| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Temperature sensor generates electrical analog voltage from temperature
of each chain. The analog voltage is converted to digital value through
ADC. For reading temperature values fom user space, hw monitoring device
is used.
Whenever the user requests for current temperature, the driver sends WMI
command and wait for response. For reading temperature,
cat /sys/class/ieee80211/phy*/device/hwmon/hwmon2/temp1_input
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Thermal cooling device support is added to control the temperature by
throttling the data transmission for the given duration. Throttling is
done by suspending all data tx queues by given percentage of time. The
thermal device allows user to configure duty cycle.
Throttling can be disabled by setting the duty cycle to 0. The cooling
device can be found under /sys/class/thermal/cooling_deviceX/.
Corresponding soft link to this device can be found under phy folder.
/sys/class/ieee80211/phy*/device/cooling_device.
To set duty cycle as 40%,
echo 40 >/sys/class/ieee80211/phy*/device/cooling_device/cur_state
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The tid of 11a station with WMM disable reported by FW is 0x10 in
tx completion. The tid 16 is mapped to a NULL txq since buffer
MMPDU capbility is not supported. Then 11a station's airtime will
not be registered due to NULL txq check. As a results, airtime of
11a station keeps unchanged in debugfs system.
Mask the tid along with IEEE80211_QOS_CTL_TID_MASK to make it in
the valid range.
Hardwares tested : QCA9984
Firmwares tested : 10.4-3.10-00047
Signed-off-by: Yibo Zhao <yiboz@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Currently rx tid setup is happening for TID 0 and TID 16
during peer setup. And if other TID packets received for
the peer it will be redirected to rx error ring and not through
reo ring. And this rx tid configuration cannot be done
in the rx error ring path since it is a atomic context.
So moving the rx tid setup for all tids during the peer setup.
This is required to enable PN offload functionality to route
all packets through reo ring.
Co-developed-by: Tamizh Chelvam <tamizhr@codeaurora.org>
Signed-off-by: Tamizh Chelvam <tamizhr@codeaurora.org>
Signed-off-by: Govindaraj Saminathan <gsamin@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Before this change, after writing "warm_hw_reset" debugfs file, host
will send chip reset command to FW even though FW do not support this
service getting a warning print.
Though there is no FW impact before this change, this patch restricts
chip reset command sent to FW only if FW advertises the support via WMI
service bit.
Removed the redundant check and ath10k_warn() print as well.
New version FW will report chip reset service bit to host. Host allow user
to trigger WLAN chip reset only when fw report this service bit.
For older NON-TLV FW, since it do not report chip reset service bit, host
will not send chip reset command. For older TLV FW, since it report chip
reset service bit, host will send chip reset command.
Tested HW: QCA9984, WCN3990
QCA9984 FW version: WLAN.BL.3.9.0.2-00042-S-1
Signed-off-by: Yingying Tang <yintang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
When use command to read values, it crashed.
command:
dd if=/sys/kernel/debug/ieee80211/phy0/ath10k/mem_value count=1 bs=4 skip=$((0x100233))
It will call to ath10k_sdio_hif_diag_read with address = 0x4008cc and buf_len = 4.
Then system crash:
[ 1786.013258] Unable to handle kernel paging request at virtual address ffffffc00bd45000
[ 1786.013273] Mem abort info:
[ 1786.013281] ESR = 0x96000045
[ 1786.013291] Exception class = DABT (current EL), IL = 32 bits
[ 1786.013299] SET = 0, FnV = 0
[ 1786.013307] EA = 0, S1PTW = 0
[ 1786.013314] Data abort info:
[ 1786.013322] ISV = 0, ISS = 0x00000045
[ 1786.013330] CM = 0, WnR = 1
[ 1786.013342] swapper pgtable: 4k pages, 39-bit VAs, pgdp = 000000008542a60e
[ 1786.013350] [ffffffc00bd45000] pgd=0000000000000000, pud=0000000000000000
[ 1786.013368] Internal error: Oops: 96000045 [#1] PREEMPT SMP
[ 1786.013609] Process swapper/0 (pid: 0, stack limit = 0x0000000084b153c6)
[ 1786.013623] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.19.86 #137
[ 1786.013631] Hardware name: MediaTek krane sku176 board (DT)
[ 1786.013643] pstate: 80000085 (Nzcv daIf -PAN -UAO)
[ 1786.013662] pc : __memcpy+0x94/0x180
[ 1786.013678] lr : swiotlb_tbl_unmap_single+0x84/0x150
[ 1786.013686] sp : ffffff8008003c60
[ 1786.013694] x29: ffffff8008003c90 x28: ffffffae96411f80
[ 1786.013708] x27: ffffffae960d2018 x26: ffffff8019a4b9a8
[ 1786.013721] x25: 0000000000000000 x24: 0000000000000001
[ 1786.013734] x23: ffffffae96567000 x22: 00000000000051d4
[ 1786.013747] x21: 0000000000000000 x20: 00000000fe6e9000
[ 1786.013760] x19: 0000000000000004 x18: 0000000000000020
[ 1786.013773] x17: 0000000000000001 x16: 0000000000000000
[ 1786.013787] x15: 00000000ffffffff x14: 00000000000044c0
[ 1786.013800] x13: 0000000000365ba4 x12: 0000000000000000
[ 1786.013813] x11: 0000000000000001 x10: 00000037be6e9000
[ 1786.013826] x9 : ffffffc940000000 x8 : 000000000bd45000
[ 1786.013839] x7 : 0000000000000000 x6 : ffffffc00bd45000
[ 1786.013852] x5 : 0000000000000000 x4 : 0000000000000000
[ 1786.013865] x3 : 0000000000000c00 x2 : 0000000000000004
[ 1786.013878] x1 : fffffff7be6e9004 x0 : ffffffc00bd45000
[ 1786.013891] Call trace:
[ 1786.013903] __memcpy+0x94/0x180
[ 1786.013914] unmap_single+0x6c/0x84
[ 1786.013925] swiotlb_unmap_sg_attrs+0x54/0x80
[ 1786.013938] __swiotlb_unmap_sg_attrs+0x8c/0xa4
[ 1786.013952] msdc_unprepare_data+0x6c/0x84
[ 1786.013963] msdc_request_done+0x58/0x84
[ 1786.013974] msdc_data_xfer_done+0x1a0/0x1c8
[ 1786.013985] msdc_irq+0x12c/0x17c
[ 1786.013996] __handle_irq_event_percpu+0xe4/0x250
[ 1786.014006] handle_irq_event_percpu+0x28/0x68
[ 1786.014015] handle_irq_event+0x48/0x78
[ 1786.014026] handle_fasteoi_irq+0xd0/0x1a0
[ 1786.014039] __handle_domain_irq+0x84/0xc4
[ 1786.014050] gic_handle_irq+0x124/0x1a4
[ 1786.014059] el1_irq+0xb0/0x128
[ 1786.014072] cpuidle_enter_state+0x298/0x328
[ 1786.014082] cpuidle_enter+0x30/0x40
[ 1786.014094] do_idle+0x190/0x268
[ 1786.014104] cpu_startup_entry+0x24/0x28
[ 1786.014116] rest_init+0xd4/0xe0
[ 1786.014126] start_kernel+0x30c/0x38c
[ 1786.014139] Code: f8408423 f80084c3 36100062 b8404423 (b80044c3)
[ 1786.014150] ---[ end trace 3b02ddb698ea69ee ]---
[ 1786.015415] Kernel panic - not syncing: Fatal exception in interrupt
[ 1786.015433] SMP: stopping secondary CPUs
[ 1786.015447] Kernel Offset: 0x2e8d200000 from 0xffffff8008000000
[ 1786.015458] CPU features: 0x0,2188200c
[ 1786.015466] Memory Limit: none
For sdio chip, it need the memory which is kmalloc, if it is
vmalloc from ath10k_mem_value_read, then it have a memory error.
kzalloc of ath10k_sdio_hif_diag_read32 is the correct type, so
add kzalloc in ath10k_sdio_hif_diag_read to replace the buffer
which is vmalloc from ath10k_mem_value_read.
This patch only effect sdio chip.
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00029.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
When running simulate crash stress test, it happened
"failed to read from address 0x800: -110".
Test steps:
1. Run command continuous
echo soft > /sys/kernel/debug/ieee80211/phy0/ath10k/simulate_fw_crash
2. error happened and it did not begin recovery for long time.
[74377.334846] ath10k_sdio mmc1:0001:1: simulating soft firmware crash
[74378.378217] ath10k_sdio mmc1:0001:1: failed to read from address 0x800: -110
[74378.378371] ath10k_sdio mmc1:0001:1: failed to process pending SDIO interrupts: -110
It has sdio errors since it can not read MBOX_HOST_INT_STATUS_ADDRESS,
then it has to do recovery process to recovery ath10k.
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00042.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Add hardware parameters for QCA9377 sdio devices, it's now properly supported.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Currently, OTP is downloaded twice in case of "pre-cal-dt"
and "pre-cal-file" to fetch the board ID and takes around
~2 sec more boot uptime.
First OTP download happens in "ath10k_core_probe_fw" and
second in ath10k_core_start. First boot does not need OTP
download in core start when valid board id acquired.
The second OTP download is required upon core stop/start.
This patch skips the OTP download when first OTP download
has acquired a valid board id. This patch also marks board
id invalid in "ath10k_core_stop", which will force the OTP
download in ath10k_core_start and fetches valid board id.
Tested HW: QCA9984
Tested FW: 10.4-3.6-00104
Signed-off-by: Vikas Patel <vikpatel@codeaurora.org>
Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Jakub Kicinski says:
====================
ethtool: consolidate irq coalescing - part 3
Convert more drivers following the groundwork laid in a recent
patch set [1] and continued in [2]. The aim of the effort is to
consolidate irq coalescing parameter validation in the core.
This set converts 15 drivers in drivers/net/ethernet.
3 more conversion sets to come.
None of the drivers here checked all unsupported parameters.
[1] https://lore.kernel.org/netdev/20200305051542.991898-1-kuba@kernel.org/
[2] https://lore.kernel.org/netdev/20200306010602.1620354-1-kuba@kernel.org/
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject all unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject most of unsupported
parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver only rejected some of the unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Sameeh Jubran <sameehj@amazon.com>
Acked-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Let netdev_stats_to_stats64() do the copy work for us.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Clearing opts2 belongs to preparing the descriptor for DMA engine use.
Therefore move it into rtl8169_mark_to_asic().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
100GbE Intel Wired LAN Driver Updates 2020-03-10
This series contains updates to ice and iavf drivers.
Cleaned up unnecessary parenthesis, which was pointed out by Sergei
Shtylyov.
Mitch updates the iavf and ice drivers to expand the limitation on the
number of queues that the driver can support to account for the newer
800-series capabilities.
Brett cleans up the error messages for both SR-IOV and non SR-IOV use
cases. Fixed the logic when the ice driver is removed and a bare-metal
VF is passing traffic, which was causing a transmit hang on the VF.
Updated the ice driver to display "Link detected" field via ethtool,
when the driver is in safe mode. Updated ice driver to properly set
VLAN pruning when transmit anti-spoof is off.
Avinash fixed a corner case in DCB, when switching from IEEE to CEE
mode, the DCBX mode does not get properly updated.
Dave updates the logic when switching from software DCB to firmware DCB
to renegotiate DCBX to ensure the firmware agent has up to date
information about the DCB settings of the link partner.
Lukasz increases the PF's mailbox receive queue size to the maximum to
prevent potential bottleneck or slow down occurring from the PF's
mailbox receive queue being full.
Bruce updates the ice driver to use strscpy() instead of strlcpy().
Cleaned up variable names that were not very descriptive with names that
had more meaning.
Anirudh replaces the use of ENOTSUPP with EOPNOTSUPP in the ice driver.
Jake fixed up a function header comment to properly reflect the variable
size and use.
v2: Dropped patch 5 of the original series, where Tony added tunnel
offload support. Based on community feedback, the patch needed
changes, so giving Tony additional time to work on those changes and
not hold up the remaining changes in the series.
====================
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The inner pair of parentheses should be around the variable x
Fixes: 37feab6076aa ("net: dsa: mt7530: add support for port mirroring")
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Simplify ksz_common.c by using delayed_work instead of a combination of
timer and work.
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Jiri Pirko says:
====================
flow_offload: follow-ups to HW stats type patchset
This patchset includes couple of patches in reaction to the discussions
to the original HW stats patchset. The first patch is a fix,
the other two patches are basically cosmetics.
====================
Acked-by: Edward Cree <ecree@solarflare.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
flow_action_hw_stats_types_check()
The intention of this helper was to allow driver to specify one type
that it supports, so not only "any" value would pass. So make the API
more strict and allow driver to pass only 1 bit that is going
to be checked.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Put the values into enum and add an enum to define the bits.
Suggested-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Change the check to see if the passed allowed type bit is enabled.
Fixes: 319a1d19471e ("flow_offload: check for basic action hw stats type")
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Claudiu Manoil says:
====================
enetc: Support extended BD rings at runtime
First two patches are just misc code cleanup.
The 3rd patch prepares the Rx BD processing code to be extended
to processing both normal and extended BDs.
The last one adds extended Rx BD support for timestamping
without the need of a static config. Finally, the config option
FSL_ENETC_HW_TIMESTAMPING can be dropped.
Care was taken not to impact non-timestamping usecases.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Hardware timestamping support (PTP) on Rx requires extended
buffer descriptors, double the size of normal Rx descriptors.
On the current controller revision only the timestamping offload
requires extended Rx descriptors.
Since Rx timestamping can be turned on/off at runtime, make Rx ring
allocation configurable at runtime too. As a result, the static
config option FSL_ENETC_HW_TIMESTAMPING can be dropped and the
extended descriptors can be used only when Rx timestamping gets
activated.
The extension has the same size as the base descriptor, making
the descriptor iterators easy to update for the extended case.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Improve maintainability of the code iterating the Rx buffer
descriptors to prepare it to support iterating extended Rx BD
descriptors as well.
Don't increment by one the h/w descriptor pointers explicitly,
provide an iterator that takes care of the h/w details.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Refactor the stats len computation code to make it easier
to add new stats counters.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The existence of the DT port node is the first thing checked
at probe time, and probing won't reach this point if the node
is missing.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When pktgen is used to measure the performance of dev_queue_xmit()
packet handling in the core, it is preferable to not hand down
packets to a low-level Ethernet driver as it would distort the
measurements.
Allow using pktgen on the loopback device, thus constraining
measurements to core code.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
flow_action_mixed_hw_stats_types_check()
Instead of manually iterating over entries, use flow_action_for_each
helper. Move the helper and wrap it to fit to 80 cols on the way.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The function comment for ice_get_nvm_version indicated that the ver_hi
and ver_lo values were 16 bits. In fact, they are only uint8_t values,
meaning that they have a maximum size of 8 bits. Fix the comment to
match the correct size.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The variable name 'type' is not very descriptive. Replace instances of
those with a variable name that is more descriptive or replace it if not
needed.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Using ENOTSUPP almost always results in some bizarre error message to
be printed in userspace. This is likely because ENOTSUPP was defined for
the NFS protocol (as per a comment in include/linux/errno.h). Use
EOPNOTSUPP instead.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Commit ed5a3f664c55 ("ice: Removing hung_queue variable to use txqueue
function parameter") began utilizing the txqueue variable over the
hung_queue variable. hung_queue was an int where txqueue is an unsigned
int. Update the format specifiers to reflect the new type.
Fixes: ed5a3f664c55 ("ice: Removing hung_queue variable to use txqueue function parameter")
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
checkpatch complains "CHECK:DEPRECATED_API: Deprecated use of 'strlcpy',
prefer 'stracpy or strscpy' instead"; use strscpy.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Currently the PF's mailbox receive queue is only 512 entries. This fine,
but considering that all VF's mailbox send queues funnel into the PF's
single mailbox receive queue, let's increase it to the maximum size. This
will help prevent any possible bottleneck/slowdown occurring from the PF's
mailbox receive queue being full.
Signed-off-by: Lukasz Czapnik <lukasz.czapnik@intel.com>
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
VLAN pruning is not always being set correctly due to a previous change
that set Tx antispoof off. ice_vsi_is_vlan_pruning_ena() currently checks
for both Tx antispoof and Rx pruning. The expectation for this function is
to only check Rx pruning so fix the check.
Fixes: cd6d6b83316a ("ice: Fix VF spoofchk")
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
When switching from SW DCB to FW DCB it is necessary
to renegotiate DCBx so that the FW agent can have up
to date information about the DCB settings of the link
partner.
Perform an autoneg restart on the link when activating
FW DCB.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
While testing DCB for a corner case in which mode is switched from IEEE to
CEE and pfc_ena bitmask unchanged then DCBX mode doesn't get updated.
This is happening because the function ice_dcb_get_mode() is called
in a "no change detected block" instead of "change detected block".
Signed-off-by: Avinash JD <avinash.dayanand@intel.com>
Signed-off-by: Scott Register <scottx.register@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
