| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
ENETC implement time specific departure capability, which enables
the user to specify when a frame can be transmitted. When this
capability is enabled, the device will delay the transmission of
the frame so that it can be transmitted at the precisely specified time.
The delay departure time up to 0.5 seconds in the future. If the
departure time in the transmit BD has not yet been reached, based
on the current time, the packet will not be transmitted.
This driver was loaded by Qos driver ETF. User could load it by tc
commands. Here are the example commands:
tc qdisc add dev eth0 root handle 1: mqprio \
num_tc 8 map 0 1 2 3 4 5 6 7 hw 1
tc qdisc replace dev eth0 parent 1:8 etf \
clockid CLOCK_TAI delta 30000 offload
These example try to set queue mapping first and then set queue 7
with 30us ahead dequeue time.
Then user send test frame should set SO_TXTIME feature for socket.
There are also some limitations for this feature in hardware:
- Transmit checksum offloads and time specific departure operation
are mutually exclusive.
- Time Aware Shaper feature (Qbv) offload and time specific departure
operation are mutually exclusive.
Signed-off-by: Po Liu <Po.Liu@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use resource_size rather than a verbose computation on
the end and start fields.
The semantic patch that makes these changes is as follows:
(http://coccinelle.lip6.fr/)
<smpl>
@@ struct resource ptr; @@
- (ptr.end + 1 - ptr.start)
+ resource_size(&ptr)
@@ struct resource *ptr; @@
- (ptr->end + 1 - ptr->start)
+ resource_size(ptr)
</smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The idtcm_caps structure is only copied into another structure,
so make it const.
The opportunity for this change was found using Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Only the SFC4000 code, now moved to sfc-falcon, needed I2C.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Acked-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit 8243186f0cc7 ("fs: remove ksys_dup()") and the
subsequent fix for it in commit 2d3145f8d280 ("early init: fix error
handling when opening /dev/console").
Trying to use filp_open() and f_dupfd() instead of pseudo-syscalls
caused more trouble than what is worth it: it requires accessing vfs
internals and it turns out there were other bugs in it too.
In particular, the file reference counting was wrong - because unlike
the original "open+2*dup" sequence it used "filp_open+3*f_dupfd" and
thus had an extra leaked file reference.
That in turn then caused odd problems with Androidx86 long after boot
becaue of how the extra reference to the console kept the session active
even after all file descriptors had been closed.
Reported-by: youling 257 <youling257@gmail.com>
Cc: Arvind Sankar <nivedita@alum.mit.edu>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
It can take on the values of '0', '1', and '2' and thus
is not a boolean.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
gcc produces a variable may be uninitialized warning for "val" in
parse_entry(). This is really a false positive, but the code is subtle
enough to just initialize val to zero and it's not a fast path to worry
about it.
Marked for stable to remove the warning in the stable trees as well.
Cc: stable@vger.kernel.org
Fixes: 6c3edaf9fd6a3 ("tracing: Introduce trace event injection")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
|
|
David Ahern says:
====================
tcp: Add support for L3 domains to MD5 auth
With VRF, the scope of network addresses is limited to the L3 domain
the device is associated. MD5 keys are based on addresses, so proper
VRF support requires an L3 domain to be considered for the lookups.
Leverage the new TCP_MD5SIG_EXT option to add support for a device index
to MD5 keys. The __tcpm_pad entry in tcp_md5sig is renamed to tcpm_ifindex
and a new flag, TCP_MD5SIG_FLAG_IFINDEX, in tcpm_flags determines if the
entry is examined. This follows what was done for MD5 and prefixes with
commits
8917a777be3b ("tcp: md5: add TCP_MD5SIG_EXT socket option to set a key address prefix")
6797318e623d ("tcp: md5: add an address prefix for key lookup")
Handling both a device AND L3 domain is much more complicated for the
response paths. This set focuses only on L3 support - requiring the
device index to be an l3mdev (ie, VRF). Support for slave devices can
be added later if desired, much like the progression of support for
sockets bound to a VRF and then bound to a device in a VRF. Kernel
code is setup to explicitly call out that current lookup is for an L3
index, while the uapi just references a device index allowing its
meaning to include other devices in the future.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add tests for new TCP MD5 API for L3 domains (VRF).
A new namespace is added to create a duplicate configuration between
the VRF and default VRF to verify overlapping config is handled properly.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add tests for existing TCP MD5 APIs - both single address
config and the new extended API for prefixes.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Update nettest to implement TCP_MD5SIG_EXT for a prefix and a device.
Add a new option, -m, to specify a prefix and length to use with MD5
auth. The device option comes from the existing -d option. If either
are set and MD5 auth is requested, TCP_MD5SIG_EXT is used instead of
TCP_MD5SIG.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On failure to set MD5 password, do_server should return 1 so that the
program exits with 1 rather than 255. This used for negative testing
when adding MD5 with device option.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for userspace to specify a device index to limit the scope
of an entry via the TCP_MD5SIG_EXT setsockopt. The existing __tcpm_pad
is renamed to tcpm_ifindex and the new field is only checked if the new
TCP_MD5SIG_FLAG_IFINDEX is set in tcpm_flags. For now, the device index
must point to an L3 master device (e.g., VRF). The API and error
handling are setup to allow the constraint to be relaxed in the future
to any device index.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add l3index to tcp_md5sig_key to represent the L3 domain of a key, and
add l3index to tcp_md5_do_add and tcp_md5_do_del to fill in the key.
With the key now based on an l3index, add the new parameter to the
lookup functions and consider the l3index when looking for a match.
The l3index comes from the skb when processing ingress packets leveraging
the helpers created for socket lookups, tcp_v4_sdif and inet_iif (and the
v6 variants). When the sdif index is set it means the packet ingressed a
device that is part of an L3 domain and inet_iif points to the VRF device.
For egress, the L3 domain is determined from the socket binding and
sk_bound_dev_if.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The original ingress device index is saved to the cb space of the skb
and the cb is moved during tcp processing. Since tcp_v4_inbound_md5_hash
can be called before and after the cb move, pass dif and sdif to it so
the caller can save both prior to the cb move. Both are used by a later
patch.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The original ingress device index is saved to the cb space of the skb
and the cb is moved during tcp processing. Since tcp_v6_inbound_md5_hash
can be called before and after the cb move, pass dif and sdif to it so
the caller can save both prior to the cb move. Both are used by a later
patch.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Extract the typecast to (union tcp_md5_addr *) to a local variable
rather than the current long, inline declaration with function calls.
No functional change intended.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When we receive a D-SACK, where the sequence number satisfies:
undo_marker <= start_seq < end_seq <= prior_snd_una
we consider this is a valid D-SACK and tcp_is_sackblock_valid()
returns true, then this D-SACK is discarded as "old stuff",
but the variable first_sack_index is not marked as negative
in tcp_sacktag_write_queue().
If this D-SACK also carries a SACK that needs to be processed
(for example, the previous SACK segment was lost), this SACK
will be treated as a D-SACK in the following processing of
tcp_sacktag_write_queue(), which will eventually lead to
incorrect updates of undo_retrans and reordering.
Fixes: fd6dad616d4f ("[TCP]: Earlier SACK block verification & simplify access to them")
Signed-off-by: Pengcheng Yang <yangpc@wangsu.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixed Coding function and style issues
Signed-off-by: Niu Xilei <niu_xilei@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Ido Schimmel says:
====================
mlxsw: Allow setting default port priority
Petr says:
When LLDP APP TLV selector 1 (EtherType) is used with PID of 0, the
corresponding entry specifies "default application priority [...] when
application priority is not otherwise specified."
mlxsw currently supports this type of APP entry, but uses it only as a
fallback for unspecified DSCP rules. However non-IP traffic is prioritized
according to port-default priority, not according to the DSCP-to-prio
tables, and thus it's currently not possible to prioritize such traffic
correctly.
This patchset extends the use of the abovementioned APP entry to also set
default port priority (in patches #1 and #2) and then (in patch #3) adds a
selftest.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Send non-IP traffic to a port and observe that it gets prioritized
according to the lldptool app=$prio,1,0 rules.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When APP TLV selector 1 (EtherType) is used with PID of 0, the
corresponding entry specifies "default application priority [...] when
application priority is not otherwise specified."
mlxsw currently supports this type of APP entry, but uses it only as a
fallback for unspecified DSCP rules. However non-IP traffic is prioritized
according to port-default priority, not according to the DSCP-to-prio
tables, and thus it's currently not possible to prioritize such traffic
correctly.
Extend the use of the abovementioned APP entry to also set default port
priority.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add QPDP. This register controls the port default Switch Priority and
Color. The default Switch Priority and Color are used for frames where the
trust state uses default values. Currently there are two cases where this
applies: a port is in trust-PCP state, but a packet arrives untagged; and a
port is in trust-DSCP state, but a non-IP packet arrives.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Jesper Dangaard Brouer says:
====================
page_pool: NUMA node handling fixes
The recently added NUMA changes (merged for v5.5) to page_pool, it both
contains a bug in handling NUMA_NO_NODE condition, and added code to
the fast-path.
This patchset fixes the bug and moves code out of fast-path. The first
patch contains a fix that should be considered for 5.5. The second
patch reduce code size and overhead in case CONFIG_NUMA is disabled.
Currently the NUMA_NO_NODE setting bug only affects driver 'ti_cpsw'
(drivers/net/ethernet/ti/), but after this patchset, we plan to move
other drivers (netsec and mvneta) to use NUMA_NO_NODE setting.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When kernel is compiled without NUMA support, then page_pool NUMA
config setting (pool->p.nid) doesn't make any practical sense. The
compiler cannot see that it can remove the code paths.
This patch avoids reading pool->p.nid setting in case of !CONFIG_NUMA,
in allocation and numa check code, which helps compiler to see the
optimisation potential. It leaves update code intact to keep API the
same.
$ ./scripts/bloat-o-meter net/core/page_pool.o-numa-enabled \
net/core/page_pool.o-numa-disabled
add/remove: 0/0 grow/shrink: 0/3 up/down: 0/-113 (-113)
Function old new delta
page_pool_create 401 398 -3
__page_pool_alloc_pages_slow 439 426 -13
page_pool_refill_alloc_cache 425 328 -97
Total: Before=3611, After=3498, chg -3.13%
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The check in pool_page_reusable (page_to_nid(page) == pool->p.nid) is
not valid if page_pool was configured with pool->p.nid = NUMA_NO_NODE.
The goal of the NUMA changes in commit d5394610b1ba ("page_pool: Don't
recycle non-reusable pages"), were to have RX-pages that belongs to the
same NUMA node as the CPU processing RX-packet during softirq/NAPI. As
illustrated by the performance measurements.
This patch moves the NAPI checks out of fast-path, and at the same time
solves the NUMA_NO_NODE issue.
First realize that alloc_pages_node() with pool->p.nid = NUMA_NO_NODE
will lookup current CPU nid (Numa ID) via numa_mem_id(), which is used
as the the preferred nid. It is only in rare situations, where
e.g. NUMA zone runs dry, that page gets doesn't get allocated from
preferred nid. The page_pool API allows drivers to control the nid
themselves via controlling pool->p.nid.
This patch moves the NAPI check to when alloc cache is refilled, via
dequeuing/consuming pages from the ptr_ring. Thus, we can allow placing
pages from remote NUMA into the ptr_ring, as the dequeue/consume step
will check the NUMA node. All current drivers using page_pool will
alloc/refill RX-ring from same CPU running softirq/NAPI process.
Drivers that control the nid explicitly, also use page_pool_update_nid
when changing nid runtime. To speed up transision to new nid the alloc
cache is now flushed on nid changes. This force pages to come from
ptr_ring, which does the appropate nid check.
For the NUMA_NO_NODE case, when a NIC IRQ is moved to another NUMA
node, we accept that transitioning the alloc cache doesn't happen
immediately. The preferred nid change runtime via consulting
numa_mem_id() based on the CPU processing RX-packets.
Notice, to avoid stressing the page buddy allocator and avoid doing too
much work under softirq with preempt disabled, the NUMA check at
ptr_ring dequeue will break the refill cycle, when detecting a NUMA
mismatch. This will cause a slower transition, but its done on purpose.
Fixes: d5394610b1ba ("page_pool: Don't recycle non-reusable pages")
Reported-by: Li RongQing <lirongqing@baidu.com>
Reported-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
mv88e6xxx_port_set_cmode() relies on cmode stored in struct
mv88e6xxx_port to skip cmode update when the requested value matches the
cached value. It turns out that mv88e6xxx_port_hidden_write() might
change the port cmode setting as a side effect, so we can't rely on the
cached value to determine that cmode update in not necessary.
Force cmode update in mv88e6341_port_set_cmode(), to make
serdes configuration work again. Other mv88e6xxx_port_set_cmode()
callers keep the current behaviour.
This fixes serdes configuration of the 6141 switch on SolidRun Clearfog
GT-8K.
Fixes: 7a3007d22e8 ("net: dsa: mv88e6xxx: fully support SERDES on Topaz family")
Reported-by: Denis Odintsov <d.odintsov@traviangames.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
I noticed that randconfig builds with gcc no longer produce a lot of
ccache hits, unlike with clang, and traced this back to plugins
now being enabled unconditionally if they are supported.
I am now working around this by adding
export CCACHE_COMPILERCHECK=/usr/bin/size -A %compiler%
to my top-level Makefile. This changes the heuristic that ccache uses
to determine whether the plugins are the same after a 'make clean'.
However, it also seems that being able to just turn off the plugins is
generally useful, at least for build testing it adds noticeable overhead
but does not find a lot of bugs additional bugs, and may be easier for
ccache users than my workaround.
Fixes: 9f671e58159a ("security: Create "kernel hardening" config area")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Masahiro Yamada <masahiroy@kernel.org>
Link: https://lore.kernel.org/r/20191211133951.401933-1-arnd@arndb.de
Cc: stable@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
|
|
This adds logic to the user_notification_basic test to set a member
of struct seccomp_notif to an invalid value to ensure that the kernel
returns EINVAL if any of the struct seccomp_notif members are set to
invalid values.
Signed-off-by: Sargun Dhillon <sargun@sargun.me>
Suggested-by: Christian Brauner <christian.brauner@ubuntu.com>
Link: https://lore.kernel.org/r/20191230203811.4996-1-sargun@sargun.me
Fixes: 6a21cc50f0c7 ("seccomp: add a return code to trap to userspace")
Cc: stable@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
|
|
This patch is a small change in enforcement of the uapi for
SECCOMP_IOCTL_NOTIF_RECV ioctl. Specifically, the datastructure which
is passed (seccomp_notif) must be zeroed out. Previously any of its
members could be set to nonsense values, and we would ignore it.
This ensures all fields are set to their zero value.
Signed-off-by: Sargun Dhillon <sargun@sargun.me>
Reviewed-by: Christian Brauner <christian.brauner@ubuntu.com>
Reviewed-by: Aleksa Sarai <cyphar@cyphar.com>
Acked-by: Tycho Andersen <tycho@tycho.ws>
Link: https://lore.kernel.org/r/20191229062451.9467-2-sargun@sargun.me
Fixes: 6a21cc50f0c7 ("seccomp: add a return code to trap to userspace")
Cc: stable@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
|
|
The seccomp_notif structure should be zeroed out prior to calling the
SECCOMP_IOCTL_NOTIF_RECV ioctl. Previously, the kernel did not check
whether these structures were zeroed out or not, so these worked.
This patch zeroes out the seccomp_notif data structure prior to calling
the ioctl.
Signed-off-by: Sargun Dhillon <sargun@sargun.me>
Reviewed-by: Tycho Andersen <tycho@tycho.ws>
Reviewed-by: Christian Brauner <christian.brauner@ubuntu.com>
Link: https://lore.kernel.org/r/20191229062451.9467-1-sargun@sargun.me
Fixes: 6a21cc50f0c7 ("seccomp: add a return code to trap to userspace")
Cc: stable@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
|
|
The sizes by which seccomp_notif and seccomp_notif_resp are allocated are
based on the SECCOMP_GET_NOTIF_SIZES ioctl. This allows for graceful
extension of these datastructures. If userspace zeroes out the
datastructure based on its version, and it is lagging behind the kernel's
version, it will end up sending trailing garbage. On the other hand,
if it is ahead of the kernel version, it will write extra zero space,
and potentially cause corruption.
Signed-off-by: Sargun Dhillon <sargun@sargun.me>
Suggested-by: Tycho Andersen <tycho@tycho.ws>
Link: https://lore.kernel.org/r/20191230203503.4925-1-sargun@sargun.me
Fixes: fec7b6690541 ("samples: add an example of seccomp user trap")
Cc: stable@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
|
|
The ram_core.c routines treat przs as circular buffers. When writing a
new crash dump, the old buffer needs to be cleared so that the new dump
doesn't end up in the wrong place (i.e. at the end).
The solution to this problem is to reset the circular buffer state before
writing a new Oops dump.
Signed-off-by: Aleksandr Yashkin <a.yashkin@inango-systems.com>
Signed-off-by: Nikolay Merinov <n.merinov@inango-systems.com>
Signed-off-by: Ariel Gilman <a.gilman@inango-systems.com>
Link: https://lore.kernel.org/r/20191223133816.28155-1-n.merinov@inango-systems.com
Fixes: 896fc1f0c4c6 ("pstore/ram: Switch to persistent_ram routines")
Cc: stable@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
|
|
For callers that allocated a label for persistent_ram_new(), if the call
fails, they must clean up the allocation.
Suggested-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Fixes: 1227daa43bce ("pstore/ram: Clarify resource reservation labels")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/lkml/20191211191353.14385-1-navid.emamdoost@gmail.com
Signed-off-by: Kees Cook <keescook@chromium.org>
|
|
to irq mode
Under load, the RX side of the mscan driver can get stuck while TX still
works. Restarting the interface locks up the system. This behaviour
could be reproduced reliably on a MPC5121e based system.
The patch fixes the return value of the NAPI polling function (should be
the number of processed packets, not constant 1) and the condition under
which IRQs are enabled again after polling is finished.
With this patch, no more lockups were observed over a test period of ten
days.
Fixes: afa17a500a36 ("net/can: add driver for mscan family & mpc52xx_mscan")
Signed-off-by: Florian Faber <faber@faberman.de>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Make sure to always use the descriptors of the current alternate setting
to avoid future issues when accessing fields that may differ between
settings.
Signed-off-by: Johan Hovold <johan@kernel.org>
Fixes: d08e973a77d1 ("can: gs_usb: Added support for the GS_USB CAN devices")
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Make sure to use the current alternate setting when verifying the
interface descriptors to avoid binding to an invalid interface.
Failing to do so could cause the driver to misbehave or trigger a WARN()
in usb_submit_urb() that kernels with panic_on_warn set would choke on.
Fixes: aec5fb2268b7 ("can: kvaser_usb: Add support for Kvaser USB hydra family")
Cc: stable <stable@vger.kernel.org> # 4.19
Cc: Jimmy Assarsson <extja@kvaser.com>
Cc: Christer Beskow <chbe@kvaser.com>
Cc: Nicklas Johansson <extnj@kvaser.com>
Cc: Martin Henriksson <mh@kvaser.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
CAN sk_buffs
KMSAN sysbot detected a read access to an untinitialized value in the
headroom of an outgoing CAN related sk_buff. When using CAN sockets this
area is filled appropriately - but when using a packet socket this
initialization is missing.
The problematic read access occurs in the CAN receive path which can
only be triggered when the sk_buff is sent through a (virtual) CAN
interface. So we check in the sending path whether we need to perform
the missing initializations.
Fixes: d3b58c47d330d ("can: replace timestamp as unique skb attribute")
Reported-by: syzbot+b02ff0707a97e4e79ebb@syzkaller.appspotmail.com
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Tested-by: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: linux-stable <stable@vger.kernel.org> # >= v4.1
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Fix inconsistent IS_ERR and PTR_ERR in tcan4x5x_parse_config().
The proper pointer to be passed as argument is tcan4x5x->device_wake_gpio.
This bug was detected with the help of Coccinelle.
Fixes: 2de497356955 ("can: tcan45x: Make wake-up GPIO an optional GPIO")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
GPIO is unavailable
If the device state GPIO is not connected to the host then disable the
INH output from the TCAN device per section 8.3.5 of the data sheet.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
It's a good idea to reset a ip-block/spi device before using it, this
patch will reset the device.
And a generic reset function if needed elsewhere.
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The tcan4x5x_parse_config() function now performs action on the device
either reading or writing and a reset. If the devive has a switchable
power supppy (i.e. regulator is managed) it needs to be turned on.
So turn on the regulator if available. If the parsing fails, turn off
the regulator.
Fixes: 2de497356955 ("can: tcan45x: Make wake-up GPIO an optional GPIO")
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
register access
The m_can tries to detect if Non ISO Operation is available while in
standby mode, this function results in the following error:
| tcan4x5x spi2.0 (unnamed net_device) (uninitialized): Failed to init module
| tcan4x5x spi2.0: m_can device registered (irq=84, version=32)
| tcan4x5x spi2.0 can2: TCAN4X5X successfully initialized.
When the tcan device comes out of reset it goes in standby mode. The
m_can driver tries to access the control register but fails due to the
device being in standby mode.
So this patch will put the tcan device in normal mode before the m_can
driver does the initialization.
Fixes: 5443c226ba91 ("can: tcan4x5x: Add tcan4x5x driver to the kernel")
Cc: stable@vger.kernel.org
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Acked-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The common fast path check can be done under rcu_read_lock() and
doesn't need a reference count on the label. Only take a reference
count if entering the slow path.
Fixes reported hackbench regression
- sha1 79e178a57dae ("Merge tag 'apparmor-pr-2019-12-03' of
git://git.kernel.org/pub/scm/linux/kernel/git/jj/linux-apparmor")
hackbench -l (256000/#grp) -g #grp
128 groups 19.679 ±0.90%
- previous sha1 01d1dff64662 ("Merge tag 's390-5.5-2' of
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux")
hackbench -l (256000/#grp) -g #grp
128 groups 3.1689 ±3.04%
Reported-by: Vincent Guittot <vincent.guittot@linaro.org>
Tested-by: Vincent Guittot <vincent.guittot@linaro.org>
Tested-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Fixes: bce4e7e9c45e ("apparmor: reduce rcu_read_lock scope for aa_file_perm mediation")
Signed-off-by: John Johansen <john.johansen@canonical.com>
|
|
With commit df323337e507 ("apparmor: Use a memory pool instead per-CPU
caches, 2019-05-03"), AppArmor code was converted to use memory pools. In
that conversion, a bug snuck into the code that polices bind mounts that
causes all bind mounts to fail with -ENOMEM, as we erroneously error out
if `aa_get_buffer` returns a pointer instead of erroring out when it
does _not_ return a valid pointer.
Fix the issue by correctly checking for valid pointers returned by
`aa_get_buffer` to fix bind mounts with AppArmor.
Fixes: df323337e507 ("apparmor: Use a memory pool instead per-CPU caches")
Signed-off-by: Patrick Steinhardt <ps@pks.im>
Signed-off-by: John Johansen <john.johansen@canonical.com>
|
|
git://people.freedesktop.org/~agd5f/linux into drm-fixes
amd-drm-fixes-5.5-2020-01-01:
amdgpu:
- ATPX regression fix
- SMU metrics table locking fixes
- gfxoff fix for raven
- RLC firmware loading stability fix
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200101151307.5242-1-alexander.deucher@amd.com
|
|
git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
-sun4i: Fix double-free in connector/encoder cleanup (Stefan)
-malidp: Make vtable static (Ben)
Cc: Ben Dooks <ben.dooks@codethink.co.uk>
Cc: Stefan Mavrodiev <stefan@olimex.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Sean Paul <sean@poorly.run>
Link: https://patchwork.freedesktop.org/patch/msgid/20191231152503.GA46740@art_vandelay
|
|
https://github.com/ckhu-mediatek/linux.git-tags into drm-fixes
Mediatek DRM fixes for Linux 5.5
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: CK Hu <ck.hu@mediatek.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1577762298.23194.2.camel@mtksdaap41
|
|
Per confirmation with RLC firmware team, the RLC should
be unhalted after all RLC related firmwares uploaded.
However, in fact the RLC is unhalted immediately after
RLCG firmware uploaded. And that may causes unexpected
PSP hang on loading the succeeding RLC save restore
list related firmwares.
So, we correct the firmware loading sequence to load
RLC save restore list related firmwares before RLCG
ucode. That will help to get around this issue.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
1GbE Intel Wired LAN Driver Updates 2019-12-31
This series contains updates to e1000e, igb and igc only.
Robert Beckett provide an igb change to assist in keeping packets from
being dropped due to receive descriptor ring being full when receive
flow control is enabled. Create a separate function to setup SRRCTL to
ease in reuse and ensure that setting of the drop enable bit only if
receive flow control is not enabled.
Sasha adds support for scatter gather support in igc. Improve the
direct memory address mapping flow by optimizing/simplifying and more
clear. Update igc to use pci_release_mem_regions() instead of
pci_release_selected_regions(). Clean up function header comments to
align with the actual code. Adds support for 64 bit DMA access, to help
handle socket buffer fragments in high memory. Adds legacy power
management support in igc by implementing suspend, resume,
runtime_suspend/resume, and runtime_idle callbacks. Clean up references
to Serdes interface in igc since that interface is not supported for
i225 devices.
Alex replaces the pr_info calls with netdev_info in all cases related to
netdev link state, as suggested by Joe Perches.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
