| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The default configuration for the interrupts on dwmac1000 have the
timestamping interrupt masked. Now that the timestamping has been
adapted to dwmac1000, enable the timestamping interrupt on these
platforms.
On dwmac1000, the external snapshot interrupt is configured through a
dedicated bit, that is set as reserved on other dwmac variants. The
timestaming interrupt is acknowledged by reading the
GMAC3_X_TIMESTAMP_STATUS register.
Make sure that this interrupt is enabled when snapshot is enabled, and
masked when disabled.
Reviewed-by: Daniel Machon <daniel.machon@microchip.com>
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20241112170658.2388529-7-maxime.chevallier@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In GMAC3_X, the timestamping configuration differs from GMAC4 in the
layout of the registers accessed to grab the number of snapshots in FIFO
as well as the register offset to grab the aux snapshot timestamp.
Introduce dedicated ops to configure timestamping on dwmac100 and
dwmac1000. The latency correction doesn't seem to exist on GMAC3, so its
corresponding operation isn't populated.
Reviewed-by: Daniel Machon <daniel.machon@microchip.com>
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20241112170658.2388529-6-maxime.chevallier@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The PTP configuration for GMAC3_X differs from the other implementations
in several ways :
- There's only one external snapshot trigger
- The snapshot configuration is done through the PTP_TCR register,
whereas the other dwmac variants have a dedicated ACR (auxiliary
control reg) for that purpose
- The layout for the PTP_TCR register also differs, as bits 24/25 are
used for the snapshot configuration. These bits are reserved on other
variants.
On GMAC3_X, we also can't discover the number of snapshot triggers
automatically.
The GMAC3_X has one PPS output, however it's configuration isn't
supported yet so report 0 n_per_out for now.
Introduce a dedicated set of ptp_clock_info ops and configuration
parameters to reflect these differences specific to GMAC3_X.
This was tested on dwmac_socfpga.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20241112170658.2388529-5-maxime.chevallier@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Some DWMAC variants such as dwmac1000 don't support discovering the
number of output pps and auxiliary snapshots. Allow these parameters to
be defined in default ptp_clock_info, and let them be updated only when
the feature discovery yielded a result.
Reviewed-by: Daniel Machon <daniel.machon@microchip.com>
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20241112170658.2388529-4-maxime.chevallier@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The auxiliary snapshot configuration was found to differ depending on
the dwmac version. To prepare supporting this, allow specifying the
ptp_clock_info ops in the hwif array
Reviewed-by: Daniel Machon <daniel.machon@microchip.com>
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20241112170658.2388529-3-maxime.chevallier@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The stmmac_ptp_clock_ops are copied into the stmmac_priv structure
before being registered to the PTP core. Some adjustments are made prior
to that, such as the number of snapshots or max adjustment parameters.
Instead of modifying the global definition, then copying into the local
private data, let's first copy then modify the local parameters.
Reviewed-by: Daniel Machon <daniel.machon@microchip.com>
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20241112170658.2388529-2-maxime.chevallier@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Matthieu Baerts says:
====================
mptcp: pm: a few more fixes
Three small fixes related to the MPTCP path-manager:
- Patch 1: correctly reflect the backup flag to the corresponding local
address entry of the userspace path-manager. A fix for v5.19.
- Patch 2: hold the PM lock when deleting an entry from the local
addresses of the userspace path-manager to avoid messing up with this
list. A fix for v5.19.
- Patch 3: use _rcu variant to iterate the in-kernel path-manager's
local addresses list, when under rcu_read_lock(). A fix for v5.17.
====================
Link: https://patch.msgid.link/20241112-net-mptcp-misc-6-12-pm-v1-0-b835580cefa8@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In mptcp_pm_create_subflow_or_signal_addr(), rcu_read_(un)lock() are
used as expected to iterate over the list of local addresses, but
list_for_each_entry() was used instead of list_for_each_entry_rcu() in
__lookup_addr(). It is important to use this variant which adds the
required READ_ONCE() (and diagnostic checks if enabled).
Because __lookup_addr() is also used in mptcp_pm_nl_set_flags() where it
is called under the pernet->lock and not rcu_read_lock(), an extra
condition is then passed to help the diagnostic checks making sure
either the associated spin lock or the RCU lock is held.
Fixes: 86e39e04482b ("mptcp: keep track of local endpoint still available for each msk")
Cc: stable@vger.kernel.org
Reviewed-by: Geliang Tang <geliang@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20241112-net-mptcp-misc-6-12-pm-v1-3-b835580cefa8@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When traversing userspace_pm_local_addr_list and deleting an entry from
it in mptcp_pm_nl_remove_doit(), msk->pm.lock should be held.
This patch holds this lock before mptcp_userspace_pm_lookup_addr_by_id()
and releases it after list_move() in mptcp_pm_nl_remove_doit().
Fixes: d9a4594edabf ("mptcp: netlink: Add MPTCP_PM_CMD_REMOVE")
Cc: stable@vger.kernel.org
Signed-off-by: Geliang Tang <tanggeliang@kylinos.cn>
Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20241112-net-mptcp-misc-6-12-pm-v1-2-b835580cefa8@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Just like in-kernel pm, when userspace pm does set_flags, it needs to send
out MP_PRIO signal, and also modify the flags of the corresponding address
entry in the local address list. This patch implements the missing logic.
Traverse all address entries on userspace_pm_local_addr_list to find the
local address entry, if bkup is true, set the flags of this entry with
FLAG_BACKUP, otherwise, clear FLAG_BACKUP.
Fixes: 892f396c8e68 ("mptcp: netlink: issue MP_PRIO signals from userspace PMs")
Cc: stable@vger.kernel.org
Signed-off-by: Geliang Tang <tanggeliang@kylinos.cn>
Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20241112-net-mptcp-misc-6-12-pm-v1-1-b835580cefa8@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
genphy_c45_ethtool_get_eee
genphy_c45_eee_is_active() populates both bitmaps only if it returns
successfully. So we can avoid the overhead of the temporary bitmaps.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/b0832102-28ab-4223-b879-91fb1fc11278@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Simplify the function.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/f9a4623b-b94c-466c-8733-62057c6d9a17@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Make a minor change to eliminate a static checker warning. The type
of s->ifc is unsigned int, so the correct format specifier should be
%u instead of %d.
Signed-off-by: Luo Yifan <luoyifan@cmss.chinamobile.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20241113011142.290474-1-luoyifan@cmss.chinamobile.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Jan Stancek says:
====================
tools: ynl: two patches to ease building with rpmbuild
I'm looking to build and package ynl for Fedora and Centos Stream users.
Default rpmbuild has couple hardening options enabled by default [1][2],
which currently prevent ynl from building.
This series contains 2 small patches to address it.
[1] https://fedoraproject.org/wiki/Changes/Harden_All_Packages
[2] https://fedoraproject.org/wiki/Changes/PythonSafePath
====================
Link: https://patch.msgid.link/cover.1731399562.git.jstancek@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Package build environments like Fedora rpmbuild introduced hardening
options (e.g. -pie -Wl,-z,now) by passing a -spec option to CFLAGS
and LDFLAGS.
ynl Makefiles currently override CFLAGS but not LDFLAGS, which leads
to a mismatch and build failure:
CC sample devlink
/usr/bin/ld: devlink.o: relocation R_X86_64_32 against symbol `ynl_devlink_family' can not be used when making a PIE object; recompile with -fPIE
/usr/bin/ld: failed to set dynamic section sizes: bad value
collect2: error: ld returned 1 exit status
Extend CFLAGS to support hardening options set by build environment.
Signed-off-by: Jan Stancek <jstancek@redhat.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Donald Hunter <donald.hunter@gmail.com>
Link: https://patch.msgid.link/265b2d5d3a6d4721a161219f081058ed47dc846a.1731399562.git.jstancek@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Python options like PYTHONSAFEPATH or -P [1] do not add script
directory to PYTHONPATH. ynl depends on this path to build and run.
[1] This option is default for Fedora rpmbuild since introduction of
https://fedoraproject.org/wiki/Changes/PythonSafePath
Signed-off-by: Jan Stancek <jstancek@redhat.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Donald Hunter <donald.hunter@gmail.com>
Link: https://patch.msgid.link/b26537cdb6e1b24435b50b2ef81d71f31c630bc1.1731399562.git.jstancek@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Kalle Valo says:
====================
wireless-next patches for v6.13
Most likely the last -next pull request for v6.13. Most changes are in
Realtek and Qualcomm drivers, otherwise not really anything
noteworthy.
Major changes:
mac80211
* EHT 1024 aggregation size for transmissions
ath12k
* switch to using wiphy_lock() and remove ar->conf_mutex
* firmware coredump collection support
* add debugfs support for a multitude of statistics
ath11k
* dt: document WCN6855 hardware inputs
ath9k
* remove include/linux/ath9k_platform.h
ath5k
* Arcadyan ARV45XX AR2417 & Gigaset SX76[23] AR241[34]A support
rtw88:
* 8821au and 8812au USB adapters support
rtw89
* thermal protection
* firmware secure boot for WiFi 6 chip
* tag 'wireless-next-2024-11-13' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (154 commits)
Revert "wifi: iwlegacy: do not skip frames with bad FCS"
wifi: mac80211: pass MBSSID config by reference
wifi: mac80211: Support EHT 1024 aggregation size in TX
net: rfkill: gpio: Add check for clk_enable()
wifi: brcmfmac: Fix oops due to NULL pointer dereference in brcmf_sdiod_sglist_rw()
wifi: Switch back to struct platform_driver::remove()
wifi: ipw2x00: libipw_rx_any(): fix bad alignment
wifi: brcmfmac: release 'root' node in all execution paths
wifi: iwlwifi: mvm: don't call power_update_mac in fast suspend
wifi: iwlwifi: s/IWL_MVM_INVALID_STA/IWL_INVALID_STA
wifi: iwlwifi: bump minimum API version in BZ/SC to 92
wifi: iwlwifi: move IWL_LMAC_*_INDEX to fw/api/context.h
wifi: iwlwifi: be less noisy if the NIC is dead in S3
wifi: iwlwifi: mvm: tell iwlmei when we finished suspending
wifi: iwlwifi: allow fast resume on ax200
wifi: iwlwifi: mvm: support new initiator and responder command version
wifi: iwlwifi: mvm: use wiphy locked debugfs for low-latency
wifi: iwlwifi: mvm: MLO scan upon channel condition degradation
wifi: iwlwifi: mvm: support new versions of the wowlan APIs
wifi: iwlwifi: mvm: allow always calling iwl_mvm_get_bss_vif()
...
====================
Link: https://patch.msgid.link/20241113172918.A8A11C4CEC3@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
eb284f4b3781 drm/nouveau/dp: Honor GSP link training retry timeouts
tried to fix a problem with panel retires, however it appears
the auxch also needs the same treatment, so add the same retry
wrapper around it.
This fixes some eDP panels after a suspend/resume cycle.
Fixes: eb284f4b3781 ("drm/nouveau/dp: Honor GSP link training retry timeouts")
Cc: stable@vger.kernel.org
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241111034126.2028401-2-airlied@gmail.com
|
|
The upper layer transfer functions expect EBUSY as a return
for when retries should be done.
Fix the AUX error translation, but also check for both errors
in a few places.
Fixes: eb284f4b3781 ("drm/nouveau/dp: Honor GSP link training retry timeouts")
Cc: stable@vger.kernel.org
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241111034126.2028401-1-airlied@gmail.com
|
|
When this code moved to non-coherent allocator the sync was put too
early for some firmwares which called the setup function, move the
sync down after the setup function.
Reported-by: Diogo Ivo <diogo.ivo@tecnico.ulisboa.pt>
Tested-by: Diogo Ivo <diogo.ivo@tecnico.ulisboa.pt>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Fixes: 9b340aeb26d5 ("nouveau/firmware: use dma non-coherent allocator")
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241114004603.3095485-1-airlied@gmail.com
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/at91/linux into soc/dt
Microchip AT91 SoC updates for v6.13
It contains:
- DT bindings update for the SAM9X7 TCB block
* tag 'at91-soc-6.13' of https://git.kernel.org/pub/scm/linux/kernel/git/at91/linux:
dt-bindings: microchip: atmel,at91rm9200-tcb: add sam9x7 compatible
Link: https://lore.kernel.org/r/20241113182050.2176500-3-claudiu.beznea@tuxon.dev
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/at91/linux into soc/dt
Microchip AT91 device tree updates for v6.13
It contains:
- device tree support for the Microchip SAM9X7 SoC and the Microchip
SAM9X75 Curiosity board
- enable power monitor support for SAM9X60-EK, SAMA5D2-ICP,
SAMA7G45 Curiosity, SAMA7G5-EK boards
- updates the uart nodes with missing properties
- device tree cleanups
* tag 'at91-dt-6.13' of https://git.kernel.org/pub/scm/linux/kernel/git/at91/linux:
ARM: dts: microchip: sam9x75_curiosity: add sam9x75 curiosity board
dt-bindings: arm: add sam9x75 curiosity board
ARM: dts: at91: sam9x7: add device tree for SoC
ARM: dts: microchip: Rename LED sub nodes name
ARM: dts: microchip: Rename the pmic node
ARM: dts: microchip: Rename the eeprom nodename
ARM: dts: microchip: sama7g5ek: Add power monitor support
ARM: dts: microchip: sama7g54_curiosity: Add power monitor support
ARM: dts: microchip: sama5d2_icp: Add power monitor support
ARM: dts: microchip: sam9x60ek: Add power monitor support
ARM: dts: microchip: Unify rng node names
ARM: dts: microchip: Add trng labels for all at91 SoCs
ARM: dts: microchip: sam9x60: Add missing property atmel,usart-mode
Link: https://lore.kernel.org/r/20241113182050.2176500-2-claudiu.beznea@tuxon.dev
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Fix spelling and other issues, such as kernel-doc reported about,
in the comments. While at it, fix some indentation issues as well.
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
Currently the PCI glue driver uses sda_hold variable name, while
the rest of the driver use sda_hold_time. This makes things harder
to grep. Use sda_hold_time variable name everywhere.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
The 'cond' parameter is not being used (always default, hence drop it
and hence make it consistent with i2c_dw_scl_lcnt().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
In the snippets like the following
if (...)
return / goto / break / continue ...;
else
...
the 'else' is redundant. Get rid of it.
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
Use temporary variable for struct device to make code neater.
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
Update the MAINTAINERS file with AMD ASF driver details.
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Acked-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
To ensure successive interrupts upon packet reception, it is necessary to
clear the remote IRR bit by writing the interrupt number to the EOI
register. The base address for this operation is provided by the BIOS and
retrieved by the driver by traversing the ASF object's namespace.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Co-developed-by: Sanket Goswami <Sanket.Goswami@amd.com>
Signed-off-by: Sanket Goswami <Sanket.Goswami@amd.com>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
Add support for handling ASF slave process events as described in the AMD
ASF databook. This involves implementing the correct programming sequence
to manage each ASF packet appropriately.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Co-developed-by: Sanket Goswami <Sanket.Goswami@amd.com>
Signed-off-by: Sanket Goswami <Sanket.Goswami@amd.com>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
Implement the i2c_algorithm operations to enable support for AMD ASF
(Alert Standard Format) with SMBus. This enhancement includes:
- Adding functionality to identify and select the supported ASF functions.
- Implementing mechanisms for registering and deregistering I2C slave
devices.
- Providing support for data transfer operations over ASF.
Additionally, include a 'select' Kconfig entry as the current patch
utilizes .reg_slave() and .unreg_slave() callbacks, which are controlled
by CONFIG_I2C_SLAVE.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Co-developed-by: Sanket Goswami <Sanket.Goswami@amd.com>
Signed-off-by: Sanket Goswami <Sanket.Goswami@amd.com>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
The AMD ASF controller is presented to the operating system as an ACPI
device. The AMD ASF driver can use ACPI to obtain information about the
ASF controller's attributes, such as the ASF address space and interrupt
number, and to handle ASF interrupts.
Currently, the piix4 driver assumes that a specific port address is
designated for AUX operations. However, with the introduction of ASF, the
same port address may also be used by the ASF controller. Therefore, a
check needs to be added to ensure that if ASF is advertised and enabled in
ACPI, the AUX port should not be configured.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Co-developed-by: Sanket Goswami <Sanket.Goswami@amd.com>
Signed-off-by: Sanket Goswami <Sanket.Goswami@amd.com>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
Export the following i2c_piix4 driver functions as a library so that the
AMD ASF driver can utilize these core functionalities from the i2c_piix4
driver:
- piix4_sb800_region_request(): Request access to a specific SMBus region
on the SB800 chipset.
- piix4_sb800_region_release(): Release the previously requested SMBus
region on the SB800 chipset.
- piix4_transaction(): Handle SMBus transactions between the SMBus
controller and connected devices.
- piix4_sb800_port_sel(): Select the appropriate SMBus port on the SB800
chipset.
By making these functions available as a library, enable the AMD ASF
driver to leverage the established mechanisms in the i2c_piix4 driver,
promoting code reuse and consistency across different drivers.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Co-developed-by: Sanket Goswami <Sanket.Goswami@amd.com>
Signed-off-by: Sanket Goswami <Sanket.Goswami@amd.com>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
Add a separate header file to relocate the common code from the i2c_piix4
driver, allowing the AMD ASF driver to utilize the same code.
Update the MAINTAINERS file to include information about the new common
header file.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Co-developed-by: Sanket Goswami <Sanket.Goswami@amd.com>
Signed-off-by: Sanket Goswami <Sanket.Goswami@amd.com>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
Currently, `piix4_transaction()` accepts only one parameter, which is the
`i2c_adapter` information. This approach works well as long as SB800 SMBus
port accesses are confined to the piix4 driver. However, with the
implementation of a separate ASF driver and the varying address spaces
across drivers, it is necessary to change the function parameter list of
`piix4_transaction()` to include the port address. This modification
allows other drivers that use piix4 to pass the specific port details they
need to operate on.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Co-developed-by: Sanket Goswami <Sanket.Goswami@amd.com>
Signed-off-by: Sanket Goswami <Sanket.Goswami@amd.com>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
Add SMBus PCI IDs on Intel Panther Lake-P and -U.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
Convert existing descriptions to kernel-doc format and unify
the rest of the comments to follow the modern style.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
Octal permissions are preferred over the symbolics ones
for readbility. This ceases warning message pointed by checkpatch.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
Update header inclusions to follow IWYU (Include What You Use)
principle.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
There are two different names used for the variable that holds
an error code. Unify to use one variant in all cases.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
Simplify the code by using read_poll_timeout().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
Introduce a temporary variable to hold a device pointer.
It can be utilized in the ->probe() and save a bit of LoCs.
To make it consistent, rename currently used dev to pdev.
While at it, convert the only error message to dev_err_probe().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
Switch from i2c_add_adapter() to resource managed devm_i2c_add_adapter()
for matching rest of driver initialization, and more concise code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
Use custom private data structure instead of global variables.
With that, remove not anymore true comment.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
Convert driver to use memory mapped IO accessors.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
Use modern string_choices API instead of manually determining the
output using ternary operator.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
There are a lot of messaging calls that use global variable of
struct i2c_adapter. Instead, to make code better and flexible
for further improvements, pass the pointer to the actual adapter
used for transfers.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
Rework the read and write code paths in the driver to support operation
in atomic contexts in master mode. This change does not apply to slave
mode because there is no way to handle interruptions in that context.
Adjust the message timeout to include some extra time. For non-atomic
contexts, 500 ms is added to the timeout. For atomic contexts,
2000 ms is added because transfers happen in polled mode, requiring
more time to account for the polling overhead.
Similar changes have been implemented in other drivers, including:
commit 3a5ee18d2a32 ("i2c: imx: implement master_xfer_atomic callback")
commit 445094c8a9fb ("i2c: exynos5: add support for atomic transfers")
commit ede2299f7101 ("i2c: tegra: Support atomic transfers")
commit fe402bd09049 ("i2c: meson: implement the master_xfer_atomic
callback")
Signed-off-by: Manikanta Guntupalli <manikanta.guntupalli@amd.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
The cdns_i2c_master_xfer function has been refactored to separate
the common code. This change facilitates better support for atomic
mode operations by isolating the shared logic.
Signed-off-by: Manikanta Guntupalli <manikanta.guntupalli@amd.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
to facilitate atomic mode
Relocate cdns_i2c_runtime_suspend, cdns_i2c_runtime_resume and
cdns_i2c_init functions to avoid prototype statement in atomic
mode changes.
Signed-off-by: Manikanta Guntupalli <manikanta.guntupalli@amd.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
