| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Drop the doubled word "be" in a comment.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
There are few issues on Zynq SOC observed in the stress tests causing
timeout errors. Even though all the data is received, timeout error
is thrown. This is due to an IP bug in which the COMP bit in ISR is
not set at end of transfer and completion interrupt is not generated.
This bug is seen on Zynq platforms when the following condition occurs:
Master read & HOLD bit set & Transfer size register reaches '0'.
One workaround is to clear the HOLD bit before the transfer size
register reaches '0'. The current implementation checks for this at
the start of the loop and also only for less than FIFO DEPTH case
(ignoring the equal to case).
So clear the HOLD bit when the data yet to receive is less than or
equal to the FIFO DEPTH. This avoids the IP bug condition.
Signed-off-by: Raviteja Narayanam <raviteja.narayanam@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
This reverts commit d358def706880defa4c9e87381c5bf086a97d5f9.
There are two issues with "i2c: cadence: Fix the hold bit setting" commit.
1. In case of combined message request from user space, when the HOLD
bit is cleared in cdns_i2c_mrecv function, a STOP condition is sent
on the bus even before the last message is started. This is because when
the HOLD bit is cleared, the FIFOS are empty and there is no pending
transfer. The STOP condition should occur only after the last message
is completed.
2. The code added by the commit is redundant. Driver is handling the
setting/clearing of HOLD bit in right way before the commit.
The setting of HOLD bit based on 'bus_hold_flag' is taken care in
cdns_i2c_master_xfer function even before cdns_i2c_msend/cdns_i2c_recv
functions.
The clearing of HOLD bit is taken care at the end of cdns_i2c_msend and
cdns_i2c_recv functions based on bus_hold_flag and byte count.
Since clearing of HOLD bit is done after the slave address is written to
the register (writing to address register triggers the message transfer),
it is ensured that STOP condition occurs at the right time after
completion of the pending transfer (last message).
Signed-off-by: Raviteja Narayanam <raviteja.narayanam@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
There is apparently one site that violates the rule that only current
and ttwu() will modify task->state, namely ptrace_{,un}freeze_traced()
will change task->state for a remote task.
Oleg explains:
"TASK_TRACED/TASK_STOPPED was always protected by siglock. In
particular, ttwu(__TASK_TRACED) must be always called with siglock
held. That is why ptrace_freeze_traced() assumes it can safely do
s/TASK_TRACED/__TASK_TRACED/ under spin_lock(siglock)."
This breaks the ordering scheme introduced by commit:
dbfb089d360b ("sched: Fix loadavg accounting race")
Specifically, the reload not matching no longer implies we don't have
to block.
Simply things by noting that what we need is a LOAD->STORE ordering
and this can be provided by a control dependency.
So replace:
prev_state = prev->state;
raw_spin_lock(&rq->lock);
smp_mb__after_spinlock(); /* SMP-MB */
if (... && prev_state && prev_state == prev->state)
deactivate_task();
with:
prev_state = prev->state;
if (... && prev_state) /* CTRL-DEP */
deactivate_task();
Since that already implies the 'prev->state' load must be complete
before allowing the 'prev->on_rq = 0' store to become visible.
Fixes: dbfb089d360b ("sched: Fix loadavg accounting race")
Reported-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Oleg Nesterov <oleg@redhat.com>
Tested-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Tested-by: Christian Brauner <christian.brauner@ubuntu.com>
|
|
On x86-32 the idt_table with 256 entries needs only 2048 bytes. It is
page-aligned, but the end of the .bss..page_aligned section is not
guaranteed to be page-aligned.
As a result, objects from other .bss sections may end up on the same 4k
page as the idt_table, and will accidentially get mapped read-only during
boot, causing unexpected page-faults when the kernel writes to them.
This could be worked around by making the objects in the page aligned
sections page sized, but that's wrong.
Explicit sections which store only page aligned objects have an implicit
guarantee that the object is alone in the page in which it is placed. That
works for all objects except the last one. That's inconsistent.
Enforcing page sized objects for these sections would wreckage memory
sanitizers, because the object becomes artificially larger than it should
be and out of bound access becomes legit.
Align the end of the .bss..page_aligned and .data..page_aligned section on
page-size so all objects places in these sections are guaranteed to have
their own page.
[ tglx: Amended changelog ]
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Kees Cook <keescook@chromium.org>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20200721093448.10417-1-joro@8bytes.org
|
|
Shannon Nelson says:
====================
ionic updates
These are a few odd code tweaks to the ionic driver: FW defined MTU
limits, remove unnecessary code, and other tidiness tweaks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add some new interface values and update a few more descriptions.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We can prevent potential incorrect DMA access attempts from the
NIC by enabling bus-master after the reset, and by disabling
bus-master earlier in cleanup.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix up our comparison to better handle a potential (but largely
unlikely) wrap around.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Clean up some unused code.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If the host system's udev fails to set a new name for the
network port, there is no NETDEV_CHANGENAME event to trigger
the driver to send the name down to the firmware. It is safe
to set the lif name multiple times, so we add a call early on
to set the default netdev name to be sure the FW has something
to use in its internal debug logging. Then when udev gets
around to changing it we can update it to the actual name the
system will be using.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Change from using hardcoded MTU limits and instead use the
firmware defined limits. The value from the LIF attributes is
the frame size, so we take off the header size to convert to
MTU size.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently drive supports taprio offload which is a tc feature offloaded
to cpsw hardware. So driver has to set the hw feature flag, NETIF_F_HW_TC
in the net device to be compliant. This patch adds the flag.
Fixes: 8127224c2708 ("ethernet: ti: am65-cpsw-qos: add TAPRIO offload support")
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When regmap_update_bits failed in ave_init(), calls of the functions
reset_control_assert() and clk_disable_unprepare() were missed.
Add goto out_reset_assert to do this.
Fixes: 57878f2f4697 ("net: ethernet: ave: add support for phy-mode setting of system controller")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Reviewed-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The commit fe80536acf83 ("bareudp: Added attribute to enable & disable
rx metadata collection") breaks the the original(5.7) default behavior of
bareudp module to collect RX metadadata at the receive. It was added to
avoid the crash at the kernel neighbour subsytem when packet with metadata
from bareudp is processed. But it is no more needed as the
commit 394de110a733 ("net: Added pointer check for
dst->ops->neigh_lookup in dst_neigh_lookup_skb") solves this crash.
Fixes: fe80536acf83 ("bareudp: Added attribute to enable & disable rx metadata collection")
Signed-off-by: Martin Varghese <martin.varghese@nokia.com>
Acked-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This driver is not working because of problems of its receiving code.
This patch fixes it to make it work.
When the driver receives an LAPB frame, it should first pass the frame
to the LAPB module to process. After processing, the LAPB module passes
the data (the packet) back to the driver, the driver should then add a
one-byte pseudo header and pass the data to upper layers.
The changes to the "x25_asy_bump" function and the
"x25_asy_data_indication" function are to correctly implement this
procedure.
Also, the "x25_asy_unesc" function ignores any frame that is shorter
than 3 bytes. However the shortest frames are 2-byte long. So we need
to change it to allow 2-byte frames to pass.
Cc: Eric Dumazet <edumazet@google.com>
Cc: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Reviewed-by: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Ioana Ciornei says:
====================
dpaa2-eth: add support for TBF offload
This patch set adds support for TBF offload in dpaa2-eth.
The first patch restructures how the .ndo_setup_tc() callback is
implemented (each Qdisc is treated in a separate function), the second
patch just adds the necessary APIs for configuring the Tx shaper and the
last one is handling TC_SETUP_QDISC_TBF and configures as requested the
shaper.
====================
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
React to TC_SETUP_QDISC_TBF and configure the egress shaper as
appropriate with the maximum rate and burst size requested by the user.
TBF can only be offloaded on DPAA2 when it's the root qdisc, ie it's a
per port shaper.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add the necessary API (dpni_set_tx_shaping) for configuring the rate and
burst size of a per port shaper in DPAA2.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move the setup done for MQPRIO into a separate function so that
with the addition of another offload we do not crowd
dpaa2_eth_setup_tc(). After this restructuring it's easier to see what
is supported in terms of Qdisc offloading.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Only used in token.c.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The sync_thread_backup only checks sk_receive_queue is empty or not,
there is a situation which cannot sync the connection entries when
sk_receive_queue is empty and sk_rmem_alloc is larger than sk_rcvbuf,
the sync packets are dropped in __udp_enqueue_schedule_skb, this is
because the packets in reader_queue is not read, so the rmem is
not reclaimed.
Here I add the check of whether the reader_queue of the udp sock is
empty or not to solve this problem.
Fixes: 2276f58ac589 ("udp: use a separate rx queue for packet reception")
Reported-by: zhouxudong <zhouxudong8@huawei.com>
Signed-off-by: guodeqing <geffrey.guo@huawei.com>
Acked-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Parav Pandit says:
====================
devlink small improvements
This short series improves the devlink code for lock commment,
simplifying checks and keeping the scope of mutex lock for necessary
fields.
Patch summary:
Patch-1 Keep the devlink_mutex for only for necessary changes.
Patch-2 Avoids duplicate check for reload flag
Patch-3 Adds missing comment for the scope of devlink instance lock
Patch-4 Constify devlink instance pointer
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Constify devlink instance pointer while checking if reload operation is
supported or not.
This helps to review the scope of checks done in reload.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add comment to describe the purpose of devlink instance lock.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Reload operation is enabled or not is already checked by
devlink_reload(). Hence, remove the duplicate check from
devlink_nl_cmd_reload().
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is no need to hold a device global lock when initializing
devlink device fields of a devlink instance which is not yet part of the
devices list.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For most chip versions this has been added already. Allow also for
RTL8125A to enable ASPM.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
According to 'man 8 ip-netns', if `ip netns identify` returns an empty string,
there's no net namespace associated with current PID: fix the net ns entrance
logic.
Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit d341659f470b ("xtensa: switch to providing
csum_and_copy_from_user()") introduced access check, but incorrectly
tested dst instead of src.
Fix access_ok argument in csum_and_copy_from_user.
Cc: Al Viro <viro@zeniv.linux.org.uk>
Fixes: d341659f470b ("xtensa: switch to providing csum_and_copy_from_user()")
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Alexander Lobakin says:
====================
qed: suppress irrelevant error messages on HW init
This raises the verbosity level of several error/warning messages on
driver/module initialization, most of which are false-positives, and
the one actively spamming the log for no reason.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It was found that qed_pglueb_rbc_attn_handler() can produce a lot of
false-positive error detections on driver load/reload (especially after
crashes/recoveries) and spam the kernel log:
[ 4.958275] [qed_pglueb_rbc_attn_handler:324()]ICPL error - 00d00ff0
[ 2079.146764] [qed_pglueb_rbc_attn_handler:324()]ICPL error - 00d80ff0
[ 2116.374631] [qed_pglueb_rbc_attn_handler:324()]ICPL error - 00d80ff0
[ 2135.250564] [qed_pglueb_rbc_attn_handler:324()]ICPL error - 00d80ff0
[...]
Reduce the logging level of two false-positive prone error messages from
notice to verbose on initialization (only) to not mix it with real error
attentions while debugging.
Fixes: 666db4862f2d ("qed: Revise load sequence to avoid PCI errors")
Signed-off-by: Alexander Lobakin <alobakin@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Change the verbosity of the "don't support RoCE & iWARP simultaneously"
warning to debug level to stop flooding on driver/hardware initialization:
[ 4.783230] qede 01:00.00: Storm FW 8.37.7.0, Management FW 8.52.9.0
[MBI 15.10.6] [eth0]
[ 4.810020] [qed_rdma_set_pf_params:2076()]Current day drivers don't
support RoCE & iWARP simultaneously on the same PF. Default to RoCE-only
[ 4.861186] qede 01:00.01: Storm FW 8.37.7.0, Management FW 8.52.9.0
[MBI 15.10.6] [eth1]
[ 4.893311] [qed_rdma_set_pf_params:2076()]Current day drivers don't
support RoCE & iWARP simultaneously on the same PF. Default to RoCE-only
[ 5.181713] qede a1:00.00: Storm FW 8.37.7.0, Management FW 8.52.9.0
[MBI 15.10.6] [eth2]
[ 5.224740] [qed_rdma_set_pf_params:2076()]Current day drivers don't
support RoCE & iWARP simultaneously on the same PF. Default to RoCE-only
[ 5.276449] qede a1:00.01: Storm FW 8.37.7.0, Management FW 8.52.9.0
[MBI 15.10.6] [eth3]
[ 5.318671] [qed_rdma_set_pf_params:2076()]Current day drivers don't
support RoCE & iWARP simultaneously on the same PF. Default to RoCE-only
[ 5.369548] qede a1:00.02: Storm FW 8.37.7.0, Management FW 8.52.9.0
[MBI 15.10.6] [eth4]
[ 5.411645] [qed_rdma_set_pf_params:2076()]Current day drivers don't
support RoCE & iWARP simultaneously on the same PF. Default to RoCE-only
Fixes: e0a8f9de16fc ("qed: Add iWARP enablement support")
Signed-off-by: Alexander Lobakin <alobakin@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the nsim_create(), rtnl_lock() is called before nsim_bpf_init().
If nsim_bpf_init() is failed, rtnl_unlock() should be called,
but it isn't called.
So, unbalanced locking would occur.
Fixes: e05b2d141fef ("netdevsim: move netdev creation/destruction to dev probe")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Arthur Kiyanovski says:
====================
ENA driver new features
V4 changes:
-----------
Add smp_rmb() to "net: ena: avoid unnecessary rearming of interrupt
vector when busy-polling" to adhere to the linux kernel memory model,
and update the commit message accordingly.
V3 changes:
-----------
1. Add "net: ena: enable support of rss hash key and function
changes" patch again, with more explanations why it should
be in net-next in commit message.
2. Add synchronization considerations to "net: ena: avoid unnecessary
rearming of interrupt vector when busy-polling"
V2 changes:
-----------
1. Update commit messages of 2 patches to be more verbose.
2. Remove "net: ena: enable support of rss hash key and function
changes" patch. Will be resubmitted net.
V1 cover letter:
----------------
This patchset contains performance improvements, support for new devices
and functionality:
1. Support for upcoming ENA devices
2. Avoid unnecessary IRQ unmasking in busy poll to reduce interrupt rate
3. Enabling device support for RSS function and key manipulation
4. Support for NIC-based traffic mirroring (SPAN port)
5. Additional PCI device ID
6. Cosmetic changes
====================
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
New devices add a new hardware acceleration engine, which adds some
restrictions to the driver.
Metadata descriptor must be present for each packet and the maximum
burst size between two doorbells is now limited to a number
advertised by the device.
This patch adds:
1. A handshake protocol between the driver and the device, so the
device will enable the accelerated queues only when both sides
support it.
2. The driver support for the new acceleration engine:
2.1. Send metadata descriptor for each Tx packet.
2.2. Limit the number of packets sent between doorbells.(*)
(*) A previous driver implementation of this feature was comitted in
commit 05d62ca218f8 ("net: ena: add handling of llq max tx burst size")
however the design of the interface between the driver and device
changed since then. This change is reflected in this commit.
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the ENA device resets to recover from some error state, all LLQ
configuration values are reset to their defaults, because LLQ is
initialized only once during ena_probe().
Changes in this commit:
1. Move the LLQ configuration process into ena_init_device()
which is called from both ena_probe() and ena_restore_device(). This
way, LLQ setup configurations that are different from the default
values will survive resets.
2. Extract the LLQ bar mapping to ena_map_llq_bar(),
and call once in the lifetime of the driver from ena_probe(),
since there is no need to unmap and map the LLQ bar again every reset.
3. Map the LLQ bar if it exists, regardless if initialization of LLQ
placement policy (ENA_ADMIN_PLACEMENT_POLICY_DEV) succeeded
or not. Initialization might fail the first time, falling back to the
ENA_ADMIN_PLACEMENT_POLICY_HOST placement policy, but later succeed
after device reset, in which case the LLQ bar needs to be mapped
already.
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add the rss_configurable_function_key bit to driver_supported_feature.
This bit tells the device that the driver in question supports the
retrieving and updating of RSS function and hash key, and therefore
the device should allow RSS function and key manipulation.
This commit turns on device support for hash key and RSS function
management. Without this commit this feature is turned off at the
device and appears to the user as unsupported.
This commit concludes the following series of already merged commits:
commit 0af3c4e2eab8 ("net: ena: changes to RSS hash key allocation")
commit c1bd17e51c71 ("net: ena: change default RSS hash function to Toeplitz")
commit f66c2ea3b18a ("net: ena: allow setting the hash function without changing the key")
commit e9a1de378dd4 ("net: ena: fix error returning in ena_com_get_hash_function()")
commit 80f8443fcdaa ("net: ena: avoid unnecessary admin command when RSS function set fails")
commit 6a4f7dc82d1e ("net: ena: rss: do not allocate key when not supported")
commit 0d1c3de7b8c7 ("net: ena: fix incorrect default RSS key")
The above commits represent the last part of the implementation of
this feature, and with them merged the feature can be enabled
in the device.
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for traffic mirroring, where the hardware reads the
buffer from the instance memory directly.
Traffic Mirroring needs access to the rx buffers in the instance.
To have this access, this patch:
1. Changes the code to map and unmap the rx buffers bidirectionally.
2. Enables the relevant bit in driver_supported_features to indicate
to the FW that this driver supports traffic mirroring.
Rx completion is not generated until mirroring is done to avoid
the situation where the driver changes the buffer before it is
mirrored.
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The size of the admin statistics in ena_com_stats_admin is changed
from 32bit to 64bit so to align with the sizes of the other statistics
in the driver (i.e. rx_stats, tx_stats and ena_stats_dev).
This is done as part of an effort to create a unified API to read
statistics.
Signed-off-by: Shay Agroskin <shayagr@amazon.com>
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
gcc 4.8 reports a warning when initializing with = {0}.
Dropping the "0" from the braces fixes the issue.
This fix is not ANSI compatible but is allowed by gcc.
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a reserved PCI device ID to the driver's table
Used for internal testing purposes.
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For an overview of the race created by this patch goto synchronization
label.
In napi busy-poll mode, the kernel invokes the napi handler of the
device repeatedly to poll the NIC's receive queues. This process
repeats until a timeout, specific for each connection, is up.
By polling packets in busy-poll mode the user may gain lower latency
and higher throughput (since the kernel no longer waits for interrupts
to poll the queues) in expense of CPU usage.
Upon completing a napi routine, the driver checks whether
the routine was called by an interrupt handler. If so, the driver
re-enables interrupts for the device. This is needed since an
interrupt routine invocation disables future invocations until
explicitly re-enabled.
The driver avoids re-enabling the interrupts if they were not disabled
in the first place (e.g. if driver in busy mode).
Originally, the driver checked whether interrupt re-enabling is needed
by reading the 'ena_napi->unmask_interrupt' variable. This atomic
variable was set upon interrupt and cleared after re-enabling it.
In the 4.10 Linux version, the 'napi_complete_done' call was changed
so that it returns 'false' when device should not re-enable
interrupts, and 'true' otherwise. The change includes reading the
"NAPIF_STATE_IN_BUSY_POLL" flag to check if the napi call is in
busy-poll mode, and if so, return 'false'.
The driver was changed to re-enable interrupts according to this
routine's return value.
The Linux community rejected the use of the
'ena_napi->unmaunmask_interrupt' variable to determine whether
unmasking is needed, and urged to use napi_napi_complete_done()
return value solely.
See https://lore.kernel.org/patchwork/patch/741149/ for more details
As explained, a busy-poll session exists for a specified timeout
value, after which it exits the busy-poll mode and re-enters it later.
This leads to many invocations of the napi handler where
napi_complete_done() false indicates that interrupts should be
re-enabled.
This creates a bug in which the interrupts are re-enabled
unnecessarily.
To reproduce this bug:
1) echo 50 | sudo tee /proc/sys/net/core/busy_poll
2) echo 50 | sudo tee /proc/sys/net/core/busy_read
3) Add counters that check whether
'ena_unmask_interrupt(tx_ring, rx_ring);'
is called without disabling the interrupts in the first
place (i.e. with calling the interrupt routine
ena_intr_msix_io())
Steps 1+2 enable busy-poll as the default mode for new connections.
The busy poll routine rearms the interrupts after every session by
design, and so we need to add an extra check that the interrupts were
masked in the first place.
synchronization:
This patch introduces a race between the interrupt handler
ena_intr_msix_io() and the napi routine ena_io_poll().
Some macros and instruction were added to prevent this race from leaving
the interrupts masked. The following specifies the different race
scenarios in this patch:
1) interrupt handler and napi routine run sequentially
i) interrupt handler is called, sets 'interrupts_masked' flag and
successfully schedules the napi handler via softirq.
In this scenario the napi routine might not see the flag change
for several reasons:
a) The flag is stored in a register by the compiler. For this
case the WRITE_ONCE macro which prevents this.
b) The compiler might reorder the instruction. For this the
smp_wmb() instruction was used which implies a compiler memory
barrier.
c) On archs with weak consistency model (like ARM64) the napi
routine might be scheduled and start running before the flag
STORE instruction is committed to cache/memory. To ensure this
doesn't happen, the smp_wmb() instruction was added. It ensures
that the flag set instruction is committed before scheduling
napi.
ii) compiler reorders the flag's value check in the 'if' with
the flag set in the napi routine.
This scenario is prevented by smp_rmb() call after the flag check.
2) interrupt handler and napi routine run in parallel (can happen when
busy poll routine invokes the napi handler)
i) interrupt handler sets the flag in one core, while the napi
routine reads it in another core.
This scenario also is divided into two cases:
a) napi_complete_done() doesn't finish running, in which case
napi_sched() would just set NAPIF_STATE_MISSED and the napi
routine would reschedule itself without changing the flag's value.
b) napi_complete_done() finishes running. In this case the
napi routine might override the flag's value.
This doesn't present any rise since it later unmasks the
interrupt vector.
Signed-off-by: Shay Agroskin <shayagr@amazon.com>
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
- Free ILT lines used for XRC-SRQ's contexts.
- Free XRCD bitmap
Fixes: b8204ad878ce7 ("qed: changes to ILT to support XRC")
Fixes: 7bfb399eca460 ("qed: Add XRC to RoCE")
Signed-off-by: Michal Kalderon <mkalderon@marvell.com>
Signed-off-by: Yuval Basson <ybason@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When doing "ip link set dev ... up" for a ksz9477 backed link,
ksz9477_phy_setup is called and it calls phy_remove_link_mode to remove
1000baseT HDX. During phy_remove_link_mode, phy_advertise_supported is
called. Doing so reverts any previous change to advertised link modes
e.g. using a udevd .link file.
phy_remove_link_mode is not meant to be used while opening a link and
should be called during phy probe when the link is not yet available to
userspace.
Therefore move the phy_remove_link_mode calls into
ksz9477_switch_register. It indirectly calls dsa_register_switch, which
creates the relevant struct phy_devices and we update the link modes
right after that. At that time dev->features is already initialized by
ksz9477_switch_detect.
Remove phy_setup from ksz_dev_ops as no users remain.
Link: https://lore.kernel.org/netdev/20200715192722.GD1256692@lunn.ch/
Fixes: 42fc6a4c613019 ("net: dsa: microchip: prepare PHY for proper advertisement")
Signed-off-by: Helmut Grohne <helmut.grohne@intenta.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Huazhong Tan says:
====================
net: hns3: fixes for -net
There are some bugfixes for the HNS3 ethernet driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, PF queries the MAC link status per second by calling
function hclge_get_mac_link_status(). It return the error code
when failed to send cmdq command to firmware. It's incorrect,
because this return value is used as the MAC link status, which
0 means link down, and none-zero means link up. So fixes it.
Fixes: 46a3df9f9718 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The content of the TX desc is automatically cleared by the HW
when the HW has sent out the packet to the wire. When desc filling
fails in hns3_nic_net_xmit(), it will call hns3_clear_desc() to do
the error handling, which miss zeroing of the TX desc and the
checking if a unmapping is needed.
So add the zeroing and checking in hns3_clear_desc() to avoid the
above problem. Also add DESC_TYPE_UNKNOWN to indicate the info in
desc_cb is not valid, because hns3_nic_reclaim_desc() may treat
the desc_cb->type of zero as packet and add to the sent pkt
statistics accordingly.
Fixes: 76ad4f0ee747 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With GRO and fraglist support, the SKB can be aggregated to
a total size of 65535, and when that SKB is forwarded through
a bridge, the size of the SKB may be pushed to exceed the size
of 65535 when br_dev_queue_push_xmit() is called.
The max send size of BD supported by the HW is 65535, when a SKB
with a headlen of over 65535 is sent to the driver, the driver
needs to use multi BD to send the linear data, and the send size
of the last BD is calculated incorrectly by the driver who is
using '&' operation, which causes a TX error.
Use '%' operation to fix this problem.
Fixes: 3fe13ed95dd3 ("net: hns3: avoid mult + div op in critical data path")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When a big TX buffer is sent using multi BD, the driver maps the
whole TX buffer, and unmaps it using info in desc_cb corresponding
to each BD, but only the info in the desc_cb of first BD is correct,
other info in desc_cb is wrong, which causes TX unmapping problem
when SMMU is on.
Only set the mapping and freeing info in the desc_cb of first BD to
fix this problem, because the TX buffer only need to be unmapped and
freed once.
Fixes: 1e8a7977d09f("net: hns3: add handling for big TX fragment")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huzhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
