| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Since various MCI messages need to be
handled, along with driver-level support
in upper layers, disable AIC for now.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This patch adds support for post-processing
the AIC calibration results.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Set the appropriate bits in the HW after
AIC calibration is done.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This patch adds routines to handle the MCI
message AIC_CAL_SINGLE, starting the required
HW calibration.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Various registers to control and check AIC
status.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
AIC can be disabled or enabled on a per-card
basis using MCI configuration, so register a function
to check its status.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
These are necessary for implementing AIC,
supported by chips like WB222.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
emulate_write_cache is 0
A check that rejects a CDB with FUA bit set if no write cache is
emulated was added by the following commit:
fde9f50 target: Add sanity checks for DPO/FUA bit usage
The condition is as follows:
if (!dev->dev_attrib.emulate_fua_write ||
!dev->dev_attrib.emulate_write_cache)
However, this check is wrong if the backend device supports WCE but
"emulate_write_cache" is disabled.
This patch uses se_dev_check_wce() (previously named
spc_check_dev_wce) to invoke transport->get_write_cache() if the
device has a write cache or check the "emulate_write_cache" attribute
otherwise.
Reported-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Christophe Vu-Brugier <cvubrugier@fastmail.fm>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
This patch fixes a NULL pointer dereference triggered by a late
target_configure_device() -> alloc_workqueue() failure that results
in target_free_device() being called with DF_CONFIGURED already set,
which subsequently OOPses in destroy_workqueue() code.
Currently this only happens at modprobe target_core_mod time when
core_dev_setup_virtual_lun0() -> target_configure_device() fails,
and the explicit target_free_device() gets called.
To address this bug originally introduced by commit 0fd97ccf45, go
ahead and move DF_CONFIGURED to end of target_configure_device()
code to handle this special failure case.
Reported-by: Claudio Fleiner <cmf@daterainc.com>
Cc: Claudio Fleiner <cmf@daterainc.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: <stable@vger.kernel.org> # v3.7+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
This patch fixes a NULL pointer dereference OOPs with pSCSI backends
within target_core_stat.c code. The bug is caused by a configfs attr
read if no pscsi_dev_virt->pdv_sd has been configured.
Reported-by: Olaf Hering <olaf@aepfle.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
This patch adds a missing set of conditional check braces in
ft_invl_hw_context() originally introduced by commit dcd998ccd
when handling DDP failures in ft_recv_write_data() code.
commit dcd998ccdbf74a7d8fe0f0a44e85da1ed5975946
Author: Kiran Patil <kiran.patil@intel.com>
Date: Wed Aug 3 09:20:01 2011 +0000
tcm_fc: Handle DDP/SW fc_frame_payload_get failures in ft_recv_write_data
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Kiran Patil <kiran.patil@intel.com>
Cc: <stable@vger.kernel.org> # 3.1+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
This patch fixes a se_cmd->cmd_kref leak buf when se_sess->sess_tearing_down
is true within target_get_sess_cmd() submission path code.
This se_cmd reference leak can occur during active session shutdown when
ack_kref=1 is passed by target_submit_cmd_[map_sgls,tmr]() callers.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: <stable@vger.kernel.org> # 3.6+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
This patch changes loopback, usb-gadget, vhost-scsi and xen-scsiback
fabric code to invoke transport_register_session() instead of the
unprotected flavour, to ensure se_tpg->session_lock is taken when
adding new session list nodes to se_tpg->tpg_sess_list.
Note that since these four fabric drivers already hold their own
internal TPG mutexes when accessing se_tpg->tpg_sess_list, and
consist of a single se_session created through configfs attribute
access, no list corruption can currently occur.
So for correctness sake, go ahead and use the se_tpg->session_lock
protected version for these four fabric drivers.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
This patch fixes the incorrect use of __transport_register_session()
in tcm_qla2xxx_check_initiator_node_acl() code, that does not perform
explicit se_tpg->session_lock when accessing se_tpg->tpg_sess_list
to add new se_sess nodes.
Given that tcm_qla2xxx_check_initiator_node_acl() is not called with
qla_hw->hardware_lock held for all accesses of ->tpg_sess_list, the
code should be using transport_register_session() instead.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Giridhar Malavali <giridhar.malavali@qlogic.com>
Cc: Quinn Tran <quinn.tran@qlogic.com>
Cc: <stable@vger.kernel.org> # 3.5+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
This patch fixes a iser specific logout bug where early complete()
of conn->conn_logout_comp in iscsit_close_connection() was causing
isert_wait4logout() to complete too soon, triggering a use after
free NULL pointer dereference of iscsi_conn memory.
The complete() was originally added for traditional iscsi-target
when a ISCSI_LOGOUT_OP failed in iscsi_target_rx_opcode(), but given
iser-target does not wait in logout failure, this special case needs
to be avoided.
Reported-by: Sagi Grimberg <sagig@mellanox.com>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Slava Shwartsman <valyushash@gmail.com>
Cc: <stable@vger.kernel.org> # v3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
This reverts commit 72859d91d93319c00a18c29f577e56bf73a8654a.
The original patch was wrong, iscsit_close_connection() still needs
to release iscsi_conn during both normal + exception IN_LOGOUT status
with ib_isert enabled.
The original OOPs is due to completing conn_logout_comp early within
iscsit_close_connection(), causing isert_wait4logout() to complete
instead of waiting for iscsit_logout_post_handler_*() to be called.
Reported-by: Sagi Grimberg <sagig@mellanox.com>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Slava Shwartsman <valyushash@gmail.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Now that incoming FUA=1 bit check is enforced for backends with FUA or
WCE disabled, go ahead and disallow the changing of related backend
attributes when active fabric exports exist.
This is required to avoid potential failures with existing initiator
LUN registrations that have been previously created with FUA=1.
Reported-by: Christoph Hellwig <hch@lst.de>
Cc: Doug Gilbert <dgilbert@interlog.com>
Cc: James Bottomley <JBottomley@Parallels.com>
Cc: Ronnie Sahlberg <ronniesahlberg@gmail.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
With the increase in number of CPUs calls to functions that dump
output to console (e.g., arch_trigger_all_cpu_backtrace) can take
a long time to complete. If IRQs are disabled eventually the NMI
watchdog kicks in and creates more havoc. Avoid by telling the NMI
watchdog everything is ok.
Signed-off-by: David Ahern <david.ahern@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The M7 processor has a different hypervisor group id and different PCR fast
trap values. PIC read/write functions and PCR bit fields are the same as
the T4 so those are reused.
Signed-off-by: David Ahern <david.ahern@oracle.com>
Acked-by: Bob Picco <bob.picco@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently perf-stat (aka, counting mode) does not work:
$ perf stat ls
...
Performance counter stats for 'ls':
1.585665 task-clock (msec) # 0.580 CPUs utilized
24 context-switches # 0.015 M/sec
0 cpu-migrations # 0.000 K/sec
86 page-faults # 0.054 M/sec
<not supported> cycles
<not supported> stalled-cycles-frontend
<not supported> stalled-cycles-backend
<not supported> instructions
<not supported> branches
<not supported> branch-misses
0.002735100 seconds time elapsed
The reason is that state is never reset (stays with PERF_HES_UPTODATE set).
Add a call to sparc_pmu_enable_event during the added_event handling.
Clean up the encoding since pmu_start calls sparc_pmu_enable_event which
does the same. Passing PERF_EF_RELOAD to sparc_pmu_start means the call
to sparc_perf_event_set_period can be removed as well.
With this patch:
$ perf stat ls
...
Performance counter stats for 'ls':
1.552890 task-clock (msec) # 0.552 CPUs utilized
24 context-switches # 0.015 M/sec
0 cpu-migrations # 0.000 K/sec
86 page-faults # 0.055 M/sec
5,748,997 cycles # 3.702 GHz
<not supported> stalled-cycles-frontend:HG
<not supported> stalled-cycles-backend:HG
1,684,362 instructions:HG # 0.29 insns per cycle
295,133 branches:HG # 190.054 M/sec
28,007 branch-misses:HG # 9.49% of all branches
0.002815665 seconds time elapsed
Signed-off-by: David Ahern <david.ahern@oracle.com>
Acked-by: Bob Picco <bob.picco@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
perf_pmu_disable is called by core perf code before pmu->del and the
enable function is called by core perf code afterwards. No need to
call again within sparc_pmu_del.
Ditto for pmu->add and sparc_pmu_add.
Signed-off-by: David Ahern <david.ahern@oracle.com>
Acked-by: Bob Picco <bob.picco@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Round up min_size respectively round down max_size to the next power
of two to make sure we always respect the limit specified by the
user. This is required because we compare the table size against the
limit before we expand or shrink.
Also fixes a minor bug where we modified min_size in the params
provided instead of the copy stored in struct rhashtable.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input updates from Dmitry Torokhov:
"An update to Synaptics driver that makes it usable with the 2015
lineup from Lenovo"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Revert "Input: synaptics - use dmax in input_mt_assign_slots"
Input: synaptics - remove X250 from the topbuttonpad list
Input: synaptics - remove X1 Carbon 3rd gen from the topbuttonpad list
Input: synaptics - re-route tracksticks buttons on the Lenovo 2015 series
Input: synaptics - remove TOPBUTTONPAD property for Lenovos 2015
Input: synaptics - retrieve the extended capabilities in query $10
Input: synaptics - do not retrieve the board id on old firmwares
Input: synaptics - handle spurious release of trackstick buttons
Input: synaptics - fix middle button on Lenovo 2015 products
Input: synaptics - skip quirks when post-2013 dimensions
Input: synaptics - support min/max board id in min_max_pnpid_table
Input: synaptics - remove obsolete min/max quirk for X240
Input: synaptics - query min dimensions for fw v8.1
Input: synaptics - log queried and quirked dimension values
Input: synaptics - split synaptics_resolution(), query first
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse
Pull fuse fixes from Miklos Szeredi:
"This fixes bugs in zero-copy splice to the fuse device"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
fuse: explicitly set /dev/fuse file's private_data
fuse: set stolen page uptodate
fuse: notify: don't move pages
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/vfs
Pull overlayfs fixes from Miklos Szeredi:
"This fixes minor issues with the multi-layer update in v4.0"
* 'overlayfs-next' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/vfs:
ovl: upper fs should not be R/O
ovl: check lowerdir amount for non-upper mount
ovl: print error message for invalid mount options
|
|
Pull MMC fix from Ulf Hansson:
"MMC core: fix error path in mmc_pwrseq_simple_alloc()"
* tag 'mmc-v4.0-rc4' of git://git.linaro.org/people/ulf.hansson/mmc:
mmc: pwrseq_simple: fix error path in mmc_pwrseq_simple_alloc
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control fixes from Linus Walleij:
"Here is a slew of pin control fixes I've accumulated for the v4.0
kernel. Nothing special, just driver fixes (mainly embedded Intel it
seems) and a misunderstanding regarding the stub functions was
reverted:
- Fix up consumer return values on pin control stubs.
- Four patches fixing up the interrupt handling and sleep context
save in the Baytrail driver.
- Make default output directions work properly in the Cherryview
driver.
- Fix interrupt locking in the AT91 driver.
- Fix setting interrupt generating lines as input in the sunxi
driver"
* tag 'pinctrl-v4.0-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: sun4i: GPIOs configured as irq must be set to input before reading
pinctrl: at91: move lock/unlock_as_irq calls into request/release
pinctrl: update direction_output function of cherryview driver
pinctrl: baytrail: Save pin context over system sleep
pinctrl: baytrail: Rework interrupt handling
pinctrl: baytrail: Clear interrupt triggering from pins that are in GPIO mode
pinctrl: baytrail: Relax GPIO request rules
Revert "pinctrl: consumer: use correct retval for placeholder functions"
|
|
git://git.rocketboards.org/linux-socfpga-next
Pull two arch/nios2 fixes from Ley Foon Tan:
- Remove ucontext.h from exported arch headers
- nios2: mm: do not invoke OOM killer on kernel fault OOM
* tag 'nios2-fixes-v4.0-rc5' of git://git.rocketboards.org/linux-socfpga-next:
nios2: mm: do not invoke OOM killer on kernel fault OOM
nios2: Remove ucontext.h from exported arch headers
|
|
Quit complaining about a couple of events that we actually expect to see
during an NVM update.
Reported-by: Stefan Assmann <sassmann@redhat.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull IDE fix from David Miller:
"Just one fix to convert a by-hand conversion of jiffies to msecs, from
Nicholas McGuire"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/ide:
ide_tape: convert jiffies with jiffies_to_msecs
|
|
Pull sparc fixes from David Miller:
1) Some command cases of semtimedop() not even handled due to miscoded
comparison on sparc64. From Rob Gardner.
2) Due to two bugs, /proc/kcore wan't working properly on sparc.
3) Make sure fatal traps stop all running cpus, from Dave Kleikamp.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc: Fix /proc/kcore
sparc: semtimedop() unreachable due to comparison error
sparc: io_64.h: Replace io function-link macros
sparc64: fatal trap should stop all cpus
arch: sparc: kernel: starfire.c: Remove unused function
arch: sparc: kernel: traps_64.c: Remove some unused functions
|
|
We can't directly call ipv6_sock_mc_join() but should use the stub
instead and protect it around IS_ENABLED.
Fixes: d0f91938bede ("tipc: add ip/udp media type")
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Due to a merge error when creating c5c707f9 ("nfsd: implement pNFS
layout recalls"), we recursively call nfsd4_cb_layout_fail from itself,
leading to stack overflows.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Fixes: c5c707f9 ("nfsd: implement pNFS layout recalls")
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
---
fs/nfsd/nfs4layouts.c | 2 --
1 file changed, 2 deletions(-)
diff --git a/fs/nfsd/nfs4layouts.c b/fs/nfsd/nfs4layouts.c
index 3c1bfa1..1028a06 100644
--- a/fs/nfsd/nfs4layouts.c
+++ b/fs/nfsd/nfs4layouts.c
@@ -587,8 +587,6 @@ nfsd4_cb_layout_fail(struct nfs4_layout_stateid *ls)
rpc_ntop((struct sockaddr *)&clp->cl_addr, addr_str, sizeof(addr_str));
- nfsd4_cb_layout_fail(ls);
-
printk(KERN_WARNING
"nfsd: client %s failed to respond to layout recall. "
" Fencing..\n", addr_str);
--
1.9.1
|
|
Hariprasad Shenai says:
====================
Add Device ID and make device ID table const
This patch series adds new device ID and makes device ID table const
The patches series is created against 'net-next' tree.
And includes patches on cxgb4 and csiostor driver.
We have included all the maintainers of respective drivers. Kindly review the
change and let us know in case of any review comments.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make PCI Device ID Tables be "const" to move them out of the data segment and
remove a redundant check on CH_PCI_DEVICE_ID_TABLE_DEFINE_BEGIN in
t4_pci_id_tbl.h to guard the contents of the include file.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next
Johan Hedberg says:
====================
pull request: bluetooth-next 2015-03-19
This wont the last 4.1 bluetooth-next pull request, but we've piled up
enough patches in less than a week that I wanted to save you from a
single huge "last-minute" pull somewhere closer to the merge window.
The main changes are:
- Simultaneous LE & BR/EDR discovery support for HW that can do it
- Complete LE OOB pairing support
- More fine-grained mgmt-command access control (normal user can now do
harmless read-only operations).
- Added RF power amplifier support in cc2520 ieee802154 driver
- Some cleanups/fixes in ieee802154 code
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull networking fixes from David Miller:
1) Fix packet header offset calculation in _decode_session6(), from
Hajime Tazaki.
2) Fix route leak in error paths of xfrm_lookup(), from Huaibin Wang.
3) Be sure to clear state properly when scans fail in iwlwifi mvm code,
from Luciano Coelho.
4) iwlwifi tries to stop scans that aren't actually running, also from
Luciano Coelho.
5) mac80211 should drop mesh frames that are not encrypted, fix from
Bob Copeland.
6) Add new device ID to b43 wireless driver for BCM432228 chips, from
Rafał Miłecki.
7) Fix accidental addition of members after variable sized array in
struct tc_u_hnode, from WANG Cong.
8) Don't re-enable interrupts until after we call napi_complete() in
ibmveth and WIZnet drivers, frm Yongbae Park.
9) Fix regression in vlan tag handling of fec driver, from Fugang Duan.
10) If a network namespace change fails during rtnl_newlink(), we don't
unwind the device registry properly.
11) Fix two TCP regressions, from Neal Cardwell:
- Don't allow snd_cwnd_cnt to accumulate huge values due to missing
test in tcp_cong_avoid_ai().
- Restore CUBIC back to advancing cwnd by 1.5x packets per RTT.
12) Fix performance regression in xne-netback involving push TX
notifications, from David Vrabel.
13) __skb_tstamp_tx() can be called with a NULL sk pointer, do not
dereference blindly. From Willem de Bruijn.
14) Fix potential stack overflow in RDS protocol stack, from Arnd
Bergmann.
15) VXLAN_VID_MASK used incorrectly in new remote checksum offload
support of VXLAN driver. Fix from Alexey Kodanev.
16) Fix too small netlink SKB allocation in inet_diag layer, from Eric
Dumazet.
17) ieee80211_check_combinations() does not count interfaces correctly,
from Andrei Otcheretianski.
18) Hardware feature determination in bxn2x driver references a piece of
software state that actually isn't initialized yet, fix from Michal
Schmidt.
19) inet_csk_wait_for_connect() needs a sched_annotate_sleep()
annoation, from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (56 commits)
Revert "net: cx82310_eth: use common match macro"
net/mlx4_en: Set statistics bitmap at port init
IB/mlx4: Saturate RoCE port PMA counters in case of overflow
net/mlx4_en: Fix off-by-one in ethtool statistics display
IB/mlx4: Verify net device validity on port change event
act_bpf: allow non-default TC_ACT opcodes as BPF exec outcome
Revert "smc91x: retrieve IRQ and trigger flags in a modern way"
inet: Clean up inet_csk_wait_for_connect() vs. might_sleep()
ip6_tunnel: fix error code when tunnel exists
netdevice.h: fix ndo_bridge_* comments
bnx2x: fix encapsulation features on 57710/57711
mac80211: ignore CSA to same channel
nl80211: ignore HT/VHT capabilities without QoS/WMM
mac80211: ask for ECSA IE to be considered for beacon parse CRC
mac80211: count interfaces correctly for combination checks
isdn: icn: use strlcpy() when parsing setup options
rxrpc: bogus MSG_PEEK test in rxrpc_recvmsg()
caif: fix MSG_OOB test in caif_seqpkt_recvmsg()
bridge: reset bridge mtu after deleting an interface
can: kvaser_usb: Fix tx queue start/stop race conditions
...
|
|
Erik Hugne says:
====================
tipc: small bugfix an support for datagram connect()
Most notable in this series is patch#3 that allows programs to associate
a tipc address with a connectionless (RDM/DGRAM) socket.
v2: Fix indent issue in patch#3
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Following the example of ip4_datagram_connect, we store the
address in the socket structure for dgram/rdm sockets and use
that as the default destination for subsequent send() calls.
It is allowed to connect to any address types, and the behaviour
of send() will be the same as a normal sendto() with this address
provided. Binding to an AF_UNSPEC address clears the association.
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since commit 1186adf7df04 ("tipc: simplify message forwarding and
rejection in socket layer") -EHOSTUNREACH is propagated back to
the sending process if we fail to deliver the message to another
socket local to the node.
This is wrong, host unreachable should only be reported when the
destination port/name does not exist in the cluster, and that
check is always done before sending the message. Also, this
introduces inconsistent sendmsg() behavior for local/remote
destinations. Errors occurring on the receiving side should not
trickle up to the sender. If message delivery fails TIPC should
either discard the packet or reject it back to the sender based
on the destination droppable option.
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
tipc_node_remove_conn may be called twice if shutdown() is
called on a socket that have messages in the receive queue.
Calling this function twice does no harm, but is unnecessary
and we remove the redundant call.
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Nicolas Iooss <nicolas.iooss_linux@m4x.org>
Fixes: b6eea9ca354a ("mac802154: introduce driver-ops header")
Acked-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
The misc subsystem (which is used for /dev/fuse) initializes private_data to
point to the misc device when a driver has registered a custom open file
operation, and initializes it to NULL when a custom open file operation has
*not* been provided.
This subtle quirk is confusing, to the point where kernel code registers
*empty* file open operations to have private_data point to the misc device
structure. And it leads to bugs, where the addition or removal of a custom open
file operation surprisingly changes the initial contents of a file's
private_data structure.
So to simplify things in the misc subsystem, a patch [1] has been proposed to
*always* set the private_data to point to the misc device, instead of only
doing this when a custom open file operation has been registered.
But before this patch can be applied we need to modify drivers that make the
assumption that a misc device file's private_data is initialized to NULL
because they didn't register a custom open file operation, so they don't rely
on this assumption anymore. FUSE uses private_data to store the fuse_conn and
errors out if this is not initialized to NULL at mount time.
Hence, we now set a file's private_data to NULL explicitly, to be independent
of whatever value the misc subsystem initializes it to by default.
[1] https://lkml.org/lkml/2014/12/4/939
Reported-by: Giedrius Statkevicius <giedriuswork@gmail.com>
Reported-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Tom Van Braeckel <tomvanbraeckel@gmail.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
|
|
This reverts commit 2fa645cb2703d9b3786d850db815414dfeefa51d.
The assumption that at least 1 preferred console will be registered
when the stdout-path property is set is invalid, which can result
in _no_ consoles.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
Commit 106937e8ccdc ("of: fix handling of '/' in options for
of_find_node_by_path()") caused a regression in OF handling of
stdout-path. While it fixes some cases which have '/' after the ':', it
breaks cases where there is more than one '/' *before* the ':'.
For example, it breaks this boot string
stdout-path = "/rdb/serial@f040ab00:115200";
So rather than doing sequentialized checks (first for '/', then for ':';
or vice versa), to get the correct behavior we need to check for the
first occurrence of either one of them.
It so happens that the handy strcspn() helper can do just that.
Fixes: 106937e8ccdc ("of: fix handling of '/' in options for of_find_node_by_path()")
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: stable@vger.kernel.org # 3.19
Acked-by: Leif Lindholm <leif.lindholm@linaro.org>
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
There were regressions seen with commit 106937e8ccdc ("of: fix handling
of '/' in options for of_find_node_by_path()"), where we couldn't handle
extra '/' before the ':'. Let's test for this now.
Confirmed that this test fails without the previous patch and passes
when patched. All other tests pass.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Leif Lindholm <leif.lindholm@linaro.org>
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
The error code paths that require cleanup use a goto to jump to the
cleanup code and return an error code. However, the error code variable
res, which is initialized to -EINVAL when declared, is then overwritten
with the return value of of_parse_phandle_with_args(), and reused as the
return code from of_irq_parse_one(). This leads to an undetermined error
being returned instead of the expected -EINVAL value. Fix it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Cc: stable@vger.kernel.org # 3.13+
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
The current error-path code (when gpiod_get_index() reports
an error) can never free pwrseq->reset_gpios[0], but might
try to tree pwrseq->reset_gpios[-1], which has unfortunate
consequences.
Signed-off-by: NeilBrown <neil@brown.name>
Fixes: 934f1f48330ed695927a51fa068dc5d673f2da19
Acked-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reported-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
|
|
Since fab4085 ("netfilter: log: nf_log_packet() as real unified
interface"), the loginfo structure that is passed to nf_log_packet() is
used to explicitly indicate the logger type you want to use.
This is a problem for people tracing rules through nfnetlink_log since
packets are always routed to the NF_LOG_TYPE logger after the
aforementioned patch.
We can fix this by removing the trace loginfo structures, but that still
changes the log level from 4 to 5 for tracing messages and there may be
someone relying on this outthere. So let's just introduce a new
nf_log_trace() function that restores the former behaviour.
Reported-by: Markus Kötter <koetter@rrzn.uni-hannover.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
