| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
This document describes MQPRIO and CBS Qdisc offload configuration
for cpsw driver based on examples. It potentially can be used in
audio video bridging (AVB) and time sensitive networking (TSN).
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Need to restore shapers configuration after interface was down/up.
This is needed as appropriate configuration is still replicated in
kernel settings. This only shapers context restore, so vlan
configuration should be restored by user if needed, especially for
devices with one port where vlan frames are sent via ALE.
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The cpsw has up to 4 FIFOs per port and upper 3 FIFOs can feed rate
limited queue with shaping. In order to set and enable shaping for
those 3 FIFOs queues the network device with CBS qdisc attached is
needed. The CBS configuration is added for dual-emac/single port mode
only, but potentially can be used in switch mode also, based on
switchdev for instance.
Despite the FIFO shapers can work w/o cpdma level shapers the base
usage must be in combine with cpdma level shapers as described in TRM,
that are set as maximum rates for interface queues with sysfs.
One of the possible configuration with txq shapers and CBS shapers:
Configured with echo RATE >
/sys/class/net/eth0/queues/tx-0/tx_maxrate
/---------------------------------------------------
/
/ cpdma level shapers
+----+ +----+ +----+ +----+ +----+ +----+ +----+ +----+
| c7 | | c6 | | c5 | | c4 | | c3 | | c2 | | c1 | | c0 |
\ / \ / \ / \ / \ / \ / \ / \ /
\ / \ / \ / \ / \ / \ / \ / \ /
\/ \/ \/ \/ \/ \/ \/ \/
+---------|------|------|------|-------------------------------------+
| +----+ | | +---+ |
| | +----+ | | |
| v v v v |
| +----+ +----+ +----+ +----+ p p+----+ +----+ +----+ +----+ |
| | | | | | | | | o o| | | | | | | | |
| | f3 | | f2 | | f1 | | f0 | r CPSW r| f3 | | f2 | | f1 | | f0 | |
| | | | | | | | | t t| | | | | | | | |
| \ / \ / \ / \ / 0 1\ / \ / \ / \ / |
| \ X \ / \ / \ / \ / \ / \ / \ / |
| \/ \ \/ \/ \/ \/ \/ \/ \/ |
+-------\------------------------------------------------------------+
\
\ FIFO shaper, set with CBS offload added in this patch,
\ FIFO0 cannot be rate limited
------------------------------------------------------
CBS shaper configuration is supposed to be used with root MQPRIO Qdisc
offload allowing to add sk_prio->tc->txq maps that direct traffic to
appropriate tx queue and maps L2 priority to FIFO shaper.
The CBS shaper is intended to be used for AVB where L2 priority
(pcp field) is used to differentiate class of traffic. So additionally
vlan needs to be created with appropriate egress sk_prio->l2 prio map.
If CBS has several tx queues assigned to it, the sum of their
bandwidth has not overlap bandwidth set for CBS. It's recomended the
CBS bandwidth to be a little bit more.
The CBS shaper is configured with CBS qdisc offload interface using tc
tool from iproute2 packet.
For instance:
$ tc qdisc replace dev eth0 handle 100: parent root mqprio num_tc 3 \
map 2 2 1 0 2 2 2 2 2 2 2 2 2 2 2 2 queues 1@0 1@1 2@2 hw 1
$ tc -g class show dev eth0
+---(100:ffe2) mqprio
| +---(100:3) mqprio
| +---(100:4) mqprio
|
+---(100:ffe1) mqprio
| +---(100:2) mqprio
|
+---(100:ffe0) mqprio
+---(100:1) mqprio
$ tc qdisc add dev eth0 parent 100:1 cbs locredit -1440 \
hicredit 60 sendslope -960000 idleslope 40000 offload 1
$ tc qdisc add dev eth0 parent 100:2 cbs locredit -1470 \
hicredit 62 sendslope -980000 idleslope 20000 offload 1
The above code set CBS shapers for tc0 and tc1, for that txq0 and
txq1 is used. Pay attention, the real set bandwidth can differ a bit
due to discreteness of configuration parameters.
Here parameters like locredit, hicredit and sendslope are ignored
internally and are supposed to be set with assumption that maximum
frame size for frame - 1500.
It's supposed that interface speed is not changed while reconnection,
not always is true, so inform user in case speed of interface was
changed, as it can impact on dependent shapers configuration.
For more examples see Documentation.
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
That's possible to offload vlan to tc priority mapping with
assumption sk_prio == L2 prio.
Example:
$ ethtool -L eth0 rx 1 tx 4
$ qdisc replace dev eth0 handle 100: parent root mqprio num_tc 3 \
map 2 2 1 0 2 2 2 2 2 2 2 2 2 2 2 2 queues 1@0 1@1 2@2 hw 1
$ tc -g class show dev eth0
+---(100:ffe2) mqprio
| +---(100:3) mqprio
| +---(100:4) mqprio
|
+---(100:ffe1) mqprio
| +---(100:2) mqprio
|
+---(100:ffe0) mqprio
+---(100:1) mqprio
Here, 100:1 is txq0, 100:2 is txq1, 100:3 is txq2, 100:4 is txq3
txq0 belongs to tc0, txq1 to tc1, txq2 and txq3 to tc2
The offload part only maps L2 prio to classes of traffic, but not
to transmit queues, so to direct traffic to traffic class vlan has
to be created with appropriate egress map.
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
According to TRM tx rated channels should be in 7..0 order,
so correct it.
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The cpdma channel highest priority is from hi to lo number.
The driver has limited number of descriptors that are shared between
number of cpdma channels. Number of queues can be tuned with ethtool,
that allows to not spend descriptors on not needed cpdma channels.
In AVB usually only 2 tx queues can be enough with rate limitation.
The rate limitation can be used only for hi priority queues. Thus, to
use only 2 queues the 8 has to be created. It's wasteful.
So, in order to allow using only needed number of rate limited
tx queues, save resources, and be able to set rate limitation for
them, let assign tx cpdma channels in backward order to queues.
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5e-updates-2018-07-18
This series includes update for mlx5e net device driver.
1) From Feras Daoud, Added the support for firmware log tracing,
first by introducing the firmware API needed for the task and then
For each PF do the following:
1- Allocate memory for the tracer strings database and read it from the FW to the SW.
2- Allocate and dma map tracer buffers.
Traces that will be written into the buffer will be parsed as a group
of one or more traces, referred to as trace message. The trace message
represents a C-like printf string.
Once a new trace is available FW will generate an event indicates new trace/s are
available and the driver will parse them and dump them using tracepoints
event tracing
Enable mlx5 fw tracing by:
echo 1 > /sys/kernel/debug/tracing/events/mlx5/mlx5_fw/enable
Read traces by:
cat /sys/kernel/debug/tracing/trace
2) From Roi Dayan, Remove redundant WARN when we cannot find neigh entry
3) From Jianbo Liu, TC double vlan support
- Support offloading tc double vlan headers match
- Support offloading double vlan push/pop tc actions
4) From Boris, re-visit UDP GSO, remove the splitting of UDP_GSO_L4 packets
in the driver, and exposes UDP_GSO_L4 as a PARTIAL_GSO feature.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch removes the splitting of UDP_GSO_L4 packets in the driver,
and exposes UDP_GSO_L4 as a PARTIAL_GSO feature. Thus, the network stack
is not responsible for splitting the packet into two.
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
As we can configure two push/pop actions in one flow table entry,
add support to offload those double vlan actions in a rule to HW.
Signed-off-by: Jianbo Liu <jianbol@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Extract actions offloading code to a new function, and also extend data
structures for double vlan actions.
Signed-off-by: Jianbo Liu <jianbol@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
We can match on both outer and inner vlan tags, add support for
offloading that.
Signed-off-by: Jianbo Liu <jianbol@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
It is possible for neigh entry not to exist if it was cleaned already.
When we bring down an interface the neigh gets deleted but it could be
that our listener for neigh event to clear the encap valid bit didn't
start yet and the neigh update last used work is started first.
In this scenario the encap entry has valid bit set but the neigh entry
doesn't exist.
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Add the tracer file to the makefile and add the init
function to the load one flow.
Signed-off-by: Feras Daoud <ferasda@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
For each message the driver should do the following:
1- Find the message string in the strings database
2- Count the param number of each message
3- Wait for the param events and accumulate them
4- Calculate the event timestamp using the local event timestamp
and the first timestamp event following it.
5- Print message to trace log
Enable the tracing by:
echo 1 > /sys/kernel/debug/tracing/events/mlx5/mlx5_fw/enable
Read traces by:
cat /sys/kernel/debug/tracing/trace
Signed-off-by: Feras Daoud <ferasda@mellanox.com>
Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
The tracer has one event, event 0x26, with two subtypes:
- Subtype 0: Ownership change
- Subtype 1: Traces available
An ownership change occurs in the following cases:
1- Owner releases his ownership, in this case, an event will be
sent to inform others to reattempt acquire ownership.
2- Ownership was taken by a higher priority tool, in this case
the owner should understand that it lost ownership, and go through
tear down flow.
The second subtype indicates that there are traces in the trace buffer,
in this case, the driver polls the tracer buffer for new traces, parse
them and prepares the messages for printing.
The HW starts tracing from the first address in the tracer buffer.
Driver receives an event notifying that new trace block exists.
HW posts a timestamp event at the last 8B of every 256B block.
Comparing the timestamp to the last handled timestamp would indicate
that this is a new trace block. Once the new timestamp is detected,
the entire block is considered valid.
Block validation and parsing, should be done after copying the current
block to a different location, in order to avoid block overwritten
during processing.
Signed-off-by: Feras Daoud <ferasda@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Create a memory key and protection domain for the tracer log buffer.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
For each PF do the following:
1- Allocate memory for the tracer strings database and read the
strings from the FW to the SW. These strings will be used later for
parsing traces.
2- Allocate and dma map tracer buffers.
Traces that will be written into the buffer will be parsed as a group
of one or more traces, referred to as trace message. The trace message
represents a C-like printf string.
First trace of a message holds the pointer to the correct string in
strings database. The following traces holds the variables of the
message.
Signed-off-by: Feras Daoud <ferasda@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Implement FW tracer logic and registers access, initialization and
cleanup flows.
Initializing the tracer will be part of load one flow, as multiple
PFs will try to acquire ownership but only one will succeed and will
be the tracer owner.
Signed-off-by: Feras Daoud <ferasda@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux
mlx5 core infrastructure updates and fixes.
From Eran:
- Add MPEGC (Management PCIe General Configuration) registers and btis
- Fix tristate and description for MLX5 module
rom Feras:
- Add hardware structures for the firmware tracer
From Jainbo:
- Core support for double vlan push/pop steering action
From Max:
- Add XRQ commands definitions
From Noa:
- Add missing SET_DRIVER_VERSION command translation
From Roi:
- Use ERR_CAST() instead of coding it
From Tariq:
- Better return types for CQE API
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Bryan Whitehead says:
====================
lan743x: Add features to lan743x driver
This patch series adds extra features to the lan743x driver.
Updates for v4:
Patch 6/8 - Modified get/set_wol to use super set of
MAC and PHY driver support.
Patch 7/9 - In set_eee, return the return value from phy_ethtool_set_eee.
Updates for v3:
Removed patch 9 from this series, regarding PTP support
Patch 6/8 - Add call to phy_ethtool_get_wol to lan743x_ethtool_get_wol
Patch 7/8 - Add call to phy_ethtool_set_eee on (!eee->eee_enabled)
Updates for v2:
Patch 3/9 - Used ARRAY_SIZE macro in lan743x_ethtool_get_ethtool_stats.
Patch 5/9 - Used MAX_EEPROM_SIZE in lan743x_ethtool_set_eeprom.
Patch 6/9 - Removed unnecessary read of PMT_CTL.
Used CRC algorithm from lib.
Removed PHY interrupt settings from lan743x_pm_suspend
Change "#if CONFIG_PM" to "#ifdef CONFIG_PM"
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Implement RSS support
Signed-off-by: Bryan Whitehead <Bryan.Whitehead@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Implement EEE support
Signed-off-by: Bryan Whitehead <Bryan.Whitehead@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Implement power management
Supports suspend, resume, and Wake on LAN
Signed-off-by: Bryan Whitehead <Bryan.Whitehead@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Implement ethtool eeprom access
Also provides access to OTP (One Time Programming)
Signed-off-by: Bryan Whitehead <Bryan.Whitehead@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Implement ethtool message level
Signed-off-by: Bryan Whitehead <Bryan.Whitehead@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Implement ethtool statistics
Signed-off-by: Bryan Whitehead <Bryan.Whitehead@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use default link setting functions
Signed-off-by: Bryan Whitehead <Bryan.Whitehead@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Implement ethtool get_drvinfo
Signed-off-by: Bryan Whitehead <Bryan.Whitehead@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Sergei Shtylyov says:
====================
sh_eth: clean up the TSU register accessors
Here's a set of 5 patches against DaveM's 'net-next.git' repo. They do
a final clean up of the TSU register accessors...
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
sh_eth_tsu_read_entry() is still asymmetric with sh_eth_tsu_write_entry()
WRT their prototypes -- make them symmetric by passing to the former a TSU
register offset instead of its address and also adding the (now necessary)
'ndev' parameter...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We can add the TSU register base address to a TSU register offset right
in sh_eth_tsu_write_entry(), no need to do it in its callers...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With sh_eth_tsu_get_offset() now actually returning TSU register's offset,
we can at last use it in sh_eth_tsu_{read|write}(). Somehow this saves 248
bytes of object code with AArch64 gcc 4.8.5... :-)
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
sh_eth_tsu_get_offset(), despite its name, returns a TSU register's address,
not its offset. Make this function match its name and return a register's
offset from the TSU registers base address instead.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
sh_eth_tsu_get_offset() is called several times by the driver, remove
*inline* and move that function from the header to the driver itself
to let gcc decide whether to expand it inline or not...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
qe_muram_alloc return a unsigned long integer,which should not
compared with zero. check it using IS_ERR_VALUE() to fix this.
Fixes: c19b6d246a35 ("drivers/net: support hdlc function for QE-UCC")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Ursula Braun says:
====================
net/smc: patches 2018-07-23
here are some small patches for SMC: Just the first patch contains a
functional change. It allows to differ between the modes SMCR and SMCD
on s390 when monitoring SMC sockets. The remaining patches are cleanups
without functional changes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The page map address is already stored in the RMB descriptor.
There is no need to derive it from the cpu_addr value.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Link group field tokens_used_mask is a bitmap. Use macro
DECLARE_BITMAP for its definition.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace a frequently used construct with a more readable variant,
reducing the code. Also might come handy when we start to support
more than a single per link group.
Signed-off-by: Stefan Raspl <raspl@linux.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The functions to read and write cursors are exclusively used to copy
cursors. Therefore switch to a respective function instead.
Signed-off-by: Stefan Raspl <raspl@linux.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Rename field diag_fallback into diag_mode and set the smc mode of a
connection explicitly.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Support for device-only IPv6 multipath next hops was dropped in
commit 33bd5ac54dc4 ("net/ipv6: Revert attempt to simplify route replace
and append") and as of commit b5d2d75e079a ("net/ipv6: Do not allow
device only routes via the multipath API"), attempts to add a next hop
like that yield an explicit diagnostic.
Correspondingly, drop the IPv6 parts of GRE multipath test that are
supposed to test that code.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace calls to kmalloc followed by a memcpy with a direct call to
kmemdup.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Nikolay Aleksandrov says:
====================
net: bridge: add support for backup port
This set introduces a new bridge port option that allows any port to have
any other port (in the same bridge of course) as its backup and traffic
will be forwarded to the backup port when the primary goes down. This is
mainly used in MLAG and EVPN setups where we have peerlink path which is
a backup of many (or even all) ports and is a participating bridge port
itself. There's more detailed information in patch 02. Patch 01 just
prepares the port sysfs code for options that take raw value. The main
issues that this set solves are scalability and fallback latency.
We have used similar code for over 6 months now to bring the fallback
latency of the backup peerlink down and avoid fdb notification storms.
Also due to the nature of master devices such setup is currently not
possible, and last but not least having tens of thousands of fdbs require
thousands of calls to switch.
I've also CCed our MLAG experts that have been using similar option.
Roopa also adds:
"Two switches acting in a MLAG pair are connected by the peerlink
interface which is a bridge port.
the config on one of the switches looks like the below. The other
switch also has a similar config.
eth0 is connected to one port on the server. And the server is
connected to both switches.
br0 -- team0---eth0
|
-- switch-peerlink
switch-peerlink becomes the failover/backport port when say team0 to
the server goes down.
Today, when team0 goes down, control plane has to withdraw all the fdb
entries pointing to team0
and re-install the fdb entries pointing to switch-peerlink...and
restore the fdb entries when team0 comes back up again.
and this is the problem we are trying to solve.
This also becomes necessary when multihoming is implemented by a
standard like E-VPN https://tools.ietf.org/html/rfc8365#section-8
where the 'switch-peerlink' is an overlay vxlan port (like nikolay
mentions in his patch commit). In these implementations, the fdb scale
can be much larger.
On why bond failover cannot be used here ?: the point that nikolay was
alluding to is, switch-peerlink in the above example is a bridge port
and is a failover/backport port for more than one or all ports in the
bridge br0. And you cannot enslave switch-peerlink into a second level
team
with other bridge ports. Hence a multi layered team device is not an
option (FWIW, switch-peerlink is also a teamed interface to the peer
switch)."
v3: Added Roopa's explanation and diagram
v2: In patch 01 use kstrdup/kfree to avoid casting the const buf. In order
to avoid using GFP_ATOMIC or always allocating I kept the spinlock inside
each branch.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds a new port attribute - IFLA_BRPORT_BACKUP_PORT, which
allows to set a backup port to be used for known unicast traffic if the
port has gone carrier down. The backup pointer is rcu protected and set
only under RTNL, a counter is maintained so when deleting a port we know
how many other ports reference it as a backup and we remove it from all.
Also the pointer is in the first cache line which is hot at the time of
the check and thus in the common case we only add one more test.
The backup port will be used only for the non-flooding case since
it's a part of the bridge and the flooded packets will be forwarded to it
anyway. To remove the forwarding just send a 0/non-existing backup port.
This is used to avoid numerous scalability problems when using MLAG most
notably if we have thousands of fdbs one would need to change all of them
on port carrier going down which takes too long and causes a storm of fdb
notifications (and again when the port comes back up). In a Multi-chassis
Link Aggregation setup usually hosts are connected to two different
switches which act as a single logical switch. Those switches usually have
a control and backup link between them called peerlink which might be used
for communication in case a host loses connectivity to one of them.
We need a fast way to failover in case a host port goes down and currently
none of the solutions (like bond) cannot fulfill the requirements because
the participating ports are actually the "master" devices and must have the
same peerlink as their backup interface and at the same time all of them
must participate in the bridge device. As Roopa noted it's normal practice
in routing called fast re-route where a precalculated backup path is used
when the main one is down.
Another use case of this is with EVPN, having a single vxlan device which
is backup of every port. Due to the nature of master devices it's not
currently possible to use one device as a backup for many and still have
all of them participate in the bridge (which is master itself).
More detailed information about MLAG is available at the link below.
https://docs.cumulusnetworks.com/display/DOCS/Multi-Chassis+Link+Aggregation+-+MLAG
Further explanation and a diagram by Roopa:
Two switches acting in a MLAG pair are connected by the peerlink
interface which is a bridge port.
the config on one of the switches looks like the below. The other
switch also has a similar config.
eth0 is connected to one port on the server. And the server is
connected to both switches.
br0 -- team0---eth0
|
-- switch-peerlink
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds a new alternative store callback for port sysfs options
which takes a raw value (buf) and can use it directly. It is needed for the
backup port sysfs support since we have to pass the device by its name.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use dma_zalloc_coherent instead of dma_alloc_coherent
followed by memset 0.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After device is stopped we reset the rings by moving all free buffers
to positions [0, cnt - 2], and clear the position cnt - 1 in the ring.
We then proceed to clear the read/write pointers. This means that if
we try to reset the ring again the code will assume that the next to
fill buffer is at position 0 and swap it with cnt - 1. Since we
previously cleared position cnt - 1 it will lead to leaking the first
buffer and leaving ring in a bad state.
This scenario can only happen if FW communication fails, in which case
the ring will never be used again, so the fact it's in a bad state will
not be noticed. Buffer leak is the only problem. Don't try to move
buffers in the ring if the read/write pointers indicate the ring was
never used or have already been reset.
nfp_net_clear_config_and_disable() is now fully idempotent.
Found by code inspection, FW communication failures are very rare,
and reconfiguring a live device is not common either, so it's unlikely
anyone has ever noticed the leak.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that we have offload replay infrastructure added by
commit 326367427cc0 ("net: sched: call reoffload op on block callback reg")
and flows are guaranteed to be removed correctly, we can revert
commit 951a8ee6def3 ("nfp: reject binding to shared blocks").
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
