| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The ni65 and lance ethernet drivers manually program the ISA DMA
controller that is only available on x86 PCs and a few compatible
systems. Trying to build it on ARM results in this error:
ni65.c: In function 'ni65_probe1':
ni65.c:496:62: error: 'DMA1_STAT_REG' undeclared (first use in this function)
((inb(DMA1_STAT_REG) >> 4) & 0x0f)
^
ni65.c:496:62: note: each undeclared identifier is reported only once for each function it appears in
ni65.c:497:63: error: 'DMA2_STAT_REG' undeclared (first use in this function)
| (inb(DMA2_STAT_REG) & 0xf0);
The DMA1_STAT_REG and DMA2_STAT_REG registers are only defined for
alpha, mips, parisc, powerpc and x86, although it is not clear
which subarchitectures actually have them at the correct location.
This patch for now just disables it for ARM, to avoid randconfig
build errors. We could also decide to limit it to the set of
architectures on which it does compile, but that might look more
deliberate than guessing based on where the drivers build.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The cosa driver is rather outdated and does not get built on most
platforms because it requires the ISA_DMA_API symbol. However
there are some ARM platforms that have ISA_DMA_API but no virt_to_bus,
and they get this build error when enabling the ltpc driver.
drivers/net/wan/cosa.c: In function 'tx_interrupt':
drivers/net/wan/cosa.c:1768:3: error: implicit declaration of function 'virt_to_bus'
unsigned long addr = virt_to_bus(cosa->txbuf);
^
The same problem exists for the Hostess SV-11 and Sealevel Systems 4021
drivers.
This adds another dependency in Kconfig to avoid that configuration.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The cs89x0 driver can either be built as an ISA driver or a platform
driver, the choice is controlled by the CS89x0_PLATFORM Kconfig
symbol. Building the ISA driver on a system that does not have
a way to map I/O ports fails with this error:
drivers/built-in.o: In function `cs89x0_ioport_probe.constprop.1':
:(.init.text+0x4794): undefined reference to `ioport_map'
:(.init.text+0x4830): undefined reference to `ioport_unmap'
This changes the Kconfig logic to take that option away and
always force building the platform variant of this driver if
CONFIG_HAS_IOPORT_MAP is not set. This is the only correct
choice in this case, and it avoids the build error.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
pull-request: can-next 2015-28-01
this is a pull request of 12 patches for net-next/master.
There are 3 patches by Ahmed S. Darwish, which update the kvaser_usb
driver and add support for the USBcan-II based adapters. Stéphane
Grosjean contributes 7 patches for the peak_usb driver, which add
support for the CANFD USB adapters. I contribute 2 patches which clean
up the peak_usb driver structure a bit.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since commit cd1e65044d44 ("of/device: Don't register disabled
devices"), the disabled device will not be registered at all. So we
don't need to do the check again in the platform device driver.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When we've run out of space in the output buffer to store more data, we
will call zlib_deflate with a NULL output buffer until we've consumed
remaining input.
When this happens, olen contains the size the output buffer would have
consumed iff we'd have had enough room.
This can later cause skb_over_panic when ppp_generic skb_put()s
the returned length.
Reported-by: Iain Douglas <centos@1n6.org.uk>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When many pf_packet listeners are created on a lot of interfaces the
current implementation using global packet type lists scales poorly.
This patch adds per net_device packet type lists to fix this problem.
The patch was originally written by Eric Biederman for linux-2.6.29.
Tested on linux-3.16.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Salam Noureddine <noureddine@arista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When handling a fault in stage-2, we need to resync I$ and D$, just
to be sure we don't leave any old cache line behind.
That's very good, except that we do so using the *user* address.
Under heavy load (swapping like crazy), we may end up in a situation
where the page gets mapped in stage-2 while being unmapped from
userspace by another CPU.
At that point, the DC/IC instructions can generate a fault, which
we handle with kvm->mmu_lock held. The box quickly deadlocks, user
is unhappy.
Instead, perform this invalidation through the kernel mapping,
which is guaranteed to be present. The box is much happier, and so
am I.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
|
|
Let's assume a guest has created an uncached mapping, and written
to that page. Let's also assume that the host uses a cache-coherent
IO subsystem. Let's finally assume that the host is under memory
pressure and starts to swap things out.
Before this "uncached" page is evicted, we need to make sure
we invalidate potential speculated, clean cache lines that are
sitting there, or the IO subsystem is going to swap out the
cached view, loosing the data that has been written directly
into memory.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
|
|
Trying to emulate the behaviour of set/way cache ops is fairly
pointless, as there are too many ways we can end-up missing stuff.
Also, there is some system caches out there that simply ignore
set/way operations.
So instead of trying to implement them, let's convert it to VA ops,
and use them as a way to re-enable the trapping of VM ops. That way,
we can detect the point when the MMU/caches are turned off, and do
a full VM flush (which is what the guest was trying to do anyway).
This allows a 32bit zImage to boot on the APM thingy, and will
probably help bootloaders in general.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
|
|
When IFLA_LINK_NETNSID is used, the netdevice should be built in this link netns
and moved at the end to another netns (pointed by the socket netns or
IFLA_NET_NS_[PID|FD]).
Existing user of the newlink handler will use the netns argument (src_net) to
find a link netdevice or to check some other information into the link netns.
For example, to find a netdevice, two information are required: an ifindex
(usually from IFLA_LINK) and a netns (this link netns).
Note: when using IFLA_LINK_NETNSID and IFLA_NET_NS_[PID|FD], a user may create a
netdevice that stands in netnsX and with its link part in netnsY, by sending a
rtnl message from netnsZ.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Nicolas Dichtel says:
====================
netns: audit netdevice creation with IFLA_NET_NS_[PID|FD]
When one of these attributes is set, the netdevice is created into the netns
pointed by IFLA_NET_NS_[PID|FD] (see the call to rtnl_create_link() in
rtnl_newlink()). Let's call this netns the dest_net. After this creation, if the
newlink handler exists, it is called with a netns argument that points to the
netns where the netlink message has been received (called src_net in the code)
which is the link netns.
Hence, with one of these attributes, it's possible to create a x-netns
netdevice.
Here is the result of my code review:
- all ip tunnels (sit, ipip, ip6_tunnels, gre[tap][v6], ip_vti[6]) does not
really allows to use this feature: the netdevice is created in the dest_net
and the src_net is completely ignored in the newlink handler.
- VLAN properly handles this x-netns creation.
- bridge ignores src_net, which seems fine (NETIF_F_NETNS_LOCAL is set).
- CAIF subsystem is not clear for me (I don't know how it works), but it seems
to wrongly use src_net. Patch #1 tries to fix this, but it was done only by
code review (and only compile-tested), so please carefully review it. I may
miss something.
- HSR subsystem uses src_net to parse IFLA_HSR_SLAVE[1|2], but the netdevice has
the flag NETIF_F_NETNS_LOCAL, so the question is: does this netdevice really
supports x-netns? If not, the newlink handler should use the dest_net instead
of src_net, I can provide the patch.
- ieee802154 uses also src_net and does not have NETIF_F_NETNS_LOCAL. Same
question: does this netdevice really supports x-netns?
- bonding ignores src_net and flag NETIF_F_NETNS_LOCAL is set, ie x-netns is not
supported. Fine.
- CAN does not support rtnl/newlink, ok.
- ipvlan uses src_net and does not have NETIF_F_NETNS_LOCAL. After looking at
the code, it seems that this drivers support x-netns. Am I right?
- macvlan/macvtap uses src_net and seems to have x-netns support.
- team ignores src_net and has the flag NETIF_F_NETNS_LOCAL, ie x-netns is not
supported. Ok.
- veth uses src_net and have x-netns support ;-) Ok.
- VXLAN didn't properly handle this. The link netns (vxlan->net) is the src_net
and not dest_net (see patch #2). Note that it was already possible to create a
x-netns vxlan before the commit f01ec1c017de ("vxlan: add x-netns support")
but the nedevice remains broken.
To summarize:
- CAIF patch must be carefully reviewed
- for HSR, ieee802154, ipvlan: is x-netns supported?
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Rename the netns to src_net to avoid confusion with the netns where the
interface stands. The user may specify IFLA_NET_NS_[PID|FD] to create
a x-netns netndevice: IFLA_NET_NS_[PID|FD] points to the netns where the
netdevice stands and src_net to the link netns.
Note that before commit f01ec1c017de ("vxlan: add x-netns support"), it was
possible to create a x-netns vxlan netdevice, but the netdevice was not
operational.
Fixes: f01ec1c017de ("vxlan: add x-netns support")
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
src_net points to the netns where the netlink message has been received. This
netns may be different from the netns where the interface is created (because
the user may add IFLA_NET_NS_[PID|FD]). In this case, src_net is the link netns.
It seems wrong to override the netns in the newlink() handler because if it
was not already src_net, it means that the user explicitly asks to create the
netdevice in another netns.
CC: Sjur Brændeland <sjur.brandeland@stericsson.com>
CC: Dmitry Tarnyagin <dmitry.tarnyagin@lockless.no>
Fixes: 8391c4aab1aa ("caif: Bugfixes in CAIF netdevice for close and flow control")
Fixes: c41254006377 ("caif-hsi: Add rtnl support")
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixed commit added from64to32 under _#ifndef do_csum_ but used it
under _#ifndef csum_tcpudp_nofold_, breaking some builds (Fengguang's
robot reported TILEGX's). Move from64to32 under the latter.
Fixes: 150ae0e94634 ("lib/checksum.c: fix carry in csum_tcpudp_nofold")
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Karl Beldan <karl.beldan@rivierawaves.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"This batch ended up being larger than wished, but there is nothing to
worry too much there.
Most of commits are for ASoC, a compress NULL dereference fix, a fix
for probe error handling, and the rest are device-specific fixes. In
addition, we have a fix for a long-standing but of seq-dummy driver,
which just cuts off the buggy part in the end"
* tag 'sound-3.19-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: seq-dummy: remove deadlock-causing events on close
ASoC: omap-mcbsp: Correct CBM_CFS dai format configuration
ASoC: soc-compress.c: fix NULL dereference
ASoC: rt286: set the same format for dac and adc
ASoC: wm8904: fix runtime warning
ASoC: simple-card: Fix crash in asoc_simple_card_unref()
ASoC: fsl: imx-wm8962: Set the card owner field
ASoC: pcm512x: Fix DSP program selection
ASoC: rt5677: Modify the behavior that updates the PLL parameter.
ASoC: fsl_ssi: Fix irq error check
ASoC: rockchip: i2s: applys rate symmetry for CPU DAI
ASoC: Intel: Add NULL checks for the stream pointer
ASoC: wm8960: Fix capture sample rate from 11250 to 11025
ASoC: adi: Add missing return statement.
ASoC: Intel: Don't change offset of block allocator during fixed allocate
ASoC: ts3a227e: Check and report jack status at probe
ASoC: fsl_esai: Fix incorrect xDC field width of xCCR registers
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull final pin control fix from Linus Walleij:
"A late pin control fix for the v3.19 series: The AT91 gpio controller
would miss wakeup events, this single fix make it work properly"
[ "Final"? Yeah, I'll believe that once I've actually released 3.19 ;) - Linus ]
* tag 'pinctrl-v3.19-4' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: at91: allow to have disabled gpio bank
|
|
The stack guard page error case has long incorrectly caused a SIGBUS
rather than a SIGSEGV, but nobody actually noticed until commit
fee7e49d4514 ("mm: propagate error from stack expansion even for guard
page") because that error case was never actually triggered in any
normal situations.
Now that we actually report the error, people noticed the wrong signal
that resulted. So far, only the test suite of libsigsegv seems to have
actually cared, but there are real applications that use libsigsegv, so
let's not wait for any of those to break.
Reported-and-tested-by: Takashi Iwai <tiwai@suse.de>
Tested-by: Jan Engelhardt <jengelh@inai.de>
Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com> # "s390 still compiles and boots"
Cc: linux-arch@vger.kernel.org
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The Bluetooth controllers from Atheros use a strict scanning filter
policy that filters based on Bluetooth device addresses and not on
RSSI. So tell the core about this.
Signed-off-by: Jakub Pawlowski <jpawlowski@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Commit 4bb25789ed28228a ("arm: dma-mapping: plumb our iommu mapping ops
into arch_setup_dma_ops") moved the setting of the DMA operations from
arm_iommu_attach_device() to arch_setup_dma_ops() where the DMA
operations to be used are selected based on whether the device is
connected to an IOMMU. However, the IOMMU detection scheme requires the
IOMMU driver to be ported to the new IOMMU of_xlate API. As no driver
has been ported yet, this effectively breaks all IOMMU ARM users that
depend on the IOMMU being handled transparently by the DMA mapping API.
Fix this by restoring the setting of DMA IOMMU ops in
arm_iommu_attach_device() and splitting the rest of the function into a
new internal __arm_iommu_attach_device() function, called by
arch_setup_dma_ops().
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
The core VM already knows about VM_FAULT_SIGBUS, but cannot return a
"you should SIGSEGV" error, because the SIGSEGV case was generally
handled by the caller - usually the architecture fault handler.
That results in lots of duplication - all the architecture fault
handlers end up doing very similar "look up vma, check permissions, do
retries etc" - but it generally works. However, there are cases where
the VM actually wants to SIGSEGV, and applications _expect_ SIGSEGV.
In particular, when accessing the stack guard page, libsigsegv expects a
SIGSEGV. And it usually got one, because the stack growth is handled by
that duplicated architecture fault handler.
However, when the generic VM layer started propagating the error return
from the stack expansion in commit fee7e49d4514 ("mm: propagate error
from stack expansion even for guard page"), that now exposed the
existing VM_FAULT_SIGBUS result to user space. And user space really
expected SIGSEGV, not SIGBUS.
To fix that case, we need to add a VM_FAULT_SIGSEGV, and teach all those
duplicate architecture fault handlers about it. They all already have
the code to handle SIGSEGV, so it's about just tying that new return
value to the existing code, but it's all a bit annoying.
This is the mindless minimal patch to do this. A more extensive patch
would be to try to gather up the mostly shared fault handling logic into
one generic helper routine, and long-term we really should do that
cleanup.
Just from this patch, you can generally see that most architectures just
copied (directly or indirectly) the old x86 way of doing things, but in
the meantime that original x86 model has been improved to hold the VM
semaphore for shorter times etc and to handle VM_FAULT_RETRY and other
"newer" things, so it would be a good idea to bring all those
improvements to the generic case and teach other architectures about
them too.
Reported-and-tested-by: Takashi Iwai <tiwai@suse.de>
Tested-by: Jan Engelhardt <jengelh@inai.de>
Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com> # "s390 still compiles and boots"
Cc: linux-arch@vger.kernel.org
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
BugLink: https://bugs.launchpad.net/bugs/1400215
ath3k devices fail to load firmwares on xHCI buses, but work well on
EHCI, this might be a compatibility issue between xHCI and ath3k chips.
As my testing result, those chips will work on xHCI buses again with
this patch.
This workaround is from Qualcomm, they also did some workarounds in
Windows driver.
Signed-off-by: Adam Lee <adam.lee@canonical.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
The kobject memory inside blk-mq hctx/ctx shouldn't have been freed
before the kobject is released because driver core can access it freely
before its release.
We can't do that in all ctx/hctx/mq_kobj's release handler because
it can be run before blk_cleanup_queue().
Given mq_kobj shouldn't have been introduced, this patch simply moves
mq's release into blk_release_queue().
Reported-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
This reverts commit 76d697d10769048e5721510100bf3a9413a56385.
The commit 76d697d10769048 causes general protection fault
reported from Bart Van Assche:
https://lkml.org/lkml/2015/1/28/334
Reported-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
This command should only be used if remote device reports that it
supports extended features. Otherwise command will fail and connection
will be dropped.
Some devices support SSP but don't support extended features so
current check for SSP support is not enought.
Instead of checking for SSP support just check if both ends support
Extended Feature.
< HCI Command: Create Connection (0x01|0x0005) plen 13
Address: D0:9C:30:00:19:6F (Foster Electric Company, Limited)
Packet type: 0xcc18
DM1 may be used
DH1 may be used
DM3 may be used
DH3 may be used
DM5 may be used
DH5 may be used
Page scan repetition mode: R1 (0x01)
Page scan mode: Mandatory (0x00)
Clock offset: 0x94c8
Role switch: Allow slave (0x01)
> HCI Event: Command Status (0x0f) plen 4
Create Connection (0x01|0x0005) ncmd 1
Status: Success (0x00)
> HCI Event: Connect Complete (0x03) plen 11
Status: Success (0x00)
Handle: 5
Address: D0:9C:30:00:19:6F (Foster Electric Company, Limited)
Link type: ACL (0x01)
Encryption: Disabled (0x00)
< HCI Command: Read Remote Supported Features (0x01|0x001b) plen 2
Handle: 5
> HCI Event: Command Status (0x0f) plen 4
Read Remote Supported Features (0x01|0x001b) ncmd 1
Status: Success (0x00)
> HCI Event: Page Scan Repetition Mode Change (0x20) plen 7
Address: D0:9C:30:00:19:6F (Foster Electric Company, Limited)
Page scan repetition mode: R1 (0x01)
> HCI Event: Read Remote Supported Features (0x0b) plen 11
Status: Success (0x00)
Handle: 5
Features: 0xff 0xff 0x8f 0xfe 0xdb 0xff 0x5b 0x07
3 slot packets
5 slot packets
Encryption
Slot offset
Timing accuracy
Role switch
Hold mode
Sniff mode
Park state
Power control requests
Channel quality driven data rate (CQDDR)
SCO link
HV2 packets
HV3 packets
u-law log synchronous data
A-law log synchronous data
CVSD synchronous data
Paging parameter negotiation
Power control
Transparent synchronous data
Broadcast Encryption
Enhanced Data Rate ACL 2 Mbps mode
Enhanced Data Rate ACL 3 Mbps mode
Enhanced inquiry scan
Interlaced inquiry scan
Interlaced page scan
RSSI with inquiry results
Extended SCO link (EV3 packets)
EV4 packets
EV5 packets
AFH capable slave
AFH classification slave
LE Supported (Controller)
3-slot Enhanced Data Rate ACL packets
5-slot Enhanced Data Rate ACL packets
Sniff subrating
Pause encryption
AFH capable master
AFH classification master
Enhanced Data Rate eSCO 2 Mbps mode
Enhanced Data Rate eSCO 3 Mbps mode
3-slot Enhanced Data Rate eSCO packets
Extended Inquiry Response
Simultaneous LE and BR/EDR (Controller)
Secure Simple Pairing
Encapsulated PDU
Non-flushable Packet Boundary Flag
Link Supervision Timeout Changed Event
Inquiry TX Power Level
Enhanced Power Control
< HCI Command: Read Remote Extended Features (0x01|0x001c) plen 3
Handle: 5
Page: 1
> HCI Event: Command Status (0x0f) plen 4
Read Remote Extended Features (0x01|0x001c) ncmd 1
Status: Command Disallowed (0x0c)
< HCI Command: Read Clock Offset (0x01|0x001f) plen 2
Handle: 5
> HCI Event: Command Status (0x0f) plen 4
Read Clock Offset (0x01|0x001f) ncmd 1
Status: Success (0x00)
< HCI Command: Disconnect (0x01|0x0006) plen 3
Handle: 5
Reason: Remote User Terminated Connection (0x13)
Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Such a feature doesn't exist and isn't really needed since you
probably won't have enough interfaces to make it worthwhile, so
just remove that from the documentation.
Reported-by: booto [on IRC]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The recently added ARM_KERNMEM_PERMS feature works by manipulating
the kernel page tables, which obviously requires an MMU. Trying
to enable this feature when the MMU is disabled results in a lot
of compile errors in mm/init.c, so let's add a Kconfig dependency
to avoid that case.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Minimal builds for v7M are broken when printk is disabled. The caller is
assembly so add the necessary ifdef around the call.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
There is currently a hardcoded limit of 64KB for the DTB to live in and
be extended with ATAG info. Some DTBs have outgrown that limit:
$ du -b arch/arm/boot/dts/omap3-n900.dtb
70212 arch/arm/boot/dts/omap3-n900.dtb
Furthermore, the actual size passed to atags_to_fdt() included the stack
size which is obviously wrong.
The initial DTB size is known, so use it to size the allocated workspace
with a 50% growth assumption and relocate the temporary stack above that.
This is also clamped to 32KB min / 1MB max for robustness against bad
DTB data.
Reported-by: Pali Rohár <pali.rohar@gmail.com>
Tested-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
When tearing down the DMA ops for a device via of_dma_deconfigure, we
unconditionally detach the device from its IOMMU domain. For devices
that aren't actually behind an IOMMU, this produces a "Not attached"
warning message on the console.
This patch changes the teardown code so that we don't detach from the
IOMMU domain when there isn't an IOMMU dma mapping to start with.
Reported-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
As of commit 9a1091ef0017c40a ("irqchip: gic: Support hierarchy irq
domain."), the Lager legacy board support is known to be broken.
The IRQ numbers of the GIC are now virtual, and no longer match the
hardcoded hardware IRQ numbers in the legacy platform board code.
To fix this issue specific to non-multiplatform r8a7790 and Lager:
1) Instantiate the GIC from platform board code and also
2) Skip over the DT arch timer as well as
3) Force delay setup based on DT CPU frequency
With these 3 fixes in place interrupts on Lager are now unbroken.
Partially based on legacy GIC fix by Geert Uytterhoeven, thanks to
him for the initial work.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
The Bluetooth HCI transport specification for USB device defines on how
a standard AMP controller is identified and operated. This patch adds
the needed handling to hook it up to the Bluetooth stack.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
When I added sk_pacing_rate field, I forgot to initialize its value
in the per cpu unicast_sock used in ip_send_unicast_reply()
This means that for sch_fq users, RST packets, or ACK packets sent
on behalf of TIME_WAIT sockets might be sent to slowly or even dropped
once we reach the per flow limit.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Fixes: 95bd09eb2750 ("tcp: TSO packets automatic sizing")
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
TIME_WAIT sockets are not owning any skb.
ip_send_unicast_reply() and tcp_v6_send_response() both use
regular sockets.
We can safely remove a test in sch_fq and save one cache line miss,
as sk_state is far away from sk_pacing_rate.
Tested at Google for about one year.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
NET_ACT_CONNMARK fails to build if NF_CONNTRACK_MARK is disabled,
and d7924450e14ea4 ("act_connmark: Add missing dependency on
NF_CONNTRACK_MARK") fixed that case, but missed the cased where
NF_CONNTRACK is a loadable module.
This adds the second dependency to ensure that NET_ACT_CONNMARK
can only be built-in if NF_CONNTRACK is also part of the kernel
rather than a loadable module.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The sock_iocb structure is allocate on stack for each read/write-like
operation on sockets, and contains various fields of which only the
embedded msghdr and sometimes a pointer to the scm_cookie is ever used.
Get rid of the sock_iocb and put a msghdr directly on the stack and pass
the scm_cookie explicitly to netlink_mmap_sendmsg.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The if block was supposed to have curly braces. In the current code we
complain about dropped rx packets when we shouldn't.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, it isn't possible to request checksums on the outer UDP
header of tunnels - the TUNNEL_CSUM flag is ignored. This adds
support for requesting that UDP checksums be computed on transmit
and properly reported if they are present on receive.
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sameo/nfc-next
NFC: 3.20 first pull request
This is the first NFC pull request for 3.20.
With this one we have:
- Secure element support for the ST Micro st21nfca driver. This depends
on a few HCI internal changes in order for example to support more
than one secure element per controller.
- ACPI support for NXP's pn544 HCI driver. This controller is found on
many x86 SoCs and is typically enumerated on the ACPI bus there.
- A few st21nfca and st21nfcb fixes.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The carry from the 64->32bits folding was dropped, e.g with:
saddr=0xFFFFFFFF daddr=0xFF0000FF len=0xFFFF proto=0 sum=1,
csum_tcpudp_nofold returned 0 instead of 1.
Signed-off-by: Karl Beldan <karl.beldan@rivierawaves.com>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: stable@vger.kernel.org
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Intel Bluetooth devices use the generic USB device/interface class
descriptors that are assigned to Bluetooth H:2 conforming transports.
T: Bus=01 Lev=01 Prnt=01 Port=01 Cnt=02 Dev#= 3 Spd=12 MxCh= 0
D: Ver= 2.01 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
However newer chips have a bootloader stage and require firmware to
be loaded before they are functional. To avoid any confusion for the
users, just ignore unknown Intel Bluetooth devices.
All the released Intel Bluetooth devices have an entry in the device
table identifying their setup and support requirements. The advantage
here is that older kernel can be booted with newer devices without
causing any disturbance.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
New entries to the USB blacklist/quirk device table should be sorted
by USB vendor id. Fix the recent entry fro Marvell devices.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
Reported in: https://bugzilla.kernel.org/show_bug.cgi?id=92081
This patch avoids calling rtnl_notify if the device ndo_bridge_getlink
handler does not return any bytes in the skb.
Alternately, the skb->len check can be moved inside rtnl_notify.
For the bridge vlan case described in 92081, there is also a fix needed
in bridge driver to generate a proper notification. Will fix that in
subsequent patch.
v2: rebase patch on net tree
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Neal Cardwell says:
====================
fix stretch ACK bugs in TCP CUBIC and Reno
This patch series fixes the TCP CUBIC and Reno congestion control
modules to properly handle stretch ACKs in their respective additive
increase modes, and in the transitions from slow start to additive
increase.
This finishes the project started by commit 9f9843a751d0a2057 ("tcp:
properly handle stretch acks in slow start"), which fixed behavior for
TCP congestion control when handling stretch ACKs in slow start mode.
Motivation: In the Jan 2015 netdev thread 'BW regression after "tcp:
refine TSO autosizing"', Eyal Perry documented a regression that Eric
Dumazet determined was caused by improper handling of TCP stretch
ACKs.
Background: LRO, GRO, delayed ACKs, and middleboxes can cause "stretch
ACKs" that cover more than the RFC-specified maximum of 2
packets. These stretch ACKs can cause serious performance shortfalls
in common congestion control algorithms, like Reno and CUBIC, which
were designed and tuned years ago with receiver hosts that were not
using LRO or GRO, and were instead ACKing every other packet.
Testing: at Google we have been using this approach for handling
stretch ACKs for CUBIC datacenter and Internet traffic for several
years, with good results.
v2:
* fixed return type of tcp_slow_start() to be u32 instead of int
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes a bug in CUBIC that causes cwnd to increase slightly
too slowly when multiple ACKs arrive in the same jiffy.
If cwnd is supposed to increase at a rate of more than once per jiffy,
then CUBIC was sometimes too slow. Because the bic_target is
calculated for a future point in time, calculated with time in
jiffies, the cwnd can increase over the course of the jiffy while the
bic_target calculated as the proper CUBIC cwnd at time
t=tcp_time_stamp+rtt does not increase, because tcp_time_stamp only
increases on jiffy tick boundaries.
So since the cnt is set to:
ca->cnt = cwnd / (bic_target - cwnd);
as cwnd increases but bic_target does not increase due to jiffy
granularity, the cnt becomes too large, causing cwnd to increase
too slowly.
For example:
- suppose at the beginning of a jiffy, cwnd=40, bic_target=44
- so CUBIC sets:
ca->cnt = cwnd / (bic_target - cwnd) = 40 / (44 - 40) = 40/4 = 10
- suppose we get 10 acks, each for 1 segment, so tcp_cong_avoid_ai()
increases cwnd to 41
- so CUBIC sets:
ca->cnt = cwnd / (bic_target - cwnd) = 41 / (44 - 41) = 41 / 3 = 13
So now CUBIC will wait for 13 packets to be ACKed before increasing
cwnd to 42, insted of 10 as it should.
The fix is to avoid adjusting the slope (determined by ca->cnt)
multiple times within a jiffy, and instead skip to compute the Reno
cwnd, the "TCP friendliness" code path.
Reported-by: Eyal Perry <eyalpe@mellanox.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Change CUBIC to properly handle stretch ACKs in additive increase mode
by passing in the count of ACKed packets to tcp_cong_avoid_ai().
In addition, because we are now precisely accounting for stretch ACKs,
including delayed ACKs, we can now remove the delayed ACK tracking and
estimation code that tracked recent delayed ACK behavior in
ca->delayed_ack.
Reported-by: Eyal Perry <eyalpe@mellanox.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Change Reno to properly handle stretch ACKs in additive increase mode
by passing in the count of ACKed packets to tcp_cong_avoid_ai().
In addition, if snd_cwnd crosses snd_ssthresh during slow start
processing, and we then exit slow start mode, we need to carry over
any remaining "credit" for packets ACKed and apply that to additive
increase by passing this remaining "acked" count to
tcp_cong_avoid_ai().
Reported-by: Eyal Perry <eyalpe@mellanox.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
tcp_cong_avoid_ai() was too timid (snd_cwnd increased too slowly) on
"stretch ACKs" -- cases where the receiver ACKed more than 1 packet in
a single ACK. For example, suppose w is 10 and we get a stretch ACK
for 20 packets, so acked is 20. We ought to increase snd_cwnd by 2
(since acked/w = 20/10 = 2), but instead we were only increasing cwnd
by 1. This patch fixes that behavior.
Reported-by: Eyal Perry <eyalpe@mellanox.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
LRO, GRO, delayed ACKs, and middleboxes can cause "stretch ACKs" that
cover more than the RFC-specified maximum of 2 packets. These stretch
ACKs can cause serious performance shortfalls in common congestion
control algorithms that were designed and tuned years ago with
receiver hosts that were not using LRO or GRO, and were instead
politely ACKing every other packet.
This patch series fixes Reno and CUBIC to handle stretch ACKs.
This patch prepares for the upcoming stretch ACK bug fix patches. It
adds an "acked" parameter to tcp_cong_avoid_ai() to allow for future
fixes to tcp_cong_avoid_ai() to correctly handle stretch ACKs, and
changes all congestion control algorithms to pass in 1 for the ACKed
count. It also changes tcp_slow_start() to return the number of packet
ACK "credits" that were not processed in slow start mode, and can be
processed by the congestion control module in additive increase mode.
In future patches we will fix tcp_cong_avoid_ai() to handle stretch
ACKs, and fix Reno and CUBIC handling of stretch ACKs in slow start
and additive increase mode.
Reported-by: Eyal Perry <eyalpe@mellanox.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The smp_unregister() function needs to be called every time the
controller is powered down. There are multiple entry points when
this can happen. One is "hciconfig hci0 reset" which will throw
a WARN_ON when LE support has been enabled.
[ 78.564620] WARNING: CPU: 0 PID: 148 at net/bluetooth/smp.c:3075 smp_register+0xf1/0x170()
[ 78.564622] Modules linked in:
[ 78.564628] CPU: 0 PID: 148 Comm: kworker/u3:1 Not tainted 3.19.0-rc4-devel+ #404
[ 78.564629] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS
[ 78.564635] Workqueue: hci0 hci_rx_work
[ 78.564638] ffffffff81b4a7a2 ffff88001cb2fb38 ffffffff8161d881 0000000080000000
[ 78.564642] 0000000000000000 ffff88001cb2fb78 ffffffff8103b870 696e55206e6f6f6d
[ 78.564645] ffff88001d965000 0000000000000000 0000000000000000 ffff88001d965000
[ 78.564648] Call Trace:
[ 78.564655] [<ffffffff8161d881>] dump_stack+0x4f/0x7b
[ 78.564662] [<ffffffff8103b870>] warn_slowpath_common+0x80/0xc0
[ 78.564667] [<ffffffff81544b00>] ? add_uuid+0x1f0/0x1f0
[ 78.564671] [<ffffffff8103b955>] warn_slowpath_null+0x15/0x20
[ 78.564674] [<ffffffff81562d81>] smp_register+0xf1/0x170
[ 78.564680] [<ffffffff81081236>] ? lock_timer_base.isra.30+0x26/0x50
[ 78.564683] [<ffffffff81544bf0>] powered_complete+0xf0/0x120
[ 78.564688] [<ffffffff8152e622>] hci_req_cmd_complete+0x82/0x260
[ 78.564692] [<ffffffff8153554f>] hci_cmd_complete_evt+0x6cf/0x2e20
[ 78.564697] [<ffffffff81623e43>] ? _raw_spin_unlock_irqrestore+0x13/0x30
[ 78.564701] [<ffffffff8106b0af>] ? __wake_up_sync_key+0x4f/0x60
[ 78.564705] [<ffffffff8153a2ab>] hci_event_packet+0xbcb/0x2e70
[ 78.564709] [<ffffffff814094d3>] ? skb_release_all+0x23/0x30
[ 78.564711] [<ffffffff81409529>] ? kfree_skb+0x29/0x40
[ 78.564715] [<ffffffff815296c8>] hci_rx_work+0x1c8/0x3f0
[ 78.564719] [<ffffffff8105bd91>] ? get_parent_ip+0x11/0x50
[ 78.564722] [<ffffffff8105be25>] ? preempt_count_add+0x55/0xb0
[ 78.564727] [<ffffffff8104f65f>] process_one_work+0x12f/0x360
[ 78.564731] [<ffffffff8104ff9b>] worker_thread+0x6b/0x4b0
[ 78.564735] [<ffffffff8104ff30>] ? cancel_delayed_work_sync+0x10/0x10
[ 78.564738] [<ffffffff810542fa>] kthread+0xea/0x100
[ 78.564742] [<ffffffff81620000>] ? __schedule+0x3e0/0x980
[ 78.564745] [<ffffffff81054210>] ? kthread_create_on_node+0x180/0x180
[ 78.564749] [<ffffffff816246ec>] ret_from_fork+0x7c/0xb0
[ 78.564752] [<ffffffff81054210>] ? kthread_create_on_node+0x180/0x180
[ 78.564755] ---[ end trace 8b0d943af76d3736 ]---
This warning is not critical and has only been placed in the code to
actually catch this exact situation. To avoid triggering it move
the smp_unregister() into hci_dev_do_close() which will now also
take care of remove the SMP channel. It is safe to call this function
since it only remove the channel if it has been previously registered.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
