| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
PMBUS_NO_WRITE_PROTECT and PMBUS_USE_COEFFICIENTS_CMD flags have been added
to pmbus, but the corresponding documentation was not updated.
Update the documentation before adding new flags
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Message-ID: <20241105-tps25990-v4-1-0e312ac70b62@baylibre.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
SY24655: Support for current and voltage detection as well as
power calculation.
Signed-off-by: Wenliang Yan <wenliang202407@163.com>
Message-ID: <20241106150547.2538-1-wenliang202407@163.com>
[groeck: Changed order of compatible entries;
dropped spurious extra return statement in is_visible();
fixed code problems]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
SY24655 is similar to INA226. Its supply voltage and pin definitions
are therefore the same. Compared to INA226, SY24655 has two additional
registers for configuring and calculating average power.
Signed-off-by: Wenliang Yan <wenliang202407@163.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Message-ID: <20241106150547.2538-2-wenliang202407@163.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Add support for LTC7841. The LTC7841 is a high performance
PolyPhase® single output synchronous boost converter controller.
Multiphase operation reduces input and output capacitor
requirements and allows the use of smaller inductors than the
single-phase equivalent.
The relevant registers in the LTC7841 are similar to the
LTC7880, only reduced by some amount. So it's just a matter of adding
the chip id. The device also doesn't support polling, on top of the
reduced register set, so a separate case for setting the chip info is
added.
Signed-off-by: Mariel Tinaco <Mariel.Tinaco@analog.com>
Message-ID: <20241029013734.293024-4-Mariel.Tinaco@analog.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Add LTC7841 to compatible devices of LTC2978
Signed-off-by: Mariel Tinaco <Mariel.Tinaco@analog.com>
Message-ID: <20241029013734.293024-3-Mariel.Tinaco@analog.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Add LTC7841 to supported devices of LTC2978. It has similar set of
registers to LTC7880, differing only in number of output channels and
some unimplemented PMBUS status and functionalities.
Signed-off-by: Mariel Tinaco <Mariel.Tinaco@analog.com>
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Message-ID: <20241029013734.293024-2-Mariel.Tinaco@analog.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The NCT7363Y is a fan controller which provides up to 16
independent FAN input monitors. It can report each FAN input count
values. The NCT7363Y also provides up to 16 independent PWM
outputs. Each PWM can output specific PWM signal by manual mode to
control the FAN duty outside.
Signed-off-by: Ban Feng <kcfeng0@nuvoton.com>
Message-ID: <20241022052905.4062682-3-kcfeng0@nuvoton.com>
[groeck: Dropped unnecessary variable initialization, and , after { }]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Add bindings for the Nuvoton NCT7363Y Fan Controller
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Ban Feng <kcfeng0@nuvoton.com>
Message-ID: <20241022052905.4062682-2-kcfeng0@nuvoton.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Remove vicor,pli1209bc from trivial-devices as it requires additional
properties and does not fit into the trivial devices category.
Add new bindings for Vicor pli1209bc, a Digital Supervisor with
Isolation for use with BCM Bus Converter Modules.
VR rails are defined under regulator node as expected by pmbus driver.
Signed-off-by: Naresh Solanki <naresh.solanki@9elements.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Message-ID: <20241021123044.3648960-1-naresh.solanki@9elements.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Remove mps297x from trivial-devices as it requires
additional properties and does not fit into the trivial
devices category.
Add new bindings for MPS mp2971, mp2973 & mp2975.
It is Dual-Loop, Digital Multi-Phase Controller with PMBUS
interface
Signed-off-by: Naresh Solanki <naresh.solanki@9elements.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Message-ID: <20241022103750.572677-1-naresh.solanki@9elements.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Per his request, remove Aleksandr Mezin as maintainer of the
NZXT-SMART2 hardware monitoring driver.
Cc: Aleksandr Mezin <mezin.alexander@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Boards such as
* Pro WS 665-ACE
* Pro WS 600M-CL
have got a nct6775 chip, but by default there's no use of it
because of resource conflict with WMI method.
Add affected boards to the WMI monitoring list.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=204807
Co-developed-by: Tommy Giesler <tommy.giesler@hetzner.com>
Signed-off-by: Tommy Giesler <tommy.giesler@hetzner.com>
Signed-off-by: Sarah Maedel <sarah.maedel@hetzner-cloud.de>
Message-ID: <20241018074611.358619-1-sarah.maedel@hetzner-cloud.de>
[groeck: Change commit message to imperative mood]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Driver for Renesas ISL28022 power monitor with I2C interface.
The device monitors voltage, current via shunt resistor
and calculated power.
Signed-off-by: Carsten Spieß <mail@carsten-spiess.de>
Signed-off-by: Yikai Tsai <yikai.tsai.wiwynn@gmail.com>
Message-ID: <20241002081133.13123-3-yikai.tsai.wiwynn@gmail.com>
[groeck: Fixed alignment issues, dropped noise at end of probe]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Add dt-bindings for Renesas ISL28022 power monitor.
Signed-off-by: Carsten Spieß <mail@carsten-spiess.de>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Yikai Tsai <yikai.tsai.wiwynn@gmail.com>
Message-ID: <20241002081133.13123-2-yikai.tsai.wiwynn@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
After commit 0edb555a65d1 ("platform: Make platform_driver::remove()
return void") .remove() is (again) the right callback to implement for
platform drivers.
Convert all platform drivers below drivers/hwmonto use .remove(), with
the eventual goal to drop struct platform_driver::remove_new(). As
.remove() and .remove_new() have the same prototypes, conversion is done
by just changing the structure member name in the driver initializer.
While touching these files, make indention of the struct initializer
consistent in several files.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Message-ID: <20241017155900.137357-2-u.kleine-koenig@baylibre.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Add support for manipulating the internal heater of sht4x devices.
Enabling the heater removes condensed water from the sensor surface
which disturbs the relative humidity measurements.
The heater can operate at three heating levels (20, 110 or 200
milliwatts). Also, two heating durations may be selected (0.1 or 1s).
Once the heating time elapses the heater is automatically switched off.
Changes since v3:
* struct sht4x_data: add heating_complete timestamp
* struct sht4x_data: add data_pending flag
* heater_enable_store: return -EINVAL if input != 1
* heater_enable_store: check for data->heating_complete and update it
* heater_enable_store: set data_pending flag after heating request
* sht4x_read_values: msleep if heating in progress
* sht4x_read_values: dont send measurement request if data_pending
* heater_enable attr: make it RW
* Documentation: update info about heater_enable attr
Changes since v2:
* heater_enable_store: remove unnecessary if
* Documentation: remove incorrect info about turning off the heater
* be more specific in the patch description
Changes since v1:
* explain the use case of the new attributes set
* heater_enable attr: make it write-only
* heater_enable_store: define cmd as u8 instead of u8*
* heater_enable_store: remove unreachable data path
* heater_enable_store: remove unnecessary lock
* heater_enable_store: call i2c_master_send only if status==true
* define attributes as DEVICE_ATTR_* instead of SENSOR_DEVICE_ATTR_*
Signed-off-by: Antoni Pokusinski <apokusinski01@gmail.com>
Message-ID: <20240930205346.2147-1-apokusinski01@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Use new member visible of struct hwmon_ops to simplify specifying
the static attribute visibility.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Message-ID: <1ac2be2d-df4f-455a-900d-821fc7bd12c4@gmail.com>
Acked-by: Jonas Malaco <jonas@protocubo.io>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Use new member visible of struct hwmon_ops to simplify specifying
the static attribute visibility.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Message-ID: <8ef99170-b37d-4c9a-b3bf-59f4ea76cf29@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Use new member visible of struct hwmon_ops to simplify specifying
the static attribute visibility.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Message-ID: <4e8893a1-b080-4676-97b9-a48ac9ead28a@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Use new member visible of struct hwmon_ops to simplify specifying
the static attribute visibility.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Thomas Weißschuh <linux@weissschuh.net>
Message-ID: <c4b4568b-59f6-43ac-8281-536a82ecd6ab@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Use new member visible of struct hwmon_ops to simplify specifying
the static attribute visibility.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Message-ID: <bd909a2c-23ee-437d-9bd4-858119f6f266@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Use new member visible of struct hwmon_ops to simplify specifying
the static attribute visibility.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Message-ID: <5c26d8cf-d6dc-46c5-be7c-fd8207b3f177@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Use new member visible of struct hwmon_ops to simplify specifying
the static attribute visibility.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Message-ID: <d5d2570c-dfd9-4be5-ad9f-e721be477131@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Use new member visible of struct hwmon_ops to simplify specifying
the static attribute visibility.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Message-ID: <2b1f2778-1127-4979-b02d-f75e16497ad7@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Remove platform data & initialize with defaults
configuration & overwrite based on DT properties.
Signed-off-by: Naresh Solanki <naresh.solanki@9elements.com>
Message-ID: <20241007090426.811736-1-naresh.solanki@9elements.com>
[groeck: Dropped some unnecessary empty lines]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Several drivers return the same static value in their is_visible
callback, what results in code duplication. Therefore add an option
for drivers to specify a static visibility directly.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Message-ID: <89690b81-2c73-47ae-9ae9-45c77b45ca0c@gmail.com>
groeck: Renamed hwmon_ops_is_visible -> hwmon_is_visible
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Below mentioned spelling errors reported by codesepll
were fixed:
respresents ==> represents
signifcant ==> significant
bandwitdh ==> bandwidth
Signed-off-by: Everest K.C. <everestkc@everestkc.com.np>
Message-ID: <20241001011521.80982-1-everestkc@everestkc.com.np>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Theobroma Systems Mule is an MCU that emulates a set of I2C devices,
among which is an amc6821 and other devices that are reachable through
an I2C-mux.
The devices on the mux can be selected by writing the appropriate device
number to an I2C config register (amc6821: reg 0xff)
Implement "tsd,mule" compatible to instantiate the I2C-mux platform device
when probing the amc6821.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Farouk Bouabid <farouk.bouabid@cherry.de>
Message-ID: <20240906-dev-mule-i2c-mux-v8-4-dbd28a150e41@cherry.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Add dt-bindings for amc6821 intelligent temperature monitor and
pulse-width modulation (PWM) fan controller.
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Farouk Bouabid <farouk.bouabid@cherry.de>
Message-ID: <20240906-dev-mule-i2c-mux-v8-3-dbd28a150e41@cherry.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
To ensure code clarity and prevent potential errors, use ';' instead of
',' as a statement separator in the function mpq8785_identify.
Signed-off-by: Shen Lichuan <shenlichuan@vivo.com>
Message-ID: <20240919064939.3282-1-shenlichuan@vivo.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
INA260 is similar to other chips of the series, except it has an internal
shunt resistor. The calibration register is therefore not present. Also,
the current register address was changed, though that does not matter for
the driver since the shunt voltage register (which is now the current
register) value is already used to read the current.
Cc: Loic Guegan <loic.guegan@mailbox.org>
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Add configuration flag indicating if the chip supports alerts and limits
to prepare for adding INA260 support.
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
These drivers don't use the driver_data member of struct i2c_device_id,
so don't explicitly initialize this member.
This prepares putting driver_data in an anonymous union which requires
either no initialization or named designators. But it's also a nice
cleanup on its own.
While touching these structs, also remove commas after the sentinel
entries and use a consistent indention style.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Message-ID: <20240918123150.1540161-7-u.kleine-koenig@baylibre.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fixes from Stephen Boyd:
"A handful of Qualcomm clk driver fixes:
- Correct flags for X Elite USB MP GDSC and pcie pipediv2 clocks
- Fix alpha PLL post_div mask for the cases where width is not
specified
- Avoid hangs in the SM8350 video driver (venus) by setting HW_CTRL
trigger feature on the video clocks"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: qcom: gcc-x1e80100: Fix USB MP SS1 PHY GDSC pwrsts flags
clk: qcom: gcc-x1e80100: Fix halt_check for pipediv2 clocks
clk: qcom: clk-alpha-pll: Fix pll post div mask when width is not set
clk: qcom: videocc-sm8350: use HW_CTRL_TRIGGER for vcodec GDSCs
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"i2c-host fixes for v6.12-rc7 (from Andi):
- Fix designware incorrect behavior when concluding a transmission
- Fix Mule multiplexer error value evaluation"
* tag 'i2c-for-6.12-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: designware: do not hold SCL low when I2C_DYNAMIC_TAR_UPDATE is not set
i2c: muxes: Fix return value check in mule_i2c_mux_probe()
|
|
If the caller supplies an iocb->ki_pos value that is close to the
filesystem upper limit, and an iterator with a count that causes us to
overflow that limit, then filemap_read() enters an infinite loop.
This behaviour was discovered when testing xfstests generic/525 with the
"localio" optimisation for loopback NFS mounts.
Reported-by: Mike Snitzer <snitzer@kernel.org>
Fixes: c2a9737f45e2 ("vfs,mm: fix a dead loop in truncate_inode_pages_range()")
Tested-by: Mike Snitzer <snitzer@kernel.org>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fix from Borislav Petkov:
- Make sure GICv3 controller interrupt activation doesn't race with a
concurrent deactivation due to propagation delays of the register
write
* tag 'irq_urgent_for_v6.12_rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/gic-v3: Force propagation of the active state with a read-back
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull misc fixes from Andrew Morton:
"20 hotfixes, 14 of which are cc:stable.
Three affect DAMON. Lorenzo's five-patch series to address the
mmap_region error handling is here also.
Apart from that, various singletons"
* tag 'mm-hotfixes-stable-2024-11-09-22-40' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm:
mailmap: add entry for Thorsten Blum
ocfs2: remove entry once instead of null-ptr-dereference in ocfs2_xa_remove()
signal: restore the override_rlimit logic
fs/proc: fix compile warning about variable 'vmcore_mmap_ops'
ucounts: fix counter leak in inc_rlimit_get_ucounts()
selftests: hugetlb_dio: check for initial conditions to skip in the start
mm: fix docs for the kernel parameter ``thp_anon=``
mm/damon/core: avoid overflow in damon_feed_loop_next_input()
mm/damon/core: handle zero schemes apply interval
mm/damon/core: handle zero {aggregation,ops_update} intervals
mm/mlock: set the correct prev on failure
objpool: fix to make percpu slot allocation more robust
mm/page_alloc: keep track of free highatomic
mm: resolve faulty mmap_region() error path behaviour
mm: refactor arch_calc_vm_flag_bits() and arm64 MTE handling
mm: refactor map_deny_write_exec()
mm: unconditionally close VMAs on error
mm: avoid unsafe VMA hook invocation when error arises on mmap hook
mm/thp: fix deferred split unqueue naming and locking
mm/thp: fix deferred split queue not partially_mapped
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/Thunderbolt fixes from Greg KH:
"Here are some small remaining USB and Thunderbolt fixes and device ids
for 6.12-rc7. Included in here are:
- new USB serial driver device ids
- thunderbolt driver fixes for reported problems
- typec bugfixes
- dwc3 driver fix
- musb driver fix
All of these have been in linux-next this past week with no reported
issues"
* tag 'usb-6.12-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: serial: qcserial: add support for Sierra Wireless EM86xx
thunderbolt: Fix connection issue with Pluggable UD-4VPD dock
usb: typec: fix potential out of bounds in ucsi_ccg_update_set_new_cam_cmd()
usb: dwc3: fix fault at system suspend if device was already runtime suspended
usb: typec: qcom-pmic: init value of hdr_len/txbuf_len earlier
usb: musb: sunxi: Fix accessing an released usb phy
USB: serial: io_edgeport: fix use after free in debug printk
USB: serial: option: add Quectel RG650V
USB: serial: option: add Fibocom FG132 0x0112 composition
thunderbolt: Add only on-board retimers when !CONFIG_USB4_DEBUGFS_MARGINING
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver fixes from Greg KH:
"Here are two small memory leak fixes for the vchiq_arm staging driver
that have been sitting in my tree for weeks and should get merged for
6.12-rc7 so that people don't keep tripping over them.
They both have been in linux-next for a while with no reported
problems"
* tag 'staging-6.12-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: vchiq_arm: Use devm_kzalloc() for drv_mgmt allocation
staging: vchiq_arm: Use devm_kzalloc() for vchiq_arm_state allocation
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/andi.shyti/linux into i2c/for-current
i2c-host fixes for v6.12-rc7
In designware an incorrect behavior has been fixes when
concluding a transmission.
Fixed return error value evaluation in the Mule multiplexer.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/cel/linux
Pull nfsd fix from Chuck Lever:
- Fix a v6.12-rc regression when exporting ext4 filesystems with NFSD
* tag 'nfsd-6.12-4' of git://git.kernel.org/pub/scm/linux/kernel/git/cel/linux:
NFSD: Fix READDIR on NFSv3 mounts of ext4 exports
|
|
Pull smb client fix from Steve French:
"Fix net namespace refcount use after free issue"
* tag 'v6.12-rc6-smb3-client-fix' of git://git.samba.org/sfrench/cifs-2.6:
smb: client: Fix use-after-free of network namespace.
|
|
Pull block fix from Jens Axboe:
"Single fix for an issue triggered with PROVE_RCU=y, with nvme using
the wrong iterators for an SRCU protected list"
* tag 'block-6.12-20241108' of git://git.kernel.dk/linux:
nvme/host: Fix RCU list traversal to use SRCU primitive
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull thermal control fixes from Rafael Wysocki:
"These fix one issue in the qcom lmh thermal driver, a DT handling
issue in the thermal core and two issues in the userspace thermal
library:
- Allow tripless thermal zones defined in a DT to be registered in
accordance with the thermal DT bindings (Icenowy Zheng)
- Annotate LMH IRQs with lockdep classes to prevent lockdep from
reporting a possible recursive locking issue that cannot really
occur (Dmitry Baryshkov)
- Improve the thermal library "make clean" to remove a leftover
symbolic link created during compilation and fix the sampling
handler invocation in that library to pass the correct pointer to
it (Emil Dahl Juhl, zhang jiao)"
* tag 'thermal-6.12-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
thermal/of: support thermal zones w/o trips subnode
tools/lib/thermal: Remove the thermal.h soft link when doing make clean
tools/lib/thermal: Fix sampling handler context ptr
thermal/drivers/qcom/lmh: Remove false lockdep backtrace
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fix from Rafael Wysocki:
"Fix the asymmetric CPU capacity support code in the intel_pstate
driver, added during this develompent cycle, to address a corner case
in which the capacity of a CPU going online is not updated (Rafael
Wysocki)"
* tag 'pm-6.12-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq: intel_pstate: Update asym capacity for CPUs that were offline initially
cpufreq: intel_pstate: Clear hybrid_max_perf_cpu before driver registration
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fix from Rafael Wysocki:
"Fix the ACPI processor driver initialization ordering after recent
changes to avoid calling init_freq_invariance_cppc() too early on AMD
platforms (Mario Limonciello)"
* tag 'acpi-6.12-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: processor: Move arch_init_invariance_cppc() call later
|
|
Pull smb server fixes from Steve French:
"Four fixes, all also marked for stable:
- fix two potential use after free issues
- fix OOM issue with many simultaneous requests
- fix missing error check in RPC pipe handling"
* tag 'v6.12-rc6-ksmbd-fixes' of git://git.samba.org/ksmbd:
ksmbd: check outstanding simultaneous SMB operations
ksmbd: fix slab-use-after-free in smb3_preauth_hash_rsp
ksmbd: fix slab-use-after-free in ksmbd_smb2_session_create
ksmbd: Fix the missing xa_store error check
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Two small fixes, the drivers one in ufs simply delays running a work
queue and the generic one in zoned storage switches to a more correct
API that tries the standard buddy allocator first (for small
allocations); this fixes an allocation problem with small allocations
seen under memory pressure"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: ufs: core: Start the RTC update work later
scsi: sd_zbc: Use kvzalloc() to allocate REPORT ZONES buffer
|
