| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Label the spi nor as serial_flash. This allows us to disable the
flash with an overlay common to all am6xx-phycore-som boards.
Signed-off-by: Nathan Morrisson <nmorrisson@phytec.com>
Link: https://lore.kernel.org/r/20240613230759.1984966-2-nmorrisson@phytec.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
J721E common processor board can be interfaced with the infotainment
expansion board[0] to enable the following audio/video interfaces in
addition to the peripherals provided by the common processor board:
- Two Audio codecs each with three Stereo Inputs and four Stereo Outputs
- Audio input over FPD Link III
- Digital Audio Interface TX/RX
- HDMI/FPD LINK III Display out
- LI/OV Camera input
Add support for TFP410 HDMI bridge located on the Infotainment Expansion
Board (connected to J46 & J51).
Add a HDMI connector node and connect the endpoints as below:
DSS => TFP410 bridge => HDMI connector
Also add the pinmux data and board muxes for DPI.
Rest of the peripherals are not added as of now.
[0]: <https://www.ti.com/lit/ug/spruit0a/spruit0a.pdf>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
[j-choudhary@ti.com: minor cleanup]
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Reviewed-by: Aradhya Bhatia <a-bhatia1@ti.com>
Link: https://lore.kernel.org/r/20240613093706.480700-1-j-choudhary@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Add an overlay to enable PCIe on the am642-phyboard-electra. The
serdes is muxed from USB to PCIe, so we are restricted to USB2 while
using this overlay.
Signed-off-by: Nathan Morrisson <nmorrisson@phytec.com>
Reviewed-by: Wadim Egorov <w.egorov@phytec.de>
Link: https://lore.kernel.org/r/20240613195012.1925920-3-nmorrisson@phytec.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Remove pinmuxing for PCIe so that we can add it in an overlay.
Signed-off-by: Nathan Morrisson <nmorrisson@phytec.com>
Reviewed-by: Wadim Egorov <w.egorov@phytec.de>
Link: https://lore.kernel.org/r/20240613195012.1925920-2-nmorrisson@phytec.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Add dts nodes for 6 EHRPWM instances on SoC.
Signed-off-by: Dasnavis Sabiya <sabiya.d@ti.com>
Signed-off-by: Udit Kumar <u-kumar1@ti.com>
Link: https://lore.kernel.org/r/20240603112938.2188510-1-u-kumar1@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
The SK-AM64 board has two TMP100 temperature sensors, add these here.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240612183826.121856-1-afd@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
The AM69-SK board has 3 instances of PCIe namely PCIe0, PCIe1 and PCIe3.
The x4 PCIe0 instance is connected to a Card Edge connector via SERDES1.
The x2 PCIe1 instance is connected to an M.2 M Key connector via SERDES0.
The x1 PCIe3 instance is connected to an M.2 E Key connector via SERDES0.
Add device-tree support for enabling all 3 PCIe instances in Root-Complex
mode of operation.
Signed-off-by: Dasnavis Sabiya <sabiya.d@ti.com>
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Link: https://lore.kernel.org/r/20240529082259.1619695-5-s-vadapalli@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Add overlay to enable the PCIe0 and PCIe1 instances of PCIe on J784S4-EVM
in Endpoint mode of operation.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Link: https://lore.kernel.org/r/20240529082259.1619695-4-s-vadapalli@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Enable PCIe0 and PCIe1 instances of PCIe in Root Complex mode of
operation on J784S4 EVM. The lanes of PCIe0 are connected to Serdes1
instance of Serdes while the lanes of PCIe1 are connected to Serdes0
instance of Serdes in J784S4 SoC. Despite both PCIe instances supporting
up to 4 Lanes, since the physical connections to the PCIe connector
corresponding to the PCIe1 instance of PCIe are limited to 2 Lanes on
the J784S4 EVM, update the "num-lanes" property of PCIe1 accordingly.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Link: https://lore.kernel.org/r/20240529082259.1619695-3-s-vadapalli@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
TI's J784S4 SoC has four instances of Gen3 PCIe Controllers namely
PCIe0, PCIe1, PCIe2 and PCIe3. PCIe0 and PCIe1 are 4-Lane controllers
while PCIe2 and PCIe3 are 2-Lane controllers.
Add support for the Root Complex Mode of operation of these PCIe instances.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Link: https://lore.kernel.org/r/20240529082259.1619695-2-s-vadapalli@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Add the "ethernet-mac-syscon" node within "wkup_conf" node corresponding to
the CTRLMMR_MAC_IDx registers within the CTRL_MMR space. Assign the
compatible "ti,am62p-cpsw-mac-efuse" to enable "syscon_regmap" operations
on these registers. The MAC Address programmed in the eFuse is accessible
through the CTRLMMR_MAC_IDx registers. The "ti,syscon-efuse" device-tree
property points to the CTRLMMR_MAC_IDx registers, allowing the CPSW driver
to fetch the MAC Address and assign it to the network interface associated
with CPSW3G MAC Port 1.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240604104425.3770037-1-s-vadapalli@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
1.4 GHz
The am625 is capable of running at 1.4 GHz when VDD_CORE is increased
from 0.75V to 0.85V. Increasing the voltage while the AM625 is
running has not been validated by TI, so we provide an overlay so that
people may choose to run at 1.4 GHz if they need the additional
performance.
Signed-off-by: Nathan Morrisson <nmorrisson@phytec.com>
Link: https://lore.kernel.org/r/20240425221925.1781226-1-nmorrisson@phytec.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
On SK-AM62P, McASP1 uses two pins for communicating with the codec over
I2S protocol. One of these pins (AXR0) is used for audio playback (TX)
so the direction of the pin should be OUTPUT.
Fixes: c00504ea42c0 ("arm64: dts: ti: k3-am62p5-sk: Updates for SK EVM")
Signed-off-by: Jai Luthra <j-luthra@ti.com>
Link: https://lore.kernel.org/r/20240606-mcasp_fifo_drop-v2-7-8c317dabdd0a@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
McASP AFIFOs are not necessary with UDMA-P/BCDMA as there is buffering
on the DMA IP. Drop these for better audio latency.
Fixes: 28c0cf16b308 ("arm64: dts: ti: k3-am625-phyboard-lyra-rdk: Add Audio Codec")
Signed-off-by: Jai Luthra <j-luthra@ti.com>
Link: https://lore.kernel.org/r/20240606-mcasp_fifo_drop-v2-6-8c317dabdd0a@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
McASP AFIFOs are not necessary with UDMA-P/BCDMA as there is buffering
on the DMA IP. Drop these for better audio latency.
Fixes: 316b80246b16 ("arm64: dts: ti: add verdin am62")
Acked-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Jai Luthra <j-luthra@ti.com>
Link: https://lore.kernel.org/r/20240606-mcasp_fifo_drop-v2-5-8c317dabdd0a@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
McASP AFIFOs are not necessary with UDMA-P/BCDMA as there is buffering
on the DMA IP. Drop these for better audio latency.
Fixes: 1f7226a5e52c ("arm64: dts: ti: k3-am625-beagleplay: Add HDMI support")
Signed-off-by: Jai Luthra <j-luthra@ti.com>
Link: https://lore.kernel.org/r/20240606-mcasp_fifo_drop-v2-4-8c317dabdd0a@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
McASP AFIFOs are not necessary with UDMA-P/BCDMA as there is buffering
on the DMA IP. Drop these for better audio latency.
Fixes: c00504ea42c0 ("arm64: dts: ti: k3-am62p5-sk: Updates for SK EVM")
Signed-off-by: Jai Luthra <j-luthra@ti.com>
Link: https://lore.kernel.org/r/20240606-mcasp_fifo_drop-v2-3-8c317dabdd0a@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
McASP AFIFOs are not necessary with UDMA-P/BCDMA as there is buffering
on the DMA IP. Drop these for better audio latency.
Fixes: 4a2c5dddf9e9 ("arm64: dts: ti: k3-am62a7-sk: Enable audio on AM62A")
Signed-off-by: Jai Luthra <j-luthra@ti.com>
Link: https://lore.kernel.org/r/20240606-mcasp_fifo_drop-v2-2-8c317dabdd0a@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
McASP AFIFOs are not necessary with UDMA-P/BCDMA as there is buffering
on the DMA IP. Drop these for better audio latency.
Fixes: b94b43715e91 ("arm64: dts: ti: Enable audio on SK-AM62(-LP)")
Signed-off-by: Jai Luthra <j-luthra@ti.com>
Link: https://lore.kernel.org/r/20240606-mcasp_fifo_drop-v2-1-8c317dabdd0a@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Add device tree overlay to enable both ICSSG1 ports available on AM64x-EVM
in MII mode.
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Reviewed-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Link: https://lore.kernel.org/r/20240429092919.657629-1-danishanwar@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
A PRU system event "vring" has been added to each PRU and RTU
node in each of the ICSSG0, ICSSG1 and ICSSG2 remote processor
subsystems to enable the virtio/rpmsg communication between MPU
and that PRU/RTU core. The additions are done in the base
k3-am65-main.dtsi, and so are inherited by all the K3 AM65x
boards.
The PRU system events is the preferred approach over using TI
mailboxes, as it eliminates an external peripheral access from
the PRU/RTU-side, and keeps the interrupt generation internal to
the ICSSG. The difference from MPU would be minimal in using one
versus the other.
Mailboxes can still be used if desired, but currently there is
no support on firmware-side for K3 SoCs to use mailboxes. Either
approach would require that an appropriate firmware image is
loaded/booted on the PRU.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Link: https://lore.kernel.org/r/20240529064420.571615-3-danishanwar@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
PRU system events "vring" have been added to each PRU and RTU node
in each of the ICSSG0 and ICSSG1 remote processor subsystems to
enable the virtio/rpmsg communication between MPU and that PRU/RTU core.
No events have been added to the Tx_PRU cores at present. The
additions are done in the base k3-am64main.dtsi, and so are inherited
by all the K3 AM64x boards.
The PRU system events is the preferred approach over using TI
mailboxes, as it eliminates an external peripheral access from
the PRU/RTU-side, and keeps the interrupt generation internal to
the ICSSG. The difference from MPU would be minimal in using one
versus the other.
Mailboxes can still be used if desired, but currently there is
no support on firmware-side for K3 SoCs to use mailboxes. Either
approach would require that an appropriate firmware image is
loaded/booted on the PRU.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Link: https://lore.kernel.org/r/20240529064420.571615-2-danishanwar@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Add Tulip TPS62873 nodes for J784S4 EVM. These are step-down regulators
that supply VDD_CPU_AVS and VDD_CORE_0V8 to the SoC.
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Link: https://lore.kernel.org/r/20240528040159.3919652-4-n-francis@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Add DTS node for two TPS6287x high current buck convertors.
The two TPS6287x supply power to the MAIN domain for AVS and other core
supplies.
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Link: https://lore.kernel.org/r/20240528040159.3919652-3-n-francis@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Add DTS node for LP87334E PMIC and two TPS6287x high current buck
converters.
LP87334E is responsible for supplying power to the MCU and MAIN domains
as well as to LPDDR4. The two TPS6287x supply power to the MAIN
domain for AVS and other core supplies.
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Link: https://www.ti.com/lit/pdf/slda060
Link: https://lore.kernel.org/r/20240528040159.3919652-2-n-francis@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
The board uses SERDES0 Lane 3 for USB3 IP. So update the
SerDes lane info for USB. Add the pin mux data and
enable USB3 support.
Signed-off-by: Matt Ranostay <mranostay@ti.com>
Signed-off-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Tested-by: Andrew Halaney <ahalaney@redhat.com> # k3-j784s4-evm
Link: https://lore.kernel.org/r/20240507095545.8210-3-r-gunasekaran@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Add support for the USB 3.0 controller
Signed-off-by: Matt Ranostay <mranostay@ti.com>
Signed-off-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Tested-by: Andrew Halaney <ahalaney@redhat.com> # k3-j784s4-evm
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20240507095545.8210-2-r-gunasekaran@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
CAN instances 0 and 1 in the mcu domain and 16 in the main domain are
brought on the evm through headers J42, J43 and J46 respectively. Thus,
add their respective transceiver's 0, 1 and 2 dt nodes to add support
for these CAN instances.
CAN instance 4 in the main domain is brought on the evm through header
J45. The CAN High and Low lines from the SoC are routed through a mux
on the evm. The select lines need to be set for the CAN signals to
reach to its transceiver on the evm. Therefore, add transceiver 3
dt node to add support for this CAN instance.
Signed-off-by: Bhavya Kapoor <b-kapoor@ti.com>
Link: https://lore.kernel.org/r/20240411201747.18697-1-b-kapoor@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
On-chip RTC is used as a wakeup source on am62a board designs. This
patch removes the disabled status property to enable the RTC node.
Signed-off-by: Vibhore Vardhan <vibhore@ti.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20240429184445.14876-1-vibhore@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
CAN instance 0 in the mcu domain is brought on the J721E-SK board
through header J1. Thus, add its respective transceiver 1 dt node to add
support for this CAN instance.
CAN instances 0, 5 and 9 in the main domain are brought on the J721E-SK
board through headers J5, J6 and J2 respectively. Thus, add their
respective transceivers 2, 3 and 4 dt nodes to add support for these CAN
instances.
Signed-off-by: Beleswar Padhi <b-padhi@ti.com>
Reviewed-by: Bhavya Kapoor <b-kapoor@ti.com>
Link: https://lore.kernel.org/r/20240430131512.1327283-1-b-padhi@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
J722S does not pin out all of the GPIO same as AM62P and have
more number of GPIO on the main_gpio1 instance. Fix the GPIO
count on both instances by overriding the ti,ngpio property.
Fixes: ea55b9335ad8 ("arm64: dts: ti: Introduce J722S family of SoCs")
More details at J722S/AM67 Datasheet (Section 5.3.11, GPIO):
https://www.ti.com/lit/ds/symlink/am67.pdf
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Link: https://lore.kernel.org/r/20240507103332.167928-1-vaishnav.a@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Add the bootph-all property to the memory node so that it can be
accessed by FDT functions at bootloader stage.
The bootloader requires the memory node to be able to initialize and set
the size of the DRAM banks. For this purpose, make sure all memory nodes
are present and standardized, and modify them if not.
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Link: https://lore.kernel.org/r/20240506110203.3230255-1-n-francis@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
The RS485 transceiver RE (Receiver enable) and DE (Driver enable) are
shorted and connected to both RTS/CTS of the SoC UART.
RE is active-low, DE is active-high.
Remove the "rs485-rts-active-low" flag to match RTS polarity with DE,
and fix communication in both transmit and receive directions.
Fixes: d60483faf914 ("arm64: dts: add description for solidrun am642 som and evaluation board")
Signed-off-by: Josua Mayer <josua@solid-run.com>
Link: https://lore.kernel.org/r/20240504-ti-rs485-rts-v1-1-e88ef1c96f34@solid-run.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Add a PMIC node to the phycore-am64 device tree.
Signed-off-by: Nathan Morrisson <nmorrisson@phytec.com>
Reviewed-by: Wadim Egorov <w.egorov@phytec.de>
Link: https://lore.kernel.org/r/20240429195830.4027250-2-nmorrisson@phytec.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
For main_pktdma node, the TX Channel Realtime Register region 'tchanrt'
is 128KB and Ring Realtime Register region 'ringrt' is 2MB as shown in
memory map in the TRM[0] (Table 2-1).
So fix ranges for those register regions.
[0]: <https://www.ti.com/lit/pdf/spruj83>
Fixes: b5080c7c1f7e ("arm64: dts: ti: k3-am62p: Add nodes for more IPs")
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Link: https://lore.kernel.org/r/20240430105253.203750-4-j-choudhary@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
For main_pktdma node, the TX Channel Realtime Register region 'tchanrt'
is 128KB and Ring Realtime Register region 'ringrt' is 2MB as shown in
memory map in the TRM[0] (Table 2-1).
So fix ranges for those register regions.
[0]: <https://www.ti.com/lit/pdf/spruj16>
Fixes: 3dad70def7ff ("arm64: dts: ti: k3-am62a-main: Add more peripheral nodes")
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Link: https://lore.kernel.org/r/20240430105253.203750-3-j-choudhary@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
For main_pktdma node, the TX Channel Realtime Register region 'tchanrt'
is 128KB and Ring Realtime Register region 'ringrt' is 2MB as shown in
memory map in the TRM[0] (Table 2-1).
So fix ranges for those register regions.
[0]: <https://www.ti.com/lit/pdf/spruiv7>
Fixes: c37c58fdeb8a ("arm64: dts: ti: k3-am62: Add more peripheral nodes")
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Link: https://lore.kernel.org/r/20240430105253.203750-2-j-choudhary@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
The CPSW9G instance of the CPSW Ethernet Switch supports USXGMII mode
with MAC Ports 1 and 2 of the instance, which are connected to ENET
Expansion 1 and ENET Expansion 2 slots on the EVM respectively, through
the Serdes2 instance of the SERDES.
Enable CPSW9G MAC Ports 1 and 2 in fixed-link configuration USXGMII mode
at 5 Gbps each.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Chintan Vankar <c-vankar@ti.com>
Link: https://lore.kernel.org/r/20240502091002.3659435-6-c-vankar@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
The J7 Quad Port Add-On Ethernet Card for J784S4 EVM supports
QSGMII mode. Use the overlay to configure CPSW9G ports in QSGMII
mode with the Add-On Ethernet Card connected to the ENET Expansion
1 slot on the EVM.
Add support to reset the PHY from kernel by using gpio-hog and
gpio-reset.
Add aliases for CPSW9G ports to enable kernel to fetch MAC Addresses
directly from U-Boot.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Chintan Vankar <c-vankar@ti.com>
Link: https://lore.kernel.org/r/20240502091002.3659435-5-c-vankar@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Enable MAIN CPSW2G and add alias for it to enable Linux to fetch
MAC Address for the port directly from U-Boot.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Signed-off-by: Chintan Vankar <c-vankar@ti.com>
Link: https://lore.kernel.org/r/20240502091002.3659435-4-c-vankar@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
J784S4 SoC has MAIN CPSW2G and CPSW9G instances of the CPSW
Ethernet Switch. CPSW2G has 1 external port and 1 host port
while CPSW9G has 8 external ports and 1 host port.
Add device-tree nodes for MAIN CPSW2G and CPSW9G and disable
them by default. MAIN CPSW2G will be enabled in the board file
while device-tree overlays will be used to enable CPSW9G.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Chintan Vankar <c-vankar@ti.com>
Link: https://lore.kernel.org/r/20240502091002.3659435-3-c-vankar@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Add alias for the MCU CPSW2G port to enable Linux to fetch MAC Address
for the port directly from U-Boot.
Signed-off-by: Chintan Vankar <c-vankar@ti.com>
Link: https://lore.kernel.org/r/20240502091002.3659435-2-c-vankar@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Add missing bootph-all property for CPSW MAC's PHY node
phy_gmii_sel.
Signed-off-by: Chintan Vankar <c-vankar@ti.com>
Link: https://lore.kernel.org/r/20240430085048.3143665-1-c-vankar@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
|
|
percpu.h depends on smp.h, but doesn't include it directly because of
circular header dependency issues; percpu.h is needed in a bunch of low
level headers.
This fixes a randconfig build error on mips:
include/linux/alloc_tag.h: In function '__alloc_tag_ref_set':
include/asm-generic/percpu.h:31:40: error: implicit declaration of function 'raw_smp_processor_id' [-Werror=implicit-function-declaration]
Reported-by: kernel test robot <lkp@intel.com>
Fixes: 24e44cc22aa3 ("mm: percpu: enable per-cpu allocation tagging")
Closes: https://lore.kernel.org/oe-kbuild-all/202405210052.DIrMXJNz-lkp@intel.com/
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/perf/perf-tools
Pull perf tool fix from Arnaldo Carvalho de Melo:
"Revert a patch causing a regression.
This made a simple 'perf record -e cycles:pp make -j199' stop working
on the Ampere ARM64 system Linus uses to test ARM64 kernels".
* tag 'perf-tools-fixes-for-v6.10-1-2024-05-26' of git://git.kernel.org/pub/scm/linux/kernel/git/perf/perf-tools:
Revert "perf parse-events: Prefer sysfs/JSON hardware events over legacy"
|
|
This reverts commit 617824a7f0f73e4de325cf8add58e55b28c12493.
This made a simple 'perf record -e cycles:pp make -j199' stop working on
the Ampere ARM64 system Linus uses to test ARM64 kernels, as discussed
at length in the threads in the Link tags below.
The fix provided by Ian wasn't acceptable and work to fix this will take
time we don't have at this point, so lets revert this and work on it on
the next devel cycle.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Bhaskar Chowdhury <unixbhaskar@gmail.com>
Cc: Ethan Adams <j.ethan.adams@gmail.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: James Clark <james.clark@arm.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Thomas Richter <tmricht@linux.ibm.com>
Cc: Tycho Andersen <tycho@tycho.pizza>
Cc: Yang Jihong <yangjihong@bytedance.com>
Link: https://lore.kernel.org/lkml/CAHk-=wi5Ri=yR2jBVk-4HzTzpoAWOgstr1LEvg_-OXtJvXXJOA@mail.gmail.com
Link: https://lore.kernel.org/lkml/CAHk-=wiWvtFyedDNpoV7a8Fq_FpbB+F5KmWK2xPY3QoYseOf_A@mail.gmail.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
Pull smb client fixes from Steve French:
- two important netfs integration fixes - including for a data
corruption and also fixes for multiple xfstests
- reenable swap support over SMB3
* tag '6.10-rc-smb3-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6:
cifs: Fix missing set of remote_i_size
cifs: Fix smb3_insert_range() to move the zero_point
cifs: update internal version number
smb3: reenable swapfiles over SMB3 mounts
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull misc fixes from Andrew Morton:
"16 hotfixes, 11 of which are cc:stable.
A few nilfs2 fixes, the remainder are for MM: a couple of selftests
fixes, various singletons fixing various issues in various parts"
* tag 'mm-hotfixes-stable-2024-05-25-09-13' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm:
mm/ksm: fix possible UAF of stable_node
mm/memory-failure: fix handling of dissolved but not taken off from buddy pages
mm: /proc/pid/smaps_rollup: avoid skipping vma after getting mmap_lock again
nilfs2: fix potential hang in nilfs_detach_log_writer()
nilfs2: fix unexpected freezing of nilfs_segctor_sync()
nilfs2: fix use-after-free of timer for log writer thread
selftests/mm: fix build warnings on ppc64
arm64: patching: fix handling of execmem addresses
selftests/mm: compaction_test: fix bogus test success and reduce probability of OOM-killer invocation
selftests/mm: compaction_test: fix incorrect write of zero to nr_hugepages
selftests/mm: compaction_test: fix bogus test success on Aarch64
mailmap: update email address for Satya Priya
mm/huge_memory: don't unpoison huge_zero_folio
kasan, fortify: properly rename memintrinsics
lib: add version into /proc/allocinfo output
mm/vmalloc: fix vmalloc which may return null if called with __GFP_NOFAIL
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixes from Ingo Molnar:
- Fix x86 IRQ vector leak caused by a CPU offlining race
- Fix build failure in the riscv-imsic irqchip driver
caused by an API-change semantic conflict
- Fix use-after-free in irq_find_at_or_after()
* tag 'irq-urgent-2024-05-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
genirq/irqdesc: Prevent use-after-free in irq_find_at_or_after()
genirq/cpuhotplug, x86/vector: Prevent vector leak during CPU offline
irqchip/riscv-imsic: Fixup riscv_ipi_set_virq_range() conflict
|
