summaryrefslogtreecommitdiff
AgeCommit message (Collapse)AuthorFilesLines
2015-06-15Merge ath-next from ath.gitKalle Valo21-209/+326
Major changes: wil6210: * add modparam for bcast ring size * support hidden SSID * add per-MCS Rx stats
2015-06-15rt2800: fix assigning same WCID for different stationsStanislaw Gruszka3-55/+28
On some hardware reading WCID entries table results getting 0xff numbers, no matter of value written there before. This cause assigning the same WCID for different stations and makes not possible to connect to more than one station. Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-06-15brcmfmac: assure p2pdev is unregistered upon driver unloadArend van Spriel3-5/+6
When unloading the driver with a p2pdev interface it resulted in a warning upon calling wiphy_unregister() and subsequently a crash in the driver. This patch assures the p2pdev is unregistered calling unregister_wdev() before doing the wiphy_unregister(). Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-06-15brcmfmac: move p2p attach/detach functionsArend van Spriel1-99/+99
Moving two functions in p2p.c as is so next change will be easier to review. Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-06-15brcmfmac: free ifp for non-netdev interface in p2p moduleArend van Spriel2-2/+3
Making it more clear by freeing the ifp in same place where the vif object is freed. Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-06-15brcmfmac: have sdio return -EIO when device communication is not possibleArend van Spriel2-0/+7
The bus interface functions txctl and rxctl may be used while the device can not be accessed, eg. upon driver .remove() callback. This patch will immediately return -EIO when this is the case which speeds up the module unload. Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-06-15brcmfmac: rework .get_station() callbackArend van Spriel2-92/+161
The .get_station() cfg80211 callback is used in several scenarios. In managed mode it can obtain information about the access-point and its BSS parameters. In managed mode it can also obtain information about TDLS peers. In AP mode it can obtain information about connected clients. Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com> Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-06-15brcmfmac: Build wiphy mode and interface combinations dynamicallyPontus Fuchs1-68/+68
Switch from using semi hard coded interface combinations. This makes it easier to announce what the firmware actually supports. This fixes the case where brcmfmac announces p2p but the firmware doesn't support it. Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Reviewed-by: Arend Van Spriel <arend@broadcom.com> Signed-off-by: Pontus Fuchs <pontusf@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-06-15brcmfmac: Check if firmware supports p2pPontus Fuchs2-1/+4
Add a feature flag to reflect the firmware's p2p capability. Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Reviewed-by: Arend Van Spriel <arend@broadcom.com> Signed-off-by: Pontus Fuchs <pontusf@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-06-15mt7601u: don't warn about devices without per-rate power tableJakub Kicinski1-0/+4
We expect EEPROM per-rate power table to be filled with s6 values and warn user if values are invalid. However, there appear to be devices which don't have this section of EEPROM initialized. In such case we should ignore the values and leave the driver power tables set to zero. Note that vendor driver doesn't care about this case but mt76x2 skips 0xff per value. We take mt76x2's approach. Signed-off-by: Jakub Kicinski <kubakici@wp.pl> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-06-15MAINTAINERS: remove rt2x00.serialmonkey.com list and web pageStanislaw Gruszka1-2/+0
rt2x00.serialmonkey.com will be shutdown. Since traffic on rt2x00 mailing list is very low, we can use only linux-wireless list for any rt2x00 related topics. Thanks for Luis Correia, Ivo van Doorn and Mark Wallis for maintaining rt2x00 servers for years! Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-06-15mwifiex: handle BT coex event to adjust Rx BA window sizeChunfan Chen7-2/+277
If timeshare coexistance between bluetooth and WLAN gets enabled, firmware will give host an event to reduce Rx AMPDU BA window size. The event is handled in this patch. Signed-off-by: Chunfan Chen <jeffc@marvell.com> Signed-off-by: Cathy Luo <cluo@marvell.com> Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-06-15ath9k_htc: add support of channel switchChun-Yeow Yeoh4-1/+40
Add the support of channel switching functionality, similar to ath9k support. Tested with TP-Link TL-WN722N and TL-WN821N. Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-06-15brcmfmac: use debugfs_create_devm_seqfile() helper functionArend van Spriel1-36/+4
Some time ago the function debugfs_create_devm_seqfile() was introduced in debugfs. The caller simply needs to provide a device pointer and read function. The function brcmf_debugfs_add_entry() is now simply a wrapper only doing the work for CONFIG_BRCMDBG. Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com> Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-06-15brcmfmac: remove watchdog reset from brcmf_pcie_buscoreprep()Arend van Spriel1-14/+2
The watchdog reset as done in brcmf_pcie_buscoreprep() is not sufficient. It needs to modify PCIe core registers as well which is properly done by brcmf_pcie_reset_device() after the chip recognition is done. So the faulty watchdog reset can be removed as it was causing driver reload to fail and hang the system requiring a power-cycle. Instead the call to to the brcmf_pcie_reset_device() function is done twice in the unload. Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com> Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-06-15brcmfmac: remove chipinfo debugfs entryArend van Spriel1-10/+0
The information provided by chipinfo is also provided by the revinfo debugfs entry. Removing it from debugfs. Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-06-15brcmfmac: Update msgbuf read pointer quicker.Hante Meuleman3-13/+21
On device to host data using msgbuf the read pointer gets updated once all data is processed. Updating this pointer more frequently allows the firmware to add more data quicker. This will result in slightly higher and more stable throughput on CPU bounded host processors. Reviewed-by: Arend Van Spriel <arend@broadcom.com> Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Hante Meuleman <meuleman@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-06-15rtlwifi: rtl8192c: Add init codes for "fw_version" and "fw_subversion".Taehee Yoo1-1/+2
The variable "fw_version" is used in the _ResetDigitalProcedure1(). but It is not initialized. so I add init codes for "fw_version" and "fw_subversion". Signed-off-by: Taehee Yoo <ap420073@gmail.com> Acked-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-06-15rtlwifi: rtl8192cu: Fix variable isfirst_ampduTaehee Yoo1-1/+1
rtl92cu_rx_query_desc set a isampdu twice. but second code is related to isfirst_ampdu. so i change it. Signed-off-by: Taehee Yoo <ap420073@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-06-15rtlwifi: rtl8192cu: debug message change "RTL8192CE" to "RTL8192CU"Taehee Yoo1-5/+5
In the rtlwifi/rtl8192cu, I change debug message "RTL8192CE" to "RTL8192CU". Signed-off-by: Taehee Yoo <ap420073@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-06-15rtlwifi: rtl8192cu: remove duplicated routine in ↵Taehee Yoo1-4/+0
_rtl92c_phy_rf6052_config_parafile in the _rtl92c_phy_rf6052_config_parafile(), cases RF90_PATH_A and RF90_PATH_B call the same routine. so i remove one of these routine. also the return routine is duplicated. so i remove it. Signed-off-by: Taehee Yoo <ap420073@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-06-15rtlwifi: fix tm_trigger usageHans Ulli Kroll7-29/+21
While working on getting my rtl8821au driver in pretty shape for inclusion, it is dicosvered that the tm_trigger flag is used only for the first device using this driver. This flag handles the thermal power management in the hardware. To change this add a entry in sttruct rtl_dm, so each device can handle is separately. Signed-off-by: Hans Ulli Kroll <ulli.kroll@googlemail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-06-15rtlwifi: rtl8192cu: remove INTF_PCI and INTF_USBTaehee Yoo1-14/+4
in the rtlwifi/rtl8192cu, INTF_PCI and INTF_USB is unnecessary. because RTL8192CU chipset is only USB interface. Signed-off-by: Taehee Yoo <ap420073@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-06-15rtlwifi: rtl8192cu: remove _InitBeaconParameters().Taehee Yoo3-39/+22
_InitBeaconParameters() and rtl92cu_init_beacon_parameters() is same routine. I remove both functions. then i add _rtl92cu_init_beacon_parameters() in the hw.c. _rtl92cu_init_beacon_parameters() is same routine with _InitBeaconParameters(). Signed-off-by: Taehee Yoo <ap420073@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-06-15rtlwifi: rtl8192cu: remove IS_HARDWARE_TYPE_8192CE and IS_HARDWARE_TYPE_8192CUTaehee Yoo1-15/+3
in the rtlwifi/rtl8192cu, IS_HARDWARE_TYPE_8192CE and IS_HARDWARE_TYPE_8192CU is unnecessary. because rtlwifi/rtl8192cu codes aren't shared. Signed-off-by: Taehee Yoo <ap420073@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-06-09wil6210: reorder init sequenceVladimir Kondratiev4-39/+48
Need to reorder init sequence to run wil_platform_init before pci_enable_device. Assumption is platform init may be required before device may be enabled. Another issue, platform uninit should be called after pci_disable_device because platform uninit may render pci device non-accessible. Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2015-06-09wil6210: platform hooks for modile init/exitVladimir Kondratiev3-1/+33
Provide platform hooks for module init/exit. If platform require to perform some specific actions in global context, this is where to do so. Example may be turning on power for the PCIE based on DT information. Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2015-06-09wil6210: Support hidden SSIDHamad Kadmany4-6/+57
Pass hidden SSID information to FW for proper operation. In order to be able to scan/connect to the hidden SSID, SSID setting is added when scan is requested from FW. SSID scanning currently supports single SSID due to FW limitation. Signed-off-by: Hamad Kadmany <qca_hkadmany@qca.qualcomm.com> Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2015-06-09wil6210: add per-MCS Rx statsVladimir Kondratiev3-1/+11
Provide detailed statistics for the Rx frames per MCS Statistics printed in "stations" debugfs entry Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2015-06-09wil6210: add NIC memory region mac_rgf_extVladimir Kondratiev2-1/+2
Firmware defines new memory region, mac_rgf_ext that need to be accessed from the host for debug purposes. Add corresponded mapping Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2015-06-09wil6210: modparam for bcast ring sizeVladimir Kondratiev1-0/+2
Control Bcast ring size in similar way as Rx and Tx ones, through "bcast_ring_order" modparam, actual ring size is 1 << order Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2015-06-09ath6kl: Fix multiple clients associating in AP modeBrent Taylor1-1/+1
When one client is associated and connected to an ar6003 hw version 2.0 with firmware 3.1.1.149, and another client tries to connect, the first client's MAC address is lost in the station list because the "aid" is always "1". The structure "wmi_connect_event" has the "aid" as the second byte in the message, but it should be the first byte. This patch has been tested with linux-3.10.40 Signed-off-by: Brent Taylor <motobud@gmail.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2015-06-09ath10k: prevent memory leak in wmi rx opsMichal Kazior2-4/+7
Found during code review. This was pretty much impossible to happen but better safe than sorry. Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2015-06-09ath10k: fix channel switchingMichal Kazior1-80/+62
In the midst of chanctx patch review channel switching became broken which I failed to notice until now. Function ath10k_mac_vif_chan() reports current chandef which isn't updated until after switch_vif_chanctx() is returned from. Consequently the driver just restarted operation on channels it was residing already instead of switching to the new ones. Fixes: 500ff9f9389d ("ath10k: implement chanctx API") Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2015-06-09ath10k: remove ath10k_chanctx structMichal Kazior2-56/+6
In practice there's no point in having a copy of chanctx_conf. Most of the time the channel pointer (and band along with it) is accessed and this can't change after a chanctx is created because switching is done using explicit chanctx swapping via switch_vif_chanctx(). The only thing that can change within a chanctx_conf and is used by the driver is radar_enabled and channel width. These are however always accessed in adequate mac80211 callback context which guarantees safe access to the chanctx data. Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2015-06-09ath10k: fix ar->rx_channel updating logicMichal Kazior1-5/+17
Channel contexts aren't iterable until after they've been added to the driver. The code assumed otherwise. This problem could result in: * rx_channel being NULL and forcing Rx path to go the slow way to get channel on QCA988X, * report incorrect channel when running multi-channel on QCA61X4 hw2.1, * report incorrect channel after AP channel switch. Fixes: 500ff9f9389d ("ath10k: implement chanctx API") Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2015-06-09ath10k: remove unused variable 'id' in ath10k_pci_tx_pipe_cleanup()Raja Mani1-3/+0
mete_data is extracted from ce descriptor and stored in variable 'id'. later, id is not used anywhere in the same function. Fixes: d84a512dca23 ("ath10k: remove transfer_id from ath10k_hif_cb::tx_completion") Signed-off-by: Raja Mani <rmani@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2015-06-09ath10k: free wmi mgmt event skb when parsing failsRaja Mani1-0/+1
When wmi mgmt event function fails to parse given skb, it should be freed on failure condition to avoid memory leaks. Found this during the code review. Signed-off-by: Raja Mani <rmani@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2015-06-08bcma: lower dependency of BCMA_DRIVER_PCI_HOSTMODERafał Miłecki1-6/+6
This extension of BCMA_DRIVER_PCI has no reason to depend on BCMA_HOST_PCI. User may just want to have PCI device attached to SoC registered without enabling any extra client mode code. This can be useful when having non-bcma PCI device attached or when using other PCI driver. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-06-08bcma: make calls to PCI hostmode functions config-safeRafał Miłecki1-0/+11
Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-06-08b43: fix support for 14e4:4321 PCI dev with BCM4321 chipsetRafał Miłecki1-0/+4
It seems Broadcom released two devices with conflicting device id. There are for sure 14e4:4321 PCI devices with BCM4321 (N-PHY) chipset, they can be found in routers, e.g. Netgear WNR834Bv2. However, according to Broadcom public sources 0x4321 is also used for 5 GHz BCM4306 (G-PHY). It's unsure if they meant PCI device id, or "virtual" id (from SPROM). To distinguish these devices lets check PHY type (G vs. N). Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Cc: <stable@vger.kernel.org> # 3.16+ Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-06-08brcmfmac: use direct data pointer in NVRAM parser structRafał Miłecki1-20/+20
As we plan to add support for platform NVRAM we should store direct data pointer without the extra struct firmware layer. This will allow us to support other sources with the only requirement being u8 buffer. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Acked-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-06-08mt7601u: set promiscous mode based on FIF_OTHER_BSSJakub Kicinski1-0/+1
Most drivers use FIF_OTHER_BSS to set promiscous mode. Let us follow their lead even though it doesn't match exactly the HW filter flags. Signed-off-by: Jakub Kicinski <kubakici@wp.pl> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-06-08mt7601u: don't cleanup device second time after .resume()Jakub Kicinski2-1/+11
Make sure .disconnect() doesn't cleanup the device if .resume() failed. This may happen when device is removed during suspend. Signed-off-by: Jakub Kicinski <kubakici@wp.pl> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-06-08mt7601u: watch out for invalid-length framesJakub Kicinski2-4/+18
Users of older Ralink devices report that received frames sometimes have zero length. Watch out for that. Signed-off-by: Jakub Kicinski <kubakici@wp.pl> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-06-08mt7601u: unify paged and non-paged RX dma pathsJakub Kicinski1-50/+12
Signed-off-by: Jakub Kicinski <kubakici@wp.pl> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-06-08brcmfmac: set wiphy perm_addr to hardware MAC addressRafał Miłecki1-0/+1
This allows e.g. user space to use /sys/class/ieee80211/*/macaddress Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-06-08brcmfmac: support NVRAMs containing pci devpaths (instead of pcie)Rafał Miłecki1-2/+8
Recently Broadcom added support for NVRAMs with entries for multiple PCIe devices. One of the supported formats is based on prefixes defined like: devpath0=pcie/1/4/ and entries like 0:foo=bar 0:baz=qux etc. Unfortunately there are also a bit older devices using different way of defining prefixes, e.g. SmartRG SR400ac (2 x BCM43602) with entries: devpath0=pci/1/1/ devpath1=pci/2/1 Broadcom stated this old format will never be used/supported by brcmfmac but given the simplicity of this patch I'll insist on supporting it. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-06-08mwifiex: update current config_band info in start_apAvinash Patil1-0/+2
It was observed that AP beacons would not reflect correct regulatory information upon starting AP in A band. This was because of missing AP config band update in set_channel of start_ap. Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-06-08mwifiex: change debug dump issue since skb maybe nullZhaoyang Liu1-1/+2
This patch fixes semantic warning for debugging data dump feature. Previous code is based on the assumption that skb is not null. New change makes sure that we already have data buffer. Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Zhaoyang Liu <liuzy@marvell.com> Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
generated by cgit v1.2.3 (git 2.39.0) at 2025-01-07 00:30:39 +0300