| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The opcode range for fault injection from user should be validated before
it is applied to the fault->opcodes[] bitmap to avoid out-of-bound
error.
Cc: <stable@vger.kernel.org>
Fixes: a74d5307caba ("IB/hfi1: Rework fault injection machinery")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Kaike Wan <kaike.wan@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
Jakub Kicinski says:
====================
tls: add support for kernel-driven resync and nfp RX offload
This series adds TLS RX offload for NFP and completes the offload
by providing resync strategies. When TLS data stream looses segments
or experiences reorder NIC can no longer perform in line offload.
Resyncs provide information about placement of records in the
stream so that offload can resume.
Existing TLS resync mechanisms are not a great fit for the NFP.
In particular the TX resync is hard to implement for packet-centric
NICs. This patchset adds an ability to perform TX resync in a way
similar to the way initial sync is done - by calling down to the
driver when new record is created after driver indicated sync had
been lost.
Similarly on the RX side, we try to wait for a gap in the stream
and send record information for the next record. This works very
well for RPC workloads which are the primary focus at this time.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When TCP stream gets out of sync (driver stops receiving skbs
with expected TCP sequence numbers) request a TX resync from
the kernel.
We try to distinguish retransmissions from missed transmissions
by comparing the sequence number to expected - if it's further
than the expected one - we probably missed packets.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
TLS offload drivers keep track of TCP seq numbers to make sure
the packets are fed into the HW in order.
When packets get dropped on the way through the stack, the driver
will get out of sync and have to use fallback encryption, but unless
TCP seq number is resynced it will never match the packets correctly
(or even worse - use incorrect record sequence number after TCP seq
wraps).
Existing drivers (mlx5) feed the entire record on every out-of-order
event, allowing FW/HW to always be in sync.
This patch adds an alternative, more akin to the RX resync. When
driver sees a frame which is past its expected sequence number the
stream must have gotten out of order (if the sequence number is
smaller than expected its likely a retransmission which doesn't
require resync). Driver will ask the stack to perform TX sync
before it submits the next full record, and fall back to software
crypto until stack has performed the sync.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently only RX direction is ever resynced, however, TX may
also get out of sequence if packets get dropped on the way to
the driver. Rename the resync callback and add a direction
parameter.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Set ethtool TLS RX feature based on NIC capabilities, and enable
TLS RX when connections are added for decryption.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Enable kernel-controlled RX resync and propagate TLS connection
RX resync from kernel TLS to firmware.
Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some control messages must be sent from atomic context. The mailbox
takes sleeping locks and uses a waitqueue so add a "posted" version
of communication.
Trylock the semaphore and if that's successful kick of the device
communication. The device communication will be completed from
a workqueue, which will also release the semaphore.
If locks are taken queue the message and return. Schedule a
different workqueue to take the semaphore and run the communication.
Note that the there are currently no atomic users which would actually
need the return value, so all replies to posted messages are just
freed.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We need the name nfp_ccm_mbox_alloc() for allocating the mailbox
communication channel itself.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Firmware indicates when a packet has been decrypted by reusing the
currently unused BPF flag. Transfer this information into the skb
and provide a statistic of all decrypted segments.
Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
TLS offload device may lose sync with the TCP stream if packets
arrive out of order. Drivers can currently request a resync at
a specific TCP sequence number. When a record is found starting
at that sequence number kernel will inform the device of the
corresponding record number.
This requires the device to constantly scan the stream for a
known pattern (constant bytes of the header) after sync is lost.
This patch adds an alternative approach which is entirely under
the control of the kernel. Kernel tracks records it had to fully
decrypt, even though TLS socket is in TLS_HW mode. If multiple
records did not have any decrypted parts - it's a pretty strong
indication that the device is out of sync.
We choose the min number of fully encrypted records to be 2,
which should hopefully be more than will get retransmitted at
a time.
After kernel decides the device is out of sync it schedules a
resync request. If the TCP socket is empty the resync gets
performed immediately. If socket is not empty we leave the
record parser to resync when next record comes.
Before resync in message parser we peek at the TCP socket and
don't attempt the sync if the socket already has some of the
next record queued.
On resync failure (encrypted data continues to flow in) we
retry with exponential backoff, up to once every 128 records
(with a 16k record thats at most once every 2M of data).
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
handle_device_resync() doesn't describe the function very well.
The function checks if resync should be issued upon parsing of
a new record.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
TLS offload code casts record number to a u64. The buffer
should be aligned to 8 bytes, but its actually a __be64, and
the rest of the TLS code treats it as big int. Make the
offload callbacks take a byte array, drivers can make the
choice to do the ugly cast if they want to.
Prepare for copying the record number onto the stack by
defining a constant for max size of the byte array.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We subtract "TLS_HEADER_SIZE - 1" from req_seq, then if they
match we add the same constant to seq. Just add it to seq,
and we don't have to touch req_seq.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The variable 'status' in __packet_lookup_frame_in_block() is never used since
introduction in commit f6fb8f100b80 ("af-packet: TPACKET_V3 flexible buffer
implementation."), we can remove it.
Signed-off-by: Mao Wenan <maowenan@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Stefano Brivio says:
====================
Don't assume linear buffers in error handlers for VXLAN and GENEVE
Guillaume noticed the same issue fixed by commit 26fc181e6cac ("fou, fou6:
do not assume linear skbs") for fou and fou6 is also present in VXLAN and
GENEVE error handlers: we can't assume linear buffers there, we need to
use pskb_may_pull() instead.
====================
Acked-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In commit a07966447f39 ("geneve: ICMP error lookup handler") I wrongly
assumed buffers from icmp_socket_deliver() would be linear. This is not
the case: icmp_socket_deliver() only guarantees we have 8 bytes of linear
data.
Eric fixed this same issue for fou and fou6 in commits 26fc181e6cac
("fou, fou6: do not assume linear skbs") and 5355ed6388e2 ("fou, fou6:
avoid uninit-value in gue_err() and gue6_err()").
Use pskb_may_pull() instead of checking skb->len, and take into account
the fact we later access the GENEVE header with udp_hdr(), so we also
need to sum skb_transport_header() here.
Reported-by: Guillaume Nault <gnault@redhat.com>
Fixes: a07966447f39 ("geneve: ICMP error lookup handler")
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In commit c3a43b9fec8a ("vxlan: ICMP error lookup handler") I wrongly
assumed buffers from icmp_socket_deliver() would be linear. This is not
the case: icmp_socket_deliver() only guarantees we have 8 bytes of linear
data.
Eric fixed this same issue for fou and fou6 in commits 26fc181e6cac
("fou, fou6: do not assume linear skbs") and 5355ed6388e2 ("fou, fou6:
avoid uninit-value in gue_err() and gue6_err()").
Use pskb_may_pull() instead of checking skb->len, and take into account
the fact we later access the VXLAN header with udp_hdr(), so we also
need to sum skb_transport_header() here.
Reported-by: Guillaume Nault <gnault@redhat.com>
Fixes: c3a43b9fec8a ("vxlan: ICMP error lookup handler")
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ASSERT_OVSL() in ovs_vport_del() is unnecessary because
ovs_vport_del() is only called by ovs_dp_detach_port() and
ovs_dp_detach_port() calls ASSERT_OVSL() too.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Reviewed-by: Greg Rose <gvrose8192@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
netlink_walk_start() needed to return an error code because of
rhashtable_walk_init(). but that was converted to rhashtable_walk_enter()
and it is a void type function. so now netlink_walk_start() doesn't need
any return value.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In order to create an internal vport, internal_dev_create() is used and
that calls register_netdevice() internally.
If register_netdevice() fails, it calls dev->priv_destructor() to free
private data of netdev. actually, a private data of this is a vport.
Hence internal_dev_create() should not free and use a vport after failure
of register_netdevice().
Test command
ovs-dpctl add-dp bonding_masters
Splat looks like:
[ 1035.667767] kasan: GPF could be caused by NULL-ptr deref or user memory access
[ 1035.675958] general protection fault: 0000 [#1] SMP DEBUG_PAGEALLOC KASAN PTI
[ 1035.676916] CPU: 1 PID: 1028 Comm: ovs-vswitchd Tainted: G B 5.2.0-rc3+ #240
[ 1035.676916] RIP: 0010:internal_dev_create+0x2e5/0x4e0 [openvswitch]
[ 1035.676916] Code: 48 c1 ea 03 80 3c 02 00 0f 85 9f 01 00 00 4c 8b 23 48 b8 00 00 00 00 00 fc ff df 49 8d bc 24 60 05 00 00 48 89 fa 48 c1 ea 03 <80> 3c 02 00 0f 85 86 01 00 00 49 8b bc 24 60 05 00 00 e8 e4 68 f4
[ 1035.713720] RSP: 0018:ffff88810dcb7578 EFLAGS: 00010206
[ 1035.713720] RAX: dffffc0000000000 RBX: ffff88810d13fe08 RCX: ffffffff84297704
[ 1035.713720] RDX: 00000000000000ac RSI: 0000000000000000 RDI: 0000000000000560
[ 1035.713720] RBP: 00000000ffffffef R08: fffffbfff0d3b881 R09: fffffbfff0d3b881
[ 1035.713720] R10: 0000000000000001 R11: fffffbfff0d3b880 R12: 0000000000000000
[ 1035.768776] R13: 0000607ee460b900 R14: ffff88810dcb7690 R15: ffff88810dcb7698
[ 1035.777709] FS: 00007f02095fc980(0000) GS:ffff88811b400000(0000) knlGS:0000000000000000
[ 1035.777709] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 1035.777709] CR2: 00007ffdf01d2f28 CR3: 0000000108258000 CR4: 00000000001006e0
[ 1035.777709] Call Trace:
[ 1035.777709] ovs_vport_add+0x267/0x4f0 [openvswitch]
[ 1035.777709] new_vport+0x15/0x1e0 [openvswitch]
[ 1035.777709] ovs_vport_cmd_new+0x567/0xd10 [openvswitch]
[ 1035.777709] ? ovs_dp_cmd_dump+0x490/0x490 [openvswitch]
[ 1035.777709] ? __kmalloc+0x131/0x2e0
[ 1035.777709] ? genl_family_rcv_msg+0xa54/0x1030
[ 1035.777709] genl_family_rcv_msg+0x63a/0x1030
[ 1035.777709] ? genl_unregister_family+0x630/0x630
[ 1035.841681] ? debug_show_all_locks+0x2d0/0x2d0
[ ... ]
Fixes: cf124db566e6 ("net: Fix inconsistent teardown and release of private netdev state.")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Reviewed-by: Greg Rose <gvrose8192@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The below patch fixes an incorrect zerocopy refcnt increment when
appending with MSG_MORE to an existing zerocopy udp skb.
send(.., MSG_ZEROCOPY | MSG_MORE); // refcnt 1
send(.., MSG_ZEROCOPY | MSG_MORE); // refcnt still 1 (bar frags)
But it missed that zerocopy need not be passed at the first send. The
right test whether the uarg is newly allocated and thus has extra
refcnt 1 is not !skb, but !skb_zcopy.
send(.., MSG_MORE); // <no uarg>
send(.., MSG_ZEROCOPY); // refcnt 1
Fixes: 100f6d8e09905 ("net: correct zerocopy refcnt with udp MSG_MORE")
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This test checks that route exceptions can be successfully listed and
flushed using ip -6 route {list,flush} cache.
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
[What]
readptr read always returns zero, since most likely
these blocks are either power or clock gated.
[How]
fetch rptr after amdgpu_ring_alloc() which informs
the power management code that the block is about to be
used and hence the gating is turned off.
Signed-off-by: Louis Li <Ching-shih.Li@amd.com>
Signed-off-by: Shirish S <shirish.s@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
The ioctl argument was parsed as the wrong type.
Fixes: b21d9c435f93 ("ovl: support the FS_IOC_FS[SG]ETXATTR ioctls")
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
|
|
In RV32, udelay would delay the wrong cycle. When it shifts right
"UDELAY_SHIFT" bits, it either delays 0 cycle or 1 cycle. It only works
correctly in RV64. Because the 'ucycles' always needs to be 64 bits
variable.
Signed-off-by: Nick Hu <nickhu@andestech.com>
Reviewed-by: Palmer Dabbelt <palmer@sifive.com>
[paul.walmsley@sifive.com: fixed minor spelling error]
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
|
|
Booting up with DMA_API_DEBUG_SG=y generates a warning due to the driver
forgot to set dma_parms appropriately. Set it just after vmw_dma_masks()
in vmw_driver_load().
DMA-API: vmwgfx 0000:00:0f.0: mapping sg segment longer than device
claims to support [len=2097152] [max=65536]
WARNING: CPU: 2 PID: 261 at kernel/dma/debug.c:1232
debug_dma_map_sg+0x360/0x480
Hardware name: VMware, Inc. VMware Virtual Platform/440BX Desktop
Reference Platform, BIOS 6.00 04/13/2018
RIP: 0010:debug_dma_map_sg+0x360/0x480
Call Trace:
vmw_ttm_map_dma+0x3b1/0x5b0 [vmwgfx]
vmw_bo_map_dma+0x25/0x30 [vmwgfx]
vmw_otables_setup+0x2a8/0x750 [vmwgfx]
vmw_request_device_late+0x78/0xc0 [vmwgfx]
vmw_request_device+0xee/0x4e0 [vmwgfx]
vmw_driver_load.cold+0x757/0xd84 [vmwgfx]
drm_dev_register+0x1ff/0x340 [drm]
drm_get_pci_dev+0x110/0x290 [drm]
vmw_probe+0x15/0x20 [vmwgfx]
local_pci_probe+0x7a/0xc0
pci_device_probe+0x1b9/0x290
really_probe+0x1b5/0x630
driver_probe_device+0xa3/0x1a0
device_driver_attach+0x94/0xa0
__driver_attach+0xdd/0x1c0
bus_for_each_dev+0xfe/0x150
driver_attach+0x2d/0x40
bus_add_driver+0x290/0x350
driver_register+0xdc/0x1d0
__pci_register_driver+0xda/0xf0
vmwgfx_init+0x34/0x1000 [vmwgfx]
do_one_initcall+0xe5/0x40a
do_init_module+0x10f/0x3a0
load_module+0x16a5/0x1a40
__se_sys_finit_module+0x183/0x1c0
__x64_sys_finit_module+0x43/0x50
do_syscall_64+0xc8/0x606
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Fixes: fb1d9738ca05 ("drm/vmwgfx: Add DRM driver for VMware Virtual GPU")
Co-developed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Qian Cai <cai@lca.pw>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
|
|
Commit bf0102a0fdd9 ("riscv: call pm_power_off from machine_halt /
machine_power_off") removed the export of pm_power_off, but it is used by
several modules:
ERROR: "pm_power_off" [drivers/mfd/rk808.ko] undefined!
ERROR: "pm_power_off" [drivers/mfd/max8907.ko] undefined!
ERROR: "pm_power_off" [drivers/mfd/axp20x.ko] undefined!
ERROR: "pm_power_off" [drivers/char/ipmi/ipmi_poweroff.ko] undefined!
Signed-off-by: Andreas Schwab <schwab@suse.de>
Fixes: bf0102a0fdd9 ("riscv: call pm_power_off from machine_halt / machine_power_off")
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
|
|
When building sg tables, honor the device sg list segment size limitation.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Deepak Rawat <drawat@vmware.com>
|
|
Enable PRCI clock driver and serial console by default, so the default
upstream defconfig is bootable to a serial console.
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
|
|
The HB port may not be available for various reasons. Either it has been
disabled by a config option or by the hypervisor for other reasons.
In that case, make sure we have a backup plan and use the backdoor port
instead with a performance penalty.
Cc: stable@vger.kernel.org
Fixes: 89da76fde68d ("drm/vmwgfx: Add VMWare host messaging capability")
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Deepak Rawat <drawat@vmware.com>
|
|
If the leftmost parent node of the tree has does not have a child
on the left side, then trie_get_next_key (and bpftool map dump) will
not look at the child on the right. This leads to the traversal
missing elements.
Lookup is not affected.
Update selftest to handle this case.
Reproducer:
bpftool map create /sys/fs/bpf/lpm type lpm_trie key 6 \
value 1 entries 256 name test_lpm flags 1
bpftool map update pinned /sys/fs/bpf/lpm key 8 0 0 0 0 0 value 1
bpftool map update pinned /sys/fs/bpf/lpm key 16 0 0 0 0 128 value 2
bpftool map dump pinned /sys/fs/bpf/lpm
Returns only 1 element. (2 expected)
Fixes: b471f2f1de8b ("bpf: implement MAP_GET_NEXT_KEY command for LPM_TRIE")
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
This reverts commit d4b13963f217dd947da5c0cabd1569e914d21699.
The commit introduced a regression in glusterfs-fuse.
Reported-by: Sander Eikelenboom <linux@eikelenboom.it>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
|
|
Check for exact and correct return value to snd_i2c_sendbytes
call for EWS/DMX 6Fire (snd_ice1712).
Fixes a systemic error on every boot starting from kernel 5.1
onwards to snd_ice1712 driver ("cannot send pca") on Terratec
EWS/DMX 6Fire PCI soundcards.
Check for exact and correct return value to snd_i2c_sendbytes
call for EWS/DMX 6Fire (snd_ice1712).
Fixes a systemic error on every boot to snd_ice1712 driver
("cannot send pca") on Terratec EWS/DMX 6Fire PCI soundcards.
Fixes: c99776cc4018 ("ALSA: ice1712: fix a missing check of snd_i2c_sendbytes")
Signed-off-by: Rui Nuno Capela <rncbc@rncbc.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Stanton SCS.1m can transfer isochronous packet with Multi Bit Linear
Audio data channels, therefore it allows software to capture PCM
substream. However, ALSA oxfw driver doesn't.
This commit changes the driver to add one PCM substream for capture
direction.
Fixes: de5126cc3c0b ("ALSA: oxfw: add stream format quirk for SCS.1 models")
Cc: <stable@vger.kernel.org> # v4.5+
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The data for isochronous resources is not destroyed in expected place.
This commit fixes the bug.
Cc: <stable@vger.kernel.org> # v4.12+
Fixes: 9b2bb4f2f4a2 ("ALSA: firewire-motu: add stream management functionality")
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Hechao Li says:
====================
Getting number of possible CPUs is commonly used for per-CPU BPF maps
and perf_event_maps. Add a new API libbpf_num_possible_cpus() that
helps user with per-CPU related operations and remove duplicate
implementations in bpftool and selftests.
v2: Save errno before calling pr_warning in case it is changed.
v3: Make sure libbpf_num_possible_cpus never returns 0 so that user only
has to check if ret value < 0.
v4: Fix error code when reading 0 bytes from possible CPU file.
v5: Fix selftests compliation issue.
v6: Split commit to reuse libbpf_num_possible_cpus() into two commits:
One commit to remove bpf_util.h from test BPF C programs.
One commit to reuse libbpf_num_possible_cpus() in bpftools
and bpf_util.h.
====================
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
Use the newly added bpf_num_possible_cpus() in bpftool and selftests
and remove duplicate implementations.
Signed-off-by: Hechao Li <hechaol@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
Though currently there is no problem including bpf_util.h in kernel
space BPF C programs, in next patch in this stack, I will reuse
libbpf_num_possible_cpus() in bpf_util.h thus include libbpf.h in it,
which will cause BPF C programs compile error. Therefore I will first
remove bpf_util.h from all test BPF programs.
This can also make it clear that bpf_util.h is a user-space utility
while bpf_helpers.h is a kernel space utility.
Signed-off-by: Hechao Li <hechaol@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
Adding a new API libbpf_num_possible_cpus() that helps user with
per-CPU map operations.
Signed-off-by: Hechao Li <hechaol@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
An error "implicit declaration of function 'reallocarray'" can be thrown
with the following steps:
$ cd tools/testing/selftests/bpf
$ make clean && make CC=<Path to GCC 4.8.5>
$ make clean && make CC=<Path to GCC 7.x>
The cause is that the feature folder generated by GCC 4.8.5 is not
removed, leaving feature-reallocarray being 1, which causes reallocarray
not defined when re-compliing with GCC 7.x. This diff adds feature
folder to EXTRA_CLEAN to avoid this problem.
v2: Rephrase the commit message.
Signed-off-by: Hechao Li <hechaol@fb.com>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
s390:tinyconfig fails to build with gcc 8.3.0.
arch/s390/include/asm/ctl_reg.h:52:2: error: impossible constraint in 'asm'
asm volatile( \
^~~
arch/s390/include/asm/ctl_reg.h:62:2: note: in expansion of macro '__ctl_store'
__ctl_store(reg, cr, cr);
^~~~~~~~~~~
s390/include/asm/ctl_reg.h:41:2: error: impossible constraint in 'asm'
asm volatile( \
^~~
arch/s390/include/asm/ctl_reg.h:64:2:
note: in expansion of macro '__ctl_load'
__ctl_load(reg, cr, cr);
^~~~~~~~~~
Marking __ctl_set_bit and __ctl_clear_bit as __always_inline fixes the
problem.
Fixes: 9012d011660e ("compiler: allow all arches to enable CONFIG_OPTIMIZE_INLINING")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
|
|
Get rid of gcc9 warnings like this:
arch/s390/boot/ipl_report.c: In function 'find_bootdata_space':
arch/s390/boot/ipl_report.c:42:26: warning: taking address of packed member of 'struct ipl_rb_components' may result in an unaligned pointer value [-Waddress-of-packed-member]
42 | for_each_rb_entry(comp, comps)
| ^~~~~
This is effectively the s390 variant of commit 20c6c1890455
("x86/boot: Disable the address-of-packed-member compiler warning").
Reviewed-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
|
|
Fix signature of bpf_probe_read and bpf_probe_write_user to mark source
pointer as const. This causes warnings during compilation for
applications relying on those helpers.
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Quentin reports that commit 07c3bbdb1a9b ("samples: bpf: print
a warning about headers_install") is producing the false
positive when make is invoked locally, from the samples/bpf/
directory.
When make is run locally it hits the "all" target, which
will recursively invoke make through the full build system.
Speed up the "local" run which doesn't actually build anything,
and avoid false positives by skipping all the probes if not in
kbuild environment (cover both the new warning and the BTF
probes).
Reported-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Jonathan Lemon says:
====================
Currently, the AF_XDP code uses a separate map in order to
determine if an xsk is bound to a queue. Have the xskmap
lookup return a XDP_SOCK pointer on the kernel side, which
the verifier uses to extract relevant values.
Patches:
1 - adds XSK_SOCK type
2 - sync bpf.h with tools
3 - add tools selftest
4 - update lib/bpf, removing qidconf
v4->v5:
- xskmap lookup now returns XDP_SOCK type instead of pointer to element.
- no changes lib/bpf/xsk.c
v3->v4:
- Clarify error handling path.
v2->v3:
- Use correct map type.
====================
Acked-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Use the recent change to XSKMAP bpf_map_lookup_elem() to test if
there is a xsk present in the map instead of duplicating the work
with qidconf.
Fix things so callers using XSK_LIBBPF_FLAGS__INHIBIT_PROG_LOAD
bypass any internal bpf maps, so xsk_socket__{create|delete} works
properly.
Clean up error handling path.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Acked-by: Song Liu <songliubraving@fb.com>
Tested-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Check that bpf_map_lookup_elem lookup and structure
access operats correctly.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Sync uapi/linux/bpf.h
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Currently, the AF_XDP code uses a separate map in order to
determine if an xsk is bound to a queue. Instead of doing this,
have bpf_map_lookup_elem() return a xdp_sock.
Rearrange some xdp_sock members to eliminate structure holes.
Remove selftest - will be added back in later patch.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
