| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Currently, the testbus configuration is written and completed with an mb().
mb() ensures that the write completes, but completion doesn't mean that it
isn't stored in a buffer somewhere. The recommendation for ensuring this
bit has taken effect on the device is to perform a read back to force it to
make it all the way to the device. This is documented in device-io.rst and
a talk by Will Deacon on this can be seen over here:
https://youtu.be/i6DayghhA8Q?si=MiyxB5cKJXSaoc01&t=1678
But, there's really no reason to even ensure completion before
continuing. The only requirement here is that this write is ordered to this
endpoint (which readl()/writel() guarantees already). For that reason the
mb() can be dropped altogether without anything forcing completion.
Fixes: 9c46b8676271 ("scsi: ufs-qcom: dump additional testbus registers")
Signed-off-by: Andrew Halaney <ahalaney@redhat.com>
Link: https://lore.kernel.org/r/20240329-ufs-reset-ensure-effect-before-delay-v5-3-181252004586@redhat.com
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Currently after writing to REG_UFS_SYS1CLK_1US a mb() is used to ensure
that write has gone through to the device.
mb() ensures that the write completes, but completion doesn't mean that it
isn't stored in a buffer somewhere. The recommendation for ensuring this
bit has taken effect on the device is to perform a read back to force it to
make it all the way to the device. This is documented in device-io.rst and
a talk by Will Deacon on this can be seen over here:
https://youtu.be/i6DayghhA8Q?si=MiyxB5cKJXSaoc01&t=1678
Let's do that to ensure the bit hits the device. Because the mb()'s purpose
wasn't to add extra ordering (on top of the ordering guaranteed by
writel()/readl()), it can safely be removed.
Fixes: f06fcc7155dc ("scsi: ufs-qcom: add QUniPro hardware support and power optimizations")
Reviewed-by: Can Guo <quic_cang@quicinc.com>
Signed-off-by: Andrew Halaney <ahalaney@redhat.com>
Link: https://lore.kernel.org/r/20240329-ufs-reset-ensure-effect-before-delay-v5-2-181252004586@redhat.com
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Currently, the reset bit for the UFS provided reset controller (used by its
phy) is written to, and then a mb() happens to try and ensure that hit the
device. Immediately afterwards a usleep_range() occurs.
mb() ensures that the write completes, but completion doesn't mean that it
isn't stored in a buffer somewhere. The recommendation for ensuring this
bit has taken effect on the device is to perform a read back to force it to
make it all the way to the device. This is documented in device-io.rst and
a talk by Will Deacon on this can be seen over here:
https://youtu.be/i6DayghhA8Q?si=MiyxB5cKJXSaoc01&t=1678
Let's do that to ensure the bit hits the device. By doing so and
guaranteeing the ordering against the immediately following usleep_range(),
the mb() can safely be removed.
Fixes: 81c0fc51b7a7 ("ufs-qcom: add support for Qualcomm Technologies Inc platforms")
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Can Guo <quic_cang@quicinc.com>
Signed-off-by: Andrew Halaney <ahalaney@redhat.com>
Link: https://lore.kernel.org/r/20240329-ufs-reset-ensure-effect-before-delay-v5-1-181252004586@redhat.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Core in scsi_register_driver() already sets the .owner, so driver does not
need to.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240328-b4-module-owner-scsi-v1-6-c86cb4f6e91c@linaro.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Core in scsi_register_driver() already sets the .owner, so driver does not
need to.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240328-b4-module-owner-scsi-v1-5-c86cb4f6e91c@linaro.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Core in scsi_register_driver() already sets the .owner, so driver does not
need to.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240328-b4-module-owner-scsi-v1-4-c86cb4f6e91c@linaro.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Core in scsi_register_driver() already sets the .owner, so driver does not
need to.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240328-b4-module-owner-scsi-v1-3-c86cb4f6e91c@linaro.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Core in scsi_register_driver() already sets the .owner, so driver does not
need to.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240328-b4-module-owner-scsi-v1-2-c86cb4f6e91c@linaro.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Modules registering driver with scsi_driver_register() might forget to set
.owner field. The field is used by some of other kernel parts for
reference counting (try_module_get()), so it is expected that drivers will
set it.
Solve the problem by moving this task away from the drivers to the core
scsi code, just like we did for platform_driver in commit 9447057eaff8
("platform_device: use a macro instead of platform_driver_register").
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240328-b4-module-owner-scsi-v1-1-c86cb4f6e91c@linaro.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
PCI core in pci_register_driver() already sets the .owner, so driver does
not need to.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240327174921.519830-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
PCI core in pci_register_driver() already sets the .owner, so driver does
not need to.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240327174921.519830-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Commit b4d3ddd2df75 ("scsi: libsas: Define NCQ Priority sysfs attributes
for SATA devices") introduced support for ATA NCQ priority control for ATA
devices managed by libsas. This commit introduces the ncq_prio_supported
and ncq_prio_enable sysfs device attributes to discover and control the use
of this features, similarly to libata. However, libata publicly declares
these device attributes and export them for use in ATA low level
drivers. This leads to a compilation error when libsas and libata are
built-in due to the double definition:
ld: drivers/ata/libata-sata.o:/home/Linux/scsi/drivers/ata/libata-sata.c:900:
multiple definition of `dev_attr_ncq_prio_supported';
drivers/scsi/libsas/sas_ata.o:/home/Linux/scsi/drivers/scsi/libsas/sas_ata.c:984:
first defined here
ld: drivers/ata/libata-sata.o:/home/Linux/scsi/drivers/ata/libata-sata.c:1026:
multiple definition of `dev_attr_ncq_prio_enable';
drivers/scsi/libsas/sas_ata.o:/home/Linux/scsi/drivers/scsi/libsas/sas_ata.c:1022:
first defined here
Resolve this problem by directly declaring the libsas attributes instead of
using the DEVICE_ATTR() macro. And for good measure, the device attribute
variables are also renamed.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Fixes: b4d3ddd2df75 ("scsi: libsas: Define NCQ Priority sysfs attributes for SATA devices")
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Link: https://lore.kernel.org/r/20240327020122.439424-1-dlemoal@kernel.org
Reviewed-by: John Garry <john.g.garry@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
MediaTek platforms"
Peter Wang <peter.wang@mediatek.com> says:
This series fixes some defects and provide features in MediaTek UFS
drivers.
Link: https://lore.kernel.org/r/20240315083448.7185-1-peter.wang@mediatek.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Add mtcmos control function and config.
Signed-off-by: Alice Chao <alice.chao@mediatek.com>
Reviewed-by: Peter Wang <peter.wang@mediatek.com>
Acked-by: Chun-Hung Wu <Chun-Hung.Wu@mediatek.com>
Signed-off-by: Peter Wang <peter.wang@mediatek.com>
Link: https://lore.kernel.org/r/20240315083448.7185-8-peter.wang@mediatek.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Reset mphy when resetting host. Backup mphy setting after mphy reset
control get. Restore mphy setting after mphy reset.
Acked-by: Chun-Hung Wu <Chun-Hung.Wu@mediatek.com>
Signed-off-by: Peter Wang <peter.wang@mediatek.com>
Link: https://lore.kernel.org/r/20240315083448.7185-7-peter.wang@mediatek.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Mediatek host power includes two parts:
1. ufshci power, which is the main power of ufs host controller.
2. ufshci crypto sram power, which is the power of ufs crypto engine.
The host power control is actually controlling crypto sram power. Rename
it.
Signed-off-by: Po-Wen Kao <powen.kao@mediatek.com>
Acked-by: Chun-Hung Wu <Chun-Hung.Wu@mediatek.com>
Reviewed-by: Peter Wang <peter.wang@mediatek.com>
Signed-off-by: Peter Wang <peter.wang@mediatek.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Link: https://lore.kernel.org/r/20240315083448.7185-6-peter.wang@mediatek.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Move sip command and associated define to a new sip header file.
Signed-off-by: Po-Wen Kao <powen.kao@mediatek.com>
Acked-by: Chun-Hung Wu <Chun-Hung.Wu@mediatek.com>
Reviewed-by: Peter Wang <peter.wang@mediatek.com>
Signed-off-by: Peter Wang <peter.wang@mediatek.com>
Link: https://lore.kernel.org/r/20240315083448.7185-5-peter.wang@mediatek.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Add new mediatek host cap UFS_MTK_CAP_DISABLE_MCQ to allow disabling MCQ
feature by assigning dts boolean property "mediatek,ufs-disable-mcq".
Signed-off-by: Po-Wen Kao <powen.kao@mediatek.com>
Reviewed-by: Peter Wang <peter.wang@mediatek.com>
Acked-by: Chun-Hung Wu <Chun-Hung.Wu@mediatek.com>
Signed-off-by: Peter Wang <peter.wang@mediatek.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Link: https://lore.kernel.org/r/20240315083448.7185-4-peter.wang@mediatek.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Fix Mediatek TX skew issue by checking dts setting and vendor/model. Then
set PA_TACTIVATE to 8.
Signed-off-by: Peter Wang <peter.wang@mediatek.com>
Acked-by: Chun-Hung Wu <Chun-Hung.Wu@mediatek.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Link: https://lore.kernel.org/r/20240315083448.7185-3-peter.wang@mediatek.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
VSX (the upper layer of VCCQ/VCCQ2) should:
1. Always set to hpm mode if ufs device is active.
2. Enter lpm mode only if ufs device is not active.
VCCQX should:
1. Keep hpm mode if vccq and vccq2 not set in dts.
2. Keep hpm mode if vcc not set in dts keep vcc always on.
3. Keep hpm if broken vcc keep vcc always on and not allow vccq lpm.
4. Except upper case, can enter lpm mode if ufs device is not active.
Acked-by: Chun-Hung Wu <Chun-Hung.Wu@mediatek.com>
Signed-off-by: Peter Wang <peter.wang@mediatek.com>
Link: https://lore.kernel.org/r/20240315083448.7185-2-peter.wang@mediatek.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Ranjan Kumar <ranjan.kumar@broadcom.com> says:
Few Enhancements and minor fixes of mpi3mr driver.
Link: https://lore.kernel.org/r/20240313100746.128951-1-ranjan.kumar@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Update driver version to 8.8.1.0.50.
Signed-off-by: Ranjan Kumar <ranjan.kumar@broadcom.com>
Link: https://lore.kernel.org/r/20240313100746.128951-8-ranjan.kumar@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Update MPI Headers to revision 31.
Signed-off-by: Ranjan Kumar <ranjan.kumar@broadcom.com>
Signed-off-by: Sathya Prakash <sathya.prakash@broadcom.com>
Link: https://lore.kernel.org/r/20240313100746.128951-7-ranjan.kumar@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Update driver to include OS type in fault/reset reason code. MPI request
sent through ioctl now automatically dumped on timeout.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202403081903.q3Dq54zZ-lkp@intel.com/
Signed-off-by: Ranjan Kumar <ranjan.kumar@broadcom.com>
Signed-off-by: Sathya Prakash <sathya.prakash@broadcom.com>
Link: https://lore.kernel.org/r/20240313100746.128951-6-ranjan.kumar@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Modify driver to set the Write Same Divert Capability bit in the IOCInit
message for the firmware to know that the driver is capable of diverting
certain Write Same commands as defined by the MPI specification.
Signed-off-by: Ranjan Kumar <ranjan.kumar@broadcom.com>
Signed-off-by: Sathya Prakash <sathya.prakash@broadcom.com>
Link: https://lore.kernel.org/r/20240313100746.128951-5-ranjan.kumar@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The driver uses a controller-wide flag to block ioctls when a controller
reset is in progress. This flag is set before controller reset is initiated
and cleared after the reset has completed.
Make the driver clear the controller-wide block ioctls flag after a
controller reset fails and the controller is marked unrecoverable.
Signed-off-by: Ranjan Kumar <ranjan.kumar@broadcom.com>
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Link: https://lore.kernel.org/r/20240313100746.128951-4-ranjan.kumar@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The 'flags' variable inside an MPI request is a bitfield and should
consequently be updated using a bitwise OR operation.
Signed-off-by: Ranjan Kumar <ranjan.kumar@broadcom.com>
Signed-off-by: Sathya Prakash <sathya.prakash@broadcom.com>
Link: https://lore.kernel.org/r/20240313100746.128951-3-ranjan.kumar@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The driver did not remove the virtual disk that was exposed as hidden and
offline after the controller was reset.
Drive is removed from OS when firmware sends "device added" event with
hidden bit set or access status indicating inability to accept I/Os.
Signed-off-by: Ranjan Kumar <ranjan.kumar@broadcom.com>
Signed-off-by: Sathya Prakash <sathya.prakash@broadcom.com>
Link: https://lore.kernel.org/r/20240313100746.128951-2-ranjan.kumar@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Avri Altman <avri.altman@wdc.com> says:
Device management commands are constructed for query commands that are
being issued by the driver, but also for raw device management
commands originated by the bsg module, and recently, by the advanced
rpmb handler. Thus, the same code fragments, e.g. locking, composing
the command, composing the upiu etc., appear over and over. Remove
those duplications. Theoretically, there should be no functional
change.
Link: https://lore.kernel.org/r/20240309081104.5006-1-avri.altman@wdc.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Move some code fragments into ufshcd_prepare_req_desc_hdr() so it can be
used throughout.
Signed-off-by: Avri Altman <avri.altman@wdc.com>
Link: https://lore.kernel.org/r/20240309081104.5006-5-avri.altman@wdc.com
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Move out some of the dev_cmd initializations so they can be used elsewhere.
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Avri Altman <avri.altman@wdc.com>
Link: https://lore.kernel.org/r/20240309081104.5006-4-avri.altman@wdc.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Move out the actual command issue from exec_dev_cmd it can be used
elsewhere. While at it, remove a redundant "lrbp->cmd = NULL" assignment.
Also, the device management commands that are originated from the
ufs-bsg code path, are being traced now, which wasn't the case before.
Signed-off-by: Avri Altman <avri.altman@wdc.com>
Link: https://lore.kernel.org/r/20240309081104.5006-3-avri.altman@wdc.com
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Group those 3 calls that repeat for every device management command into
lock and unlock handlers.
Reviewed-by: Bean Huo <beanhuo@micron.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Avri Altman <avri.altman@wdc.com>
Link: https://lore.kernel.org/r/20240309081104.5006-2-avri.altman@wdc.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
John Garry <john.g.garry@oracle.com> says:
There is much duplication in the scsi_host_template structure for the
drivers which use libsas.
Similar to how a standard template is used in libata with
__ATA_BASE_SHT, create a standard template in LIBSAS_SHT_BASE.
Link: https://lore.kernel.org/r/20240308114339.1340549-1-john.g.garry@oracle.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Use standard template for scsi_host_template structure to reduce
duplication.
Reviewed-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: John Garry <john.g.garry@oracle.com>
Link: https://lore.kernel.org/r/20240308114339.1340549-7-john.g.garry@oracle.com
Reviewed-by: Igor Pylypiv <ipylypiv@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Use standard template for scsi_host_template structure to reduce
duplication.
Signed-off-by: John Garry <john.g.garry@oracle.com>
Link: https://lore.kernel.org/r/20240308114339.1340549-6-john.g.garry@oracle.com
Reviewed-by: Igor Pylypiv <ipylypiv@google.com>
Reviewed-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Use standard template for scsi_host_template structure to reduce
duplication.
Reviewed-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: John Garry <john.g.garry@oracle.com>
Link: https://lore.kernel.org/r/20240308114339.1340549-5-john.g.garry@oracle.com
Reviewed-by: Igor Pylypiv <ipylypiv@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Use standard template for scsi_host_template structure to reduce
duplication.
Reviewed-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: John Garry <john.g.garry@oracle.com>
Link: https://lore.kernel.org/r/20240308114339.1340549-4-john.g.garry@oracle.com
Reviewed-by: Igor Pylypiv <ipylypiv@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Use standard template for scsi_host_template structure to reduce
duplication.
Signed-off-by: John Garry <john.g.garry@oracle.com>
Link: https://lore.kernel.org/r/20240308114339.1340549-3-john.g.garry@oracle.com
Reviewed-by: Igor Pylypiv <ipylypiv@google.com>
Reviewed-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
There is much duplication in the scsi_host_template structure for the
drivers which use libsas.
Similar to how a standard template is used in libata with __ATA_BASE_SHT,
create a standard template in LIBSAS_SHT_BASE.
Don't set a default for max_sectors at SCSI_DEFAULT_MAX_SECTORS, as
scsi_host_alloc() will default to this value automatically.
Even though some drivers don't set proc_name, it won't make much difference
to set as DRV_NAME.
Also add LIBSAS_SHT_BASE_NO_SLAVE_INIT for the hisi_sas drivers which have
custom .slave_alloc and .slave_configure methods.
Reviewed-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: John Garry <john.g.garry@oracle.com>
Link: https://lore.kernel.org/r/20240308114339.1340549-2-john.g.garry@oracle.com
Reviewed-by: Igor Pylypiv <ipylypiv@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Igor Pylypiv <ipylypiv@google.com> says:
This patch series adds ncq_prio_supported and ncq_prio_enable sysfs
attributes for libsas managed SATA devices. Existing libata sysfs
attributes cannot be used directly because the ata_port location is
different for libsas.
Link: https://lore.kernel.org/r/20240307214418.3812290-1-ipylypiv@google.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The added sysfs attributes group enables the configuration of NCQ Priority
feature for HBAs that rely on libsas to manage SATA devices.
Reviewed-by: John Garry <john.g.garry@oracle.com>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Jason Yan <yanaijie@huawei.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Igor Pylypiv <ipylypiv@google.com>
Link: https://lore.kernel.org/r/20240307214418.3812290-8-ipylypiv@google.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The added sysfs attributes group enables the configuration of NCQ Priority
feature for HBAs that rely on libsas to manage SATA devices.
Reviewed-by: John Garry <john.g.garry@oracle.com>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Jason Yan <yanaijie@huawei.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Igor Pylypiv <ipylypiv@google.com>
Link: https://lore.kernel.org/r/20240307214418.3812290-7-ipylypiv@google.com
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The added sysfs attributes group enables the configuration of NCQ Priority
feature for HBAs that rely on libsas to manage SATA devices.
Omitted hisi_sas_v1_hw.c because v1 HW doesn't support SATA.
Reviewed-by: John Garry <john.g.garry@oracle.com>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Jason Yan <yanaijie@huawei.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Igor Pylypiv <ipylypiv@google.com>
Link: https://lore.kernel.org/r/20240307214418.3812290-6-ipylypiv@google.com
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The added sysfs attributes group enables the configuration of NCQ Priority
feature for HBAs that rely on libsas to manage SATA devices.
Reviewed-by: John Garry <john.g.garry@oracle.com>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Jason Yan <yanaijie@huawei.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Igor Pylypiv <ipylypiv@google.com>
Link: https://lore.kernel.org/r/20240307214418.3812290-5-ipylypiv@google.com
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The added sysfs attributes group enables the configuration of NCQ Priority
feature for HBAs that rely on libsas to manage SATA devices.
Acked-by: Jack Wang <jinpu.wang@ionos.com>
Reviewed-by: John Garry <john.g.garry@oracle.com>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Jason Yan <yanaijie@huawei.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Igor Pylypiv <ipylypiv@google.com>
Link: https://lore.kernel.org/r/20240307214418.3812290-4-ipylypiv@google.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
libata sysfs attributes cannot be used for libsas-managed SATA devices
because the ata_port location is different for libsas.
Defined sysfs attributes (visible for SATA devices only):
- /sys/block/sda/device/ncq_prio_enable
- /sys/block/sda/device/ncq_prio_supported
The newly defined attributes will pass the correct ata_port to libata
helper functions.
Reviewed-by: John Garry <john.g.garry@oracle.com>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Igor Pylypiv <ipylypiv@google.com>
Link: https://lore.kernel.org/r/20240307214418.3812290-3-ipylypiv@google.com
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Export libata NCQ Priority configuration helpers to be reused for libsas
managed SATA devices.
Switched locking from spin_lock_irq() to spin_lock_irqsave(). In the
future someone might call these helper functions when interrupts are
disabled. spin_unlock_irq() could lead to a premature re-enabling of
interrupts, whereas spin_unlock_irqrestore() restores the interrupt state
to its condition prior to the spin_lock_irqsave() call.
Acked-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Jason Yan <yanaijie@huawei.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Igor Pylypiv <ipylypiv@google.com>
Link: https://lore.kernel.org/r/20240307214418.3812290-2-ipylypiv@google.com
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Justin Stitt <justinstitt@google.com> says:
This series contains multiple replacements of strncpy throughout the
scsi subsystem.
strncpy() is deprecated for use on NUL-terminated destination strings
[1] and as such we should prefer more robust and less ambiguous string
interfaces. The details of each replacement will be in their
respective patch.
Link: https://lore.kernel.org/r/20240305-strncpy-drivers-scsi-mpi3mr-mpi3mr_fw-c-v3-0-5b78a13ff984@google.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Pull in the outstanding updates from the 6.9/scsi-queue branch.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
