| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Pull vdpa/mlx5 fixes from Michael Tsirkin:
"Last minute fixes.
These all look like something we are better off having
than not ..."
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
vdpa/mlx5: Fix suspend/resume index restoration
vdpa/mlx5: Fix wrong use of bit numbers
vdpa/mlx5: Retrieve BAR address suitable any function
vdpa/mlx5: Use the correct dma device when registering memory
vdpa/mlx5: should exclude header length and fcs from mtu
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/andersson/remoteproc
Pull remoteproc fixes from Bjorn Andersson:
"This fixes an issue with firmware loading on the TI K3 PRU, fixes
compatibility with GNU binutils for the same and resolves link error
due to a 64-bit division in the Qualcomm PIL info.
It also recognizes Mathieu Poirier as co-maintainer of the remoteproc
and rpmsg subsystems"
* tag 'rproc-v5.12-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/andersson/remoteproc:
remoteproc: pru: Fix firmware loading crashes on K3 SoCs
remoteproc: pru: Fix loading of GNU Binutils ELF
MAINTAINERS: Add co-maintainer for remoteproc/RPMSG subsystems
remoteproc: qcom: pil_info: avoid 64-bit division
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fix from Juergen Gross:
"A single fix of a 5.12 patch for the rather uncommon problem of
running as a Xen guest with a real time kernel config"
* tag 'for-linus-5.12b-rc7-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/evtchn: Change irq_info lock to raw_spinlock_t
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fix from Rafael Wysocki:
"Fix a build issue introduced by a previous fix in the ACPI processor
driver (Vitaly Kuznetsov)"
* tag 'acpi-5.12-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: processor: Fix build when CONFIG_ACPI_PROCESSOR=m
|
|
When we suspend the VM, the VDPA interface will be reset. When the VM is
resumed again, clear_virtqueues() will clear the available and used
indices resulting in hardware virqtqueue objects becoming out of sync.
We can avoid this function alltogether since qemu will clear them if
required, e.g. when the VM went through a reboot.
Moreover, since the hw available and used indices should always be
identical on query and should be restored to the same value same value
for virtqueues that complete in order, we set the single value provided
by set_vq_state(). In get_vq_state() we return the value of hardware
used index.
Fixes: b35ccebe3ef7 ("vdpa/mlx5: Restore the hardware used index after change map")
Fixes: 1a86b377aa21 ("vdpa/mlx5: Add VDPA driver for supported mlx5 devices")
Signed-off-by: Eli Cohen <elic@nvidia.com>
Link: https://lore.kernel.org/r/20210408091047.4269-6-elic@nvidia.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
|
|
VIRTIO_F_VERSION_1 is a bit number. Use BIT_ULL() with mask
conditionals.
Also, in mlx5_vdpa_is_little_endian() use BIT_ULL for consistency with
the rest of the code.
Fixes: 1a86b377aa21 ("vdpa/mlx5: Add VDPA driver for supported mlx5 devices")
Signed-off-by: Eli Cohen <elic@nvidia.com>
Link: https://lore.kernel.org/r/20210408091047.4269-5-elic@nvidia.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
|
|
struct mlx5_core_dev has a bar_addr field that contains the correct bar
address for the function regardless of whether it is pci function or sub
function. Use it.
Fixes: 1958fc2f0712 ("net/mlx5: SF, Add auxiliary device driver")
Signed-off-by: Eli Cohen <elic@nvidia.com>
Reviewed-by: Parav Pandit <parav@nvidia.com>
Link: https://lore.kernel.org/r/20210408091047.4269-4-elic@nvidia.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
|
|
In cases where the vdpa instance uses a SF (sub function), the DMA
device is the parent device. Use a function to retrieve the correct DMA
device.
Fixes: 1958fc2f0712 ("net/mlx5: SF, Add auxiliary device driver")
Signed-off-by: Eli Cohen <elic@nvidia.com>
Reviewed-by: Parav Pandit <parav@nvidia.com>
Link: https://lore.kernel.org/r/20210408091047.4269-3-elic@nvidia.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
|
|
When feature VIRTIO_NET_F_MTU is negotiated on mlx5_vdpa,
22 extra bytes worth of MTU length is shown in guest.
This is because the mlx5_query_port_max_mtu API returns
the "hardware" MTU value, which does not just contain the
Ethernet payload, but includes extra lengths starting
from the Ethernet header up to the FCS altogether.
Fix the MTU so packets won't get dropped silently.
Fixes: 1a86b377aa21 ("vdpa/mlx5: Add VDPA driver for supported mlx5 devices")
Signed-off-by: Si-Wei Liu <si-wei.liu@oracle.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Acked-by: Eli Cohen <elic@nvidia.com>
Link: https://lore.kernel.org/r/20210408091047.4269-2-elic@nvidia.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
drivers/usb/core/hub.c: usb_new_device() contains the following:
/* By default, forbid autosuspend for all devices. It will be
* allowed for hubs during binding.
*/
usb_disable_autosuspend(udev);
So for anything which is not a hub, such as btusb devices, autosuspend is
disabled by default and we must call usb_enable_autosuspend(udev) to
enable it.
This means that the "Fix the autosuspend enable and disable" commit,
which drops the usb_enable_autosuspend() call when the enable_autosuspend
module option is true, is completely wrong, revert it.
This reverts commit 7bd9fb058d77213130e4b3e594115c028b708e7e.
Cc: Hui Wang <hui.wang@canonical.com>
Fixes: 7bd9fb058d77 ("Bluetooth: btusb: Fix the autosuspend enable and disable")
Acked-by: Hui Wang <hui.wang@canonical.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
TIOCSSERIAL is a horrid, underspecified, legacy interface which for most
serial devices is only useful for setting the close_delay and
closing_wait parameters.
The xmit_fifo_size parameter could be used to set the hardware transmit
fifo size of a legacy UART when it could not be detected, but the
interface is limited to eight bits and should be left unset when it is
not used.
Similarly, baud_base could be used to set the UART base clock when it
could not be detected, but might as well be left unset when it is not
known (which is the case for CDC).
Fix the cdc-acm TIOCGSERIAL implementation by dropping its custom
interpretation of the unused xmit_fifo_size and baud_base fields, which
overflowed the former with the URB buffer size and set the latter to the
current line speed. Also return the port line number, which is the only
other value used besides the close parameters.
Note that the current line speed can still be retrieved through the
standard termios interfaces.
Fixes: 18c75720e667 ("USB: allow users to run setserial with cdc-acm")
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210408131602.27956-4-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
TIOCSSERIAL is a horrid, underspecified, legacy interface which for most
serial devices is only useful for setting the close_delay and
closing_wait parameters.
A non-privileged user has only ever been able to set the since long
deprecated ASYNC_SPD flags and trying to change any other *supported*
feature should result in -EPERM being returned. Setting the current
values for any supported features should return success.
Fix the cdc-acm implementation which instead indicated that the
TIOCSSERIAL ioctl was not even implemented when a non-privileged user
set the current values.
Fixes: ba2d8ce9db0a ("cdc-acm: implement TIOCSSERIAL to avoid blocking close(2)")
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210408131602.27956-3-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit b401f8c4f492cbf74f3f59c9141e5be3071071bb.
The offending commit claimed that trying to set the values reported back
by TIOCGSERIAL as a regular user could result in an -EPERM error when HZ
is 250, but that was never the case.
With HZ=250, the default 0.5 second value of close_delay is converted to
125 jiffies when set and is converted back to 50 centiseconds by
TIOCGSERIAL as expected (not 12 cs as was claimed, even if that was the
case before an earlier fix).
Comparing the internal current and new jiffies values is just fine to
determine if the value is about to change so drop the bogus workaround
(which was also backported to stable).
For completeness: With different default values for these parameters or
with a HZ value not divisible by two, the lack of rounding when setting
the default values in tty_port_init() could result in an -EPERM being
returned, but this is hardly something we need to worry about.
Cc: Anthony Mallet <anthony.mallet@laas.fr>
Cc: stable@vger.kernel.org
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210408131602.27956-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
connector fwnode
Add a displayport altmode fwnode to the usb-connector fwnode,
devices which use this driver support display-port altmode through
the PI3USB30532 USB switch, this enables support for this.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210409134033.105834-4-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add support for altmodes described in the usb-connector fwnode
associated with the Type-C controller by calling the new
typec_port_register_altmodes_from_fwnode() helper for this.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210409134033.105834-3-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This can be used by Type-C controller drivers which use a standard
usb-connector fwnode, with altmodes sub-node, to describe the available
altmodes.
Note there are is no devicetree bindings documentation for the altmodes
node, this is deliberate. ATM the fwnodes used to register the altmodes
are only used internally to pass platform info from a drivers/platform/x86
driver to the type-c subsystem.
When a devicetree user of this functionally comes up and the dt-bindings
have been hashed out the internal use can be adjusted to match the
dt-bindings.
Currently the typec_port_register_altmodes() function expects
an "altmodes" child fwnode on port->dev with this "altmodes" fwnode having
child fwnodes itself with each child containing 2 integer properties:
1. A "svid" property, which sets the id of the altmode, e.g. displayport
altmode has a svid of 0xff01.
2. A "vdo" property, typically used as a bitmask describing the
capabilities of the altmode, the bits in the vdo are specified in the
specification of the altmode.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210409134033.105834-2-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
usb_role_switch_find_by_fwnode() returns a reference to the role-switch
which must be put by calling usb_role_switch_put().
usb_role_switch_put() calls module_put(sw->dev.parent->driver->owner),
add a matching try_module_get() to usb_role_switch_find_by_fwnode(),
making it behave the same as the other usb_role_switch functions
which return a reference.
This avoids a WARN_ON being hit at kernel/module.c:1158 due to the
module-refcount going below 0.
Fixes: c6919d5e0cd1 ("usb: roles: Add usb_role_switch_find_by_fwnode()")
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210409124136.65591-1-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The clocks are configured by devm_clk_bulk_get_all() in this driver. In
case of any error the clocks freeing will be handled automatically.
There is no need to explicitly free the clocks. Fix the same.
Fixes: 84770f028fab ("usb: dwc3: Add driver for Xilinx platforms")
Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Link: https://lore.kernel.org/r/1617904448-74611-3-git-send-email-manish.narani@xilinx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The kernel-doc run gave a warning for Xilinx DWC3 driver:
drivers/usb/dwc3/dwc3-xilinx.c:27: warning: expecting prototype for
dwc3(). Prototype was for XLNX_USB_PHY_RST_EN() instead
Basically it was due to an extra '*' in line:2. This patch fixes the same.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Link: https://lore.kernel.org/r/1617904448-74611-2-git-send-email-manish.narani@xilinx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The old document for usbip protocol is misleading and hard to read:
* Some fields in header are incorrect
* Explanation of some fields are unclear or even wrong
* Padding of header (namely all headers have the same length) is
not explicitly pointed out, which is crucial for stream protocol
like TCP
Major changes:
* Document the correct field as described in the codebase.
* Document the padding in usbip headers. This is crucial for TCP
stream hence these padding should be explicitly point out.
In code these padding are implemented by a union of all headers.
* Fix two FIXME related to usbip unlink and Document the behavior
of unlink in different situation.
* Clarify some field with more accurate explanation, like those
fields associated with URB. Some constraints are extracted from
code.
* Delete specific transfer_flag doc in usbip as it should be
documented by the URB doc in Documentation/driver-api/usb/URB.rst
* Add data captured from wire as example
Version change:
From "PRELIMINARY DRAFT, MAY CONTAIN MISTAKES, 28 Jun 2011"
To "Version 1, 31 Mar 2021"
Co-developed-by: Alexandre Demers <alexandre.f.demers@gmail.com>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Hongren Zheng <i@zenithal.me>
Link: https://lore.kernel.org/r/YGNZHfmAbHO6fyAr@Sun
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
pm_runtime_get_sync will increment pm usage counter even it failed.
thus a pairing decrement is needed.
Fix it by replacing it with pm_runtime_resume_and_get to keep usage
counter balanced.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Bixuan Cui <cuibixuan@huawei.com>
Link: https://lore.kernel.org/r/20210408130831.56239-1-cuibixuan@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
pm_runtime_get_sync will increment pm usage counter even it failed.
thus a pairing decrement is needed.
Fix it by replacing it with pm_runtime_resume_and_get to keep usage
counter balanced.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Bixuan Cui <cuibixuan@huawei.com>
Link: https://lore.kernel.org/r/20210408091836.55227-1-cuibixuan@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This driver's remove path calls cancel_delayed_work(). However, that
function does not wait until the work function finishes. This means
that the callback function may still be running after the driver's
remove function has finished, which would result in a use-after-free.
Fix by calling cancel_delayed_work_sync(), which ensures that
the work is properly cancelled, no longer running, and unable
to re-schedule itself.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20210407092947.3271507-1-yangyingliang@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
mutex lock can be initialized automatically with DEFINE_MUTEX()
rather than explicitly calling mutex_init().
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Link: https://lore.kernel.org/r/20210405101434.14878-1-zhengyongjun3@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
platform_get_resource
The call to platform_get_resource can potentially return a NULL pointer
on failure, so add this check and return -EINVAL if it fails.
Fixes: c41442474a26 ("usb: gadget: R8A66597 peripheral controller support.")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Addresses-Coverity: ("Dereference null return")
Link: https://lore.kernel.org/r/20210406184510.433497-1-colin.king@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch adds the necessary PCI ID for Intel Alder Lake-M
devices.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20210408083144.69350-1-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The connectors may be registered after the ports, so the
"connector" links need to be created for the ports also when
ever a new connector gets registered.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20210407065555.88110-5-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Introducing usb_for_each_port(). It works the same way as
usb_for_each_dev(), but instead of going through every USB
device in the system, it walks through the USB ports in the
system.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20210407065555.88110-4-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Creating link to the USB Type-C connector for every new port
that is added when possible.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20210407065555.88110-3-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Adding functions that can be used to link/unlink ports -
USB ports, TBT3/USB4 ports, DisplayPorts and so on - to
the USB Type-C connectors they are attached to inside a
system. The symlink that is created for the port device is
named "connector".
Initially only ACPI is supported. ACPI port object shares
the _PLD (Physical Location of Device) with the USB Type-C
connector that it's attached to.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20210407065555.88110-2-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
nr_empty_pop_pages is used to guarantee that there are some free
populated pages to satisfy atomic allocations. Accounted and
non-accounted allocations are using separate sets of chunks,
so both need to have a surplus of empty pages.
This commit makes pcpu_nr_empty_pop_pages and the corresponding logic
per chunk type.
[Dennis]
This issue came up as I was reviewing [1] and realized I missed this.
Simultaneously, it was reported btrfs was seeing failed atomic
allocations in fsstress tests [2] and [3].
[1] https://lore.kernel.org/linux-mm/20210324190626.564297-1-guro@fb.com/
[2] https://lore.kernel.org/linux-mm/20210401185158.3275.409509F4@e16-tech.com/
[3] https://lore.kernel.org/linux-mm/CAL3q7H5RNBjCi708GH7jnczAOe0BLnacT9C+OBgA-Dx9jhB6SQ@mail.gmail.com/
Fixes: 3c7be18ac9a0 ("mm: memcg/percpu: account percpu memory to memory cgroups")
Cc: stable@vger.kernel.org # 5.9+
Signed-off-by: Roman Gushchin <guro@fb.com>
Tested-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Dennis Zhou <dennis@kernel.org>
|
|
power_supply_changed needs to be called to notify clients
after the partner accepts the requested values for the pps
case.
Also, remove the redundant power_supply_changed at the end
of the tcpm_reset_port as power_supply_changed is already
called right after usb_type is changed.
Fixes: f2a8aa053c176 ("typec: tcpm: Represent source supply through power_supply")
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20210407200723.1914388-3-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
tcpm_pd_select_pps_apdo overwrites port->pps_data.min_volt,
port->pps_data.max_volt, port->pps_data.max_curr even before
port partner accepts the requests. This leaves incorrect values
in current_limit and supply_voltage that get exported by
"tcpm-source-psy-". Solving this problem by caching the request
values in req_min_volt, req_max_volt, req_max_curr, req_out_volt,
req_op_curr. min_volt, max_volt, max_curr gets updated once the
partner accepts the request. current_limit, supply_voltage gets updated
once local port's tcpm enters SNK_TRANSITION_SINK when the accepted
current_limit and supply_voltage is enforced.
Fixes: f2a8aa053c176 ("typec: tcpm: Represent source supply through power_supply")
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20210407200723.1914388-2-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
tcpm_pd_build_request overwrites current_limit and supply_voltage
even before port partner accepts the requests. This leaves stale
values in current_limit and supply_voltage that get exported by
"tcpm-source-psy-". Solving this problem by caching the request
values of current limit/supply voltage in req_current_limit
and req_supply_voltage. current_limit/supply_voltage gets updated
once the port partner accepts the request.
Fixes: f2a8aa053c176 ("typec: tcpm: Represent source supply through power_supply")
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20210407200723.1914388-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When dwc2 core is in partial power down mode
loading driver again causes driver fail. Because in
that mode registers are not accessible.
Added a flow of exiting the partial power down mode
to avoid the driver reload failure.
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210408094615.8AE35A0094@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fixes the implementation of exiting from partial power down
power saving mode when PC is resumed.
Added port connection status checking which prevents exiting from
Partial Power Down mode from _dwc2_hcd_resume() if not in Partial
Power Down mode.
Rearranged the implementation to get rid of many "if"
statements.
NOTE: Switch case statement is used for hibernation partial
power down and clock gating mode determination. In this patch
only Partial Power Down is implemented the Hibernation and
clock gating implementations are planned to be added.
Fixes: 6f6d70597c15 ("usb: dwc2: bus suspend/resume for hosts with DWC2_POWER_DOWN_PARAM_NONE")
Cc: <stable@vger.kernel.org>
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210408094607.1A9BAA0094@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
With current implementation the port power is being disabled,
which is not required by the programming guide. Also, if there
is a system which works only in "DWC2_POWER_DOWN_PARAM_NONE"
(clock gating) mode the current implementation does not set
Gate hclk bit in pcgctl register.
Rearranges and updates the implementation of entering to partial
power down power saving mode when PC is suspended to get
rid of many "if" statements and removes disabling of port power.
NOTE: Switch case statement is used for hibernation partial
power down and clock gating mode determination. In this patch
only Partial Power Down is implemented the Hibernation and
clock gating implementations are planned to be added.
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210408094559.33541A022E@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
According to programming guide in host mode, port
power must be turned on in session request
interrupt handlers.
Fixes: 21795c826a45 ("usb: dwc2: exit hibernation on session request")
Cc: <stable@vger.kernel.org>
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210408094550.75484A0094@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When core is in partial power down state and an external
hub is connected, upper layer sends URB enqueue request,
which results in port reset issue.
Added exit from partial power down state to avoid port
reset issue and process upper layer request correctly.
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210408094542.685BAA0094@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Before changing to connector B exiting from Partial
Power Down is required.
- Added exiting from Partial Power Down mode when
connector ID status changes to "connId B".
Because if connector ID status changed to B connector
while core was in partial power down mode, HANG would
accrue from a soft reset.
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210408094534.4AA7AA022E@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Adds Partial Power Down exiting flow when set port feature
reset is received in suspended state.
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210408094526.4DD7AA022E@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Added flow of exiting Partial Power Down in
"dwc2_port_resume()" function when core receives resume.
NOTE: Switch case statement is used for hibernation partial
power down and clock gating mode determination. In this patch
only Partial Power Down is implemented the Hibernation and
clock gating implementations are planned to be added.
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210408094518.6DA1DA022E@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Adds flow of entering Partial Power Down in
"dwc2_port_suspend()" function when core receives suspend.
NOTE: Switch case statement is used for hibernation partial
power down and clock gating mode determination. In this patch
only Partial Power Down is implemented the Hibernation and
clock gating implementations are planned to be added.
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210408094510.6C4E9A022E@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Earlier "dwc2_port_suspend()" and "dwc2_port_resume()" functions
were implemented without proper description and host or device mode
difference.
- Added "dwc2_port_suspend" and "dwc2_port_resume" functions to
"core.h" header file.
- Updated function description in documentation.
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210408094502.61D18A0232@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
According to programming guide added host partial power
down exit flow in wakeup detected interrupt handler.
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210408094454.5BBCBA0094@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
These are wrapper functions which are calling device or host
enter/exit partial power down functions.
This change is done because we need to separate device and
host partial power down functions as the programming flow
has a lot of difference between host and device. With this
update during partial power down exit driver relies on
backup value of "GOTGCTL_CURMODE_HOST" to determine the
mode of core before entering to PPD.
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210408094446.6491BA022E@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
For host mode Partial Power Down entering and exiting
separate functions are needed to implement the logic.
Earlier the logic was implemented in one function. Which was
confusing the readability. Also both host and device implementations
were in the same function.
- Added host partial power down functions which must be called
by dwc2_enter_partial_power_down()/dwc2_exit_partial_power_down()
functions.
Added function names:
dwc2_host_enter_partial_power_down()
dwc2_host_exit_partial_power_down()
NOTE: There is a checkpatch "CHECK" warning on "udelay(100)".
The delay is needed to properly exit gadget Partial Power Down
A delay less than 100 doesn't work.
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210408094438.56CFBA022E@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
For device mode Partial Power Down entering and exiting
separate functions are needed to implement the logic.
Earlier the logic was implemented in one function. Which was
confusing the readability. Also both host and device implementations
were in the same function.
- Added device partial power down functions which must be called
by dwc2_enter_partial_power_down()/dwc2_exit_partial_power_down()
functions.
- Added "in_ppd" flag in "dwc2_hsotg" struct to indicate the
core state after entering into partial power down mode.
Added function names:
dwc2_gadget_enter_partial_power_down()
dwc2_gadget_exit_partial_power_down()
NOTE: There is a checkpatch "CHECK" warning on "udelay(100)".
The delay is needed to properly exit gadget Partial Power Down
A delay less than 100 doesn't work.
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210408094430.383B9A0094@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit
334872a09198 ("x86/traps: Attempt to fixup exceptions in vDSO before signaling")
added return statements which bypass calling cond_local_irq_disable().
According to
ca4c6a9858c2 ("x86/traps: Make interrupt enable/disable symmetric in C code"),
cond_local_irq_disable() is needed because the asm return code no longer
disables interrupts. Follow the existing code as an example to use "goto
exit" instead of "return" statement.
[ bp: Massage commit message. ]
Fixes: 334872a09198 ("x86/traps: Attempt to fixup exceptions in vDSO before signaling")
Signed-off-by: Thomas Tai <thomas.tai@oracle.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Alexandre Chartre <alexandre.chartre@oracle.com>
Link: https://lkml.kernel.org/r/1617902914-83245-1-git-send-email-thomas.tai@oracle.com
|
|
With USB4 devices PCIe tunneling is optional so for device routers
without PCIe upstream adapter it does not make much sense to expose the
authorized attribute. For this reason hide it if PCIe tunneling is not
supported by the device router.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
