summaryrefslogtreecommitdiff
AgeCommit message (Collapse)AuthorFilesLines
2014-10-02wil6210: atomic I/O for the card memoryVladimir Kondratiev6-0/+276
Introduce netdev IOCTLs, to be used by the debug tools. Allows to read/write single dword value or memory block, aligned to dword Different address modes supported: - BAR offset - Firmware "linker" address - target's AHB bus Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-10-02wil6210: manual FW error recovery modeVladimir Kondratiev5-9/+121
Introduce manual FW recovery mode. It is activated if module parameter @no_fw_recovery set to true. May be changed at runtime. Recovery information provided by new "recovery" debugfs file. It prints: mode = [auto|manual] state = [idle|pending|running] In manual mode, after FW error, recovery won't start automatically. Instead, after notification to user space, recovery waits in "pending" state, as indicated by the "recovery" debugfs file. User space tools may perform data collection and allow to continue recovery by writing "run" to the "recovery" debugfs file. Alternatively, recovery pending may be canceled by stopping network interface i.e. 'ifconfig wlan0 down' Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-10-02ath: Add support for tracingSujith Manoharan6-0/+107
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-10-02Merge branch 'for-upstream' of ↵John W. Linville5-63/+139
git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next
2014-10-02Bluetooth: 6lowpan: Check transmit errors for multicast packetsJukka Rissanen1-3/+10
We did not return error if multicast packet transmit failed. This might not be desired so return error also in this case. If there are multiple 6lowpan devices where the multicast packet is sent, then return error even if sending to only one of them fails. Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2014-10-02Bluetooth: 6lowpan: Return EAGAIN error also for multicast packetsJukka Rissanen1-11/+5
Make sure that we are able to return EAGAIN from l2cap_chan_send() even for multicast packets. The error code was ignored unncessarily. Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2014-10-02Bluetooth: 6lowpan: Avoid memory leak if memory allocation failsJukka Rissanen1-2/+6
If skb_unshare() returns NULL, then we leak the original skb. Solution is to use temp variable to hold the new skb. Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2014-10-02Bluetooth: 6lowpan: Memory leak as the skb is not freedJukka Rissanen1-0/+2
The earlier multicast commit 36b3dd250dde ("Bluetooth: 6lowpan: Ensure header compression does not corrupt IPv6 header") lost one skb free which then caused memory leak. Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2014-10-02Bluetooth: Fix lockdep warning with l2cap_chan_connectJohan Hedberg1-5/+8
The L2CAP connection's channel list lock (conn->chan_lock) must never be taken while already holding a channel lock (chan->lock) in order to avoid lock-inversion and lockdep warnings. So far the l2cap_chan_connect function has acquired the chan->lock early in the function and then later called l2cap_chan_add(conn, chan) which will try to take the conn->chan_lock. This violates the correct order of taking the locks and may lead to the following type of lockdep warnings: -> #1 (&conn->chan_lock){+.+...}: [<c109324d>] lock_acquire+0x9d/0x140 [<c188459c>] mutex_lock_nested+0x6c/0x420 [<d0aab48e>] l2cap_chan_add+0x1e/0x40 [bluetooth] [<d0aac618>] l2cap_chan_connect+0x348/0x8f0 [bluetooth] [<d0cc9a91>] lowpan_control_write+0x221/0x2d0 [bluetooth_6lowpan] -> #0 (&chan->lock){+.+.+.}: [<c10928d8>] __lock_acquire+0x1a18/0x1d20 [<c109324d>] lock_acquire+0x9d/0x140 [<c188459c>] mutex_lock_nested+0x6c/0x420 [<d0ab05fd>] l2cap_connect_cfm+0x1dd/0x3f0 [bluetooth] [<d0a909c4>] hci_le_meta_evt+0x11a4/0x1260 [bluetooth] [<d0a910eb>] hci_event_packet+0x3ab/0x3120 [bluetooth] [<d0a7cb08>] hci_rx_work+0x208/0x4a0 [bluetooth] CPU0 CPU1 ---- ---- lock(&conn->chan_lock); lock(&chan->lock); lock(&conn->chan_lock); lock(&chan->lock); Before calling l2cap_chan_add() the channel is not part of the conn->chan_l list, and can therefore only be accessed by the L2CAP user (such as l2cap_sock.c). We can therefore assume that it is the responsibility of the user to handle mutual exclusion until this point (which we can see is already true in l2cap_sock.c by it in many places touching chan members without holding chan->lock). Since the hci_conn and by exctension l2cap_conn creation in the l2cap_chan_connect() function depend on chan details we cannot simply add a mutex_lock(&conn->chan_lock) in the beginning of the function (since the conn object doesn't yet exist there). What we can do however is move the chan->lock taking later into the function where we already have the conn object and can that way take conn->chan_lock first. This patch implements the above strategy and does some other necessary changes such as using __l2cap_chan_add() which assumes conn->chan_lock is held, as well as adding a second needed label so the unlocking happens as it should. Reported-by: Jukka Rissanen <jukka.rissanen@linux.intel.com> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Tested-by: Jukka Rissanen <jukka.rissanen@linux.intel.com> Acked-by: Jukka Rissanen <jukka.rissanen@linux.intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2014-09-30rtlwifi: Fix randconfig build error with next-20140930Larry Finger1-1/+2
Configuration randconfig-1412075201 gets an error because driver rtl8821ae depends on driver btcoexist, but Kconfig does not select it. Reported-by: Jim Davis <jim.epost@gmail.com> Cc: Jim Davis <jim.epost@gmail.com> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-09-30mwifiex: add client mac address while configuring keys on GO.Maithili Hinge1-1/+1
When mwifiex device becomes GO, unicast traffic between client1 and GO stops when client2 connects to GO. Reason behind this was PTK getting overwritten by key_material command for client2 as it did not have client mac address. So, client1 can no more decode GO's ping packets though it responds to its broadcast packets. This patch adds case to check for BSS_ROLE instead of bss_type to set client mac address while configuring keys when device becomes GO. Signed-off-by: Maithili Hinge <maithili@marvell.com> Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Cathy Luo <cluo@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-09-30ath9k: fix getting tx duration for dynackFelix Fietkau7-18/+49
On AR9003, tx control and tx status are in separate descriptor rings. Tx duration is extracted from the tx control descriptor data, which ar9003_hw_proc_txdesc cannot access. Fix getting the duration by adding a separate callback for it. Acked-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com> Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-09-30ath9k: Check early for HW resetSujith Manoharan1-4/+6
chan_lock is not required for checking if we are in the middle of a HW reset, so do it early. This also removes the small window where the lock is dropped and reacquired. Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-09-30brcmfmac: Add wowl support for PCIE devices.Hante Meuleman8-41/+220
Add basic wowl (magic packet and disconnect) support. This patch adds this support only for PCIE bus devices. This feature requires FW which has support for wowl built in. Reviewed-by: Arend Van Spriel <arend@broadcom.com> Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com> Signed-off-by: Hante Meuleman <meuleman@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-09-30brcmfmac: Fix crash on cleanup.Hante Meuleman1-1/+1
When driver gets unloaded due to error situation there is a chance a packet gets received while fws has already been cleaned up. This will result in kernel crash. This patch adds a check to avoid this crash. Reviewed-by: Arend Van Spriel <arend@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Hante Meuleman <meuleman@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-09-30brcmfmac: assure P2P discovery is disabled when setting P2P_DEVICE mac addressArend van Spriel1-1/+4
In order to provision the P2P_DEVICE mac address using p2p_da_override iovar the discovery interface must be disabled. On some targets setting the mac address failed so disable the discovery interface to be certain. Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com> Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-09-30brcmfmac: Avoid usage of GFP_ATOMIC.Hante Meuleman2-24/+108
Msgbuf is using GFP_ATOMIC where GFP_KERNEL is also sufficient. On some platforms the coherent DMA memory is very limited when using GFP_ATOMIC. This patch changes usage of GFP_ATOMIC to GFP_KERNEL and uses worker to make this possible for creation of flowring. Reviewed-by: Arend Van Spriel <arend@broadcom.com> Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com> Signed-off-by: Hante Meuleman <meuleman@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-09-30brcmfmac: Fix sign issue with IOCTL return code in msgbuf.Hante Meuleman1-2/+3
Need a cast to assure correct value is propagated. Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com> Signed-off-by: Hante Meuleman <meuleman@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-09-30brcmfmac: On scan timeout do send received results.Hante Meuleman2-7/+4
Increase driver scan timeout from 8 to 10 seconds and report results to cfg80211. Without this patch the already received results were dropped on driver timeout. Reviewed-by: Arend Van Spriel <arend@broadcom.com> Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com> Signed-off-by: Hante Meuleman <meuleman@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-09-30ath9k_hw: fix PLL clock initialization for newer SoCFelix Fietkau3-4/+40
On AR934x and newer SoC devices, the layout of the AR_RTC_PLL_CONTROL register changed. This currently breaks at least 5/10 MHz operation. AR933x uses the old layout. It might also have been causing other stability issues because of the different location of the PLL_BYPASS bit which needs to be set during PLL clock initialization. This patch also removes more instances of hardcoded register values in favor of properly computed ones with the PLL_BYPASS bit added. Reported-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com> Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-09-30ath9k_hw: reduce ANI spur immunity setting on HT40 extension channelFelix Fietkau1-3/+2
The cycpwr_thr1 value needs to be lower on the extension channel than on the control channel, similar to how the register settings are programmed in the initvals. Also drop the unnecessary check for HT40 - this register can always be written. This patch has been reported to improve HT40 stability and throughput in some environments. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-09-30Revert "ath9k_hw: reduce ANI firstep range for older chips"Felix Fietkau1-1/+3
This reverts commit 09efc56345be4146ab9fc87a55c837ed5d6ea1ab I've received reports that this change is decreasing throughput in some rare conditions on an AR9280 based device Cc: stable@vger.kernel.org Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-09-30mwifiex: remove unnecessary rx_q lockAvinash Patil4-10/+0
SKB lists have their own lock. So this lock is not needed. Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-09-30mwifiex: do not decrement rx_pending count twiceAvinash Patil1-6/+2
This patch fixes an issue with rx processing function where we were decrementing rx_pending count twice. Patch also queues correct main_work item when rx_pending count reaches low watermark. Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Cathy Luo <cluo@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-09-30mwifiex: fix soft lockup during iperf UDP RXAvinash Patil1-1/+2
A soft lockup was observed on ARM multicore platform while UDP RX iperf was running on station. Reason for this is delay_main_task was not taken into consideration while jumping to process_start. Now if delay_main_task is true, we would exit mwifiex_main_process instead of going to process_start again. This ensure other process is scheduled on this CPU and soft lockup is avoided. Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Kevin Gan <ganhy@marvell.com> Signed-off-by: Marc Yang <yangyang@marvell.com> Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Cathy Luo <cluo@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-09-30MAINTAINERS: change rt2x00 maintainerStanislaw Gruszka1-2/+1
After short chat with Ivo, we decided that I'll take maintenance of rt2x00 driver. Thanks for Ivo's great work in the past! Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Acked-by: Ivo Van Doorn <ivdoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-09-30ath9k_hw: disable hardware ad-hoc flag on ar934x rev 3Felix Fietkau2-3/+10
On AR934x rev 3, settin the ad-hoc flag completely messes up hardware state - beacons get stuck, almost no packets make it out, hardware is constantly reset. When leaving out that flag and setting up the hw like in AP mode, TSF timers won't be automatically synced, but at least the rest works. AR934x rev 2 and older are not affected by this bug Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-09-30ath9k: use ah->get_mac_revision for all SoC devices if availableFelix Fietkau1-7/+4
It is needed for AR934x as well Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-09-30ath5k: add missing include for debug codeFelix Fietkau1-0/+1
Needed for calling vmalloc()/vfree() Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-09-30rtlwifi: rtl8188ee: rtl8723ae: rtl8821ae: Initialize some variablesLarry Finger7-18/+18
In a number of places, kmalloc or valloc were used to acquire memory. To ensure that these locations are correctly initialized, the calls were changed to kzalloc and vzalloc. The change fixes a problem that was causing HT operations to be cancelled. Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-09-30rtlwifi: rtl8188ee: rtl8192com: rtl8192cu: rtl8192ee: rtl8723ae: rtl87323be: ↵Larry Finger10-139/+45
rtl8821ae: Use common cmd_send_packet A locking problem was found in routine _rtl92ee_cmd_send_packet() that led to system freezes. Upon inspection, several drivers had the same problem; however, the routines all used the same code. The common code has been moved into rtlwifi. Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-09-30rtlwifi: rtl8192ce: rtl8192common: Update for latest version of Realtek driversLarry Finger18-973/+534
Realtek released new drivers on 06/28/2014. These changes implement all their changes into the kernel version of the driver. In addition, these modifications are part of the process of unifying the Realtek and kernel code bases. Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-09-30rtlwifi: rtl8723be: Update driver to match Realtek release of 06/28/14Larry Finger30-3167/+3833
This patch updates the driver to match the latest Realtek release, and it is an important step in getting the internal code source at Realtek to match the code in the kernel. The primary reason for this is to make it easier for Realtek to maintain the kernel source without requiring an intermediate like me. In this process of merging the two source repositories, there are a lot of changes in both, and this commit is rather large. Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-09-30rtlwifi: rtl8723ae: Update driver to match 06/28/14 Realtek versionLarry Finger38-4836/+5403
Not only does this patch update the driver to match the latest Realtek release, it is an important step in getting the internal code source at Realtek to match the code in the kernel. The primary reason for this is to make it easier for Realtek to maintain the kernel source without requiring an intermediate like me. In this process of merging the two source repositories, there are a lot of changes in both, and this commit is rather large. Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-09-30rtlwifi: rtl8192ee: Move driver from staging to the regular treeLarry Finger25-1/+15380
This driver was entered into staging a few cycles ago because there was not time to integrate the Realtek version into the support routines in the kernel. Now that there is an effort to converg the code base from Linux and the Realtek repo, it is time to move this driver. In addition, all the updates included in the 06/28/2014 version of the Realtek drivers are included here. With this change, it will be necessary to delete the staging driver. That will be handled in a separate patch. As it impacts the staging tree, such a patch is sent to a different destination. Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-09-30rtlwifi: rtl8188ee: rtl8821ae: Fix a queue locking problemLarry Finger3-2/+5
The code fails to lock the skb queue, which leads to a number of problems. This patch also fixes a Sparse warning about using a memset of 1 byte. Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: troy_tan@realsil.com.cn Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-09-30bcma: use chipcommon node from DT for SoC GPIO chipRafał Miłecki2-0/+16
This will allow us to define GPIO-attached devices (LEDs, buttons) in the the device tree. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Acked-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-09-30bcma: register bcma as device tree driverHauke Mehrtens5-1/+168
This driver is used by the bcm53xx ARM SoC code. Now it is possible to give the address of the chipcommon core in device tree and bcma will search for all the other cores. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Acked-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-09-30mwifiex: add more dump information for PCIe interfaceAmitkumar Karwar2-0/+11
We will now dump MAC, APU, CIU, ICU firmware memory segments also for PCIe interface. Following is the updated userspace script which reads firmware dump information. mwifiex_pcie_fw_dump.sh: #!/bin/bash ethtool --set-dump mlan0 0 ethtool --get-dump mlan0 ethtool --get-dump mlan0 data /tmp/ITCM.log ethtool --set-dump mlan0 1 ethtool --get-dump mlan0 ethtool --get-dump mlan0 data /tmp/DTCM.log ethtool --set-dump mlan0 2 ethtool --get-dump mlan0 ethtool --get-dump mlan0 data /tmp/SQRAM.log ethtool --set-dump mlan0 3 ethtool --get-dump mlan0 ethtool --get-dump mlan0 data /tmp/IRAM.log ethtool --set-dump mlan0 4 ethtool --get-dump mlan0 ethtool --get-dump mlan0 data /tmp/APU.log ethtool --set-dump mlan0 5 ethtool --get-dump mlan0 ethtool --get-dump mlan0 data /tmp/CIU.log ethtool --set-dump mlan0 6 ethtool --get-dump mlan0 ethtool --get-dump mlan0 data /tmp/ICU.log ethtool --set-dump mlan0 7 ethtool --get-dump mlan0 ethtool --get-dump mlan0 data /tmp/MAC.log Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Cathy Luo <cluo@marvell.com> Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-09-30mwifiex: error path handling in pcie firmware dumpAmitkumar Karwar1-4/+7
This patch takes care of missing error paths in firmware dump. Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Cathy Luo <cluo@marvell.com> Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-09-30Bluetooth: btusb: remove redundant lock variableAmitkumar Karwar1-4/+0
This variable is nowhere used in the code. Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2014-09-30Bluetooth: btmrvl: support Marvell Bluetooth device SD8887Xinming Hu2-2/+34
This patch adds driver support for marvell SD8887 chip. Signed-off-by: Xinming Hu <huxm@marvell.com> Signed-off-by: Kevin Gan <ganhy@marvell.com> Signed-off-by: Cathy Luo <cluo@marvell.com> Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2014-09-30Bluetooth: btmrvl: rename definitions from 88xx to 8897Amitkumar Karwar1-2/+2
Register offsets are different for SD8897 and newer chip SD8887. We can not have common btmrvl_sdio_card_reg map for them. Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2014-09-29Bluetooth: 6lowpan: Enable multicast supportJukka Rissanen1-1/+2
Set multicast support for 6lowpan network interface. This is needed in every network interface that supports IPv6. Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2014-09-29Bluetooth: 6lowpan: Ensure header compression does not corrupt IPv6 headerJukka Rissanen1-52/+83
If skb is going to multiple destinations, then make sure that we do not overwrite the common IPv6 headers. So before compressing the IPv6 headers, we copy the skb and that is then sent to 6LoWPAN Bluetooth devices. This is a similar patch as what was done for IEEE 802.154 6LoWPAN in commit f19f4f9525cf3 ("ieee802154: 6lowpan: ensure header compression does not corrupt ipv6 header") Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2014-09-29Bluetooth: 6lowpan: Make sure skb exists before accessing itJukka Rissanen1-0/+6
We need to make sure that the saved skb exists when resuming or suspending a CoC channel. This can happen if initial credits is 0 when channel is connected. Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2014-09-27rtlwifi: Fix problems with building an allyesconfigLarry Finger20-833/+223
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-09-27rtlwifi: rtl8821ae: Move driver from staging to regular treeLarry Finger28-6/+26865
This driver was entered into staging a few cycles ago because there was not time to integrate the Realtek version into the support routines in the kernel. Now that there is an effort to converg the code base from Linux and the Realtek repo, it is time to move this driver. In addition, all the updates included in the 06/28/2014 version of the Realtek drivers are included here. With this change, it will be necessary to delete the staging driver. That will be handled in a separate patch. As it impacts the staging tree, such a patch is sent to a different destination. Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-09-27rtlwifi: rtl8188ee: Update driver to match Realtek release of 06282014Larry Finger25-4248/+4863
Not only does this patch update the driver to match the latest Realtek release, it is an important step in getting the internal code source at Realtek to match the code in the kernel. The primary reason for this is to make it easier for Realtek to maintain the kernel source without requiring an intermediate like me. In this process of merging the two source repositories, there are a lot of changes in both, and this commit is rather large. Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-09-27rtlwifi: Finish modifying core routines for new driversLarry Finger9-133/+174
Addition of the new drivers and the update to a new version for the others lead to changes in all the core routines. Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
generated by cgit v1.2.3 (git 2.39.0) at 2025-10-03 09:09:11 +0300