| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
parse_read_errors can be called with only oob_buf in which case
data_buf will be NULL. If data_buf is NULL, then don’t
treat this page as completely erased in case of ECC uncorrectable
error for RS ECC. For BCH ECC, the controller itself tells
regarding erased page in status register.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Following is the flow in the HW if controller tries to read erased
page:
1. First ECC uncorrectable error will be generated from ECC engine
since ECC engine first calculates the ECC with all 0xff and match
the calculated ECC with ECC code in OOB (which is again all 0xff).
2. After getting ECC error, erased CW detection logic will be
applied which is different for BCH and RS ECC
a. For BCH, HW checks if all the bytes in page are 0xff and then
it updates the status in separate register
NAND_ERASED_CW_DETECT_STATUS.
b. For RS ECC, the HW reports the same error when reading an
erased CW, but it notifies that it is an erased CW by
placing special characters at certain offsets in the
buffer.
So the erased CW detect status should be checked only if ECC engine
generated the uncorrectable error.
Currently for all other operational errors also (like TIMEOUT, MPU
errors, etc.), the erased CW detect logic is being applied so fix this
and return EIO for other operational errors.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
The BAM has 3 channels - tx, rx and command. command channel
is used for register read/writes, tx channel for data writes
and rx channel for data reads. Currently, the driver assumes the
transfer completion once it gets all the command descriptors
completed. Sometimes, there is race condition between data channel
(tx/rx) and command channel completion. In these cases,
the data present in buffer is not valid during small window
between command descriptor completion and data descriptor
completion.
This patch generates NAND transfer completion when both
(Data and Command) DMA channels have completed all its DMA
descriptors. It assigns completion callback in last
DMA descriptors of that channel and wait for completion.
Fixes: 8d6b6d7e135e ("mtd: nand: qcom: support for command descriptor formation")
Cc: stable@vger.kernel.org
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Currently the driver uses the ECC strength specified in DT.
The QPIC/EBI2 NAND supports 4 or 8-bit ECC correction. The same
kind of board can have different NAND parts so use the ECC
strength from device parameters if it is not specified in DT.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
QCOM NAND controller supports only one step size (512) so
nand-ecc-step-size DT property is redundant. This property
can be removed and ecc step size can be assigned with 512 value.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
1. If nand-ecc-strength specified in DT, then controller will use
this ECC strength otherwise ECC strength will be calculated
according to chip requirement and available OOB size.
2. QCOM NAND controller supports only one step size (512 bytes) but
nand-ecc-step-size is required property in DT. This DT property
can be removed and ecc step size can be assigned in driver with
512 bytes value.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Use the NAND core helper function nand_ecc_choose_conf to tune
the ECC parameters instead of the function locally defined.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
commit 2c8f8afa7f92 ("mtd: nand: add generic helpers to check,
match, maximize ECC settings") provides generic helpers which
drivers can use for setting up ECC parameters.
Since same board can have different ECC strength nand chips so
following is the logic for setting up ECC strength and ECC step
size, which can be used by most of the drivers.
1. If both ECC step size and ECC strength are already set
(usually by DT) then just check whether this setting
is supported by NAND controller.
2. If NAND_ECC_MAXIMIZE is set, then select maximum ECC strength
supported by NAND controller.
3. Otherwise, try to match the ECC step size and ECC strength closest
to the chip's requirement. If available OOB size can't fit the chip
requirement then select maximum ECC strength which can be fit with
available OOB size.
This patch introduces nand_ecc_choose_conf function which calls the
required helper functions for the above logic. The drivers can use
this single function instead of calling the 3 helper functions
individually.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Some Micron NAND chips (MT29F1G08ABAFAWP-ITE:F) report 00 00 for the
revision number field of the ONFI parameter page. Rather than rejecting
these outright assume ONFI version 1.0 if the revision number is 00 00.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Add defines for the ONFI version bits and use them in
nand_flash_detect_onfi().
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
This is called after the ONFI parameter page checksum is verified
and allows us to override the contents of the parameter page.
Suggested-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
>From the controllers point of view this is the same as no or
software only ECC.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Add support for the NAND flash controller found on NVIDIA
Tegra 2 SoCs. This implementation does not make use of the
command queue feature. Regular operations using ->exec_op()
use PIO mode for data transfers. Raw, ECC and OOB read/writes
make use of the DMA mode for data transfer.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
This adds the devicetree binding for the Tegra 2 NAND flash
controller.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Allow to define a NAND chip as a boot device. This can be helpful
for the selection of the ECC algorithm and strength in case the boot
ROM supports only a subset of controller provided options.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Add Reed-Solomon (RS) to the enumeration of ECC algorithms.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
The datasheet of the H27UCG8T2BTR states that this chip has a page size
of "16,384 + 1,280(Spare) bytes". The description of the "4th Byte of
Device Identifier Description" indicates that bits 6, 3 and 2 are
encoding the "Redundant Area Size / 8KB", where 640 bytes is a value of
0x6 (110 in binary notation).
hynix_nand_extract_oobsize decodes an OOB size of 640 bytes for this
chip. Kernel boot log extract before this patch:
nand: Could not find valid ONFI parameter page; aborting
nand: device found, Manufacturer ID: 0xad, Chip ID: 0xde
nand: Hynix NAND 8GiB 3,3V 8-bit
nand: 8192 MiB, MLC, erase size: 4096 KiB, page size: 16384,
OOB size: 640
However, based on the description in the datasheet we need to multiply
the OOB size with 2, because it's "640 spare bytes per 8192 bytes page
size" and this NAND chip has a page size of 16384 (= 2 * 8192). After
this patch the kernel boot log reports:
nand: Could not find valid ONFI parameter page; aborting
nand: device found, Manufacturer ID: 0xad, Chip ID: 0xde
nand: Hynix NAND 8GiB 3,3V 8-bit
nand: 8192 MiB, MLC, erase size: 4096 KiB, page size: 16384,
OOB size: 1280
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Even if we can't update ecc_stats.corrected with an accurate value we
should at least increase the number of bitflips so that MTD users can
know that there was some bitflips.
Just add chip->ecc.strength to mtd->ecc_stats.corrected which should
account for the worst case situation.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
On a sama5d31 with a Full-HD dual LVDS panel (132MHz pixel clock) NAND
flash accesses have a tendency to cause display disturbances. Add a
module param to disable DMA from the NAND controller, since that fixes
the display problem for me.
Signed-off-by: Peter Rosin <peda@axentia.se>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fixes from David Sterba:
"We have a few regression fixes for qgroup rescan status tracking and
the vm_fault_t conversion that mixed up the error values"
* tag 'for-4.18-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
Btrfs: fix mount failure when qgroup rescan is in progress
Btrfs: fix regression in btrfs_page_mkwrite() from vm_fault_t conversion
btrfs: quota: Set rescan progress to (u64)-1 if we hit last leaf
|
|
Pull vfs fix from Al Viro:
"Followup to procfs-seq_file series this window"
This fixes a memory leak by making sure that proc seq files release any
private data on close. The 'proc_seq_open' has to be properly paired
with 'proc_seq_release' that releases the extra private data.
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
proc: add proc_seq_release
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging/IIO fixes from Greg KH:
"Here are a few small staging and IIO driver fixes for 4.18-rc3.
Nothing major or big, all just fixes for reported problems since
4.18-rc1. All of these have been in linux-next this week with no
reported problems"
* tag 'staging-4.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: android: ion: Return an ERR_PTR in ion_map_kernel
staging: comedi: quatech_daqp_cs: fix no-op loop daqp_ao_insn_write()
iio: imu: inv_mpu6050: Fix probe() failure on older ACPI based machines
iio: buffer: fix the function signature to match implementation
iio: mma8452: Fix ignoring MMA8452_INT_DRDY
iio: tsl2x7x/tsl2772: avoid potential division by zero
iio: pressure: bmp280: fix relative humidity unit
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are five fixes for the tty core and some serial drivers.
The tty core ones fix some security and other issues reported by the
syzbot that I have taken too long in responding to (sorry Tetsuo!).
The 8350 serial driver fix resolves an issue of devices that used to
work properly stopping working as they shouldn't have been added to a
blacklist.
All of these have been in linux-next for a few days with no reported
issues"
* tag 'tty-4.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
vt: prevent leaking uninitialized data to userspace via /dev/vcs*
serdev: fix memleak on module unload
serial: 8250_pci: Remove stalled entries in blacklist
n_tty: Access echo_* variables carefully.
n_tty: Fix stall at n_tty_receive_char_special().
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here is a number of USB gadget and other driver fixes for 4.18-rc3.
There's a bunch of them here, most of them being gadget driver and
xhci host controller fixes for reported issues (as normal), but there
are also some new device ids, and some fixes for the typec code.
There is an acpi core patch in here that was acked by the acpi
maintainer as it is needed for the typec fixes in order to properly
solve a problem in that driver.
All of these have been in linux-next this week with no reported
issues"
* tag 'usb-4.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (33 commits)
usb: chipidea: host: fix disconnection detect issue
usb: typec: tcpm: fix logbuffer index is wrong if _tcpm_log is re-entered
typec: tcpm: Fix a msecs vs jiffies bug
NFC: pn533: Fix wrong GFP flag usage
usb: cdc_acm: Add quirk for Uniden UBC125 scanner
staging/typec: fix tcpci_rt1711h build errors
usb: typec: ucsi: Fix for incorrect status data issue
usb: typec: ucsi: acpi: Workaround for cache mode issue
acpi: Add helper for deactivating memory region
usb: xhci: increase CRS timeout value
usb: xhci: tegra: fix runtime PM error handling
usb: xhci: remove the code build warning
xhci: Fix kernel oops in trace_xhci_free_virt_device
xhci: Fix perceived dead host due to runtime suspend race with event handler
dwc2: gadget: Fix ISOC IN DDMA PID bitfield value calculation
usb: gadget: dwc2: fix memory leak in gadget_init()
usb: gadget: composite: fix delayed_status race condition when set_interface
usb: dwc2: fix isoc split in transfer with no data
usb: dwc2: alloc dma aligned buffer for isoc split in
usb: dwc2: fix the incorrect bitmaps for the ports of multi_tt hub
...
|
|
Pull dma mapping fixlet from Christoph Hellwig:
"Add a missing export required by riscv and unicore"
* tag 'dma-mapping-4.18-2' of git://git.infradead.org/users/hch/dma-mapping:
swiotlb: export swiotlb_dma_ops
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull parisc fixes and cleanups from Helge Deller:
"Nothing exiting in this patchset, just
- small cleanups of header files
- default to 4 CPUs when building a SMP kernel
- mark 16kB and 64kB page sizes broken
- addition of the new io_pgetevents syscall"
* 'parisc-4.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Build kernel without -ffunction-sections
parisc: Reduce debug output in unwind code
parisc: Wire up io_pgetevents syscall
parisc: Default to 4 SMP CPUs
parisc: Convert printk(KERN_LEVEL) to pr_lvl()
parisc: Mark 16kB and 64kB page sizes BROKEN
parisc: Drop struct sigaction from not exported header file
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"A smaller batch for the end of the week (let's see if I can keep the
weekly cadence going for once).
All medium-grade fixes here, nothing worrisome:
- Fixes for some fairly old bugs around SD card write-protect
detection and GPIO interrupt assignments on Davinci.
- Wifi module suspend fix for Hikey.
- Minor DT tweaks to fix inaccuracies for Amlogic platforms, one
of which solves booting with third-party u-boot"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
arm64: dts: hikey960: Define wl1837 power capabilities
arm64: dts: hikey: Define wl1835 power capabilities
ARM64: dts: meson-gxl: fix Mali GPU compatible string
ARM64: dts: meson-axg: fix ethernet stability issue
ARM64: dts: meson-gx: fix ATF reserved memory region
ARM64: dts: meson-gxl-s905x-p212: Add phy-supply for usb0
ARM64: dts: meson: fix register ranges for SD/eMMC
ARM64: dts: meson: disable sd-uhs modes on the libretech-cc
ARM: dts: da850: Fix interrups property for gpio
ARM: davinci: board-da850-evm: fix WP pin polarity for MMC/SD
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild fixes from Masahiro Yamada:
- introduce __diag_* macros and suppress -Wattribute-alias warnings
from GCC 8
- fix stack protector test script for x86_64
- fix line number handling in Kconfig
- document that '#' starts a comment in Kconfig
- handle P_SYMBOL property in dump debugging of Kconfig
- correct help message of LD_DEAD_CODE_DATA_ELIMINATION
- fix occasional segmentation faults in Kconfig
* tag 'kbuild-fixes-v4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
kconfig: loop boundary condition fix
kbuild: reword help of LD_DEAD_CODE_DATA_ELIMINATION
kconfig: handle P_SYMBOL in print_symbol()
kconfig: document Kconfig source file comments
kconfig: fix line numbers for if-entries in menu tree
stack-protector: Fix test with 32-bit userland and CONFIG_64BIT=y
powerpc: Remove -Wattribute-alias pragmas
disable -Wattribute-alias warning for SYSCALL_DEFINEx()
kbuild: add macro for controlling warnings to linux/compiler.h
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
"The biggest diffstat comes from self-test updates, plus there's entry
code fixes, 5-level paging related fixes, console debug output fixes,
and misc fixes"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mm: Clean up the printk()s in show_fault_oops()
x86/mm: Drop unneeded __always_inline for p4d page table helpers
x86/efi: Fix efi_call_phys_epilog() with CONFIG_X86_5LEVEL=y
selftests/x86/sigreturn: Do minor cleanups
selftests/x86/sigreturn/64: Fix spurious failures on AMD CPUs
x86/entry/64/compat: Fix "x86/entry/64/compat: Preserve r8-r11 in int $0x80"
x86/mm: Don't free P4D table when it is folded at runtime
x86/entry/32: Add explicit 'l' instruction suffix
x86/mm: Get rid of KERN_CONT in show_fault_oops()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar:
"Tooling fixes mostly, plus a build warning fix"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (21 commits)
perf/core: Move inline keyword at the beginning of declaration
tools/headers: Pick up latest kernel ABIs
perf tools: Fix crash caused by accessing feat_ops[HEADER_LAST_FEATURE]
perf script: Fix crash because of missing evsel->priv
perf script: Add missing output fields in a hint
perf bench: Fix numa report output code
perf stat: Remove duplicate event counting
perf alias: Rebuild alias expression string to make it comparable
perf alias: Remove trailing newline when reading sysfs files
perf tools: Fix a clang 7.0 compilation error
tools include uapi: Synchronize bpf.h with the kernel
tools include uapi: Update if_link.h to pick IFLA_{BRPORT_ISOLATED,VXLAN_TTL_INHERIT}
tools include powerpc: Update arch/powerpc/include/uapi/asm/unistd.h copy to get 'rseq' syscall
perf tools: Update x86's syscall_64.tbl, adding 'io_pgetevents' and 'rseq'
tools headers uapi: Synchronize drm/drm.h
perf intel-pt: Fix packet decoding of CYC packets
perf tests: Add valid callback for parse-events test
perf tests: Add event parsing error handling to parse events test
perf report powerpc: Fix crash if callchain is empty
perf test session topology: Fix test on s390
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/selinux
Pull selinux fix from Paul Moore:
"One fairly straightforward patch to fix a longstanding issue where a
process could stall while accessing files in selinuxfs and block
everyone else due to a held mutex.
The patch passes all our tests and looks to apply cleanly to your
current tree"
* tag 'selinux-pr-20180629' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/selinux:
selinux: move user accesses in selinuxfs out of locked regions
|
|
Pull block fixes from Jens Axboe:
"Small set of fixes for this series. Mostly just minor fixes, the only
oddball in here is the sg change.
The sg change came out of the stall fix for NVMe, where we added a
mempool and limited us to a single page allocation. CONFIG_SG_DEBUG
sort-of ruins that, since we'd need to account for that. That's
actually a generic problem, since lots of drivers need to allocate SG
lists. So this just removes support for CONFIG_SG_DEBUG, which I added
back in 2007 and to my knowledge it was never useful.
Anyway, outside of that, this pull contains:
- clone of request with special payload fix (Bart)
- drbd discard handling fix (Bart)
- SATA blk-mq stall fix (me)
- chunk size fix (Keith)
- double free nvme rdma fix (Sagi)"
* tag 'for-linus-20180629' of git://git.kernel.dk/linux-block:
sg: remove ->sg_magic member
drbd: Fix drbd_request_prepare() discard handling
blk-mq: don't queue more if we get a busy return
block: Fix cloning of requests with a special payload
nvme-rdma: fix possible double free of controller async event buffer
block: Fix transfer when chunk sectors exceeds max
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"Two regression fixes, and a new syscall wire-up:
- A fix for the recent conversion to time64_t in the powermac RTC
routines, which caused time to go backward.
- Another fix for fallout from the split PMD PTL conversion.
- Wire up the new io_pgetevents() syscall.
Thanks to: Aneesh Kumar K.V, Arnd Bergmann, Breno Leitao, Mathieu
Malaterre"
* tag 'powerpc-4.18-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/powermac: Fix rtc read/write functions
powerpc/mm/32: Fix pgtable_page_dtor call
powerpc: Wire up io_pgetevents
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into fixes
This fixes polarity of SD card write-protect pin on DA850 EVM
and fixes interrupt property for DA850 SoC GPIO as defined in
device-tree.
Both of these are not introduced with v4.18 merge but have
existed prior.
* tag 'davinci-fixes-for-v4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: dts: da850: Fix interrups property for gpio
ARM: davinci: board-da850-evm: fix WP pin polarity for MMC/SD
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
into fixes
ARM64: hisi fixes for 4.18
- Added power capabilities for the mmc host controller on the
hikey and hikey960 boards to avoid broken wifi.
* tag 'hisi-fixes-for-4.18' of git://github.com/hisilicon/linux-hisi:
arm64: dts: hikey960: Define wl1837 power capabilities
arm64: dts: hikey: Define wl1835 power capabilities
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into fixes
Amlogic fixes for v4.18-rc
- minor 64-bit DT fixes
* tag 'amlogic-fixes' of https://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
ARM64: dts: meson-gxl: fix Mali GPU compatible string
ARM64: dts: meson-axg: fix ethernet stability issue
ARM64: dts: meson-gx: fix ATF reserved memory region
ARM64: dts: meson-gxl-s905x-p212: Add phy-supply for usb0
ARM64: dts: meson: fix register ranges for SD/eMMC
ARM64: dts: meson: disable sd-uhs modes on the libretech-cc
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Catalin Marinas:
- The alternatives patching code uses flush_icache_range() which itself
uses alternatives. Change the code to use an unpatched variant of
cache maintenance
- Remove unnecessary ISBs from set_{pte,pmd,pud}
- perf: xgene_pmu: Fix IOB SLOW PMU parser error
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: Remove unnecessary ISBs from set_{pte,pmd,pud}
arm64: Avoid flush_icache_range() in alternatives patching code
drivers/perf: xgene_pmu: Fix IOB SLOW PMU parser error
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
- a revert because of bugzilla #200045 (and some documentation about
it)
- another regression fix in the i2c-gpio driver
- a leak fix for the i2c core
* 'i2c/for-current-fixed' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: gpio: initialize SCL to HIGH again
i2c: smbus: kill memory leak on emulated and failed DMA SMBus xfers
i2c: algos: bit: mention our experience about initial states
Revert "i2c: algo-bit: init the bus to a known state"
|
|
Pull ceph fix from Ilya Dryomov:
"A trivial dentry leak fix from Zheng"
* tag 'ceph-for-4.18-rc3' of git://github.com/ceph/ceph-client:
ceph: fix dentry leak in splice_dentry()
|
|
As suggested by Nick Piggin it seems we can drop the -ffunction-sections
compile flag, now that the kernel uses thin archives. Testing with 32-
and 64-bit kernel showed no difference in kernel size.
Suggested-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
This was introduced more than a decade ago when sg chaining was
added, but we never really caught anything with it. The scatterlist
entry size can be critical, since drivers allocate it, so remove
the magic member. Recently it's been triggering allocation stalls
and failures in NVMe.
Tested-by: Jordan Glover <Golden_Miller83@protonmail.ch>
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
- Fix crash caused by endpoint library initialization order change
(Alan Douglas)
- Fix shpchp NULL pointer dereference regression on non-ACPI platforms
(Bjorn Helgaas)
- Move PCI_DOMAINS selection to fix build regression (Lorenzo
Pieralisi)
* tag 'pci-v4.18-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: controller: Move PCI_DOMAINS selection to arch Kconfig
PCI: Initialize endpoint library before controllers
PCI: shpchp: Manage SHPC unconditionally on non-ACPI systems
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These fix up recently added features (the Kryo cpufreq driver and
performance states coverage in the generic power domains framework),
add missing documentation for a recently added sysfs knob in the
intel_pstate driver and fix an error in its documentation.
Specifics:
- Fix the initialization time error handling in the recently added
Kryo cpufreq driver (Dan Carpenter).
- Fix up the recently added coverage of performance states in the
generic power domains (genpd) framework (Viresh Kumar).
- Add missing documentation of the new hwp_dynamic_boost sysfs knob
in the intel_pstate driver (Rafael Wysocki).
- Fix incorrect sysfs path in the intel_pstate driver documentation
(Rafael Wysocki)"
* tag 'pm-4.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
Documentation: intel_pstate: Describe hwp_dynamic_boost sysfs knob
Documentation: admin-guide: intel_pstate: Fix sysfs path
PM / Domains: Rename opp_node to np
PM / Domains: Fix return value of of_genpd_opp_to_performance_state()
cpufreq: qcom-kryo: Fix error handling in probe()
|
|
Pull drm fixes from Dave Airlie:
"Nothing too major this round:
- small set of mali-dp fixes
- single meson fix
- a bunch of amdgpu fixes (one makes non-4k page sizes not be a bad
experience)"
* tag 'drm-fixes-2018-06-29' of git://anongit.freedesktop.org/drm/drm:
drm/amd/display: release spinlock before committing updates to stream
drm/amdgpu:Support new VCN FW version naming convention
drm/amdgpu: fix UBSAN: Undefined behaviour for amdgpu_fence.c
drm/meson: Fix an un-handled error path in 'meson_drv_bind_master()'
drm/amdgpu: GPU vs CPU page size fixes in amdgpu_vm_bo_split_mapping
drm/amdgpu: Count disabled CRTCs in commit tail earlier
drm/mali-dp: Rectify the width and height passed to rotmem_required()
drm/arm/malidp: Preserve LAYER_FORMAT contents when setting format
drm: mali-dp: Enable Global SE interrupts mask for DP500
drm/arm/malidp: Ensure that the crtcs are shutdown before removing any encoder/connector
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mike Snitzer:
- Fix dm core to use more efficient bio_split() instead of
bio_clone_bioset(). Also fixes splitting bio that has integrity
payload.
- Three fixes related to properly validating DAX capabilities of a
stacked DM device that will advertise DAX support.
- Update DM writecache target to use 2-factor allocator arguments. Kees
says this is the last related change for 4.18.
- Fix DM zoned target to use GFP_NOIO to avoid triggering reclaim
during IO submission (caught by lockdep).
- Fix DM thinp to gracefully recover from running out of data space
while a previous async discard completes (whereby freeing space).
- Fix DM thinp's metadata transaction commit to avoid needless work.
* tag 'for-4.18/dm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm: prevent DAX mounts if not supported
dax: check for QUEUE_FLAG_DAX in bdev_dax_supported()
pmem: only set QUEUE_FLAG_DAX for fsdax mode
dm thin: handle running out of data space vs concurrent discard
dm raid: don't use 'const' in function return
dm zoned: avoid triggering reclaim from inside dmz_map()
dm writecache: use 2-factor allocator arguments
dm thin metadata: remove needless work from __commit_transaction
dm: use bio_split() when splitting out the already processed bio
|
|
Pull single NVMe fix from Christoph.
* 'nvme-4.18' of git://git.infradead.org/nvme:
nvme-rdma: fix possible double free of controller async event buffer
|
|
Fix the test that verifies whether bio_op(bio) represents a discard
or write zeroes operation. Compile-tested only.
Cc: Philipp Reisner <philipp.reisner@linbit.com>
Cc: Lars Ellenberg <lars.ellenberg@linbit.com>
Fixes: 7435e9018f91 ("drbd: zero-out partial unaligned discards on local backend")
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Some devices have different queue limits depending on the type of IO. A
classic case is SATA NCQ, where some commands can queue, but others
cannot. If we have NCQ commands inflight and encounter a non-queueable
command, the driver returns busy. Currently we attempt to dispatch more
from the scheduler, if we were able to queue some commands. But for the
case where we ended up stopping due to BUSY, we should not attempt to
retrieve more from the scheduler. If we do, we can get into a situation
where we attempt to queue a non-queueable command, get BUSY, then
successfully retrieve more commands from that scheduler and queue those.
This can repeat forever, starving the non-queuable command indefinitely.
Fix this by NOT attempting to pull more commands from the scheduler, if
we get a BUSY return. This should also be more optimal in terms of
letting requests stay in the scheduler for as long as possible, if we
get a BUSY due to the regular out-of-tags condition.
Reviewed-by: Omar Sandoval <osandov@fb.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
io_pgetevents() will not change the signal mask. Mark it const to make
it clear and to reduce the need for casts in user code.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Avi Kivity <avi@scylladb.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
[hch: reapply the patch that got incorrectly reverted]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
