| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Jakub Kicinski says:
====================
nfp: flower: loosen L4 checks and add extack to flower offload
Pieter says:
This set allows the offload of filters that make use of an unknown
ip protocol, given that layer 4 is being wildcarded. The set then
aims to make use of extack messaging for flower offloads. It adds
about 70 extack messages to the driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use extack messages in flower offload when compiling match and actions
messages that will configure hardware.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use extack messages in flower offload, specifically focusing on
the extack use in add offload, remove offload and get stats paths.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Matching on fields with a protocol that is unknown to hardware
is not strictly unsupported. Determine if hardware can offload
a filter with an unknown protocol by checking if any L4 fields
are being matched as well.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For better consistency of synthetic NIC names, we set the probe mode to
PROBE_FORCE_SYNCHRONOUS. So the names can be aligned with the vmbus
channel offer sequence.
Fixes: af0a5646cb8d ("use the new async probing feature for the hyperv drivers")
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2019-06-13
Mlx5 devlink health fw reporters and sw reset support
This series provides mlx5 firmware reset support and firmware devlink health
reporters.
1) Add initial mlx5 kernel documentation and include devlink health reporters
2) Add CR-Space access and FW Crdump snapshot support via devlink region_snapshot
3) Issue software reset upon FW asserts
4) Add fw and fw_fatal devlink heath reporters to follow fw errors indication by
dump and recover procedures and enable trigger these functionality by user.
4.1) fw reporter:
The fw reporter implements diagnose and dump callbacks.
It follows symptoms of fw error such as fw syndrome by triggering
fw core dump and storing it and any other fw trace into the dump buffer.
The fw reporter diagnose command can be triggered any time by the user to check
current fw status.
4.2) fw_fatal repoter:
The fw_fatal reporter implements dump and recover callbacks.
It follows fatal errors indications by CR-space dump and recover flow.
The CR-space dump uses vsc interface which is valid even if the FW command
interface is not functional, which is the case in most FW fatal errors. The
CR-space dump is stored as a memory region snapshot to ease read by address.
The recover function runs recover flow which reloads the driver and triggers fw
reset if needed.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Multipath hash policy value of 0 isn't distributing since the outer IP
dest and src aren't varied eventhough the inner ones are. Since the flow
is on the inner ones in the case of tunneled traffic, hashing on them is
desired.
This is done mainly for IP over GRE, hence only tested for that. But
anything else supported by flow dissection should work.
v2: Use skb_flow_dissect_flow_keys() directly so that other tunneling
can be supported through flow dissection (per Nikolay Aleksandrov).
v3: Remove accidental inclusion of ports in the hash keys and clarify
the documentation (Nikolay Alexandrov).
Signed-off-by: Stephen Suryaputra <ssuryaextr@gmail.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
NAPI tx mode improves TCP behavior by enabling TCP small queues (TSQ).
TSQ reduces queuing ("bufferbloat") and burstiness.
Previous measurements have shown significant improvement for
TCP_STREAM style workloads. Such as those in commit 86a5df1495cc
("Merge branch 'virtio-net-tx-napi'").
There has been uncertainty about smaller possible regressions in
latency due to increased reliance on tx interrupts.
The above results did not show that, nor did I observe this when
rerunning TCP_RR on Linux 5.1 this week on a pair of guests in the
same rack. This may be subject to other settings, notably interrupt
coalescing.
In the unlikely case of regression, we have landed a credible runtime
solution. Ethtool can configure it with -C tx-frames [0|1] as of
commit 0c465be183c7 ("virtio_net: ethtool tx napi configuration").
NAPI tx mode has been the default in Google Container-Optimized OS
(COS) for over half a year, as of release M70 in October 2018,
without any negative reports.
Link: https://marc.info/?l=linux-netdev&m=149305618416472
Link: https://lwn.net/Articles/507065/
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To remove rtnl lock dependency in tc filter update API when using clsact
Qdisc, set QDISC_CLASS_OPS_DOIT_UNLOCKED flag in clsact Qdisc_class_ops.
Clsact Qdisc ops don't require any modifications to be used without rtnl
lock on tc filter update path. Implementation never changes its q->block
and only releases it when Qdisc is being destroyed. This means it is enough
for RTM_{NEWTFILTER|DELTFILTER|GETTFILTER} message handlers to hold clsact
Qdisc reference while using it without relying on rtnl lock protection.
Unlocked Qdisc ops support is already implemented in filter update path by
unlocked cls API patch set.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Willem de Bruijn says:
====================
enable and use static_branch_deferred_inc
1. make static_branch_deferred_inc available if !CONFIG_JUMP_LABEL
2. convert the existing STATIC_KEY_DEFERRED_FALSE user to this api
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Deferred static key clean_acked_data_enabled uses the deferred
variants of dec and flush. Do the same for inc.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This interface is currently only defined if CONFIG_JUMP_LABEL. Make it
available also when jump labels are off.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Current flower mask creating code assumes that temporary mask that is used
when inserting new filter is stack allocated. To prevent race condition
with data patch synchronize_rcu() is called every time fl_create_new_mask()
replaces temporary stack allocated mask. As reported by Jiri, this
increases runtime of creating 20000 flower classifiers from 4 seconds to
163 seconds. However, this design is no longer necessary since temporary
mask was converted to be dynamically allocated by commit 2cddd2014782
("net/sched: cls_flower: allocate mask dynamically in fl_change()").
Remove synchronize_rcu() calls from mask creation code. Instead, refactor
fl_change() to always deallocate temporary mask with rcu grace period.
Fixes: 195c234d15c9 ("net: sched: flower: handle concurrent mask insertion")
Reported-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Tested-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When building with CONFIG_NET_DSA_REALTEK_SMI and CONFIG_REALTEK_PHY
enabled as loadable modules, we see the following warning:
warning: same module names found:
drivers/net/phy/realtek.ko
drivers/net/dsa/realtek.ko
Rework so the driver name is realtek-smi instead of realtek.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Based on comments from Xin, even after fixes for our recent syzbot
report of cookie memory leaks, its possible to get a resend of an INIT
chunk which would lead to us leaking cookie memory.
To ensure that we don't leak cookie memory, free any previously
allocated cookie first.
Change notes
v1->v2
update subsystem tag in subject (davem)
repeat kfree check for peer_random and peer_hmacs (xin)
v2->v3
net->sctp
also free peer_chunks
v3->v4
fix subject tags
v4->v5
remove cut line
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Reported-by: syzbot+f7e9153b037eac9b1df8@syzkaller.appspotmail.com
CC: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
CC: Xin Long <lucien.xin@gmail.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: netdev@vger.kernel.org
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Huazhong Tan says:
====================
net: hns3: some code optimizations & cleanups & bugfixes
This patch-set includes code optimizations, cleanups and bugfixes for
the HNS3 ethernet controller driver.
[patch 1/12 - 6/12] adds some code optimizations and bugfixes about RAS
and MSI-X HW error.
[patch 7/12] fixes a loading issue.
[patch 8/12 - 11/12] adds some bugfixes.
[patch 12/12] adds some cleanups, which does not change the logic of code.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch does following things:
1. add the keyword const before some variables which won't be modified
in functions.
2. changes some variables from signed to unsigned to avoid bitwise
operation on signed variables.
3. adds or removes initialization of some variables.
4. defines a new structure to help parsing mailbox messages instead of
using an array which is harder to get the meaning of each element.
Signed-off-by: Weihang Li <liweihang@hisilicon.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The driver may not be able to disable the ring through firmware
when downing the netdev during reset process, which may cause
hardware accessing freed buffer problem.
This patch delays the ring buffer clearing to reset uninit
process because hardware will not access the ring buffer after
hardware reset is completed.
Fixes: bb6b94a896d4 ("net: hns3: Add reset interface implementation in client")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If hns3_nic_net_xmit does not return NETDEV_TX_BUSY when doing
a loopback selftest, the skb is not freed in hns3_clean_tx_ring
or hns3_nic_net_xmit, which causes skb not freed problem.
This patch fixes it by freeing skb when hns3_nic_net_xmit does
not return NETDEV_TX_OK.
Fixes: c39c4d98dc65 ("net: hns3: Add mac loopback selftest support in hns3 driver")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The netdev is dereferenced before null checking in the function
hns3_setup_tc.
This patch moves the dereferencing after the null checking.
Fixes: 76ad4f0ee747 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In hns3_nic_init_irq(), if request irq fail at index i,
the function return directly without releasing irq resources
that already requested, and nowhere else will release them.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
IMP will set restting state for all function when PF FLR, driver
just clear the restting state in resetting progress, but don't do
it in initializing progress. As FLR is not created by driver,
it is necessary to clear restting state when initializing HW device.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Function hclge_handle_all_hw_msix_error() contains four parts:
1. Query buffer descriptors for MSI-X errors.
2. Query and clear all main PF MSI-X errors.
3. Query and clear all PF MSI-X errors.
4. Handle mac tunnel interrupts.
Part 2 and part 3 handle errors of some different modules respectively,
this patch extracts them into dividual functions, which makes the logic
clearer.
Signed-off-by: Weihang Li <liweihang@hisilicon.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch modifies print message of rx_q_search_miss from error to dfx to
prevent misleading users, because this interrupt may occur if we receive
packets during initialization of HNS3 driver.
Otherwise, this patch masks 28th bit of PPU_MPF_ABNORMAL_SRC2 which is now
meaningless.
Signed-off-by: Weihang Li <liweihang@hisilicon.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
initialization
This patch adds the recovery for the HNS H/W errors which occurred
before the driver initialization.
Reported-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: Shiju Jose <shiju.jose@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Presently the HNS driver enables the HNS H/W error interrupts after
the dev initialization is completed. However some exceptions such as
NCSI errors can occur when the network port driver is not loaded
and those errors required reporting to the BMC.
Therefore the firmware enabled all the HNS ras error interrupts
before the driver is loaded. And in some cases, there will be some
H/W errors remained unclear before reboot. Thus the HNS driver needs
to process and recover those hw errors occurred before HNS driver is
initialized.
This patch adds processing of the HNS hw errors(RAS and MSI-X)
which occurred before the driver initialization. For RAS, because
they are enabled by firmware, so we can detect specific bits, then
log and clear them. But for MSI-X which can not be enabled before
open vector0 irq, we can't detect the specific error bits, so we
just write 1 to all interrupt source registers to clear.
Signed-off-by: Shiju Jose <shiju.jose@huawei.com>
Signed-off-by: Weihang Li <liweihang@hisilicon.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
require reset
HNS does not need to be reset when errors occur in some bits.
However presently the HNAE3_FUNC_RESET is set in this case and
as a result the default_reset is done when these errors are reported.
This patch fix this issue. Also patch does some optimization
in setting the reset level for the error recovery.
Reported-by: Weihang Li <liweihang@hisilicon.com>
Signed-off-by: Shiju Jose <shiju.jose@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Presently the error handling code sets the reset level required
for the recovery of the hw errors to the reset framework in the
error_detected AER callback. However the rest_event would be
called later from the slot_reset callback. This can cause issue
of using the wrong reset_level if a high priority reset request
occur before the slot_reset is called.
This patch delays setting of the reset level, required
for the hw errors, to the reset framework until the
slot_reset is called.
Reported-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: Shiju Jose <shiju.jose@huawei.com>
Signed-off-by: Weihang Li <liweihang@hisilicon.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Michal Kalderon says:
====================
qed: iWARP fixes
This series contains a few small fixes related to iWARP.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The default window size is calculated for best performance based
on internal hw buffer sizes. The size differs between the
different chips and modes.
Fixes: 67b40dccc45f ("qed: Implement iWARP initialization, teardown and qp operations")
Signed-off-by: Ariel Elior <ariel.elior@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The driver needs to assign a lossless traffic class for the MPA ll2
connection to ensure no packets are dropped when returning from the
driver as they will never be re-transmitted by the peer.
Fixes: ae3488ff37dc ("qed: Add ll2 connection for processing unaligned MPA packets")
Signed-off-by: Ariel Elior <ariel.elior@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix uninitialized variable warning by static checker.
Fixes: ae3488ff37dc ("qed: Add ll2 connection for processing unaligned MPA packets")
Signed-off-by: Ariel Elior <ariel.elior@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Destroy QP waits for it's ep object state to be set to CLOSED
before proceeding. ep->state can be updated from a different
context. Add smp_store_release/READ_ONCE to synchronize.
Fixes: fc4c6065e661 ("qed: iWARP implement disconnect flows")
Signed-off-by: Ariel Elior <ariel.elior@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The acpi_node_get_property_reference() doesn't return ACPI error codes,
it just returns regular negative kernel error codes. This patch doesn't
affect run time, it's just a clean up.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Ruslan Babayev <ruslan@babayev.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current vsock code for removal of socket from the list is both
subject to race and inefficient. It takes the lock, checks whether
the socket is in the list, drops the lock and if the socket was on the
list, deletes it from the list. This is subject to race because as soon
as the lock is dropped once it is checked for presence, that condition
cannot be relied upon for any decision. It is also inefficient because
if the socket is present in the list, it takes the lock twice.
Signed-off-by: Sunil Muthuswamy <sunilmut@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Jakub Kicinski says:
====================
nfp: add two user friendly errors
This small series adds two error messages based on recent
bug reports which turned out not to be bugs..
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Users sometimes mistakenly try to manually bind the PF driver
to the VFs, print a warning message in that case.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Apparently there are still cards in the wild with a very old
management FW. Let's make the error message in that case
indicate more clearly that management firmware has to be
updated.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Robert Hancock says:
====================
Microchip KSZ driver enhancements
A couple of enhancements to the Microchip KSZ switch driver: one to add
PHY register settings for errata workarounds for more stable operation, and
another to add a device tree option to change the output clock rate as
required by some board designs.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The KSZ9477 series chips have a SYNCLKO pin which by default outputs a
25MHz clock, but some board setups require a 125MHz clock instead. Added
a microchip,synclko-125 device tree property to allow indicating a
125MHz clock output is required.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Silicon Errata and Data Sheet Clarification documents for the
KSZ9477 series of chips describe a number of otherwise undocumented PHY
register settings which are required to work around various chip errata.
Apply these settings when initializing the PHY ports on these chips.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If some of the switch ports were not listed in the device tree, due to
being unused, the ksz_mib_read_work function ended up accessing a NULL
dp->slave pointer and causing an oops. Skip checking statistics for any
unused ports.
Fixes: 7c6ff470aa867f53 ("net: dsa: microchip: add MIB counter reading support")
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Switch stmmac_mdio_reset to use GPIO descriptors. GPIO core handles the
"snps,reset-gpio" for GPIO descriptors so we don't need to take care of
it inside the driver anymore.
The advantage of this is that we now preserve the GPIO flags which are
passed via devicetree. This is required on some newer Amlogic boards
which use an Open Drain pin for the reset GPIO. This pin can only output
a LOW signal or switch to input mode but it cannot output a HIGH signal.
There are already devicetree bindings for these special cases and GPIO
core already takes care of them but only if we use GPIO descriptors
instead of GPIO numbers.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Reinhard Speyerer says:
====================
qmi_wwan: fix QMAP handling
This series addresses the following issues observed when using the
QMAP support of the qmi_wwan driver:
1. The QMAP code in the qmi_wwan driver is based on the CodeAurora
GobiNet driver ([1], [2]) which does not process QMAP padding
in the RX path correctly. This causes qmimux_rx_fixup() to pass
incorrect data to the IP stack when padding is used.
2. qmimux devices currently lack proper network device usage statistics.
3. RCU stalls on device disconnect with QMAP activated like this
# echo Y > /sys/class/net/wwan0/qmi/raw_ip
# echo 1 > /sys/class/net/wwan0/qmi/add_mux
# echo 2 > /sys/class/net/wwan0/qmi/add_mux
# echo 3 > /sys/class/net/wwan0/qmi/add_mux
have been observed in certain setups:
[ 2273.676593] option1 ttyUSB16: GSM modem (1-port) converter now disconnected from ttyUSB16
[ 2273.676617] option 6-1.2:1.0: device disconnected
[ 2273.676774] WARNING: CPU: 1 PID: 141 at kernel/rcu/tree_plugin.h:342 rcu_note_context_switch+0x2a/0x3d0
[ 2273.676776] Modules linked in: option qmi_wwan cdc_mbim cdc_ncm qcserial cdc_wdm usb_wwan sierra sierra_net usbnet mii edd coretemp iptable_mangle ip6_tables iptable_filter ip_tables cdc_acm dm_mod dax iTCO_wdt evdev iTCO_vendor_support sg ftdi_sio usbserial e1000e ptp pps_core i2c_i801 ehci_pci button lpc_ich i2c_core mfd_core uhci_hcd ehci_hcd rtc_cmos usbcore usb_common sd_mod fan ata_piix thermal
[ 2273.676817] CPU: 1 PID: 141 Comm: kworker/1:1 Not tainted 4.19.38-rsp-1 #1
[ 2273.676819] Hardware name: Not Applicable Not Applicable /CX-GS/GM45-GL40 , BIOS V1.11 03/23/2011
[ 2273.676828] Workqueue: usb_hub_wq hub_event [usbcore]
[ 2273.676832] EIP: rcu_note_context_switch+0x2a/0x3d0
[ 2273.676834] Code: 55 89 e5 57 56 89 c6 53 83 ec 14 89 45 f0 e8 5d ff ff ff 89 f0 64 8b 3d 24 a6 86 c0 84 c0 8b 87 04 02 00 00 75 7a 85 c0 7e 7a <0f> 0b 80 bf 08 02 00 00 00 0f 84 87 00 00 00 e8 b2 e2 ff ff bb dc
[ 2273.676836] EAX: 00000001 EBX: f614bc00 ECX: 00000001 EDX: c0715b81
[ 2273.676838] ESI: 00000000 EDI: f18beb40 EBP: f1a3dc20 ESP: f1a3dc00
[ 2273.676840] DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068 EFLAGS: 00010002
[ 2273.676842] CR0: 80050033 CR2: b7e97230 CR3: 2f9c4000 CR4: 000406b0
[ 2273.676843] Call Trace:
[ 2273.676847] ? preempt_count_add+0xa5/0xc0
[ 2273.676852] __schedule+0x4e/0x4f0
[ 2273.676855] ? __queue_work+0xf1/0x2a0
[ 2273.676858] ? _raw_spin_lock_irqsave+0x14/0x40
[ 2273.676860] ? preempt_count_add+0x52/0xc0
[ 2273.676862] schedule+0x33/0x80
[ 2273.676865] _synchronize_rcu_expedited+0x24e/0x280
[ 2273.676867] ? rcu_accelerate_cbs_unlocked+0x70/0x70
[ 2273.676871] ? wait_woken+0x70/0x70
[ 2273.676873] ? rcu_accelerate_cbs_unlocked+0x70/0x70
[ 2273.676875] ? _synchronize_rcu_expedited+0x280/0x280
[ 2273.676877] synchronize_rcu_expedited+0x22/0x30
[ 2273.676881] synchronize_net+0x25/0x30
[ 2273.676885] dev_deactivate_many+0x133/0x230
[ 2273.676887] ? preempt_count_add+0xa5/0xc0
[ 2273.676890] __dev_close_many+0x4d/0xc0
[ 2273.676892] ? skb_dequeue+0x40/0x50
[ 2273.676895] dev_close_many+0x5d/0xd0
[ 2273.676898] rollback_registered_many+0xbf/0x4c0
[ 2273.676901] ? raw_notifier_call_chain+0x1a/0x20
[ 2273.676904] ? call_netdevice_notifiers_info+0x23/0x60
[ 2273.676906] ? netdev_master_upper_dev_get+0xe/0x70
[ 2273.676908] rollback_registered+0x1f/0x30
[ 2273.676911] unregister_netdevice_queue+0x47/0xb0
[ 2273.676915] qmimux_unregister_device+0x1f/0x30 [qmi_wwan]
[ 2273.676917] qmi_wwan_disconnect+0x5d/0x90 [qmi_wwan]
...
[ 2273.677001] ---[ end trace 0fcc5f88496b485a ]---
[ 2294.679136] rcu: INFO: rcu_preempt detected stalls on CPUs/tasks:
[ 2294.679140] rcu: Tasks blocked on level-0 rcu_node (CPUs 0-1): P141
[ 2294.679144] rcu: (detected by 0, t=21002 jiffies, g=265857, q=8446)
[ 2294.679148] kworker/1:1 D 0 141 2 0x80000000
In addition the permitted QMAP mux_id value range is extended for
compatibility with ip(8) and the rmnet driver.
Reinhard
[1]: https://portland.source.codeaurora.org/patches/quic/gobi
[2]: https://portland.source.codeaurora.org/quic/qsdk/oss/lklm/gobinet/
====================
Tested-by: Daniele Palmas <dnlplm@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Permit mux_id values up to 254 to be used in qmimux_register_device()
for compatibility with ip(8) and the rmnet driver.
Fixes: c6adf77953bc ("net: usb: qmi_wwan: add qmap mux protocol support")
Cc: Daniele Palmas <dnlplm@gmail.com>
Signed-off-by: Reinhard Speyerer <rspmn@arcor.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Switch qmimux_unregister_device() and qmi_wwan_disconnect() to
use unregister_netdevice_queue() and unregister_netdevice_many()
instead of unregister_netdevice(). This avoids RCU stalls which
have been observed on device disconnect in certain setups otherwise.
Fixes: c6adf77953bc ("net: usb: qmi_wwan: add qmap mux protocol support")
Cc: Daniele Palmas <dnlplm@gmail.com>
Signed-off-by: Reinhard Speyerer <rspmn@arcor.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add proper network device usage statistics for qmimux devices
instead of reporting all-zero values for them.
Fixes: c6adf77953bc ("net: usb: qmi_wwan: add qmap mux protocol support")
Cc: Daniele Palmas <dnlplm@gmail.com>
Signed-off-by: Reinhard Speyerer <rspmn@arcor.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The QMAP code in the qmi_wwan driver is based on the CodeAurora GobiNet
driver which does not process QMAP padding in the RX path correctly.
Add support for QMAP padding to qmimux_rx_fixup() according to the
description of the rmnet driver.
Fixes: c6adf77953bc ("net: usb: qmi_wwan: add qmap mux protocol support")
Cc: Daniele Palmas <dnlplm@gmail.com>
Signed-off-by: Reinhard Speyerer <rspmn@arcor.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fix from James Bottomley:
"A single bug fix for hpsa.
The user visible consequences aren't clear, but the ioaccel2 raid
acceleration may misfire on the malformed request assuming the payload
is big enough to require chaining (more than 31 sg entries)"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: hpsa: correct ioaccel2 chaining
|
|
Eric Dumazet says:
====================
net/packet: better behavior under DDOS
Using tcpdump (or other af_packet user) on a busy host can lead to
catastrophic consequences, because suddenly, potentially all cpus
are spinning on a contended spinlock.
Both packet_rcv() and tpacket_rcv() grab the spinlock
to eventually find there is no room for an additional packet.
This patch series align packet_rcv() and tpacket_rcv() to both
check if the queue is full before grabbing the spinlock.
If the queue is full, they both increment a new atomic counter
placed on a separate cache line to let readers drain the queue faster.
There is still false sharing on this new atomic counter,
we might in the future make it per cpu if there is interest.
====================
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
