| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Add sociopnext,syscon-uhs-mode prpperty to the SD node to refer the handle
of the control logic node.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Link: https://lore.kernel.org/r/20230207023514.29783-5-hayashi.kunihiko@socionext.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Add "syscon" compatible string to the nodes for soc-glue-debug
according to the DT schema.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Link: https://lore.kernel.org/r/20230207023514.29783-4-hayashi.kunihiko@socionext.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The nodes for glue layers should include "reg" property.
Add the property according to the DT schema.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Link: https://lore.kernel.org/r/20230207023514.29783-3-hayashi.kunihiko@socionext.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
with bindings
The node names for SoC-dependent controllers and PHYs should be
generic ones according to the DT schemas.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Link: https://lore.kernel.org/r/20230207023514.29783-2-hayashi.kunihiko@socionext.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/joel/bmc into arm/dt
ASPEED device tree updates for 6.3
- New machines
* Ufispace NCPLite AST2600 BMC
* Facebook Greatlakes AST2600 BMC
- Updates for ethanolx, bletchley and tyan s8036
* tag 'aspeed-6.3-devicetree' of git://git.kernel.org/pub/scm/linux/kernel/git/joel/bmc:
ARM: dts: aspeed: p10bmc: Enable UART2
ARM: dts: aspeed: Add device tree for Ufispace NCPLite BMC
dt-bindings: arm: aspeed: document Ufispace NCPLite BMC
dt-bindings: vendor-prefixes: Add prefix for Ufi Space
arm: dts: aspeed: tyan s8036: Enable kcs interrupts
ARM: dts: aspeed: bletchley: Enable wdtrst1
ARM: dts: aspeed: bletchley: Rename flash1 label
ARM: dts: aspeed: ethanolx: Add BIOS flash chip
ARM: dts: aspeed: ethanolx: Enable CTS/RTS pins on UART1
ARM: dts: aspeed: ethanolx: Add label for the master partition
ARM: dts: aspeed: ethanolx: Correct EEPROM device name
ARM: dts: aspeed: ethanolx: Enable VUART
ARM: dts: aspeed: greatlakes: Add Facebook greatlakes (AST2600) BMC
dt-bindings: arm: aspeed: add Facebook Greatlakes board
Link: https://lore.kernel.org/r/CACPK8XdbffU5yRSZF-zR2xv-+6aJK+hEXP8TOkW=SvS+nNTGxg@mail.gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux into arm/dt
SoCFPGA dts updates for v6.3
- Align UART node with bindings
- Add pinctrl properties for Stratix10/Agilex
- Change address-cells to 2 to support 64-bit address for fpga region
* tag 'socfpga_dts_updates_for_v6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux:
arm64: dts: socfpga: change address-cells to support 64-bit addressing
arm64: dts: stratix10: add i2c pins for pinctrl
arm64: dts: add pinctrl-single property for Stratix10/Agilex
ARM: dts: socfpga: align UART node name with bindings
Link: https://lore.kernel.org/r/20230206162425.311593-1-dinguyen@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/ti/linux into arm/dt
TI K3 device tree updates for v6.3
New features:
J784S4 SoC and EVM support
AM68 and AM69 StarterKit, phyBOARD-Electra-AM642, Siemens IoT2050 M.2
AM62A7 SK additional peripherals
AM62 SK USB support
Non critical fixes
AM62:
McSPI Clock ID fixes
MMC TAP value updates
J7200:
pinmux range update
All:
Cache DT node fixes
Cleanups:
Reorder dts Makefile entries alphabetically
* tag 'ti-k3-dt-for-v6.3' of https://git.kernel.org/pub/scm/linux/kernel/git/ti/linux: (25 commits)
arm64: dts: ti: Makefile: Rearrange entries alphabetically
arch: arm64: dts: Add support for AM69 Starter Kit
dt-bindings: arm: ti: Add binding for AM69 Starter Kit
arm64: dts: ti: iot2050: Add support for M.2 variant
dt-bindings: arm: ti: Add binding for Siemens IOT2050 M.2 variant
arm64: dts: ti: iot2050: Add layout of OSPI flash
arm64: dts: ti: k3-j7200: Fix wakeup pinmux range
arm64: dts: ti: k3-am68-sk: Add support for AM68 SK base board
arm64: dts: ti: Add initial support for AM68 SK System on Module
dt-bindings: arm: ti: Add binding for AM68 SK
arm64: dts: Update cache properties for ti
arm64: dts: ti: Add support for phyBOARD-Electra-AM642
dt-bindings: arm: ti: Add bindings for PHYTEC AM64x based hardware
arm64: dts: ti: k3-am62a7-sk: Enable USB1 node
arm64: dts: ti: k3-am62a7-sk: Enable ethernet port
arm64: dts: ti: k3-am62a-main: Add more peripheral nodes
arm64: dts: ti: k3-am62a-mcu: Add MCU domain peripherals
arm64: dts: ti: Add support for J784S4 EVM board
arm64: dts: ti: Add initial support for J784S4 SoC
dt-bindings: pinctrl: k3: Introduce pinmux definitions for J784s4
...
Link: https://lore.kernel.org/r/642cf238-43e5-d6fa-68b5-a9dfbc0277bf@ti.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gclement/mvebu into arm/dt
mvebu dt64 for 6.3 (part 1)
Do not use anymore "marvell,armada3710" compatible string for the
Armada 3720 boards.
* tag 'mvebu-dt64-6.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/gclement/mvebu:
arm64: dts: marvell: Fix compatible strings for Armada 3720 boards
Link: https://lore.kernel.org/r/87zg9w9j6l.fsf@BL-laptop
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gclement/mvebu into arm/dt
mvebu dt for 6.3 (part 1)
Fix errors reported by dtbs_check on dove boards
* tag 'mvebu-dt-6.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/gclement/mvebu:
ARM: dts: dove.dtsi: Move ethphy to fix schema error
Link: https://lore.kernel.org/r/87357oaxs0.fsf@BL-laptop
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32 into arm/dt
STM32 DT for v6.3, round 1
Highlights:
----------
- MPU:
- ST boards:
- Add following peripherals support on stm32mp13:
i2s, SAI, SPDIFRX, DFSDM, Timers
- Add timers support on stm32mp135f-dk board.
- Add decicated BSEC compatible on STM32MP13.
- Rename sound card on STM32MP15 DKx.
- Fix yaml validation issues.
* tag 'stm32-dt-for-v6.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32:
ARM: dts: stm32: fix compatible for BSEC on STM32MP13
ARM: dts: stm32: Update part number NVMEM description on stm32mp131
ARM: dts: stm32: Use new media bus type macros
ARM: dts: stm32: Fix User button on stm32mp135f-dk
ARM: dts: stm32: add timers support on stm32mp135f-dk
ARM: dts: stm32: add timer pins muxing for stm32mp135f-dk
ARM: dts: stm32: add timers support on stm32mp131
ARM: dts: stm32: add dfsdm node on stm32mp131
ARM: dts: stm32: add spdifrx node on stm32mp131
ARM: dts: stm32: add sai nodes on stm32mp131
ARM: dts: stm32: add i2s nodes on stm32mp131
ARM: dts: stm32: Remove the pins-are-numbered property
ARM: dts: stm32: rename sound card on stm32mp15xx-dkx
ARM: dts: stm32: remove sai kernel clock on stm32mp15xx-dkx
ARM: dts: stm32: Fix qspi pinctrl phandle for stm32mp151a-prtt1l
ARM: dts: stm32: Fix qspi pinctrl phandle for stm32mp157c-emstamp-argon
ARM: dts: stm32: Fix qspi pinctrl phandle for stm32mp15xx-dhcom-som
ARM: dts: stm32: Fix qspi pinctrl phandle for stm32mp15xx-dhcor-som
Link: https://lore.kernel.org/r/3e815504-e85e-cbd3-6e6d-4e5a7aa7469a@foss.st.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into arm/dt
Two new 32bit SoC were added, the rv1126 and rk3128.
New boards are thr rk3128-eval-board, and a number of rv1126-based compute
modules from Edgeble AI.
Also included are some dt-binding improvements with relevant Acks from
maintainers when the changes touch these areas.
* tag 'v6.3-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
dt-bindings: phy: rename phy-rockchip-inno-usb2.yaml
dt-bindings: soc: rockchip: grf: add rockchip,rk3288-dp-phy.yaml
dt-bindings: phy: rockchip: convert rockchip-dp-phy.txt to yaml
ARM: dts: rockchip: Enable Ethernet on rv1126 Neu2-IO
ARM: dts: rockchip: Add Ethernet GMAC node for RV1126
ARM: dts: rockchip: Add ethernet rgmiim1 pin-control for rv1126
dt-bindings: arm: rockchip: Add Edgeble Neural Compute Module 6
ARM: dts: rockchip: add brcmf node to rk3066a-mk808
ARM: dts: rockchip: add space between label and nodename nfc pinctrl on rk3128
ARM: dts: rockchip: add rk3128-evb
ARM: dts: rockchip: add rk3128 soc dtsi
dt-bindings: arm: rockchip: Add Rockchip RK3128 Evaluation board
ARM: dts: rockchip: Add Edgeble Neural Compute Module 2(Neu2) IO board
ARM: dts: rockchip: Add Edgeble RV1126 Neural Compute Module 2(Neu2)
dt-bindings: arm: rockchip: Add Edgeble Neural Compute Module 2
dt-bindings: vendor-prefixes: Add Edgeble AI Technologies Pvt. Ltd.
ARM: dts: rockchip: Add Rockchip RV1126 SoC
ARM: dts: rockchip: Add Rockchip RV1126 pinctrl
dt-bindings: arm: rockchip: Add pmu compatible for rv1126
Link: https://lore.kernel.org/r/5651506.31r3eYUQgx@phil
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into arm/dt
New SoC supported is the rk3588.
New boards rk3588-evb1, EmbedFire Lubancat 1+2 (based on different SoCs),
a number of Radxa boards (rock-5a and -5b, compute module 3, cm3i e25),
OrangePi R1 plus and the Edgeble Neu6 SoM and baseboard.
A number of improvements for the Odroid Go (and its clones) including
touchscreen and display support, led and audio changes.
As well as some improvements for the rk356x, better gpu thermal values for
px30 and some minor improvement for rock3a, rock5a, rk3566-demo,
roc-rk3399-pc and bi-r2pro.
* tag 'v6.3-rockchip-dts64-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip: (46 commits)
arm64: dts: rockchip: Correct the model name for Radxa E25
arm64: dts: rockchip: Drop unneeded model for Radxa CM3i
arm64: dts: rockchip: Add missing CM3i fallback compatible for Radxa E25
arm64: dts: rockchip: Fix compatible for Radxa CM3
arm64: dts: rockchip: rk3566: Enable WiFi, BT support for Radxa CM3
arm64: dts: rockchip: Enable Ethernet for Radxa CM3 IO
arm64: dts: rockchip: add display to RG503
arm64: dts: rockchip: add pinctrls for 16-bit/18-bit rgb interface to rk356x
arm64: dts: rockchip: Update eMMC, SD aliases for Radxa SBC boards
arm64: dts: rockchip: Update eMMC, SD aliases for Radxa SoM boards
arm64: dts: rockchip: Add Radxa Compute Module 3 IO board
arm64: dts: rockchip: Add rk3566 based Radxa Compute Module 3
dt-bindings: arm: rockchip: Add Radxa Compute Module 3
arm64: dts: rockchip: Fix RX delay for ethernet phy on rk3588s-rock5a
arm64: dts: rockchip: add Hynitron cst340 for Anbernic 353 series
arm64: dts: rockchip: Enable wifi module AP6398s for rk3566 box demo
arm64: dts: rockchip: rk3588: Add Edgeble Neu6 Model A IO
arm64: dts: rockchip: rk3588: Add Edgeble Neu6 Model A SoM
arm64: dts: rockchip: fix hdmi cec on rock-3a
arm64: dts: rockchip: assign rate to clk_rtc_32k on rk356x
...
Link: https://lore.kernel.org/r/6491956.DvuYhMxLoT@phil
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux into arm/dt
mt7986:
- add USB host support
- add support for mmc, pcie
- add support for Bananpi R3
mt8173:
- switch to SMC watchdog for Acer Chromebook R13
- move panel under aux bus
mt8183:
- support detachable keyboards on kukui based Chromebooks
- describe 13 MHz clock correctly
- complete CPU cache information
mt8186:
- Add pm-domains, iommu, dsi
- describe 13 MHz clock correctly
- complete CPU cache information
- add crypto support for the eMMC
- add audio controler, DPI and ADSP mailbox support
- describe CPUs as a single cluster
mt8192:
- describe 13 MHz clock correctly
- complete CPU cache information
- enable display regulators, backlight, internal display and audio on
Acer Chromebook 514
- describe CPUs as a single cluster
mt8195:
- Add power domain to t-phy
- describe 13 MHz clock correctly
- complete CPU cache information
- enable audio for Acer Chromebook Spin 513
- add ethernet support for the demo board
- add JPG enconder and decoder device
- describe CPUs as a single cluster
Smaller changes for mt6795, mt7622, mt8516 and mt6358.
* tag 'v6.2-next-dts64' of https://git.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux: (58 commits)
arm64: dts: mediatek: mt8516: Fix the watchdog node name
arm64: dts: mediatek: mt7986: Fix watchdog compatible
arm64: dts: mediatek: mt8195: Fix watchdog compatible
arm64: dts: mediatek: mt8186: Fix watchdog compatible
arm64: dts: mt8173-elm: Switch to SMC watchdog
arm64: dts: mediatek: mt7622: Add missing pwm-cells to pwm node
arm64: dts: mt8192: Change idle states names to reflect actual function
arm64: dts: mt8186: Change idle states names to reflect actual function
arm64: dts: mt8195: Change idle states names to reflect actual function
arm64: dts: mt8186: Fix CPU map for single-cluster SoC
arm64: dts: mt8192: Fix CPU map for single-cluster SoC
arm64: dts: mt8195: Fix CPU map for single-cluster SoC
arm64: dts: mt8195: add jpeg decode device node
arm64: dts: mt8195: add jpeg encode device node
arm64: dts: mediatek: mt8183: drop double interrupts
arm64: dts: mediatek: mt7622: drop serial clock-names
arm64: dts: mt8195: Add efuse node to mt8195
arm64: dts: mt8183: jacuzzi: Move panel under aux-bus
arm64: dts: mediatek: mt8173-elm: Move display to ps8640 auxiliary bus
arm64: dts: mt8195: Add Ethernet controller
...
Link: https://lore.kernel.org/r/2eefe6d4-6ca3-dc5f-6a04-f4f3c49692dd@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux into arm/dt
Clean ups only:
- deleting unsused pins-are-numbered property
- not existing second IRQ
* tag 'v6.2-next-dts32' of https://git.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux:
ARM: dts: mediatek: Remove pins-are-numbered property
arm: dts: mt7629: Remove extra interrupt from timer node
Link: https://lore.kernel.org/r/17aee808-1f3f-fe75-68d4-adb71915e5cb@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Use the correct compatible for stm32mp13 support.
The BSEC driver for STM32MP15x is not compatible with STM32MP13x. For
example the proprietary's smc STM32_SMC_BSEC is not supported in
STM32MP13x OP-TEE, it is replaced by SM32MP BSEC Pseudo Trusted
Application in OP-TEE to access to the secured IP BSEC on STM32MP13X SoC.
The correct compatible is already used in U-Boot and in upstream is in
progress for OP-TEE device tree.
As the SoC STM32MP13X is not yet official and it is not available
outside STMicroelectronics, it is the good time to break the DTS
compatibility and to correct the error done in the introduction of
STM32MP131.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
The STM32MP13x Device Part Number (also named RPN in reference manual)
only uses the first 12 bits in OTP4, all the other bit are reserved and
they can be different of zero; they must be masked in NVMEM result, so
the number of bits must be defined in the nvmem cell description.
Fixes: 1da8779c0029 ("ARM: dts: stm32: add STM32MP13 SoCs support")
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
Rename phy-rockchip-inno-usb2.yaml to a more common format of
rockchip,inno-usb2phy.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Acked-By: Vinod Koul <vkoul@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/99794484-d67e-ee1f-4e76-200de20a879c@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Entries are first grouped as per SoC present on the board. Groups are
sorted alphabetically. This makes it easy to know SoC to board mapping
and also add new entries in alphabetical order.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20230126071159.2337584-1-vigneshr@ti.com
|
|
AM69 Starter Kit is a single board designed for TI AM69 SOC that
provides advanced system integration in automotive ADAS applications,
autonomous mobile robot and edge AI applications. The SOC comprises
of Cortex-A72s in dual clusters, lockstep capable dual Cortex-R5F MCUs,
Vision Processing Accelerators (VPAC) with Image Signal Processor (ISP)
and multiple vision assist accelerators, Depth and Motion Processing
Accelerators (DMPAC), Deep-learning Matrix Multiply Accelerator(MMA)
and C7x floating point vector DSP
AM69 SK supports the following interfaces:
* 32 GB LPDDR4 RAM
* x1 Gigabit Ethernet interface
* x3 USB 3.0 Type-A ports
* x1 USB 3.0 Type-C port
* x1 UHS-1 capable micro-SD card slot
* x4 MCAN instances
* 32 GB eMMC Flash
* 512 Mbit OSPI flash
* x2 Display connectors
* x1 PCIe M.2 M Key
* x1 PCIe M.2 E Key
* x1 4L PCIe Card Slot
* x3 CSI2 Camera interface
* 40-pin Raspberry Pi header
Add initial support for the AM69 SK board.
Design Files: https://www.ti.com/lit/zip/SPRR466
TRM: https://www.ti.com/lit/zip/spruj52
Signed-off-by: Dasnavis Sabiya <sabiya.d@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20230119132958.124435-3-sabiya.d@ti.com
|
|
AM69 Starter Kit is a single board designed for TI AM69 SoC.
The AM69 SoC belongs to the K3 Multicore SoC architecture platform,
providing advanced system integration in automotive ADAS applications,
autonomous mobile robot and edge AI applications.
Add DT binding for AM69 Starter Kit.
Signed-off-by: Dasnavis Sabiya <sabiya.d@ti.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20230119132958.124435-2-sabiya.d@ti.com
|
|
ARM: Zynq DT changes for v6.3
- Fix node names to be aligned with dt schema
- Describe qspi controller
- Use xlnx prefix for ethernet IP
* tag 'zynq-dt-for-v6.3' of https://github.com/Xilinx/linux-xlnx:
ARM: zynq: Use recommended dma-controller name instead of dmac
ARM: dts: zynq: Add xlnx prefix to GEM compatible string
ARM: zynq: Comment interrupt names IRQs for pl330
ARM: dts: zynq: add QSPI controller node
Link: https://lore.kernel.org/r/850bb18f-ca22-f3d7-71a7-f367bfef4ccc@monstr.eu
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
arm/dt
arm64: ZynqMP SOC changes for v6.3
- Fix node names to be aligned with dt schema
- Rename DT overlay files to dtso
- Add snps,resume-hs-terminations to usb nodes
- Describe gpio-modepin node
- Use xlnx prefix for ethernet IP
* tag 'zynqmp-dt-for-v6.3' of https://github.com/Xilinx/linux-xlnx:
arm64: dts: zynqmp: Add xlnx prefix to GEM compatible string
arm64: dts: zynqmp: Remove clock-names from GEM in zynqmp-clk-ccf.dtsi
arm64: dts: zynqmp: Add mode-pin GPIO controller DT node
arm64: zynqmp: Enable hs termination flag for USB dwc3 controller
arm64: dts: xilinx: Rename DTB overlay source files from .dts to .dtso
arm64: xilinx: Fix opp-table-cpu
arm64: dts: xilinx: align LED node names with dtschema
Link: https://lore.kernel.org/r/89d82a7e-6b42-97ce-2912-aa7dec965ff2@monstr.eu
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The proper name is 'watchdog', not 'toprgu' and remove the unused
label.
Signed-off-by: Allen-KH Cheng <allen-kh.cheng@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://lore.kernel.org/r/20221108033209.22751-5-allen-kh.cheng@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
|
|
MT7986's watchdog embeds a reset controller and needs only the
mediatek,mt7986-wdt compatible string as the MT6589 one is there
for watchdogs that don't have any reset controller capability.
Fixes: 50137c150f5f ("arm64: dts: mediatek: add basic mt7986 support")
Signed-off-by: Allen-KH Cheng <allen-kh.cheng@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://lore.kernel.org/r/20221108033209.22751-4-allen-kh.cheng@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
|
|
MT8195's watchdog embeds a reset controller and needs only the
mediatek,mt8195-wdt compatible string as the MT6589 one is there
for watchdogs that don't have any reset controller capability.
Fixes: 37f2582883be ("arm64: dts: Add mediatek SoC mt8195 and evaluation board")
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Co-developed-by: Allen-KH Cheng <allen-kh.cheng@mediatek.com>
Signed-off-by: Allen-KH Cheng <allen-kh.cheng@mediatek.com>
Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://lore.kernel.org/r/20221108033209.22751-3-allen-kh.cheng@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
|
|
MT8186's watchdog embeds a reset controller and needs only the
mediatek,mt8186-wdt compatible string as the MT6589 one is there
for watchdogs that don't have any reset controller capability.
Fixes: 2e78620b1350 ("arm64: dts: Add MediaTek MT8186 dts and evaluation board and Makefile")
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Co-developed-by: Allen-KH Cheng <allen-kh.cheng@mediatek.com>
Signed-off-by: Allen-KH Cheng <allen-kh.cheng@mediatek.com>
Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://lore.kernel.org/r/20221108033209.22751-2-allen-kh.cheng@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
|
|
Switch to SMC watchdog because we need direct control of HW watchdog
registers from kernel. The corresponding firmware was uploaded in
https://review.trustedfirmware.org/c/TF-A/trusted-firmware-a/+/3405.
Signed-off-by: Pin-yen Lin <treapking@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220729053254.220585-1-treapking@chromium.org
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
|
|
Specify #pwm-cells on pwm@11006000 to make it actually usable.
Fixes: ae457b7679c4 ("arm64: dts: mt7622: add SoC and peripheral related device nodes")
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20221128112028.58021-2-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
|
|
All Armada 3720 boards have Armada 3720 processor which is of Armada 3700
family and do not have Armada 3710 processor. So none of them should have
compatible string for Armada 3710 processor.
Fix compatible string for all these boards by removing wrong processor
string "marvell,armada3710" and adding family string "marvell,armada3700"
as the last one. (Note that this is same way how are defined Armada 3710
DTS files).
[gclement: fix conflict for v6.2]
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
The APSS can be accessed over the second uart on these systems.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Link: https://lore.kernel.org/r/20230126220842.885965-1-eajames@linux.ibm.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
Running 'make dtbs_check' with schema in net/marvell,orion-mdio.yaml
gives following warnings:
mdio-bus@72004: Unevaluated properties are not allowed
('ethernet-phy' was unexpected)
arch/arm/boot/dts/dove-cubox.dtb
arch/arm/boot/dts/dove-cubox-es.dtb
arch/arm/boot/dts/dove-d2plug.dtb
arch/arm/boot/dts/dove-d2plug.dtb
arch/arm/boot/dts/dove-dove-db.dtb
arch/arm/boot/dts/dove-d3plug.dtb
arch/arm/boot/dts/dove-sbc-a510.dtb
As every subnode of mdio is expected to have an @X, ethernet-phy subnode
in dove.dtsi doesn't have one. Fix these errors by moving ethernet-phy
into relevant .dts files with correct @<reg address>.
Signed-off-by: Michał Grzelak <mig@semihalf.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
The names of the idle states are misleading being this a single cluster
SoC, a cluster-sleep idle state is impossible!
After some research in ATF, it emerged that the cpu-sleep state is in
reality putting CPUs in retention state, while the cluster-sleep one
is turning off the CPUs.
Summarizing renaming:
- cpu-sleep -> cpu-retention
- cluster-sleep -> cpu-off
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230126103526.417039-7-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
|
|
The names of the idle states are misleading being this a single cluster
SoC, a cluster-off idle state is impossible!
After some research in ATF, it emerged that the cpu-off state is in
reality putting CPUs in retention state, while the cluster-off one
is turning off the CPUs.
Summarizing renaming:
- cpu-off -> cpu-retention
- cluster-off -> cpu-off
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230126103526.417039-6-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
|
|
The names of the idle states are misleading being this a single cluster
SoC, a cluster-off idle state is impossible!
After some research in ATF, it emerged that the cpu-off state is in
reality putting CPUs in retention state, while the cluster-off one
is turning off the CPUs.
Summarizing renaming:
- cpu-off -> cpu-retention
- cluster-off -> cpu-off
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230126103526.417039-5-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
|
|
MT8186 features the ARM DynamIQ technology and combines both two
Cortex-A76 (big) and six Cortex-A55 (LITTLE) CPUs in one cluster:
fix the CPU map to reflect that.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Fixes: 2e78620b1350 ("arm64: dts: Add MediaTek MT8186 dts and evaluation board and Makefile")
Link: https://lore.kernel.org/r/20230126103526.417039-4-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
|
|
MT8192 features the ARM DynamIQ technology and combines both four
Cortex-A76 (big) and four Cortex-A55 (LITTLE) CPUs in one cluster:
fix the CPU map to reflect that.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Fixes: 48489980e27e ("arm64: dts: Add Mediatek SoC MT8192 and evaluation board dts and Makefile")
Link: https://lore.kernel.org/r/20230126103526.417039-3-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
|
|
MT8195 features the ARM DynamIQ technology and combines both four
Cortex-A78 (big) and four Cortex-A55 (LITTLE) CPUs in one cluster:
fix the CPU map to reflect that.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Fixes: 37f2582883be ("arm64: dts: Add mediatek SoC mt8195 and evaluation board")
Link: https://lore.kernel.org/r/20230126103526.417039-2-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/amlogic/linux into arm/dt
Amlogic ARM mach-meson changes for v6.3:
- align OPP table names with DT schema
- meson8/8b: Add more L2 (PL310) cache properties
- align LED node names with dtschema
* tag 'amlogic-arm-dt-for-v6.3' of https://git.kernel.org/pub/scm/linux/kernel/git/amlogic/linux:
ARM: dts: meson8: align OPP table names with DT schema
ARM: dts: meson8b: Add more L2 (PL310) cache properties
ARM: dts: meson8: Add more L2 (PL310) cache properties
ARM: dts: meson: align LED node names with dtschema
Link: https://lore.kernel.org/r/61700737-c226-1c07-fba7-6dca896fdab4@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/amlogic/linux into arm/dt
Amlogic ARM64 DT changes for v6.3:
- Merge of immutable bindings branch with Reset & power domain binding
- New boards:
- Odroid-N2L (Smaller version of Odroid-N2+)
- BananaPi M2-Pro (Variant of BPI=M5 with on-board wifi)
- Radxa Zero2 (New version of Radza Zero with A311D SoC)
- Add DT node for the VIPNano-QI on the A311D
- DT bindings fixups covering all SoC families
- MAC address nodes
- ethernet PHY node name
- scpi & child node names
- SD/SDIO node name
- USB supply name
- invalid clock-names
- rng node name
- rtc node name
- ETH phy mux node name
- button & adc keys node name
- leds node names
- RK818 pmic properties
- remove CPU opps below 1GHz for G12A boards, like it was done for G12B/SM1
- Fix WiFi/Bt definition around P212 & Khadas VIM1
- Add audio node to P212
- Fix FAN trip definition to Odroid-HC4
- Fix gpio-fan gpios definition
- Permit Radxa Zero OTG on USB1
- Fix VDDIO_C enable gpio by using OPEN DRAIN flag
* tag 'amlogic-arm64-dt-for-v6.3' of https://git.kernel.org/pub/scm/linux/kernel/git/amlogic/linux: (43 commits)
arm64: dts: meson: add support for Radxa Zero2
dt-bindings: arm: amlogic: add support for Radxa Zero2
arm64: dts: meson: add support for BananaPi M2-Pro
dt-bindings: arm: amlogic: add support for BananaPi M2-Pro
arm64: dts: meson: bananapi-m5: convert dts to dtsi
arm64: dts: meson: bananapi-m5: remove redundant status from sound node
arm64: dts: meson: bananapi-m5: switch VDDIO_C pin to OPEN_DRAIN
arm64: dts: meson: radxa-zero: allow usb otg mode
arm64: dts: meson-gxm-khadas-vim2: use gpio-fan matrix instead of an array
arm64: dts: meson-g12b-odroid: Add initial support for Hardkernel ODROID-N2L
arm64: dts: meson-g12b: move common node into new odroid.dtsi
dt-bindings: arm: amlogic: document Odroid-N2L
arm64: dts: amlogic: meson-sm1-odroid-hc4: fix active fan thermal trip
arm64: dts: meson: add audio playback to S905X-P212 dts
arm64: dts: meson: remove WiFi/BT nodes from Khadas VIM1
arm64: dts: meson: move pwm_ef node in P212 dtsi
arm64: dts: meson: add Broadcom WiFi to P212 dtsi
arm64: dts: amlogic: meson-g12b-odroid-go-ultra: fix rk818 pmic properties
arm64: dts: amlogic: meson-gxbb-kii-pro: fix led node name
arm64: dts: amlogic: meson-gxl-s905d-phicomm-n1: fix led node name
...
Link: https://lore.kernel.org/r/c1641ffd-71c9-9ac9-89d9-c22da4acea10@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/dt
i.MX arm64 device tree change for 6.3:
- New board support: i.MX8MP Beacon Kit, Debix Model A Board,
Verdin Yavia boards.
- Add Flexcan and ADC support for i.MX93.
- A series from Krzysztof Kozlowski to align LED node names with
dtschema and use generic node name for rave-sp.
- Move PCIe controller clock setup from board dts to SoC dtsi.
- Add clock-cells to i.MX8MP hsio-blk-ctrl device.
- Add TMU phandle to calibration data in OCOTP for i.MX8M.
- Improve bluetooth UART on DH electronics i.MX8M Plus DHCOM.
- Drop sd-vsel-gpios from i.MX8M Verdin SoM and DHCOM SoM.
- A series from Peng Fan to improve iomuxc-gpr device for i.MX8M.
- Declare IOMMU cache-coherent page table walk feature for LS1028A and
LS1088A.
- A few small corrections and random updates.
* tag 'imx-dt64-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (50 commits)
arm64: ls1046ardb: Use in-band-status for SFP module
arm64: dts: imx8mp-verdin: Add yavia carrier board
arm64: dts: imx8mm-verdin: Add yavia carrier board
arm64: dts: imx8q: use generic node name for rave-sp
arm64: dts: imx8mp-verdin-dev: Do not include dahlia dtsi
arm64: dts: imx8mm-verdin-dev: Do not include dahlia dtsi
arm64: dts: imx8mp: Drop sd-vsel-gpios from i.MX8M Plus DHCOM SoM
arm64: dts: imx8mp: Drop sd-vsel-gpios from i.MX8M Plus Verdin SoM
arm64: dts: imx8mm: Drop sd-vsel-gpios from i.MX8M Mini Verdin SoM
arm64: dts: imx8mp: Improve bluetooth UART on DH electronics i.MX8M Plus DHCOM
arm64: dts: freescale: Introduce imx8mp-beacon-kit
arm64: dts: imx8mm-evk: use correct gpio-expander compatible
arm64: dts: imx93: add ADC support
arm64: dts: imx8mp: Reorder clock to match fsl,imx6q-pcie.yaml
arm64: dts: imx8mq: Deduplicate PCIe clock-names property
arm64: dts: imx8mm: Deduplicate PCIe clock-names property
arm64: dts: verdin-imx8mp: unify gpio-key node name
arm64: dts: ls1028a: sl28: get MAC addresses from VPD
arm64: dts: freescale: Add LVDS overlay for TQMa8MPxL
arm64: dts: imx8mp: Add LCDIF2 & LDB nodes
...
Link: https://lore.kernel.org/r/20230130023947.11780-5-shawnguo@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/dt
i.MX arm device tree change for 6.3:
- New board support: SK-iMX53, DHCOM i.MX6ULL based boards.
- Increase MMC maximum frequency for i.MXRT1050.
- A series from Krzysztof Kozlowski to align LED node names with
dtschema, and use use generic node name for rave-sp device.
- Use new media bus type macros for i.MX device trees.
- A series from Marcel Ziswiler to improve gpio-key for Colibri and
Apalis device trees.
- A series from Marek Vasut to drop interrupt-names from dma-apb device.
- A series from Philippe Schenker to disable USB over-current for
Colibri and Apalis boards.
- A few other small corrections and random changes.
* tag 'imx-dt-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (29 commits)
ARM: dts: imx6ull-dhcom: Add DHSOM based DRC02 board
ARM: dts: imx6ull-dhcom: Add DHCOM based PicoITX board
ARM: dts: imx6ull-dhcom: Add DH electronics DHCOM i.MX6ULL SoM and PDK2 board
ARM: dts: imx7s: correct iomuxc gpr mux controller cells
ARM: dts: imx: use generic node name for rave-sp
ARM: dts: ls1021a: Disable CAN nodes by default
ARM: dts: apalis/colibri-imx6/6ull/7: proper gpio-key node names
ARM: dts: colibri-imx6ull: improve wake-up with gpio key
ARM: dts: colibri-imx6: improve wake-up with gpio key
ARM: dts: imx: e70k02: Add touchscreen
ARM: dts: vfxxx: Swap SAI DMA order
ARM: dts: freescale: Use new media bus type macros
ARM: dts: tqma6ul + mba6ulx: Fix temperature sensor compatible
ARM: dts: imx: Add support for SK-iMX53 board
ARM: dts: imx7s: Drop dma-apb interrupt-names
ARM: dts: imx6ul: Drop dma-apb interrupt-names
ARM: dts: imx6sx: Drop dma-apb interrupt-names
ARM: dts: imx6qdl: Drop dma-apb interrupt-names
ARM: dts: mxs: Drop dma-apb interrupt-names
ARM: dts: imx6qdl: use MAC-address from nvmem
...
Link: https://lore.kernel.org/r/20230130023947.11780-4-shawnguo@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/dt
i.MX DT bindings for 6.3:
- New board compatibles: Beacon EmbeddedWorks i.MX8M Plus kit,
DHCOM PDK2, PicoITX and DRC02, Enumerate Debix, Starterkit SK-iMX53,
verdin yavia carrier-board.
- Add vendor prefix for Polyhex Technology Co.
- A series from Krzysztof Kozlowski to fix up fsl,imx-gpc bindings.
- Add clock cells for imx8mp-hsio-blk-ctrl bindings.
- A series from Marek Vasut to shuffle i.MX8MM board entries.
- A couple changes from Stefan Wahren to update compatibles for i.MX28
based boards.
* tag 'imx-bindings-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
dt-bindings: arm: fsl: Add verdin yavia carrier-board
dt-bindings: arm: fsl: Add PDK2, PicoITX and DRC02 boards for the DHCOM i.MX6ULL SoM
dt-bindings: arm: Document the rest of i.MX28 based boards
dt-bindings: arm: fsl: Fix bindings for APF28Dev board
dt-bindings: power: fsl,imx-gpc: document interrupt-controller
dt-bindings: power: fsl,imx-gpc: correct compatibles
dt-bindings: power: fsl,imx-gpc: document fsl,imx6ul-gpc compatible
dt-bindings: arm: Add Beacon EmbeddedWorks i.MX8M Plus kit
dt-bindings: arm: Move i.MX8MM Cloos PHG Board to TQM entry
dt-bindings: arm: Split i.MX8M Plus DHCOM based boards
dt-bindings: arm: Split i.MX8M Mini NITROGEN SoM based boards
dt-bindings: arm: Move MX8Menlo board to i.MX8M Mini Toradex Verdin SoM entry
dt-bindings: soc: imx: add IOMUXC GPR support
dt-bindings: arm: fsl: Add the Starterkit SK-iMX53 board
dt-bindings: vendor-prefixes: add Startkit
dt-bindings: soc: imx8mp-hsio-blk-ctrl: add clock cells
dt-bindings: arm: fsl: Enumerate Debix Model A Board
dt-bindings: vendor-prefixes: Add Polyhex Technology Co.
Link: https://lore.kernel.org/r/20230130023947.11780-3-shawnguo@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux-dt into arm/dt
Minor improvements in ARM DTS for v6.3, part two
Align UART node names and OPP table names with bindings (alpine, arm
boards, axm55xx, berlin, cx92755, dm814x, moxart, mstar, stih418).
* tag 'dt-cleanup-6.3-2' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux-dt:
ARM: dts: berlin: align UART node name with bindings
ARM: dts: stih418: align OPP table names with DT schema
ARM: dts: dm814x: align UART node name with bindings
ARM: dts: moxart: align UART node name with bindings
ARM: dts: axm55xx: align UART node name with bindings
ARM: dts: alpine: align UART node name with bindings
ARM: dts: arm: align UART node name with bindings
ARM: dts: cx92755: align UART node name with bindings
ARM: dts: mstar: align UART node name with bindings
Link: https://lore.kernel.org/r/20230129144525.5802-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux-dt into arm/dt
Minor improvements in ARM64 DTS for v6.3, part two
1. Drop deprecated "device_type" property from serial nodes (apm,
amazon).
2. Align UART node names and OPP table names with bindings (hisilicon,
realtek, synaptics).
3. Use "okay" for status, as expected by Devicetree specification and
dtschema.
* tag 'dt64-cleanup-6.3-2' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux-dt:
arm64: dts: amd: use "okay" for status
arm64: dts: apm: use "okay" for status
arm64: dts: microchip: use "okay" for status
arm64: dts: synaptics: align UART node name with bindings
arm64: dts: hisilicon: align UART node name with bindings
arm64: dts: realtek: align UART node name with bindings
arm64: dts: amazon: drop deprecated serial device_type
arm64: dts: apm: drop deprecated serial device_type
Link: https://lore.kernel.org/r/20230129144525.5802-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into arm/dt
Samsung DTS ARM64 changes for v6.3, part two
Big cleanup and rework towards achieving zero-warning of dtbs_check and
dtc W=1:
- drop or correct incorrect properties in several boards,
- add dummy regulator supplies when necessary to fullfil bindings
requirements,
- use lowercase hex,
- move non-MMIO exynos-bus nodes out of soc node,
- add unit address to USB DWC3 nodes.
* tag 'samsung-dt64-6.3-2' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
arm64: dts: exynos: add unit address to DWC3 node wrapper in Exynos7
arm64: dts: exynos: add unit address to DWC3 node wrapper in Exynos5433
arm64: dts: exynos: move exynos-bus nodes out of soc in Exynos5433
arm64: dts: exynos: use lowercase hex addresses
arm64: dts: exynos: correct wlf,micd-dbtime on TM2
arm64: dts: exynos: add interrupt-controller to WM5110 on TM2
arm64: dts: exynos: add VPH_PWR regulator on TM2
arm64: dts: exynos: correct Bluetooth LED triger on E850-96
arm64: dts: exynos: add ADC supply on Exynos7 Espresso
arm64: dts: exynos: disable non-working GPU on Exynos7 Espresso
arm64: dts: exynos: drop unsupported UFS properties in ExynosAutov9 SADK
Link: https://lore.kernel.org/r/20230129143944.5104-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into arm/dt
Samsung DTS ARM changes for v6.3
1. Big cleanup and rework towards achieving zero-warning of dtbs_check
and dtc W=1:
- align node names with the bindings,
- drop or correct incorrect properties in several boards,
- correct HDMI bridge ports nodes on Exynos4412 Midas,
- add dummy regulator supplies when necessary to fullfil bindings
requirements,
- use lowercase hex,
- move non-MMIO exynos-bus nodes out of soc node,
- add unit address to USB DWC3 nodes.
2. Correct Exynos5420 MIPI DSI and phy compatibles.
3. Correct Exynos4210 and Exynos4412 HDMI phy compatibles.
4. Add Samsung Galaxy S5 (SM-G900H) board.
* tag 'samsung-dt-6.3' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux: (27 commits)
ARM: dts: exynos: add unit address to DWC3 node wrapper in Exynos54xx
ARM: dts: exynos: add unit address to DWC3 node wrapper in Exynos5250
ARM: dts: exynos: move exynos-bus nodes out of soc in Exynos4412
ARM: dts: exynos: move exynos-bus nodes out of soc in Exynos4210
ARM: dts: exynos: move exynos-bus nodes out of soc in Exynos3250
ARM: dts: exynos: move exynos-bus nodes out of soc in Exynos5420
ARM: dts: exynos: use lowercase hex addresses
ARM: dts: exynos: use generic node names for phy
ARM: dts: exynos: correct HDMI phy compatible in Exynos4
ARM: dts: exynos: Add Samsung Galaxy S5 (SM-G900H) board
dt-bindings: arm: samsung: Add compatible for Samsung Galaxy S5 (SM-G900H)
ARM: dts: exynos: Use Exynos5422 compatible for the DSI controller
ARM: dts: exynos: Use Exynos5420 compatible for the MIPI video phy
ARM: dts: exynos: correct HSI2C properties in Exynos5410 Odroid XU
ARM: dts: exynos: correct HS200 property in Exynos5260
ARM: dts: exynos: correct SATA clocks in Exynos5250
ARM: dts: exynos: align HSOTG/USB node names
ARM: dts: exynos: add backlight supply in P4 Note
ARM: dts: exynos: add panel supply in Tiny4412
ARM: dts: exynos: add ports in HDMI bridge in Exynos4412 Midas
...
Link: https://lore.kernel.org/r/20230129143944.5104-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://github.com/Broadcom/stblinux into arm/dt
This pull request contains Broadcom ARM64 SoCs Device Tree updates for
6.3, please pull the following:
- Krzysztof aligns the SMMMU Device Tree nodes to use the desired
regular expression matched by the dtschema and he also removes the
deprecated "device_type" property for serial node(s)
* tag 'arm-soc/for-6.3/devicetree-arm64' of https://github.com/Broadcom/stblinux:
arm64: dts: broadcom: drop deprecated serial device_type
arm64: dts: broadcom: align SMMU node names with DT schema
Link: https://lore.kernel.org/r/20230128193834.1628831-1-f.fainelli@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://github.com/Broadcom/stblinux into arm/dt
This pull request contains Broadcom ARM SoCs Device Tree updates for
6.3, please pull the following:
- Krzysztof aligns the various Broadcom SoCs DTS UART nodes with the
binding convention to use "serial"
* tag 'arm-soc/for-6.3/devicetree' of https://github.com/Broadcom/stblinux:
ARM: dts: broadcom: align UART node name with bindings
Link: https://lore.kernel.org/r/20230128193829.1628773-1-f.fainelli@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into arm/dt
- introduce Allwinner D1 DTSI
- add boards: Dongshan Nezha STU, MangoPi MQ (Pro), Sipeed Lichee RV,
Nezha
- add D1 power controller node
- Add SATA regulator to Bananapi M3
- fix regulator reference for nanopi-duo2
- fix GPIO node names
- align HDMI CEC node name for h3-beelink-x2
- add DPHY interrupt to A64 and A33
* tag 'sunxi-dt-for-6.3-1' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
riscv: dts: allwinner: d1: Add power controller node
riscv: Add the Allwinner SoC family Kconfig option
riscv: dts: allwinner: Add Dongshan Nezha STU devicetree
riscv: dts: allwinner: Add MangoPi MQ Pro devicetree
riscv: dts: allwinner: Add Sipeed Lichee RV devicetrees
riscv: dts: allwinner: Add Allwinner D1 Nezha devicetree
riscv: dts: allwinner: Add MangoPi MQ devicetree
riscv: dts: allwinner: Add the D1/D1s SoC devicetree
dt-bindings: riscv: Add Allwinner D1/D1s board compatibles
dt-bindings: vendor-prefixes: Add Allwinner D1/D1s board vendors
MAINTAINERS: Match the sun20i family of Allwinner SoCs
ARM: dts: sun8i: a83t: bananapi-m3: describe SATA disk regulator
ARM: dts: sun8i: nanopi-duo2: Fix regulator GPIO reference
ARM: dts: sunxi: Fix GPIO LED node names
ARM: dts: sun8i: h3-beelink-x2: align HDMI CEC node names with dtschema
arm64: dts: allwinner: a64: Add DPHY interrupt
ARM: dts: sun8i: a33: Add DPHY interrupt
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/dt
arm64: tegra: Device tree changes for v6.3-rc1
There are two big changes in this: one is to bump the #address-cells and
the #size-cells properties to 2 so that bus address translations work
correctly and another to sort nodes according to a scheme that we've
been trying to follow, but where some inconsistencies have accumulated
over the years.
As for the rest, this adds mostly new things on Tegra234, such as USB
host and device support and identification EEPROMs found on Jetson AGX
Orin.
Some cleanups are also included, such as the removal of unneeded
properties or duplicated nodes.
* tag 'tegra-for-6.3-arm64-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
arm64: tegra: Drop I2C iommus and dma-coherent properties
arm64: tegra: Mark host1x as dma-coherent on Tegra194/234
arm64: tegra: Populate the XUDC node for Tegra234
arm64: tegra: Add dma-coherent property for Tegra194 XUDC
arm64: tegra: Populate Jetson AGX Orin EEPROMs
arm64: tegra: Populate address/size cells for Tegra234 I2C
arm64: tegra: Enable XUSB host function on Jetson AGX Orin
arm64: tegra: Sort nodes by unit-address, then alphabetically
arm64: tegra: Bump #address-cells and #size-cells
arm64: tegra: Sort includes
arm64: tegra: Fix duplicate regulator on Jetson TX1
arm64: tegra: Fix typo in gpio-ranges property
Link: https://lore.kernel.org/r/20230127163719.460954-3-thierry.reding@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
