON and IXOFF logic to reflect what userspace wants.
Cc: stable@vger.kernel.org
Tested-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
if we would reach serial_omap_get_char() while
Data Ready bit isn't set, we would return from
it without kicking our pm timer. This would mean
we would, eventually, have an unbalanced
pm_runtime_get on our device which would prevent
it from ever sleeping again.
Tested-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This has been missing from OMAP UART driver
for quite a while and it's simple enough
to implement it.
Tested-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
