| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
This patch adds support for PF maximum bandwidth update
or configuration notified by management firmware.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds relevant APIs needed to configure WFQ
(Weighted fair queueing) values for the vports. WFQ configuration
is used per vport basis when minimum bandwidth update/configuration
is notified to the PF by the management firmware.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Hariprasad Shenai says:
====================
cxgb4: minor fixes, decode msgs and code refactor for few functions
This patch series adds new routine to get adapter information and removes
some redundant messages logged in dmesg. Fixes race while freeing tx
descriptors. Decodes module type and link down reason codes obtained from
firmware. Refactor port initialization and FW_PORT_CMD handling. Pass
correct port id in DCB message handler to obtain netdev associated.
This patch series has been created against net-next tree and includes
patches on cxgb4 driver.
We have included all the maintainers of respective drivers. Kindly review
the change and let us know in case of any review comments.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The firmware can send a set of asynchronous replies through FW_PORT_CMD
with DCBX information when that's negotiated with the Link Peer. The old
code always assumed that a FW_PORT_CMD reply was always a Get Port
Information message. This change conditionalizes the code to only handle
the Get Port Information messages and throws a warning if we don't
understand what we've been given.
Also refactor t4_handle_fw_rpl() so that core functionality performed by
t4_handle_get_port_info() for a specified port.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Refactor t4_port_init() so that the core functionality is done by
t4_init_portinfo() for a particular port. Also rename variables to
sensible ones.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Decode and log port module error, unknown modules and unsupported
modules.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There could be race between t4_eth_xmit() and t4_free_sge_resources() while
freeing tx descriptors, take txq lock in t4_free_sge_resources(). We need
to stop the xmit frame path which runs in bottom half context while
unloading the driver using _bh variant of the lock. This is to prevent
the deadlock between xmit and driver unload.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add new routine to print out general adapter information (various version
numbers, adapter name, part number, serial number, etc.) and remove
redundant information dumped in the Port Information.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next
Johan Hedberg says:
====================
pull request: bluetooth-next 2016-04-26
Here's another set of Bluetooth & 802.15.4 patches for the 4.7 kernel:
- Cleanups & refactoring of ieee802154 & 6lowpan code
- Security related additions to ieee802154 and mrf24j40 driver
- Memory corruption fix to Bluetooth 6lowpan code
- Race condition fix in vhci driver
- Enhancements to the atusb 802.15.4 driver
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If the PF driver reports proper support, allow the PF driver to
configure RSS on the behalf of the VF driver. This will allow for RSS
support on future hardware without changes to the VF driver.
Unfortunately, the old RSS code still needs to stay as the driver needs
to be compatible with PF drivers that don't support this interface. But
this change still simplifies the data structures a bunch and makes this
code simpler to read and maintain.
Change-ID: I0375aad40788ecdc0cb24d5cfeccf07804e69771
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
To add a little flexibility to the nvmupdate facility, this code adds the
ability to specify an AQ event opcode to wait on after the Exec_AQ request.
Change-ID: Iddbfd63c3de8df3edb9d3e90678b08989bc4946e
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Nicolas Dichtel says:
====================
netlink: align attributes when needed (patchset #3)
This is the continuation (series #3) of the work done to align netlink
attributes when these attributes contain some 64-bit fields.
It's the last patchset from what I've seen.
The last user of nla_put_u64() is block/drbd. This module does not use
standard netlink API (see all the stuff in include/linux/genl_magic_struct.h
and include/linux/genl_magic_func.h). I didn't modify it because it's seems
hard to do it whithout testing and fully understanding the context (for
example, why include/linux/drbd_genl.h is not part of uapi?).
Any thoughts?
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
I also fix commit 8b32ab9e6ef1: use nla_total_size_64bit() for
OVS_FLOW_ATTR_USED in ovs_flow_cmd_msg_size().
Fixes: 8b32ab9e6ef1 ("ovs: use nla_put_u64_64bit()")
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
I also fix the value of INET_DIAG_MAX. It's wrong since commit 8f840e47f190
which is only in net-next right now, thus I didn't make a separate patch.
Fixes: 8f840e47f190 ("sctp: add the sctp_diag.c file")
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Jan Kara <jack@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It was a simple idea -- save IPv6 configured addresses on a link down
so that IPv6 behaves similar to IPv4. As always the devil is in the
details and the IPv6 stack as too many behavioral differences from IPv4
making the simple idea more complicated than it needs to be.
The current implementation for keeping IPv6 addresses can panic or spit
out a warning in one of many paths:
1. IPv6 route gets an IPv4 route as its 'next' which causes a panic in
rt6_fill_node while handling a route dump request.
2. rt->dst.obsolete is set to DST_OBSOLETE_DEAD hitting the WARN_ON in
fib6_del
3. Panic in fib6_purge_rt because rt6i_ref count is not 1.
The root cause of all these is references related to the host route for
an address that is retained.
So, this patch deletes the host route every time the ifdown loop runs.
Since the host route is deleted and will be re-generated an up there is
no longer a need for the l3mdev fix up. On the 'admin up' side move
addrconf_permanent_addr into the NETDEV_UP event handling so that it
runs only once versus on UP and CHANGE events.
All of the current panics and warnings appear to be related to
addresses on the loopback device, but given the catastrophic nature when
a bug is triggered this patch takes the conservative approach and evicts
all host routes rather than trying to determine when it can be re-used
and when it can not. That can be a later optimizaton if desired.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit 841645b5f2dfceac69b78fcd0c9050868d41ea61.
Ok, this puts the feature back. I've decided to apply David A.'s
bug fix and run with that rather than make everyone wait another
whole release for this feature.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A little bit of code cleanup in prep for more cloud filter work.
Change-ID: I0dc33ce0d4c207944336a07437640fef920c100c
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Currently ARM CPUs DT bindings allows different enable-method value for
PSCI based systems. On ARM 64-bit this property is required and must be
"psci" while on ARM 32-bit systems this property is optional and must
be "arm,psci" if present.
However, "arm,psci" has always been the compatible string for the PSCI
node, and was never intended to be the enable-method. So this is a bug
in the binding and not a deliberate attempt at specifying 32-bit
differently.
This is problematic if 32-bit OS is run on 64-bit system which has
"psci" as enable-method rather than the expected "arm,psci".
So let's unify the value into "psci" and remove support for "arm,psci"
before it finds any users.
Reported-by: Soby Mathew <Soby.Mathew@arm.com>
Cc: Rob Herring <robh+dt@kernel.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Under some circumstances the driver remove function may be called before
the driver is fully initialized. So we can't assume that we know where
our towel is at, or that all of the data structures are initialized.
To ensure that we don't panic, check that the vsi_res pointer is valid
before dereferencing it. Then drink beer and eat peanuts.
Change-ID: If697b4db57348e39f9538793e16aa755e3e1af03
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Add support for configuring RSS on behalf of the VFs. This removes the
burden of dealing with different hardware interfaces from the VF
drivers, allowing for better future compatibility.
Change-ID: Icea75d3f37241ee8e447be5779e5abb53ddf04c0
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Looking over the documentation it turns out enabling IPIP and SIT offloads
for i40e is pretty straightforward. As such I decided to enable them with
this patch. In my testing I am seeing an improvement of 8 to 10 Gb/s
for IPIP and SIT tunnels with this offload enabled.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The feature flags list for i40e and i40evf is beginning to become pretty
massive. I plan to add another 4 or so features to these drivers and
duplicating the flags for each and every flags list is becoming a bit
repetitive.
The primary change here is that we now build our features list around
hw_encap_features. After that we assign that to vlan_features,
hw_features, and finally map that onto features. In addition we end up
throwing features onto hw_encap_features that end up having no effect such
as the Rx offloads and SCTP_CRC. However that should have no impact and
makes things a bit easier for us as hw_encap_features is one of the less
updated features maps available.
For i40evf I went through and sanity checked a few features as well.
Specifically RXCSUM was being set as a read-only feature which didn't make
much sense. I have updated things so we can clear the NETIF_F_RXCSUM flag
since that is really a software feature and not a hardware one anyway so
disabling it is just a matter of ignoring the result from the hardware.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Tom Herbert says:
====================
ila: Support for checksum neutral translations
This patch set updates ILA to support draft-herbert-nvo3-ila-02. The
primary addition is support checksum neutral ILA translation.
This allows address to be performed and still keep any transport
layer checksums that include the addresses in their pseudo header to
still be correct without the translator needing to parse L4.
Other items are:
- Structures for ILA addresses, identifiers, locators
- Disallow translation on non-ILA addresses (check by
type in identifier).
- Change xlat (nf_input) to translates solely based
on matching locators not identifiers (since identifiers
are not obfuscated by checksum neutral).
- Side effect if above is that multiple ILA domains are
supported. Each local locator can map to a different
SIR address (ILA domain), and each domain defines its
own identifier space.
Tested: Ran TCP_RR with 200 cnxs. ILA performance is slightly better
than previously since we are not longer parsing L4 for checksum
handling. I amd seeing about 1% performance overhead. Also ran
TCP_STREAM and tested non-ILA address (type=0) are not translated.
v2: Fix compilation errors
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Support checksum neutral ILA as described in the ILA draft. The low
order 16 bits of the identifier are used to contain the checksum
adjustment value.
The csum-mode parameter is added to described checksum processing. There
are three values:
- adjust transport checksum (previous behavior)
- do checksum neutral mapping
- do nothing
On output the csum-mode in the ila_params is checked and acted on. If
mode is checksum neutral mapping then to mapping and set C-bit.
On input, C-bit is checked. If it is set checksum-netural mapping is
done (regardless of csum-mode in ila params) and C-bit will be cleared.
If it is not set then action in csum-mode is taken.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Change model of xlat to be used only for input where lookup is done on
the locator part of an address (comparing to locator_match as key
in rhashtable). This is needed for checksum neutral translation
which obfuscates the low order 16 bits of the identifier. It also
permits hosts to be in muliple ILA domains (each locator can map
to a different SIR address). A check is also added to disallow
translating non-ILA addresses (check of type in identifier).
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add structures for identifiers, locators, and an ila address which
is composed of a locator and identifier and in6_addr can be cast to
it. This includes a three bit type field and enums for the types defined
in ILA I-D.
In ILA lwt don't allow user to set a translation for a non-ILA
address (type of identifier is zero meaning it is an IID). This also
requires that the destination prefix is at least 65 bytes (64
bit locator and first byte of identifier).
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When multiple skb are TX-completed in a row, we might incorrectly keep
a timestamp of a prior skb and cause extra work.
Fixes: ec693d47010e8 ("net/mlx4_en: Add HW timestamping (TS) support")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Ivan Babrou <ivan@cloudflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The first argument of pci_free_consistent has type struct pci_dev *, so use
NULL instead of 0.
The semantic patch that performs this transformation is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
@@
pci_free_consistent(
- 0
+ NULL
, ...)
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Yisen Zhuang says:
====================
net: hns: add support of debug dsaf device
There are two kinds of dsaf device in hns, one is for service ports,
contains crossbar in it, can work under different mode. Another is for
debug port, only can work under single port mode. The current code only
declares a dsaf device for both service ports and debug ports.It is not so
readability. This patch separates it to three platform devices to make the
code more simple and readability.
The diagram of all port in one platform device(old):
CPU
|
| DSAF(one platform device)
-------------------------------------------------------------- /
| | | | | /
| PPE PPE PPE | /
| | | | | /
| | | | | /
| crossbar | | | /
| | | | |/
| ----------------------------------- | | |
| | | | | | | | | |
| | | | | | | | | |
| MAC MAC MAC MAC MAC MAC MAC MAC |
| | | | | | | | | |
--------------------------------------------------------------
| | | | | | | |
PHY PHY PHY PHY PHY PHY PHY PHY
The diagram of separating ports to three platform(new):
CPU
|
-----------------------------------
| | |
---------------------------------------------- --------- ---------
| | | | | | | |
| PPE | | PPE | | PPE |
| | | | | | | | |
| | | | | | | | |
| crossbar | | | | | | |
| | | | | | | | |
| ---------------------------------- | | | | | | |
| | | | | | | | | | | | | |
| | | | | | | | | | | | | |
| MAC MAC MAC MAC MAC MAC | | MAC | | MAC |
| | | | | | | | | | | | | |
---------------------------------------------- --------- ---------
| | | | | | \ / | / |
PHY PHY PHY PHY PHY PHY \ / PHY / PHY
\ / /
\ / /
DSAF(three platform device)
We take the compatibility into consideration, and it works well by using the
old dts file(tested on d02 board).
For more details, please see individual patches.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Because debug dsaf port was separated from service dsaf port, this patch
updates the related configurations of hns dts, changes it to match with
the new binding files. This also removes enet nodes which don't exist in
d02 board.
Signed-off-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds description for port-idx-in-ae attribute.
Signed-off-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Because debug dsaf port was separated from service dsaf port, this patch
updates the related information of DT binding.
Signed-off-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Port mode offset for each dsaf port is different. The current code is not
so readability. This patch adds configuration named port-mode-offset to
make the code simple and more readability. If port-mode-offset isn't
exists, default value 0 will be used.
Signed-off-by: Daode Huang <huangdaode@hisilicon.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The reset offset for each port in a dsaf is different. The current code is
not so readability. This patch adds configuration named port-rst-offset to
make the code simple and more readability. If this attribute doesn't exist,
default value of this attribute is equal to its port index.
Signed-off-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds attribute cpld_ctrl for dsaf port node, parses the syscon
for mac_cb from dts, and changes the method of access the cpld related
registers through syscon.
Signed-off-by: Daode Huang <huangdaode@hisilicon.com>
Signed-off-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are two kinds of dsaf device in hns, one is for service ports,
contains crossbar in it, can work under different mode. Another is for
debug port, only can work under "single-port" mode. The current code only
declared a dsaf device for both service ports and debug ports. This patch
separate it to three platform devices.
Here is the diagram of all port in one platform device(old):
CPU
|
| DSAF(one platform device)
-------------------------------------------------------------- /
| | | | | /
| PPE PPE PPE | /
| | | | | /
| | | | | /
| crossbar | | | /
| | | | |/
| ----------------------------------- | | |
| | | | | | | | | |
| | | | | | | | | |
| MAC MAC MAC MAC MAC MAC MAC MAC |
| | | | | | | | | |
--------------------------------------------------------------
| | | | | | | |
PHY PHY PHY PHY PHY PHY PHY PHY
Here is the diagram of separate all ports to three platform(new):
CPU
|
-----------------------------------
| | |
---------------------------------------------- --------- ---------
| | | | | | | |
| PPE | | PPE | | PPE |
| | | | | | | | |
| | | | | | | | |
| crossbar | | | | | | |
| | | | | | | | |
| ---------------------------------- | | | | | | |
| | | | | | | | | | | | | |
| | | | | | | | | | | | | |
| MAC MAC MAC MAC MAC MAC | | MAC | | MAC |
| | | | | | | | | | | | | |
---------------------------------------------- --------- ---------
| | | | | | \ / | / |
PHY PHY PHY PHY PHY PHY \ / PHY / PHY
\ / /
\ / /
DSAF(three platform device)
Signed-off-by: Daode Huang <huangdaode@hisilicon.com>
Signed-off-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch tunes the header file by the alphabetical order.
Signed-off-by: Daode Huang <huangdaode@hisilicon.com>
Signed-off-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch provides the read/write function for dsaf to
access the registers through syscon methods.
Signed-off-by: Daode Huang <huangdaode@hisilicon.com>
Signed-off-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add the subctrl reset offset for dsaf, this property is used to reset
xge/ge ports for different dsaf. If this attribute is not present,
default value 0 will be used.
Signed-off-by: Daode Huang <huangdaode@hisilicon.com>
Signed-off-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch parse port-idx-in-ae in enet node. In NIC mode of DSAF, all 6
PHYs of service DSAF are taken as ethernet ports to the CPU. The
port-idx-in-ae can be 0 to 5. Here is the diagram:
+-----+---------------+
| CPU |
+-+-+-+---+-+-+-+-+-+-+
| | | | | | | |
debug debug service
port port port
(0) (0) (0-5)
In Switch mode of DSAF, all 6 PHYs of service DSAF are taken as physical
ports connect to a LAN Switch while the CPU side assume itself have one
single NIC connect to this switch. In this case, the port-idx-in-ae will
be 0 only.
+-----+-----+------+------+
| CPU |
+-+-+-+-+-+-+-+-+-+-+-+-+-+
| | service| port(0)
debug debug +------------+
port port | switch |
(0) (0) +-+-+-+-+-+-++
| | | | | |
external port
when port-idx-in-ae is not exists, old attribute port-id will be used
(only for compatible purpose, not recommended to use port-id in new code).
Signed-off-by: Daode Huang <huangdaode@hisilicon.com>
Signed-off-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
