| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The System Configuration (syscon) driver is an important one, which
effects many ARM-SoC based platforms. I'm adding Arnd as a primary
reviewer as he is highly competent in this area and has a keen
interest in ARM-SoC.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Extend the entry for Samsung MFD drivers for PMIC devices (Power
Management Integrated Circuit) with bindings documentation, clock
(clk-s2mps11.c) and RTC drivers (rtc-s5m.c).
These PMIC devices are used on many Exynos-based boards like Arndale
Octa (S2MPS11), Gear 2 (S2MPS14).
Add Krzysztof Kozlowski as a supporter for reviewing them.
I am not the author of these drivers. However I have recently
contributed to most of them and I have access to datasheets and hardware.
Cc: Sangbeom Kim <sbkim73@samsung.com>
CC: Mike Turquette <mturquette@linaro.org>
CC: Stephen Boyd <sboyd@codeaurora.org>
CC: Alessandro Zummo <a.zummo@towertech.it>
CC: Alexandre Belloni <alexandre.belloni@free-electrons.com>
CC: Liam Girdwood <lgirdwood@gmail.com>
CC: Mark Brown <broonie@kernel.org>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The GPIO subsystem provides dummy GPIO consumer functions if GPIOLIB is
not enabled. Hence drivers that depend on GPIOLIB, but use GPIO consumer
functionality only, can still be compiled if GPIOLIB is not enabled.
Relax the dependency on GPIOLIB if COMPILE_TEST is enabled, where
appropriate.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The defined struct max77686_opmode_data isn't used neither by
the max77686 mfd driver nor the drivers for its sub-devices.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
I noticed the PMIC configuration on 37xx-evm won't actually shut down
the voltages during off-idle. Turns out 37xx-evm needs the AC charger
state transitions disabled like we are doing for SDP and LDP in the
legacy booting case.
Let's fix this for device tree based booting by setting up the quirk
flag based on the compatible flag. And let's also use the existing
define for STARTON_CHG.
Note that SDP and EVM do not have the PMIC clken wired to gate the
the oscillator while LDP has.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Fix typo in 'Multifunction'.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
This soft reset used to be located after the register patch had been
applied, but has since moved to before the patch is applied. At the new
location there is no requirement to do a register sync as no register
writes will have happened yet.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
This patch adds device tree binding documentation for
the flash cell of the Maxim max77693 multifunctional device.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Constify in various drivers configuration data which is not modified:
- regmap_irq_chip,
- individual regmap_irq's in array,
- regmap_config,
- irq_domain_ops,
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
'ib-mfd-i2c-input-chrome-4.2' into ibs-for-mfd-merged
|
|
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Some ECs need a little time for waking up before they can accept
SPI data at a high speed. This is configurable via a DT property
"google,cros-ec-spi-pre-delay".
This patch makes the cros_ec_spi driver to cause a delay before
the beginning of a SPI transaction, to make sure that the EC has
already woken up, if the property has been defined in the DTS.
Signed-off-by: Alexandru M Stan <amstan@chromium.org>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Some ECs need a little time for waking up before they can accept
SPI data at a high speed. Add a "google,cros-ec-spi-pre-delay"
property to the DT binding to configure this.
If this property isn't set, then no delay will be added. However,
if set it will cause a delay equal to the value passed to it to
be inserted at the beginning of a transaction.
Signed-off-by: Alexandru M Stan <amstan@chromium.org>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Chromebooks can have more than one Embedded Controller so the
cros_ec device id has to be incremented for each EC registered.
Add a new structure to represent multiple EC as different char
devices (e.g: /dev/cros_ec, /dev/cros_pd). It connects to
cros_ec_device and allows sysfs inferface for cros_pd.
Also reduce number of allocated objects, make chromeos sysfs
class object a static and add refcounting to prevent object
deletion while command is in progress.
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-by: Dmitry Torokhov <dtor@chromium.org>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Add proto v3 support to the SPI, I2C, and LPC.
Signed-off-by: Stephen Barber <smbarber@chromium.org>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Gwendal Grignou <gwendal@chromium.org>
Tested-by: Gwendal Grignou <gwendal@chromium.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Add support in cros_ec.c to handle EC host command protocol v3.
For v3+, probe for maximum shared protocol version and max
request, response, and passthrough sizes. For now, this will
always fall back to v2, since there is no bus-specific code
for handling proto v3 packets.
Signed-off-by: Stephen Barber <smbarber@chromium.org>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Gwendal Grignou <gwendal@chromium.org>
Tested-by: Gwendal Grignou <gwendal@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The MFD driver should only have the logic to instantiate its child devices
and setup any shared resources that will be used by the subdevices drivers.
The cros_ec MFD is more complex than expected since it also has helpers to
communicate with the EC. So the driver will only get more bigger as other
protocols are supported in the future. So move the communication protocol
helpers to its own driver as drivers/platform/chrome/cros_ec_proto.c.
Suggested-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Update cros_ec_commands.h to the latest version in the EC
firmware sources and add power domain and passthru commands.
Also, update lightbar to use new command names.
Signed-off-by: Stephen Barber <smbarber@chromium.org>
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Gwendal Grignou <gwendal@chromium.org>
Tested-by: Gwendal Grignou <gwendal@chromium.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Commit 1b84f2a4cd4a ("mfd: cros_ec: Use fixed size arrays to transfer
data with the EC") modified the struct cros_ec_command fields to not
use pointers for the input and output buffers and use fixed length
arrays instead.
This change was made because the cros_ec ioctl API uses that struct
cros_ec_command to allow user-space to send commands to the EC and
to get data from the EC. So using pointers made the API not 64-bit
safe. Unfortunately this approach was not flexible enough for all
the use-cases since there may be a need to send larger commands
on newer versions of the EC command protocol.
So to avoid to choose a constant length that it may be too big for
most commands and thus wasting memory and CPU cycles on copy from
and to user-space or having a size that is too small for some big
commands, use a zero-length array that is both 64-bit safe and
flexible. The same buffer is used for both output and input data
so the maximum of these values should be used to allocate it.
Suggested-by: Gwendal Grignou <gwendal@chromium.org>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
If the EC device tree node has sub-nodes, try to instantiate them as
MFD sub-devices. We can configure the EC features provided by the board.
Signed-off-by: Todd Broch <tbroch@chromium.org>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Gwendal Grignou <gwendal@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Parent and device were pointing to the same device structure.
Parent is unused, removed.
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Tested-by: Stephen Barber <smbarber@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-by: Puthikorn Voravootivat <puthik@chromium.org>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Now that the axp20x-regulators driver supports different variants of the
AXP family, we can enable regulator support for AXP22X without the risk
of incorrectly configuring regulators.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Add the list of regulators for AXP22x to the DT bindings.
This includes the names and supply names.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Add AXP22X regulator definitions and variant id associations.
This introduces a new "switch" type output for one of the regulators.
It is a switchable secondary output of one regulator, with the same
voltage level as the primary output.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
[wens@csie.org: Moved variant choosing to multi family support patch]
[wens@csie.org: Add dc-dc work frequency range]
[wens@csie.org: Add "switch" type output regulator DC1SW]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Rework the AXP20X_ macros and probe function to support the several chip
families, so that each family can define it's own set of regulators.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
[wens@csie.org: Support different DC-DC work frequency ranges]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Add AXP221 to the list of supported devices.
Also replace any mention of AXP20x in the document with a
generic "PMIC".
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Add support for the AXP22x PMIC devices to the existing AXP20x driver.
This includes the AXP221 and AXP223, which are identical except for
the external data bus. Only AXP221 is added for now. AXP223 will be
added after it's Reduced Serial Bus (RSB) interface is supported.
AXP22x defines a new set of registers, power supplies and regulators,
but most of the API is similar to the AXP20x ones.
A new irq chip definition is used, even though the available interrupts
on AXP22x is a subset of those on AXP20x. This is done so the interrupt
numbers match those on the datasheet.
This patch only enables the interrupts, system power-off function, and PEK
sub-device. The regulator driver must first support different variants
before we enable it from the mfd driver.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
[wens@csie.org: fix interrupts and move regulators to separate patch]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull ext4 fixes from Ted Ts'o:
"Some miscellaneous bug fixes and some final on-disk and ABI changes
for ext4 encryption which provide better security and performance"
* tag 'for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: fix growing of tiny filesystems
ext4: move check under lock scope to close a race.
ext4: fix data corruption caused by unwritten and delayed extents
ext4 crypto: remove duplicated encryption mode definitions
ext4 crypto: do not select from EXT4_FS_ENCRYPTION
ext4 crypto: add padding to filenames before encrypting
ext4 crypto: simplify and speed up filename encryption
|
|
Pull drm fixes from Dave Airlie:
"One intel fix, one rockchip fix, and a bunch of radeon fixes for some
regressions from audio rework and vm stability"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/i915/chv: Implement WaDisableShadowRegForCpd
drm/radeon: fix userptr return value checking (v2)
drm/radeon: check new address before removing old one
drm/radeon: reset BOs address after clearing it.
drm/radeon: fix lockup when BOs aren't part of the VM on release
drm/radeon: add SI DPM quirk for Sapphire R9 270 Dual-X 2G GDDR5
drm/radeon: adjust pll when audio is not enabled
drm/radeon: only enable audio streams if the monitor supports it
drm/radeon: only mark audio as connected if the monitor supports it (v3)
drm/radeon/audio: don't enable packets until the end
drm/radeon: drop dce6_dp_enable
drm/radeon: fix ordering of AVI packet setup
drm/radeon: Use drm_calloc_ab for CS relocs
drm/rockchip: fix error check when getting irq
MAINTAINERS: add entry for Rockchip drm drivers
|
|
git://anongit.freedesktop.org/drm-intel into drm-fixes
Just a single intel fix
* tag 'drm-intel-fixes-2015-04-30' of git://anongit.freedesktop.org/drm-intel:
drm/i915/chv: Implement WaDisableShadowRegForCpd
|
|
https://github.com/markyzq/kernel-drm-rockchip into drm-fixes
one fix and maintainers update
* 'drm-next0420' of https://github.com/markyzq/kernel-drm-rockchip:
drm/rockchip: fix error check when getting irq
MAINTAINERS: add entry for Rockchip drm drivers
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is three logical fixes (as 5 patches).
The 3ware class of drivers were causing an oops with multiqueue by
tearing down the command mappings after completing the command (where
the variables in the command used to tear down the mapping were
no-longer valid). There's also a fix for the qnap iscsi target which
was choking on us sending it commands that were too long and a fix for
the reworked aha1542 allocating GFP_KERNEL under a lock"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
3w-9xxx: fix command completion race
3w-xxxx: fix command completion race
3w-sas: fix command completion race
aha1542: Allocate memory before taking a lock
SCSI: add 1024 max sectors black list flag
|
|
Pull slave dmaengine fixes from Vinod Koul:
"Here are the fixes in dmaengine subsystem for rc2:
- privatecnt fix for slave dma request API by Christopher
- warn fix for PM ifdef in usb-dmac by Geert
- fix hardware dependency for xgene by Jean"
* 'next' of git://git.infradead.org/users/vkoul/slave-dma:
dmaengine: increment privatecnt when using dma_get_any_slave_channel
dmaengine: xgene: Set hardware dependency
dmaengine: usb-dmac: Protect PM-only functions to kill warning
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux
Pull powerpc fixes from Michael Ellerman:
- build fix for SMP=n in book3s_xics.c
- fix for Daniel's pci_controller_ops on powernv.
- revert the TM syscall abort patch for now.
- CPU affinity fix from Nathan.
- two EEH fixes from Gavin.
- fix for CR corruption from Sam.
- selftest build fix.
* tag 'powerpc-4.1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux:
powerpc/powernv: Restore non-volatile CRs after nap
powerpc/eeh: Delay probing EEH device during hotplug
powerpc/eeh: Fix race condition in pcibios_set_pcie_reset_state()
powerpc/pseries: Correct cpu affinity for dlpar added cpus
selftests/powerpc: Fix the pmu install rule
Revert "powerpc/tm: Abort syscalls in active transactions"
powerpc/powernv: Fix early pci_controller_ops loading.
powerpc/kvm: Fix SMP=n build error in book3s_xics.c
|
|
The estimate of necessary transaction credits in ext4_flex_group_add()
is too pessimistic. It reserves credit for sb, resize inode, and resize
inode dindirect block for each group added in a flex group although they
are always the same block and thus it is enough to account them only
once. Also the number of modified GDT block is overestimated since we
fit EXT4_DESC_PER_BLOCK(sb) descriptors in one block.
Make the estimation more precise. That reduces number of requested
credits enough that we can grow 20 MB filesystem (which has 1 MB
journal, 79 reserved GDT blocks, and flex group size 16 by default).
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Eric Sandeen <sandeen@redhat.com>
|
|
fallocate() checks that the file is extent-based and returns
EOPNOTSUPP in case is not. Other tasks can convert from and to
indirect and extent so it's safe to check only after grabbing
the inode mutex.
Signed-off-by: Davide Italiano <dccitaliano@gmail.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@vger.kernel.org
|
|
Currently it is possible to lose whole file system block worth of data
when we hit the specific interaction with unwritten and delayed extents
in status extent tree.
The problem is that when we insert delayed extent into extent status
tree the only way to get rid of it is when we write out delayed buffer.
However there is a limitation in the extent status tree implementation
so that when inserting unwritten extent should there be even a single
delayed block the whole unwritten extent would be marked as delayed.
At this point, there is no way to get rid of the delayed extents,
because there are no delayed buffers to write out. So when a we write
into said unwritten extent we will convert it to written, but it still
remains delayed.
When we try to write into that block later ext4_da_map_blocks() will set
the buffer new and delayed and map it to invalid block which causes
the rest of the block to be zeroed loosing already written data.
For now we can fix this by simply not allowing to set delayed status on
written extent in the extent status tree. Also add WARN_ON() to make
sure that we notice if this happens in the future.
This problem can be easily reproduced by running the following xfs_io.
xfs_io -f -c "pwrite -S 0xaa 4096 2048" \
-c "falloc 0 131072" \
-c "pwrite -S 0xbb 65536 2048" \
-c "fsync" /mnt/test/fff
echo 3 > /proc/sys/vm/drop_caches
xfs_io -c "pwrite -S 0xdd 67584 2048" /mnt/test/fff
This can be theoretically also reproduced by at random by running fsx,
but it's not very reliable, though on machines with bigger page size
(like ppc) this can be seen more often (especially xfstest generic/127)
Signed-off-by: Lukas Czerner <lczerner@redhat.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@vger.kernel.org
|
|
This patch removes duplicated encryption modes which were already in
ext4.h. They were duplicated from commit 3edc18d and commit f542fb.
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: Michael Halcrow <mhalcrow@google.com>
Cc: Andreas Dilger <adilger.kernel@dilger.ca>
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
|
|
This patch adds a tristate EXT4_ENCRYPTION to do the selections
for EXT4_FS_ENCRYPTION because selecting from a bool causes all
the selected options to be built-in, even if EXT4 itself is a
module.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
|
|
Pull networking fixes from David Miller:
1) Receive packet length needs to be adjust by 2 on RX to accomodate
the two padding bytes in altera_tse driver. From Vlastimil Setka.
2) If rx frame is dropped due to out of memory in macb driver, we leave
the receive ring descriptors in an undefined state. From Punnaiah
Choudary Kalluri
3) Some netlink subsystems erroneously signal NLM_F_MULTI. That is
only for dumps. Fix from Nicolas Dichtel.
4) Fix mis-use of raw rt->rt_pmtu value in ipv4, one must always go via
the ipv4_mtu() helper. From Herbert Xu.
5) Fix null deref in bridge netfilter, and miscalculated lengths in
jump/goto nf_tables verdicts. From Florian Westphal.
6) Unhash ping sockets properly.
7) Software implementation of BPF divide did 64/32 rather than 64/64
bit divide. The JITs got it right. Fix from Alexei Starovoitov.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (30 commits)
ipv4: Missing sk_nulls_node_init() in ping_unhash().
net: fec: Fix RGMII-ID mode
net/mlx4_en: Schedule napi when RX buffers allocation fails
netxen_nic: use spin_[un]lock_bh around tx_clean_lock
net/mlx4_core: Fix unaligned accesses
mlx4_en: Use correct loop cursor in error path.
cxgb4: Fix MC1 memory offset calculation
bnx2x: Delay during kdump load
net: Fix Kernel Panic in bonding driver debugfs file: rlb_hash_table
net: dsa: Fix scope of eeprom-length property
net: macb: Fix race condition in driver when Rx frame is dropped
hv_netvsc: Fix a bug in netvsc_start_xmit()
altera_tse: Correct rx packet length
mlx4: Fix tx ring affinity_mask creation
tipc: fix problem with parallel link synchronization mechanism
tipc: remove wrong use of NLM_F_MULTI
bridge/nl: remove wrong use of NLM_F_MULTI
bridge/mdb: remove wrong use of NLM_F_MULTI
net: sched: act_connmark: don't zap skb->nfct
trivial: net: systemport: bcmsysport.h: fix 0x0x prefix
...
|
|
Here the "other side" refers to the guest or host.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
With my job change kernel work will be "own time"; I'm keeping lguest
and modules (and the virtio standards work), but virtio kernel has to
go.
This makes it clear that Michael is in charge. He's good, but having
me watch over his shoulder won't help.
Good luck Michael!
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client
Pull Ceph RBD fix from Sage Weil.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
rbd: end I/O the entire obj_request on error
|
|
If we don't do that, then the poison value is left in the ->pprev
backlink.
This can cause crashes if we do a disconnect, followed by a connect().
Tested-by: Linus Torvalds <torvalds@linux-foundation.org>
Reported-by: Wen Xu <hotdog3645@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When we end I/O struct request with error, we need to pass
obj_request->length as @nr_bytes so that the entire obj_request worth
of bytes is completed. Otherwise block layer ends up confused and we
trip on
rbd_assert(more ^ (which == img_request->obj_request_count));
in rbd_img_obj_callback() due to more being true no matter what. We
already do it in most cases but we are missing some, in particular
those where we don't even get a chance to submit any obj_requests, due
to an early -ENOMEM for example.
A number of obj_request->xferred assignments seem to be redundant but
I haven't touched any of obj_request->xferred stuff to keep this small
and isolated.
Cc: Alex Elder <elder@linaro.org>
Cc: stable@vger.kernel.org # 3.10+
Reported-by: Shawn Edwards <lesser.evil@gmail.com>
Reviewed-by: Sage Weil <sage@redhat.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
|
|
This obscures the length of the filenames, to decrease the amount of
information leakage. By default, we pad the filenames to the next 4
byte boundaries. This costs nothing, since the directory entries are
aligned to 4 byte boundaries anyway. Filenames can also be padded to
8, 16, or 32 bytes, which will consume more directory space.
Change-Id: Ibb7a0fb76d2c48e2061240a709358ff40b14f322
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
|
|
Avoid using SHA-1 when calculating the user-visible filename when the
encryption key is available, and avoid decrypting lots of filenames
when searching for a directory entry in a directory block.
Change-Id: If4655f144784978ba0305b597bfa1c8d7bb69e63
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
Pull btrfs fixes from Chris Mason:
"A few more btrfs fixes.
These range from corners Filipe found in the new free space cache
writeback to a grab bag of fixes from the list"
* 'for-linus-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: btrfs_release_extent_buffer_page didn't free pages of dummy extent
Btrfs: fill ->last_trans for delayed inode in btrfs_fill_inode.
btrfs: unlock i_mutex after attempting to delete subvolume during send
btrfs: check io_ctl_prepare_pages return in __btrfs_write_out_cache
btrfs: fix race on ENOMEM in alloc_extent_buffer
btrfs: handle ENOMEM in btrfs_alloc_tree_block
Btrfs: fix find_free_dev_extent() malfunction in case device tree has hole
Btrfs: don't check for delalloc_bytes in cache_save_setup
Btrfs: fix deadlock when starting writeback of bg caches
Btrfs: fix race between start dirty bg cache writeout and bg deletion
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"Not too much here, but we've addressed a couple of nasty issues in the
dma-mapping code as well as adding the halfword and byte variants of
load_acquire/store_release following on from the CSD locking bug that
you fixed in the core.
- fix perf devicetree warnings at probe time
- fix memory leak in __dma_free()
- ensure DMA buffers are always zeroed
- show IRQ trigger in /proc/interrupts (for parity with ARM)
- implement byte and halfword access for smp_{load_acquire,store_release}"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: perf: Fix the pmu node name in warning message
arm64: perf: don't warn about missing interrupt-affinity property for PPIs
arm64: add missing PAGE_ALIGN() to __dma_free()
arm64: dma-mapping: always clear allocated buffers
ARM64: Enable CONFIG_GENERIC_IRQ_SHOW_LEVEL
arm64: add missing data types in smp_load_acquire/smp_store_release
|
