summaryrefslogtreecommitdiff
AgeCommit message (Collapse)AuthorFilesLines
2017-12-27ARM: dts: imx6qdl-hummingboard2: Remove leading zero in unit addressFabio Estevam1-1/+1
Remove the leading zero from unit address to fix the following build warning with W=1: arch/arm/boot/dts/imx6dl-hummingboard2.dtb: Warning (unit_address_format): Node /soc/aips-bus@2100000/i2c@21a0000/codec@0a unit name should not have leading 0s Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2017-12-26ARM: dts: ls1021a: add support for Moxa UC-8410A open platformSZ Lin2-0/+242
Add support for Moxa UC-8410A open platform The UC-8410A computing platform is designed for embedded communication-centric industrial applications The features of UC-8410A are: * QSPI flash * SD slot * 3x LAN * 8x RS-232/422/485 ports, software-selectable * Mini PCIe form factor with PCIe/USB signal * 2x USB host * TPM * Watchdog * RTC * User LEDs * Beeper * Push button Signed-off-by: Jimmy Chen <jimmy.chen@moxa.com> Signed-off-by: Harry YJ Jhou <harryyj.jhou@moxa.com> Signed-off-by: SZ Lin <sz.lin@moxa.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2017-12-26ARM: dts: imx51-babbage: Fix the 26MHz clock modellingFabio Estevam1-17/+50
On imx51-babbage there is a 26MHz oscillator that is gated by GPIO3_1. The output of this clock feeds audio codec clock and USB PHY clocks, which are gated by GPIO4_26 and GPIO2_1 respectively. Fix the clock representation by properly using gpio-gate-clock. The clock nodes can be moved out of the 'clocks' node. Based on a commit from Lucas Stach for imx51-zii-rdu1 board. This also fixes the following build warning with W=1: arch/arm/boot/dts/imx51-babbage.dtb: Warning (unit_address_vs_reg): Node /clocks/codec_clock has a reg or ranges property, but no unit name Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2017-12-26ARM: dts: vf610-zii-dev-rev-b: add PHYs for switch2Russell King1-0/+17
Switch 2 has an 88e1545 PHY behind it, which is a quad PHY. Only the first three PHYs are used, the remaining PHY is unused. When we wire up the SFF sockets in a later commit, the omission of this causes the fourth PHY to be used for port 3. Specifying the PHYs in DT avoids the auto-probing of the bus, and discovery of this PHY. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2017-12-26ARM: dts: vf610-zii-dev-rev-b: fix interrupt for GPIO expanderRussell King1-1/+2
The interrupt specification for the GPIO expander is wrong - the expander is wired to PTB28, which is GPIO98. GPIO98 is on gpio chip 3, not 2. In addition, the device is missing a required property. Interrupt controllers must have the "interrupt-controller" property specified. Add this. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2017-12-26ARM: dts: vf610-zii-dev: enable edma1Russell King1-0/+4
EDMA1 is required for the SPI controller used on the ZII boards to be functional. Enable EDMA1. Fixes: 14c416336820 ("ARM: dts: vfxxx: Enable DMA for DSPI on Vybrid") Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2017-12-26ARM: dts: ls1021a-twr: Remove extra clock cellFabio Estevam1-1/+1
There is an extraneous '1' cell in the clock phandle, which causes the following build warning: arch/arm/boot/dts/ls1021a-twr.dtb: Warning (clocks_property): Property 'clocks', cell 1 is not a phandle reference in /soc/i2c@2190000/sgtl5000@a arch/arm/boot/dts/ls1021a-twr.dtb: Warning (clocks_property): Missing property '#clock-cells' in node /soc/interrupt-controller@1400000 or bad phandle (referred from /soc/i2c@2190000/sgtl5000@a:clocks[1]) Remove the unneeded extra cell. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2017-12-26ARM: dts: ls1021a-qds: Remove extra clock cellFabio Estevam1-1/+1
There is an extraneous '1' cell in the clock phandle, which causes the following build warning: arch/arm/boot/dts/ls1021a-qds.dtb: Warning (clocks_property): Property 'clocks', cell 1 is not a phandle reference in /soc/i2c@2180000/mux@77/i2c@4/sgtl5000@2a arch/arm/boot/dts/ls1021a-qds.dtb: Warning (clocks_property): Missing property '#clock-cells' in node /soc/interrupt-controller@1400000 or bad phandle (referred from /soc/i2c@2180000/mux@77/i2c@4/sgtl5000@2a:clocks[1]) Remove the unneeded extra cell. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2017-12-26ARM: dts: imx53: add srtc nodePatrick Bruenn1-0/+7
rtc-mxc_v2 driver will add support for the i.MX53 SRTC Note: we keep the 'srtc' label to avoid duplicate with imx53-m53.dtsi Signed-off-by: Patrick Bruenn <p.bruenn@beckhoff.com> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2017-12-26dt-bindings: imx-gpcv2: Fix the unit addressFabio Estevam1-2/+2
In the provided example the unit address does not match the 'reg' value, as IMX7_POWER_DOMAIN_PCIE_PHY is defined as 1. Fix the unit address and avoid using defines in reg as per Rob Herring's recommendation. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com> Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2017-12-26ARM: imx: dts: Use lower case for bindings notationMathieu Malaterre1-1/+1
Improve the DTS files using lower case to fix the following dtc warnings: Warning (simple_bus_reg): Node /XXX@<UPPER> simple-bus unit address format error, expected "<lower>" Converted using the following command: find . -type f \( -iname *.dts -o -iname *.dtsi \) -exec sed -i -e "s/@\([0-9a-fA-FxX\.;:#]+\)\s*{/@\L\1 {/g" -e "s/@0x\(.*\) {/@\1 {/g" -e "s/@0+\(.*\) {/@\1 {/g" {} +^C For simplicity, two sed expressions were used to solve each warnings separately. To make the regex expression more robust a few other issues were resolved, namely setting unit-address to lower case, and adding a whitespace before the the opening curly brace: https://elinux.org/Device_Tree_Linux#Linux_conventions This is a follow up to commit 4c9847b7375a ("dt-bindings: Remove leading 0x from bindings notation") Reported-by: David Daney <ddaney@caviumnetworks.com> Suggested-by: Rob Herring <robh@kernel.org> Signed-off-by: Mathieu Malaterre <malat@debian.org> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2017-12-26ARM: dts: imx6q-h100: use usdhc2 VSELECTMichael Tretter1-22/+3
The uSDHC controller directly provides a VSELECT signal that can be muxed to the external voltage select. Mux the VSELECT directly to avoid using a GPIO. Signed-off-by: Michael Tretter <m.tretter@pengutronix.de> Reviewed-by: Lucas Stach <l.stach@pengutronix.de> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2017-12-26ARM: dts: imx6sx: Add support for PCI power domainFabio Estevam1-0/+14
Previously PCI support was working because the bootloader has previously powered up the PCI power domain. Represent the PCI power domain, so that PCI is functional without relying on the PCI support from the bootloader. Tested on a imx6sx-sdb board with no PCI support in the bootloader. Reported-by: Abel Vesa <abel.vesa@nxp.com> Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com> Reviewed-by: Lucas Stach <l.stach@pengutronix.de> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2017-12-26ARM: dts: imx6sx: Fix PCI non-prefetchable memory rangeFabio Estevam1-1/+1
The third cell of the PCI non-prefetchable memory range should be 0x08000000, so change it accordingly. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2017-12-26ARM: dts: imx6qdl-hummingboard2: rename regulators to match schematicRussell King2-34/+56
Make the regulators match the schematic - name the regulators after one of their schematic supply names, and arrange them into their heirarchy. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2017-12-26ARM: dts: imx6qdl-hummingboard2: add v1.5 som with eMMCRussell King3-0/+120
Add support for the v1.5 SOM with TI Wi-Fi and eMMC. As the pinmux settings are different for the microsom, we need to use a separate board-level dts for this as there is no support for overlays. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2017-12-26ARM: dts: imx6qdl-hummingboard2: add v1.5 som without eMMCRussell King3-0/+118
Add support for the v1.5 SOM with TI Wi-Fi but without eMMC. As the pinmux settings are different for the microsom, we need to use a separate board-level dts for this as there is no support for overlays. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2017-12-26ARM: dts: imx6qdl-hummingboard2: add PWM3 supportRussell King1-0/+12
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2017-12-26ARM: dts: imx6*-hummingboard2: split out eMMC supportRussell King4-26/+74
eMMC is optional on HB2 boards, and may be implemented by the SOM. Move it out of the base HB2 include file. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2017-12-26ARM: dts: imx6*-hummingboard2: rework regulatorsLucas Stach1-14/+14
Name the regulators according to the voltage rails they are feeding in the schematic. The USB 2-4 regulators are fixed regulators and are always on, as they are not a VBUS supply for a single USB host port on the i.MX6, but supply VBUS to ports behind a USB hub and there is currently no way to model this in mainline. Signed-off-by: Lucas Stach <dev@lynxeye.de> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2017-12-26ARM: dts: imx6*-hummingboard2: remove redundant PWM disablesLucas Stach1-8/+0
The PWM nodes are already disabled in the imx6qdl.dtsi, so there is no need to disable them again in the board DTS. Signed-off-by: Lucas Stach <dev@lynxeye.de> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2017-12-26ARM: dts: imx6*-hummingboard2: remove non-mainline property from RTCLucas Stach1-1/+0
Signed-off-by: Lucas Stach <dev@lynxeye.de> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2017-12-26ARM: dts: imx6*-hummingboard2: fix PCIe reset polarityLucas Stach1-1/+1
The driver always uses active-low, but better describe reality in the DT. Signed-off-by: Lucas Stach <dev@lynxeye.de> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2017-12-26ARM: dts: imx6*-hummingboard2: remove LDB nodeLucas Stach1-9/+0
It's disabled by default and the data mapping is supposed to be retrieved from the attached panel driver in mainline. Signed-off-by: Lucas Stach <dev@lynxeye.de> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2017-12-26ARM: dts: imx6*-hummingboard2: add SGTL5000 VDDD supplyLucas Stach1-0/+1
VDDD is supplied by VCC_1P8 on HB2. Signed-off-by: Lucas Stach <dev@lynxeye.de> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2017-12-26ARM: dts: imx6*-hummingboard2: fix formattingLucas Stach1-6/+4
Trivial formatting change. Signed-off-by: Lucas Stach <dev@lynxeye.de> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2017-12-26ARM: dts: imx6*-hummingboard2: convert to more conventional vmmc-supplyRussell King1-7/+19
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2017-12-26ARM: dts: imx6*-hummingboard2: use proper gpio flags definitionsRussell King1-5/+5
Use proper gpio flag definitions for GPIOs rather than using opaque uninformative numbers. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2017-12-26ARM: dts: imx6*-hummingboard2: fix SD card detectRussell King1-2/+2
Fix the SD card detect signal, which was missing the polarity specification, and the pull-up necessary for proper signalling. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2017-12-26ARM: dts: imx6*-hummingboard2: add Broadcom Wi-Fi includeRussell King2-0/+2
The Broadcom Wi-Fi was moved out to a separate include file. Add the include. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2017-12-26ARM: dts: imx6*-hummingboard2: move microsom includes into .dtsRussell King3-1/+2
Move the microsom includes into the .dts files. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2017-12-26ARM: dts: imx6qdl-hummingboard2: rename microsom includeRussell King1-1/+1
Rename microsom include to imx6qdl-sr-som. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2017-12-26ARM: dts: imx6*-hummingboard2: remove ar8035 includeRussell King1-1/+0
Remove the AR8035 include, the file is now gone. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2017-12-26ARM: dts: imx6qdl: add HummingBoard2 boardsJon Nettleton4-0/+651
This adds support for the Hummingboard Gate and Edge devices from SolidRun. Signed-off-by: Jon Nettleton <jon@solid-run.com> Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2017-12-26ARM: dts: TS-4600: add basic device treeSebastien Bourdelin2-0/+80
These device trees add support for the TS-4600 by Technologic Systems. More details here: http://wiki.embeddedarm.com/wiki/TS-4600 Signed-off-by: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2017-12-26of: documentation: add bindings documentation for TS-4600Sebastien Bourdelin1-0/+5
This adds the documentation for the TS-4600 by Technologic Systems. Signed-off-by: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2017-12-26ARM: dts: TS-7970: add basic device treeSebastien Bourdelin4-0/+700
These device trees add support for TS-7970 by Technologic Systems. More details here: https://wiki.embeddedarm.com/wiki/TS-7970 Signed-off-by: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2017-12-26of: documentation: add bindings documentation for TS-7970Sebastien Bourdelin1-0/+6
This adds the documentation for the TS-7970 by Technologic Systems. Signed-off-by: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com> Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2017-12-26ARM: dts: imx7: add Toradex Colibri iMX7D 1GB (eMMC) supportStefan Agner5-1/+108
Add support for the Computer on Module Colibri iMX7D 1GB along with the Colibri Evaluation Board device trees. Follow the usual hierarchic include model, maintaining shared configuration in imx7-colibri.dtsi and imx7-colibri-eval-v3.dtsi respectively. Signed-off-by: Stefan Agner <stefan@agner.ch> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2017-12-26ARM: dts: imx7-colibri: add MCP2515 CAN controllerStefan Agner2-1/+37
The Colibri Evaluation Carrier Board provides a MCP2515 CAN controller connected via SPI. Note that the i.MX 7 provides an internal CAN controller which is much better suited for CAN operations. Using the MCP2515 with a Colibri iMX7 module is mainly useful to test the SPI interface. Signed-off-by: Stefan Agner <stefan@agner.ch> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2017-12-26ARM: dts: imx7-colibri: specify backlight GPIOStefan Agner1-1/+9
The Colibri standard defines SODIMM 71 as backlight enable GPIO. Assign the GPIO to the backlight node in the module level device tree. Signed-off-by: Stefan Agner <stefan@agner.ch> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2017-12-26ARM: dts: imx7-colibri: specify usdhc1 suppliesStefan Agner2-0/+2
The usdhc1 controller instance is used to provide the default SD/MMC capabilities of the Colibri standard. The IO pins are supplied to the SoC on the module whereas the SD-card is powered by the Carrier Board supply. Signed-off-by: Stefan Agner <stefan@agner.ch> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2017-12-26ARM: dts: imx7-colibri: specify cpu-supplyStefan Agner1-1/+1
Specify CPU supply using the "cpu-supply" property instead of the invalid "arm-supply" property. Signed-off-by: Stefan Agner <stefan@agner.ch> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2017-12-26ARM: dts: imx7-colibri: use NAND_CE1 as GPIOStefan Agner1-1/+1
All Colibri iMX7 SKUs use either single-die NAND or eMMC, hence NAND_CE1 is not used on the module and can be used as a GPIO by carrier boards. Signed-off-by: Stefan Agner <stefan@agner.ch> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2017-12-26ARM: dts: imx7-colibri: mux pull-ups where appropriateStefan Agner1-10/+10
Use pull-ups instead of pull-downs for the pins which are already pulled-up externally. Signed-off-by: Stefan Agner <stefan@agner.ch> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2017-12-26ARM: dts: imx7-colibri: make sure multiplexed pins are not activeStefan Agner1-0/+2
The Colibri pins PWM<A> and <D> are multiplexed on the module, make sure the secondary SoC pin is not active. Signed-off-by: Stefan Agner <stefan@agner.ch> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2017-12-26ARM: dts: imx7-colibri: move and rename USB Host power regulatorStefan Agner3-13/+13
The Colibri default which enables USB Host power is not necessarily tied to the OTG2 controller, some carrier board use the pin to control USB power for both controllers. Hence name the pinctrl group more generic. Also move the regulator to the generic eval-v3 device tree since the regulator is always on the carrier board. In the Colibri iMX7S case the regulator is just not used. This allows to reuse the regulator in a upcoming SKU Colibri iMX7D 1GB with eMMC. Signed-off-by: Stefan Agner <stefan@agner.ch> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2017-12-26ARM: dts: imx6sl-evk: Convert from fbdev to drm bindingsMarco Franchi1-24/+24
It is preferred to use the panel compatible string rather than passing the LCD timing in the device tree. So pass the "sii,43wvf1g" compatible string which describes the parallel LCD. Also, pass the 'backlight' property as described in Documentation/devicetree/bindings/display/panel/simple-panel.txt Signed-off-by: Marco Franchi <marco.franchi@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2017-12-26ARM: dts: imx6sl-evk: Rearrange the regulators nodeMarco Franchi1-48/+37
It is not recommended to place regulators inside "simple-bus", so move them out. The motivation for doing this is to make it easier to adding new regulators. Signed-off-by: Marco Franchi <marcofrk@gmail.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2017-12-26ARM: dts: imx6sx-sdb: Convert from fbdev to drm bindingsMarco Franchi1-24/+24
It is preferred to use the panel compatible string rather than passing the LCD timing in the device tree. So pass the "sii,43wvf1g" compatible string, which describes the parallel LCD. Also pass the 'backlight' property as described in Documentation/devicetree/bindings/display/panel/simple-panel.txt Signed-off-by: Marco Franchi <marcofrk@gmail.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
generated by cgit v1.2.3 (git 2.39.0) at 2025-10-03 03:20:05 +0300