| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
On 32-bit platforms packet counters are stored in a net_device_stats struct
as unsigned long integers. As a result, after some time of network activity
an overflow takes place in network packet counters. This patch makes use of
new structs for holding interface statistics.
Signed-off-by: Vasily Ulyanov <vulyanov@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Virtual interface should be deleted after calling unregister_netdevice
since this function ends up with sending updown_intf command to card.
Signed-off-by: Vasily Ulyanov <vulyanov@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
TLV is used to pass ACL data to firmware in start_ap cfg80211 callback.
Use the same approach in set_mac_acl cfg80211 callback.
Signed-off-by: Vasily Ulyanov <vulyanov@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The trailing semicolon is an empty statement that does no operation.
Removing it since it doesn't do anything.
Signed-off-by: Luis de Bethencourt <luisbg@kernel.org>
Acked-by: Jes Sorensen <Jes.Sorensen@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The field spec_ver is IC's specification mask for common code to do proper
process to specified IC. This commit add a field new rate ID for new
generation IC.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
New generation ICs will support 11ac, 5G, n-NSS, etc, so we define a set of
rate ID.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
8822be is 2x2 11ac wifi chip, so report VHT capability to mac80211.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
In files halbtc8822b1ant.c and halbtc8822b2ant.c that I will submit later,
two undesired directives named BT_8822B_1ANT_COEX_DBG and
BT_8822B_2ANT_COEX_DBG will be replaced by boolean variables.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Originally, btcoex controls the antenna of combo card, but solo card
is also needed to setup properly. The new ops are named with suffix
'_wifi_only' opposited to original btc_ops, and new structures and
definitions are also introduced. The wifi_only oly contains four ops that
are initial variable, hw config, scan notify, and switch band notify.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Three steps of connection procedure are scan, enter/leave IPS, auth.
There is no scan between leaving IPS and sending auth, but btcoex use scan
as an important clue that indicates user is going to connect. So add scan
notifications in ips_notify to correct btcoex's state.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The variable will be used by btcoex of 8822be, so we prepare this variable
in advance.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
BT shares 2.4G band but not 5G band, so inform current band to btcoex to
setup antenna properly.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The rtlwifi newer ICs support 80M bandwidth in 5G band, so extend
get_wifi_bw() to know bandwidth 80M that helps btcoex to make correct
decisions.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
There is a possible race in mt76x2_stop_hardware() since pre_tbtt and
dfs tasklets could run during driver cleanup. Fix it disabling all
pending tasklets during device removal
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Acked-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Do not enable DFS state machine if dfs region is set to NL80211_DFS_UNSET
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Add mt76x2_dfs_set_domain routine in order to properly reconfigure
pattern detector when DFS domain has been changed
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Substitute tasklet_kill with tasklet_disable/tasklet_enable in order to
guarantee dfs tasklet can not be executed during dfs parameter
initialization
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Hardware encryption seems to break encrypted unicast mgmt tx.
Unfortunately the hardware TXWI header does not have a bit to indicate
that a frame is software encrypted, so sw-encrypted frames need to use a
different WCID. For that to work, the CCMP PN needs to be generated in
software, which makes things a bit slower, so only do it for keys that
also need to tx management frames.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Fix hw queue configuration since mt76x2 devices use a reverse queue
enumeration respect to mac80211 one:
- 0: AC_BE
- 1: AC_BK
- 2: AC_VI
- 3: AC_VO
The issue can be reproduced sending two concurrent flow using
two separate queues:
- VO: 20Mbps UDP traffic
- BE: TCP traffic
In this scenario the UDP traffic will be blocked by the TCP one.
Fix it configuring properly WMM hw queue parameters
Fixes: 7bc04215a66b ("mt76: add driver code for MT76x2e")
Tested-by: Gaetano Catalli <gaetano.catalli@gmail.com>
Signed-off-by: Gaetano Catalli <gaetano.catalli@gmail.com>
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Acked-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Jiri Pirko says:
====================
mlxsw: Add support for mirror action with flower
Arkadi says:
Add support for mirror action with flower classifier. The first 3 patches
introduce a generic per-block resource infra. The last 4 patches add
support for flow based span.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for mirror action. Only one mirror action can be set per rule.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Spectrum
Introduce extension of mlxsw_afa_ops in order to add/del mirroring and
implement the ops for Spectrum.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Extend SPAN API for ACL case. In case of ACL triggering the MPAR register
shouldn't be configured. This patch also export those helpers for
ACL usage.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The patch extends the trap action for mirroring.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
So far, the caller of mlxsw_afa_block_append_counter needed to allocate
counter index by hand. Benefit from the previously introduced resource
infra and counter_index_get/put callbacks, and allocate the counter
index in place where it is needed, inside the action append function.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since the resource list needs to be used also for other entries different
to fwd_entry_ref, make the list generic. For that purpose, introduce a
resource structure with couple of helpers that the code which need to
store a per-block resource should use.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Spectrum
Introduce extension of mlxsw_afa_ops in order to get/put counter indexes
and implement the ops for Spectrum.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Igor Russkikh says:
====================
Aquantia atlantic driver new devices support
This patchset introduces a support for new Aquantia hardware:
AQC11x family with updated hardware (B1) and firmware (2.x and 3.x branches).
For that, a number of improvements in overall driver model were done:
- Firmware specific ops tables. Firmware 2.x and 3.x series support
functions are now in separate fw2x module.
- PCI module cleanup and simplification done.
- Verified and tested hardware reset process.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For devices with known capabilities of Fibre media type we now report that
to ethtool.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The detailed reset sequence ensures all HW components are in aligned
state before NIC startup. It also supports cards with signed firmware (RBL)
and checks if their FW is valid.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This defines fw2x operations table and corresponding methods.
Some of the functions are being shared with 1.x firmware
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
New AQC cards will have an updated firmware with new binary interface.
This patch extracts firmware specific operations into a separate table
and prepares for the introduction of new fw 2.x and 3.x
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The address to check if HW is not dead/hang could be stored in
capabilities, since it is a constant. Change its name to better reflect
the idea.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
These ops are not related to HW and are now implemented in pci module.
Thus, remove these ops pointers and implementation.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Driver contained a dead code of maintaining multiple pci port instances.
That will never be used since for each pci function a separate NIC
instance is created.
Simplify this, making pci module only responsible for pci resource
management.
NIC initialization is also simplified accordingly.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This removes unnecessary structure copying, and prepares the driver for
separate firmware ops table introduction.
We also remove extra copy of capabilities structure (which is const actually)
and also replace it with a const pointer in aq_nic_cfg.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A number of new AQC devices is going to be released. To support more
flexible capabilities management a number of static caps instances is now
declared. Devices now are mainly differs by supported speeds, but in future
more parameters will be customized. A set of AQC100 devices have
fibre media, not twisted pair - this is also reflected in
new capabilities definitions.
HW level also now directly exports hw_ops for each of A0/B0 hardware.
PCI configuration now uses a device configuration table where each
device ID is explicitly mapped with hardware OPs and capabilities
structures.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
New set of aquantia devices has an upgraded hardware (B1).
The hardware interface is identical to B0. The difference will
be in firmware which is incompatible with old one.
Reorganized and removed duplicate speed and devid definitions
Introduced explicit flow control configuration defines
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2018-01-19
From: Or Gerlitz <ogerlitz@mellanox.com>
=======
First six patches of this series further enhances the mlx5 hairpin support.
The first two patches deal with using different hairpin instances
for flows whose packets have different priorities to align with the port
TX QoS model. The next four patches allow us to do HW spreading
of flows over a set of hairpin pairs using RSS. The last two patches
change the driver to also set the size of the HW hairpin queues.
========
Next four patches from Eran Ben Elisha <eranbe@mellanox.com>:
Add more debug data for TX timeout handling, and further enhance and optimize
TX timeout handling upon lost interrupts, which adds a mechanism for explicitly
polling EQ in case of a TX timeout in order to recover from a lost interrupt.
If this is not the case (no pending EQEs), perform a channels full recovery as
usual.
From Kamal Heib <kamalh@mellanox.com>, Two patches to extend the stats group API
to have an update_stats() callback which will be used to fetch the hardware or
software counters data, this will improve the current API and reduce code
duplication.
From Gal Pressman <galp@mellanox.com>, Last patch, Add likely to the common RX checksum
flow.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Previously it was possible to interrupt processing stats updates because
they were handled in a work queue. Interrupting the stats updates could
lead to a situation where we backup the control message queue. This patch
moves the stats update processing out of the work queue to be processed as
soon as hardware sends a request.
Reported-by: Louis Peens <louis.peens@netronome.com>
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The zeroday builder notices that since Usermode Linux does not
have IO memory, the build fails for them when selecting everything
it can enable.
As the driver is clearly using memory-mapped registers to access
the network adapter, we add depends on HAS_IOMEM to solve this
problem.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pablo Neira Ayuso says:
====================
Netfilter/IPVS updates for net-next
The following patchset contains Netfilter/IPVS updates for your net-next
tree. Basically, a new extension for ip6tables, simplification work of
nf_tables that saves us 500 LoC, allow raw table registration before
defragmentation, conversion of the SNMP helper to use the ASN.1 code
generator, unique 64-bit handle for all nf_tables objects and fixes to
address fallout from previous nf-next batch. More specifically, they
are:
1) Seven patches to remove family abstraction layer (struct nft_af_info)
in nf_tables, this simplifies our codebase and it saves us 64 bytes per
net namespace.
2) Add IPv6 segment routing header matching for ip6tables, from Ahmed
Abdelsalam.
3) Allow to register iptable_raw table before defragmentation, some
people do not want to waste cycles on defragmenting traffic that is
going to be dropped, hence add a new module parameter to enable this
behaviour in iptables and ip6tables. From Subash Abhinov
Kasiviswanathan. This patch needed a couple of follow up patches to
get things tidy from Arnd Bergmann.
4) SNMP helper uses the ASN.1 code generator, from Taehee Yoo. Several
patches for this helper to prepare this change are also part of this
patch series.
5) Add 64-bit handles to uniquely objects in nf_tables, from Harsha
Sharma.
6) Remove log message that several netfilter subsystems print at
boot/load time.
7) Restore x_tables module autoloading, that got broken in a previous
patch to allow singleton NAT hook callback registration per hook
spot, from Florian Westphal. Moreover, return EBUSY to report that
the singleton NAT hook slot is already in instead.
8) Several fixes for the new nf_tables flowtable representation,
including incorrect error check after nf_tables_flowtable_lookup(),
missing Kconfig dependencies that lead to build breakage and missing
initialization of priority and hooknum in flowtable object.
9) Missing NETFILTER_FAMILY_ARP dependency in Kconfig for the clusterip
target. This is due to recent updates in the core to shrink the hook
array size and compile it out if no specific family is enabled via
.config file. Patch from Florian Westphal.
10) Remove duplicated include header files, from Wei Yongjun.
11) Sparse warning fix for the NFPROTO_INET handling from the core
due to missing static function definition, also from Wei Yongjun.
12) Restore ICMPv6 Parameter Problem error reporting when
defragmentation fails, from Subash Abhinov Kasiviswanathan.
13) Remove obsolete owner field initialization from struct
file_operations, patch from Alexey Dobriyan.
14) Use boolean datatype where needed in the Netfilter codebase, from
Gustavo A. R. Silva.
15) Remove double semicolon in dynset nf_tables expression, from
Luis de Bethencourt.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Alexei Starovoitov says:
====================
pull-request: bpf-next 2018-01-19
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) bpf array map HW offload, from Jakub.
2) support for bpf_get_next_key() for LPM map, from Yonghong.
3) test_verifier now runs loaded programs, from Alexei.
4) xdp cpumap monitoring, from Jesper.
5) variety of tests, cleanups and small x64 JIT optimization, from Daniel.
6) user space can now retrieve HW JITed program, from Jiong.
Note there is a minor conflict between Russell's arm32 JIT fixes
and removal of bpf_jit_enable variable by Daniel which should
be resolved by keeping Russell's comment and removing that variable.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The BPF verifier conflict was some minor contextual issue.
The TUN conflict was less trivial. Cong Wang fixed a memory leak of
tfile->tx_array in 'net'. This is an skb_array. But meanwhile in
net-next tun changed tfile->tx_arry into tfile->tx_ring which is a
ptr_ring.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Daniel Borkmann says:
====================
This series adds various misc improvements to BPF: detection
of BPF helper definition misconfiguration for mem/size argument
pairs, csum_diff helper also for XDP, various test cases,
removal of the recently added pure_initcall(), restriction
of the jit sysctls to cap_sys_admin for initns, a minor size
improvement for x86 jit in alu ops, output of complexity limit
to verifier log and last but not least having the event output
more flexible with moving to const_size_or_zero type.
Thanks!
====================
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Similar rationale as in a60dd35d2e39 ("bpf: change bpf_perf_event_output
arg5 type to ARG_CONST_SIZE_OR_ZERO"), change the type to CONST_SIZE_OR_ZERO
such that we can better deal with optimized code. No changes needed in
bpf_event_output() as it can also deal with 0 size entirely (e.g. as only
wake-up signal with empty frame in perf RB, or packet dumps w/o meta data
as another such possibility).
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Given the limit could potentially get further adjustments in the
future, add it to the log so it becomes obvious what the current
limit is w/o having to check the source first. This may also be
helpful for debugging complexity related issues on kernels that
backport from upstream.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
For the BPF_REG_0 (BPF_REG_A in cBPF, respectively), we can use
the short form of the opcode as dst mapping is on eax/rax and
thus save a byte per such operation. Added to add/sub/and/or/xor
for 32/64 bit when K immediate is used. There may be more such
low-hanging fruit to add in future as well.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Given BPF reaches far beyond just networking these days, it was
never intended to allow setting and in some cases reading those
knobs out of a user namespace root running without CAP_SYS_ADMIN,
thus tighten such access.
Also the bpf_jit_enable = 2 debugging mode should only be allowed
if kptr_restrict is not set since it otherwise can leak addresses
to the kernel log. Dump a note to the kernel log that this is for
debugging JITs only when enabled.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
